Yamaha A&E Specifications (XP Series) Specifications
Contents
1. each channel s level shall be independently adjustable The rear panel shall have 12 dB oct HPF switch fe 20 Hz or 55 Hz Rear panel input connectors shall be a 3 pin detachable terminal block and a 3 pin XLR connector for each channel The XLR input shall be wired with pin 2 hot Rear panel output connectors shall be a 5 way binding posts and SPEAKON connectors Dsub15P Data Port connectors shall allow remote control and monitoring The amplifier shall employ patented EEEngine technology Including MOSFET based independent high speed current and voltage buffers without delay circuits to improve slew rate Isolation components shall be provided and output devices shall be mounted by individual screws to minimize sonic degradation caused by vibration The amplifier shall conform to the latest EU RoHS hazardous substances and WEEE directives The amplifier shall have front panel carrying handles It shall use only two standard rack spaces and its dimensions shall be 480 mm W x 456 mm D x 88 mm H 18 7 8 x 17 15 16 x 3 7 16 Weight shall be 14 kg 30 9 lbs The amplifier shall be YAMAHA XP2500 gt 230 V model The power amplifier shall provide two channels of amplification This amplifier shall draw 320 W or less at 1 8 rated power into 4 ohm loads The power amplifier shall be capable of operation from a 230 V 50 Hz line The amplifier shall meet the following performance criteria Power output with both channels driven shall be a minimum of 3902. and WEEE directives The amplifier shall have front panel carrying handles It shall use only two standard rack spaces and its dimensions shall be 480 mm W x 456 mm D x 88 mm H 18 7 8 x 17 15 16 x 3 7 16 Weight shall be 14 kg 30 9 lbs The amplifier shall be YAMAHA XP5000 gt 230 V model The power amplifier shall provide two channels of amplification This amplifier shall draw 500 W or less at 1 8 rated power into 4 ohm loads The power amplifier shall be capable of operation from a 230 V 50 Hz line The amplifier shall meet the following performance criteria Power output with both channels driven shall be a minimum of 750 W per channel with a 4 ohm load 525 W with an 8 ohm load and 1500 W mono bridged into an 8 ohm load Burst peak output with both channels driven shall be a minimum of 1300 W per channel with a 2 ohm load Total harmonic distortion THD N shall be less than 0 1 at 20 Hz 20 kHz half power Intermodulation distortion IMD shall be less than 0 1 using the SMPTE standard of 60 Hz and 7 kHz in a 4 1 ratio respectively with an 8 ohm load Frequency response shall be from 20 Hz to 50 kHz 0 dB 1 dB at 8 ohm Po 1 W Residual noise at 20 Hz 20 kHz shall be less than 70 dBu Input shall be electronically balanced with a minimum impedance of 20 kohm balanced and 10 kohm unbalanced The voltage gain shall be switched to 32 dB 26 dB 4 dBu and the input sensitivity also shall be switched to 4 dBu 12 2 dBu 6 2 dBu Ma
3. rush current limiting shall minimize turn on current surges when multiple units are powered up remotely to prevent AC breaker overload The amplifier shall employ forced air cooling with dual temperature controlled fans variable in speed for minimum acoustic noise Air flow shall be from front to rear The front panel shall have a recessed AC power switch LED indicator The LED indicators shall indicate POWER STAND BY PROTECTION TEMP and REMOTE condition The front panel shall have two 31 step volume knobs one per ch A rear panel mode switch shall provide three modes of input operation Stereo Bridged and Parallel In Parallel input mode each channel s level shall be independently adjustable The rear panel shall have 12 dB oct HPF switch fc 20 Hz or 55 Hz Rear panel input connectors shall be a 3 pin detachable terminal block and a 3 pin XLR connector for each channel The XLR input shall be wired with pin 2 hot Rear panel output connectors shall be a 5 way binding posts and SPEAKON connectors Dsub15P Data Port connectors shall allow remote control and monitoring The amplifier shall employ patented EEEngine technology Including MOSFET based independent high speed current and voltage buffers without delay circuits to improve slew rate Isolation components shall be provided and output devices shall be mounted by individual screws to minimize sonic degradation caused by vibration The amplifier shall conform to the latest EU RoHS hazardous substances
4. B at 8 ohm Po 1 W Residual noise at 20 Hz 20 kHz shall be less than 70 dBu Input shall be electronically balanced with a minimum impedance of 20 kohm balanced and 10 kohm unbalanced The voltage gain shall be switched to 32 dB 26 dB 4 dBu and the input sensitivity also shall be switched to 4 dBu 9 2 dBu 3 2 dBu Maximum input voltage shall be 22 dBu The unweighted signal to noise ratio over the range of 20 Hz 20 kHz shall exceed 100 dB referenced to full output Built in protection circuitry shall monitor voltage and current levels to minimize potential damage from overloads and disable output during shorts DC offset or excessive operating temperatures 130 C The relay shall also delay amplifier connection to the load during turn on for three seconds while the protection circuitry analyzes the load In rush current limiting shall minimize turn on current surges when multiple units are powered up remotely to prevent AC breaker overload The amplifier shall employ forced air cooling with dual temperature controlled fans variable in speed for minimum acoustic noise Air flow shall be from front to rear The front panel shall have a recessed AC power switch LED indicator The LED indicators shall indicate POWER STAND BY PROTECTION TEMP and REMOTE condition The front panel shall have two 31 step volume knobs one per ch A rear panel mode switch shall provide three modes of input operation Stereo Bridged and Parallel In Parallel input mode
5. FET based independent high speed current and voltage buffers without delay circuits to improve slew rate Isolation components shall be provided and output devices shall be mounted by individual screws to minimize sonic degradation caused by vibration The amplifier shall conform to the latest EU RoHS hazardous substances and WEEE directives The amplifier shall have front panel carrying handles It shall use only two standard rack spaces and its dimensions shall be 480 mm W x 456 mm D x 88 mm H 18 7 8 x 17 15 16 x 3 7 16 Weight shall be 14 kg 30 9 lbs The amplifier shall be YAMAHA XP7000 gt 230 V model The power amplifier shall provide two channels of amplification This amplifier shall draw 650 W or less at 1 8 rated power into 4 ohm loads The power amplifier shall be capable of operation from a 230 V 50 Hz line The amplifier shall meet the following performance criteria Power output with both channels driven shall be a minimum of 1100 W per channel with a 4 ohm load 750 W with an 8 ohm load and 2200 W mono bridged into an 8 ohm load Burst peak output with both channels driven shall be a minimum of 1600 W per channel with a 2 ohm load Total harmonic distortion THD N shall be less than 0 1 at 20 Hz 20 kHz half power Intermodulation distortion IMD shall be less than 0 1 using the SMPTE standard of 60 Hz and 7 kHz in a 4 1 ratio respectively with an 8 ohm load Frequency response shall be from 20 Hz to 50 kHz 0 dB 1 dB a
6. W per channel with a 4 ohm load 275 W with an 8 ohm load and 780 W mono bridged into an 8 ohm load Burst peak output with both channels driven shall be a minimum of 650 W per channel with a 2 ohm load Total harmonic distortion THD N shall be less than 0 1 at 20 Hz 20 kHz half power Intermodulation distortion IMD shall be less than 0 1 using the SMPTE standard of 60 Hz and 7 kHz in a 4 1 ratio respectively with an 8 ohm load Frequency response shall be from 20 Hz to 50 kHz 0 dB 1 dB at 8 ohm Po 1 W Residual noise at 20 Hz 20 kHz shall be less than 70 dBu Input shall be electronically balanced with a minimum impedance of 20 kohm balanced and 10 kohm unbalanced The voltage gain shall be switched to 32 dB 26 dB 4 dBu and the input sensitivity also shall be switched to 4 dBu 9 2 dBu 3 2 dBu Maximum input voltage shall be 22 dBu The unweighted signal to noise ratio over the range of 20 Hz 20 kHz shall exceed 100 dB referenced to full output Built in protection circuitry shall monitor voltage and current levels to minimize potential damage from overloads and disable output during shorts DC offset or excessive operating temperatures 130 C The relay shall also delay amplifier connection to the load during turn on for three seconds while the protection circuitry analyzes the load In rush current limiting shall minimize turn on current surges when multiple units are powered up remotely to prevent AC breaker overload The amplifier s
7. YAMAHA 2 I XP Series ARCHITECTS amp ENGINEERS SPECIFICATIONS Power Amplifier XP7000 gt 120 V model The power amplifier shall provide two channels of amplification This amplifier shall draw 650 W or less at 1 8 rated power into 4 ohm loads The power amplifier shall be capable of operation from a 120 V 60 Hz line The amplifier shall meet the following performance criteria Power output with both channels driven shall be a minimum of 1100 W per channel with a 4 ohm load 750 W with an 8 ohm load and 2200 W mono bridged into an 8 ohm load Burst peak output with both channels driven shall be a minimum of 1600 W per channel with a 2 ohm load Total harmonic distortion THD N shall be less than 0 1 at 20 Hz 20 kHz half power Intermodulation distortion IMD shall be less than 0 1 using the SMPTE standard of 60 Hz and 7 kHz in a 4 1 ratio respectively with an 8 ohm load Frequency response shall be from 20 Hz to 50 kHz 0 dB 1 dB at 8 ohm Po 1 W Residual noise at 20 Hz 20 kHz shall be less than 70 dBu Input shall be electronically balanced with a minimum impedance of 20 kohm balanced and 10 kohm unbalanced The voltage gain shall be switched to 32 dB 26 dB 4 dBu and the input sensitivity also shall be switched to 4 dBu 13 7 dBu 7 7 dBu Maximum input voltage shall be 22 dBu The unweighted signal to noise ratio over the range of 20 Hz 20 kHz shall exceed 104 dB referenced to full output Built in protection circui
8. ach channel s level shall be independently adjustable The rear panel shall have 12 dB oct HPF switch fc 20 Hz or 55 Hz Rear panel input connectors shall be a 3 pin detachable terminal block and a 3 pin XLR connector for each channel The XLR input shall be wired with pin 2 hot Rear panel output connectors shall be a 5 way binding posts and SPEAKON connectors Dsub15P Data Port connectors shall allow remote control and monitoring The amplifier shall employ patented EEEngine technology Including MOSFET based independent high speed current and voltage buffers without delay circuits to improve slew rate Isolation components shall be provided and output devices shall be mounted by individual screws to minimize sonic degradation caused by vibration The amplifier shall conform to the latest EU RoHS hazardous substances and WEEE directives The amplifier shall have front panel carrying handles It shall use only two standard rack spaces and its dimensions shall be 480 mm W x 456 mm D x 88 mm H Weight shall be 14 kg The amplifier shall be YAMAHA XP7000 YAMAHA CORPORATION 10 1 Nakazawa cho Naka ku Hamamatsu Japan www yamahaproaudio com YAMAHA 2 I XP Series ARCHITECTS amp ENGINEERS SPECIFICATIONS Power Amplifier XP5000 gt 120 V model The power amplifier shall provide two channels of amplification This amplifier shall draw 500 W or less at 1 8 rated power into 4 ohm loads The power amplifier shall be capable of operation fro
9. ay binding posts and SPEAKON connectors Dsub15P Data Port connectors shall allow remote control and monitoring The amplifier shall employ patented EEEngine technology Including MOSFET based independent high speed current and voltage buffers without delay circuits to improve slew rate Isolation components shall be provided and output devices shall be mounted by individual screws to minimize sonic degradation caused by vibration The amplifier shall conform to the latest EU RoHS hazardous substances and WEEE directives The amplifier shall have front panel carrying handles It shall use only two standard rack spaces and its dimensions shall be 480 mm W x 456 mm D x 88 mm H Weight shall be 14 kg The amplifier shall be YAMAHA XP5000 YAMAHA CORPORATION 10 1 Nakazawa cho Naka ku Hamamatsu Japan www yamahaproaudio com YAMAHA 2 I XP Series ARCHITECTS amp ENGINEERS SPECIFICATIONS Power Amplifier XP3500 gt 120 V model The power amplifier shall provide two channels of amplification This amplifier shall draw 450 W or less at 1 8 rated power into 4 ohm loads The power amplifier shall be capable of operation from a 120 V 60 Hz line The amplifier shall meet the following performance criteria Power output with both channels driven shall be a minimum of 590 W per channel with a 4 ohm load 390 W with an 8 ohm load and 1180 W mono bridged into an 8 ohm load Burst peak output with both channels driven shall be a minimum of 1000 W pe
10. be less than 0 1 using the SMPTE standard of 60 Hz and 7 kHz in a 4 1 ratio respectively with an 8 ohm load Frequency response shall be from 20 Hz to 50 kHz 0 dB 1 dB at 8 ohm Po 1 W Residual noise at 20 Hz 20 kHz shall be less than 70 dBu Input shall be electronically balanced with a minimum impedance of 20 kohm balanced and 10 kohm unbalanced The voltage gain shall be switched to 32 dB 26 dB 4 dBu and the input sensitivity also shall be switched to 4 dBu 5 2 dBu 0 8 dBu Maximum input voltage shall be 22 dBu The unweighted signal to noise ratio over the range of 20 Hz 20 kHz shall exceed 96 dB referenced to full output Built in protection circuitry shall monitor voltage and current levels to minimize potential damage from overloads and disable output during shorts DC offset or excessive operating temperatures 130 C The relay shall also delay amplifier connection to the load during turn on for three seconds while the protection circuitry analyzes the load In rush current limiting shall minimize turn on current surges when multiple units are powered up remotely to prevent AC breaker overload The amplifier shall employ forced air cooling with dual temperature controlled fans variable in speed for minimum acoustic noise Air flow shall be from front to rear The front panel shall have a recessed AC power switch LED indicator The LED indicators shall indicate POWER STAND BY PROTECTION TEMP and REMOTE condition The front panel shal
11. binding posts and SPEAKON connectors Dsub15P Data Port connectors shall allow remote control and monitoring The amplifier shall employ patented EEEngine technology Including MOSFET based independent high speed current and voltage buffers without delay circuits to improve slew rate Isolation components shall be provided and output devices shall be mounted by individual screws to minimize sonic degradation caused by vibration The amplifier shall conform to the latest EU RoHS hazardous substances and WEEE directives The amplifier shall have front panel carrying handles It shall use only two standard rack spaces and its dimensions shall be 480 mm W x 456 mm D x 88 mm H 18 7 8 x 17 15 16 x 3 7 16 Weight shall be 12 kg 26 5 lbs The amplifier shall be YAMAHA XP1000 gt 230 V model The power amplifier shall provide two channels of amplification This amplifier shall draw 170 W or less at 1 8 rated power into 4 ohm loads The power amplifier shall be capable of operation from a 230 V 50 Hz line The amplifier shall meet the following performance criteria Power output with both channels driven shall be a minimum of 155 W per channel with a 4 ohm load 125 W with an 8 ohm load and 310 W mono bridged into an 8 ohm load Burst peak output with both channels driven shall be a minimum of 250 W per channel with a 2 ohm load Total harmonic distortion THD N shall be less than 0 1 at 20 Hz 20 kHz half power Intermodulation distortion IMD shall
12. d and output devices shall be mounted by individual screws to minimize sonic degradation caused by vibration The amplifier shall conform to the latest EU RoHS hazardous substances and WEEE directives The amplifier shall have front panel carrying handles It shall use only two standard rack spaces and its dimensions shall be 480 mm W x 456 mm D x 88 mm H Weight shall be 15 kg The amplifier shall be YAMAHA XP3500 YAMAHA CORPORATION 10 1 Nakazawa cho Naka ku Hamamatsu Japan www yamahaproaudio com YAMAHA 2 I XP Series ARCHITECTS amp ENGINEERS SPECIFICATIONS Power Amplifier XP2500 gt 120 V model The power amplifier shall provide two channels of amplification This amplifier shall draw 320 W or less at 1 8 rated power into 4 ohm loads The power amplifier shall be capable of operation from a 120 V 60 Hz line The amplifier shall meet the following performance criteria Power output with both channels driven shall be a minimum of 390 W per channel with a 4 ohm load 275 W with an 8 ohm load and 780 W mono bridged into an 8 ohm load Burst peak output with both channels driven shall be a minimum of 650 W per channel with a 2 ohm load Total harmonic distortion THD N shall be less than 0 1 at 20 Hz 20 kHz half power Intermodulation distortion IMD shall be less than 0 1 using the SMPTE standard of 60 Hz and 7 kHz in a 4 1 ratio respectively with an 8 ohm load Frequency response shall be from 20 Hz to 50 kHz 0 dB 1 d
13. hall employ forced air cooling with dual temperature controlled fans variable in speed for minimum acoustic noise Air flow shall be from front to rear The front panel shall have a recessed AC power switch LED indicator The LED indicators shall indicate POWER STAND BY PROTECTION TEMP and REMOTE condition The front panel shall have two 31 step volume knobs one per ch A rear panel mode switch shall provide three modes of input operation Stereo Bridged and Parallel In Parallel input mode each channel s level shall be independently adjustable The rear panel shall have 12 dB oct HPF switch fe 20 Hz or 55 Hz Rear panel input connectors shall be a 3 pin detachable terminal block and a 3 pin XLR connector for each channel The XLR input shall be wired with pin 2 hot Rear panel output connectors shall be a 5 way binding posts and SPEAKON connectors Dsub15P Data Port connectors shall allow remote control and monitoring The amplifier shall employ patented EEEngine technology Including MOSFET based independent high speed current and voltage buffers without delay circuits to improve slew rate Isolation components shall be provided and output devices shall be mounted by individual screws to minimize sonic degradation caused by vibration The amplifier shall conform to the latest EU RoHS hazardous substances and WEEE directives The amplifier shall have front panel carrying handles It shall use only two standard rack spaces and its dimensions shall be 480 m
14. ifier shall provide two channels of amplification This amplifier shall draw 450 W or less at 1 8 rated power into 4 ohm loads The power amplifier shall be capable of operation from a 230 V 50 Hz line The amplifier shall meet the following performance criteria Power output with both channels driven shall be a minimum of 590 W per channel with a 4 ohm load 390 W with an 8 ohm load and 1180 W mono bridged into an 8 ohm load Burst peak output with both channels driven shall be a minimum of 925 W per channel with a 2 ohm load Total harmonic distortion THD N shall be less than 0 1 at 20 Hz 20 kHz half power Intermodulation distortion IMD shall be less than 0 1 using the SMPTE standard of 60 Hz and 7 kHz in a 4 1 ratio respectively with an 8 ohm load Frequency response shall be from 20 Hz to 50 kHz 0 dB 1 dB at 8 ohm Po 1 W Residual noise at 20 Hz 20 kHz shall be less than 70 dBu Input shall be electronically balanced with a minimum impedance of 20 kohm balanced and 10 kohm unbalanced The voltage gain shall be switched to 32 dB 26 dB 4 dBu and the input sensitivity also shall be switched to 4 dBu 10 7 dBu 4 7 dBu Maximum input voltage shall be 22 dBu The unweighted signal to noise ratio over the range of 20 Hz 20 kHz shall exceed 102 dB referenced to full output Built in protection circuitry shall monitor voltage and current levels to minimize potential damage from overloads and disable output during shorts DC offset or excess
15. ive operating temperatures 130 C The relay shall also delay amplifier connection to the load during turn on for three seconds while the protection circuitry analyzes the load In rush current limiting shall minimize turn on current surges when multiple units are powered up remotely to prevent AC breaker overload The amplifier shall employ forced air cooling with dual temperature controlled fans variable in speed for minimum acoustic noise Air flow shall be from front to rear The front panel shall have a recessed AC power switch LED indicator The LED indicators shall indicate POWER STAND BY PROTECTION TEMP and REMOTE condition The front panel shall have two 31 step volume knobs one per ch A rear panel mode switch shall provide three modes of input operation Stereo Bridged and Parallel In Parallel input mode each channel s level shall be independently adjustable The rear panel shall have 12 dB oct HPF switch fe 20 Hz or 55 Hz Rear panel input connectors shall be a 3 pin detachable terminal block and a 3 pin XLR connector for each channel The XLR input shall be wired with pin 2 hot Rear panel output connectors shall be a 5 way binding posts and SPEAKON connectors Dsub15P Data Port connectors shall allow remote control and monitoring The amplifier shall employ patented EEEngine technology Including MOSFET based independent high speed current and voltage buffers without delay circuits to improve slew rate Isolation components shall be provide
16. l have a recessed AC power switch LED indicator The LED indicators shall indicate POWER STAND BY PROTECTION TEMP and REMOTE condition The front panel shall have two 31 step volume knobs one per ch A rear panel mode switch shall provide three modes of input operation Stereo Bridged and Parallel In Parallel input mode each channel s level shall be independently adjustable The rear panel shall have 12 dB oct HPF switch fc 20 Hz or 55 Hz Rear panel input connectors shall be a 3 pin detachable terminal block and a 3 pin XLR connector for each channel The XLR input shall be wired with pin 2 hot Rear panel output connectors shall be a 5 way binding posts and SPEAKON connectors Dsub15P Data Port connectors shall allow remote control and monitoring The amplifier shall employ patented EEEngine technology Including MOSFET based independent high speed current and voltage buffers without delay circuits to improve slew rate Isolation components shall be provided and output devices shall be mounted by individual screws to minimize sonic degradation caused by vibration The amplifier shall conform to the latest EU RoHS hazardous substances and WEEE directives The amplifier shall have front panel carrying handles It shall use only two standard rack spaces and its dimensions shall be 480 mm W x 456 mm D x 88 mm H 18 7 8 x 17 15 16 x 3 7 16 Weight shall be 15 kg 33 1 lbs The amplifier shall be YAMAHA XP3500 gt 230 V model The power ampl
17. l have two 31 step volume knobs one per ch A rear panel mode switch shall provide three modes of input operation Stereo Bridged and Parallel In Parallel input mode each channel s level shall be independently adjustable The rear panel shall have 12dB oct HPF switch fe 20 Hz or 55 Hz Rear panel input connectors shall be a 3 pin detachable terminal block and a 3 pin XLR connector for each channel The XLR input shall be wired with pin 2 hot Rear panel output connectors shall be a 5 way binding posts and SPEAKON connectors Dsub15P Data Port connectors shall allow remote control and monitoring The amplifier shall employ patented EEEngine technology Including MOSFET based independent high speed current and voltage buffers without delay circuits to improve slew rate Isolation components shall be provided and output devices shall be mounted by individual screws to minimize sonic degradation caused by vibration The amplifier shall conform to the latest EU RoHS hazardous substances and WEEE directives The amplifier shall have front panel carrying handles It shall use only two standard rack spaces and its dimensions shall be 480 mm W x 456 mm D x 88 mm H Weight shall be 12 kg The amplifier shall be YAMAHA XP1000 YAMAHA CORPORATION 10 1 Nakazawa cho Naka ku Hamamatsu Japan www yamahaproaudio com
18. m W x 456 mm D x 88 mm H Weight shall be 14 kg The amplifier shall be YAMAHA XP2500 YAMAHA CORPORATION 10 1 Nakazawa cho Naka ku Hamamatsu Japan www yamahaproaudio com YAMAHA 2 I XP Series ARCHITECTS amp ENGINEERS SPECIFICATIONS Power Amplifier XP1000 gt 120 V model The power amplifier shall provide two channels of amplification This amplifier shall draw 170 W or less at 1 8 rated power into 4 ohm loads The power amplifier shall be capable of operation from a 120 V 60 Hz line The amplifier shall meet the following performance criteria Power output with both channels driven shall be a minimum of 165 W per channel with a 4 ohm load 135 W with an 8 ohm load and 330 W mono bridged into an 8 ohm load Burst peak output with both channels driven shall be a minimum of 250 W per channel with a 2 ohm load Total harmonic distortion THD N shall be less than 0 1 at 20 Hz 20 kHz half power Intermodulation distortion IMD shall be less than 0 1 using the SMPTE standard of 60 Hz and 7 kHz in a 4 1 ratio respectively with an 8 ohm load Frequency response shall be from 20 Hz to 50 kHz 0 dB 1 dB at 8 ohm Po 1 W Residual noise at 20 Hz 20 kHz shall be less than 70 dBu Input shall be electronically balanced with a minimum impedance of 20 kohm balanced and 10 kohm unbalanced The voltage gain shall be switched to 32 dB 26 dB 4 dBu and the input sensitivity also shall be switched to 4 dBu 5 2 dBu 0 8 dBu Maximu
19. m a 120 V 60 Hz line The amplifier shall meet the following performance criteria Power output with both channels driven shall be a minimum of 750 W per channel with a 4 ohm load 525 W with an 8 ohm load and 1500 W mono bridged into an 8 ohm load Burst peak output with both channels driven shall be a minimum of 1300 W per channel with a 2 ohm load Total harmonic distortion THD N shall be less than 0 1 at 20 Hz 20 kHz half power Intermodulation distortion IMD shall be less than 0 1 using the SMPTE standard of 60 Hz and 7 kHz in a 4 1 ratio respectively with an 8 ohm load Frequency response shall be from 20 Hz to 50 kHz 0 dB 1 dB at 8 ohm Po 1 W Residual noise at 20 Hz 20 kHz shall be less than 70 dBu Input shall be electronically balanced with a minimum impedance of 20 kohm balanced and 10 kohm unbalanced The voltage gain shall be switched to 32 dB 26 dB 4 dBu and the input sensitivity also shall be switched to 4 dBu 12 2 dBu 6 2 dBu Maximum input voltage shall be 22 dBu The unweighted signal to noise ratio over the range of 20 Hz 20 kHz shall exceed 103 dB referenced to full output Built in protection circuitry shall monitor voltage and current levels to minimize potential damage from overloads and disable output during shorts DC offset or excessive operating temperatures 100 C The relay shall also delay amplifier connection to the load during turn on for three seconds while the protection circuitry analyzes the load In
20. m input voltage shall be 22 dBu The unweighted signal to noise ratio over the range of 20 Hz 20 kHz shall exceed 96 dB referenced to full output Built in protection circuitry shall monitor voltage and current levels to minimize potential damage from overloads and disable output during shorts DC offset or excessive operating temperatures 130 C The relay shall also delay amplifier connection to the load during turn on for three seconds while the protection circuitry analyzes the load In rush current limiting shall minimize turn on current surges when multiple units are powered up remotely to prevent AC breaker overload The amplifier shall employ forced air cooling with dual temperature controlled fans variable in speed for minimum acoustic noise Air flow shall be from front to rear The front panel shall have a recessed AC power switch LED indicator The LED indicators shall indicate POWER STAND BY PROTECTION TEMP and REMOTE condition The front panel shall have two 31 step volume knobs one per ch A rear panel mode switch shall provide three modes of input operation Stereo Bridged and Parallel In Parallel input mode each channel s level shall be independently adjustable The rear panel shall have 12dB oct HPF switch fe 20 Hz or 55 Hz Rear panel input connectors shall be a 3 pin detachable terminal block and a 3 pin XLR connector for each channel The XLR input shall be wired with pin 2 hot Rear panel output connectors shall be a 5 way
21. r channel with a 2 ohm load Total harmonic distortion THD N shall be less than 0 1 at 20 Hz 20 kHz half power Intermodulation distortion IMD shall be less than 0 1 using the SMPTE standard of 60 Hz and 7 kHz in a 4 1 ratio respectively with an 8 ohm load Frequency response shall be from 20 Hz to 50 kHz 0 dB 1 dB at 8 ohm Po 1 W Residual noise at 20 Hz 20 kHz shall be less than 70 dBu Input shall be electronically balanced with a minimum impedance of 20 kohm balanced and 10 kohm unbalanced The voltage gain shall be switched to 32 dB 26 dB 4 dBu and the input sensitivity also shall be switched to 4 dBu 10 7 dBu 4 7 dBu Maximum input voltage shall be 22 dBu The unweighted signal to noise ratio over the range of 20 Hz 20 kHz shall exceed 102 dB referenced to full output Built in protection circuitry shall monitor voltage and current levels to minimize potential damage from overloads and disable output during shorts DC offset or excessive operating temperatures 130 C The relay shall also delay amplifier connection to the load during turn on for three seconds while the protection circuitry analyzes the load In rush current limiting shall minimize turn on current surges when multiple units are powered up remotely to prevent AC breaker overload The amplifier shall employ forced air cooling with dual temperature controlled fans variable in speed for minimum acoustic noise Air flow shall be from front to rear The front panel shal
22. t 8 ohm Po 1 W Residual noise at 20 Hz 20 kHz shall be less than 70 dBu Input shall be electronically balanced with a minimum impedance of 20 kohm balanced and 10 kohm unbalanced The voltage gain shall be switched to 32 dB 26 dB 4 dBu and the input sensitivity also shall be switched to 4 dBu 13 7 dBu 7 7 dBu Maximum input voltage shall be 22 dBu The unweighted signal to noise ratio over the range of 20 Hz 20 kHz shall exceed 104 dB referenced to full output Built in protection circuitry shall monitor voltage and current levels to minimize potential damage from overloads and disable output during shorts DC offset or excessive operating temperatures 100 C The relay shall also delay amplifier connection to the load during turn on for three seconds while the protection circuitry analyzes the load In rush current limiting shall minimize turn on current surges when multiple units are powered up remotely to prevent AC breaker overload The amplifier shall employ forced air cooling with dual temperature controlled fans variable in speed for minimum acoustic noise Air flow shall be from front to rear The front panel shall have a recessed AC power switch LED indicator The LED indicators shall indicate POWER STAND BY PROTECTION TEMP and REMOTE condition The front panel shall have two 31 step volume knobs one per ch A rear panel mode switch shall provide three modes of input operation Stereo Bridged and Parallel In Parallel input mode e
23. try shall monitor voltage and current levels to minimize potential damage from overloads and disable output during shorts DC offset or excessive operating temperatures 100 C The relay shall also delay amplifier connection to the load during turn on for three seconds while the protection circuitry analyzes the load In rush current limiting shall minimize turn on current surges when multiple units are powered up remotely to prevent AC breaker overload The amplifier shall employ forced air cooling with dual temperature controlled fans variable in speed for minimum acoustic noise Air flow shall be from front to rear The front panel shall have a recessed AC power switch LED indicator The LED indicators shall indicate POWER STAND BY PROTECTION TEMP and REMOTE condition The front panel shall have two 31 step volume knobs one per ch A rear panel mode switch shall provide three modes of input operation Stereo Bridged and Parallel In Parallel input mode each channel s level shall be independently adjustable The rear panel shall have 12 dB oct HPF switch fc 20 Hz or 55 Hz Rear panel input connectors shall be a 3 pin detachable terminal block and a 3 pin XLR connector for each channel The XLR input shall be wired with pin 2 hot Rear panel output connectors shall be a 5 way binding posts and SPEAKON connectors Dsub15P Data Port connectors shall allow remote control and monitoring The amplifier shall employ patented EEEngine technology Including MOS
24. ximum input voltage shall be 22 dBu The unweighted signal to noise ratio over the range of 20 Hz 20 kHz shall exceed 103 dB referenced to full output Built in protection circuitry shall monitor voltage and current levels to minimize potential damage from overloads and disable output during shorts DC offset or excessive operating temperatures 100 C The relay shall also delay amplifier connection to the load during turn on for three seconds while the protection circuitry analyzes the load In rush current limiting shall minimize turn on current surges when multiple units are powered up remotely to prevent AC breaker overload The amplifier shall employ forced air cooling with dual temperature controlled fans variable in speed for minimum acoustic noise Air flow shall be from front to rear The front panel shall have a recessed AC power switch LED indicator The LED indicators shall indicate POWER STAND BY PROTECTION TEMP and REMOTE condition The front panel shall have two 31 step volume knobs one per ch A rear panel mode switch shall provide three modes of input operation Stereo Bridged and Parallel In Parallel input mode each channel s level shall be independently adjustable The rear panel shall have 12 dB oct HPF switch fe 20 Hz or 55 Hz Rear panel input connectors shall be a 3 pin detachable terminal block and a 3 pin XLR connector for each channel The XLR input shall be wired with pin 2 hot Rear panel output connectors shall be a 5 w
Download Pdf Manuals
Related Search