Xantech Universal Remote 490-95 User's Manual
Contents
1. break out block In Figure 4 a 490 95 is extended down to a 789 44 Connecting Block and combined with other Xantech IR Receivers 1 2 3 Plug the 3 5mm stereo mini plug from the 490 95 into the IR RCVR input on the CB12 Connecting Block Using 3 Conductor wire refer to Specifications section for proper Wire Gauge connect the terminals labeled V G S of the CB12 to the terminals labeled 12VDC GND and IR IN on the 789 44 Connecting Block or other Plug in the 2 1mm Coaxial power plug of the 781RG or 782 Power Supply not included into the jack labeled PWR on the 789 44CB CAUTION Do not plug in a 781RG or any other Power Supply into the CB12 when using in a break out configuration This will put 2 supplies in parallel and possibly damage your equipment If a local emitter is needed on the CB12 see Step 5 below 4 Plug in the Emitters 3 5mm mono mini plug such as any of the 282 284 283 and 286 series into the Emitter Outputs on the 789 44 2004 Xantech Corporation Page 4 Model 490 95 ROOM 2 ROOM 3 490 95 3 Wire Plasma Friendly M 12V Pa Cable IR Receiver 480 00 Dinky Link Hand Held Remote Ey gt 780 10 1S k X red IR Receiver Fa Text IR Reconice IR OUT Stripe INO UMd C1 ooanertna loc ACF T 120 vac Satellite Receiver unswitched gt a5 782 002. e Small size mounts in 4 diameter hole 2 inches deep 70mm e Quick Connect 3 5mm Stereo Mini Plug on 7ft 213 36cm cable for direct plug in to Xantech Connecting Blocks Works in normal 3 wire mode 12VDC IR GND Green Talkback LED for System Verification Improved Fluorescent Light rejection under most conditions and rejection from LCD Displays Can be used in Direct Sunlight RF Grid included for EMI interference reduction Includes CB12 Connecting Block for easy connection and extension of 7 ribbon cable 7 units may be powered by one 781RG power supply Note The 490 95 will not operate in 2 wire Phantom Power mode SPECIFICATIONS e Infrared modulation frequency bandwidth 30 100 kHz e Reception range up to 55 feet 17M depending on local conditions e Reception angle 55 degrees off axis for 50 range reduction e Cable requirements 3 conductor Use 24 gauge up to 200 61M 22 gauge up to 600 182 5M 20 gauge up to 1000 305M 18 gauge up to 2000 610KM unshielded OK Maximum transmission length One mile using 18 gauge wire 1 6KM Maximum current output 100 mA Dimensions 0 75 diameter x 2 75 deep 19mm x 70mm Power requirements 12 volts DC 20 mA Page 2 Model 490 95 INSTALLATION These units equipped with a 7 foot cable and 3 5 mm stereo mini plug are intended to be plugged directly into the IR RCVR or AUX jack on Xantech Connecting Blocks such as the CB12 included CB60 789 44 7
3. i 3 I lt Power z Supply eS Mouse Emitter 789 44 VCR Connecting Block sl ee 282M Emitter AV Receiver i 283M Blink IR Emitter 286M Dual Blink IRs Z to other 7 controlled devices 3 Conductor Room to Room Cable 24 to 18 gauge unshielded OK IR Receiver gt Figure 4 Advanced Wiring Configuration using 490 95 CB12 789 44 781RG and multiple 286M s 291 10 i 5 If alocal Emitter is needed on the CB12 you will need to place a 470 Ohm Resistor in Series with the Signal Output on the CB12 To Wire in this fashion a Cut a standard Mouse Emitter 282M or 283M approximately 12inches from the 3 5mm Mono Mini Jack You will now have 2 cables one with a 3 5mm Mono Mini Jack and one with the Mouse Emitter b Wire the 2 leads of the Mono Mini Jack side to a terminal Strip c On the Terminal Strip opposite the lead with the White Stripe Signal connect one side of the 470 Ohm Resistor d Wire the other side of the resistor to the lead with the White Stripe on the Mouse Emitter e Connect the Black Wire of the Mouse Emitter to the Terminal Strip opposite the Black Wire GND from the 3 5mm Mono Mini Jack This will keep the proper load balance and prevent miscommunication with the Emitters on the 789 44 CB 3 5MM MINI PLUG PINOUT There might be times when the 490 95 needs to be wired directly to a Terminal Block In that case you will need to cut off the 3 5mm jack and wire acco
4. 91 44 etc The 490 95 should be used in installations where the connecting block is within reach of the 7 foot cable such as when installing the 490 95 in a cabinet where the controlled equipment is behind closed doors PLACEMENT Placement of the IR Receiver does matter when used in the presence of a Plasma Display Ideally it should be placed at areas around the Display with the front of the receiver flush with the front of or set back from the Display If the 490 95 needs to be placed in front of the display such as on an adjacent side wall perpendicular to the display make sure it is placed at a location at least 45 degrees off axis from the corners of the unit see Figure 1 The presence of Direct Sunlight and Fluorescent Lighting should not effect the reception of this unit Figure 1 490 95 Placement wr Te a a a R Note Plasma interference can be reflected off of any item it comes into contact with within approx 3 ft from the front of the display Keeping this in mind make sure that the 490 95 is free of any obstruction that might reflect back into the receiving eye Note While this unit shows strong rejection to standard 50 60Hz ballasted fluorescent lighting it is still prone to interference from CFL style Fluorescent lighting MOUNTING 1 Drill a 0 75 19mm hole in any flat surface such as a cabinet panel 2 Pass the lead and the body of the 490 95 through the hole 3 Sec
5. INSTALLATION INSTRUCTIONS MODEL 490 95 MICRO LINK PLASMA FRIENDLY INFRARED RECEIVER TABLE OF CONTENTS INTRODUCTION ercenss sectac ct bites statttas oh otetas a is SR Ue eee Sue Eee coo Stak Sante chubtta Garena Pabenas Gar anae ous 1 Feature Saa has Shh cet e tice ube abt att ata ue ati dat ule alt iat tule lt il aE alia et lid edi ital tala tet act tenant ater ucnaaue 1 SPECI CAL ONS 3 8 a cc Sach ck ecw Sac ac Sec cae cece we weve E ON 1 INSTALEATION ss as oe ee a see se 2 PAGO eee esse ee ee ee 2 IMOUIMUITIG tctctacahn cRtchntonahc E tol obhteMateRhl cLol E A ci orcas E clot cbi eB NEsUM toh chal shat ehal halal shot oy 2 FADPIICAU OM VVINIMIG A actennte hat horc tats het ohol Moke babs hots ints Dancin Lolst st chat E A Lobe tal chats bob A A AE A cithc hate And chal hat hala hot gy 3 Advanced Wiring Configuration cccccceccceceeeeeeecceneeeeeeeeeeeeecnaeeeeeeeeeeeeecaaeeeeeeeeceeccccaeeeeeeeeeeeccccaeeeeeeeeeesessccieeeeeeeeetees 3 SOM MIP PUG IOUT TTT 4 INTRODUCTION The 490 95 is designed to reject interference from Plasma Displays from entering the IR signal line These Small IR Receivers are intended to be mounted in panels doors cabinets etc for control of A V equipment behind closed doors or any IR Repeater System that is in close proximity of a Plasma or LCD Displays Modeled after the original 490 90 the 490 95 offers the same features as its predecessor but in a smaller mounting frame FEATURES
6. rding to Table 1 Table 1 490 95 Connector Pin Out PLUG CABLE LEADS CIRCUIT ITEM TIP WHITE IR OUT RING GROUND SLEEVE CAUTION With any of these systems be sure the 781 RG Power Supply is plugged into an un switched AC outlet This maintains the 490 system in stand by operation so that power on commands can be sent to the controlled equipment XANTECH CORPORATION 13100 Telfair Avenue Sylmar CA 91342 3829 phone 818 362 0353 fax 818 362 9506 Part No 08901485 Rev A 07 22 04 2004 Xantech Corporation
7. ure from the rear with the Washer and Nut all supplied as shown in Figure 2a Be sure not to over tighten nut Figure 2a 490 95 Features Figure 2b 490 95 Dimensions 2004 Xantech Corporation Model 490 95 Page 3 APPLICATION WIRING A typical system with a 490 95 781RG Power Supply and 283M Emitter plugged into a 789 44 Connecting Block is shown in Figure 3 1 2 3 4 Plug in the 2 1mm Coaxial power plug of the 781RG Power Supply not included into the jack labeled 12VDC on the 789 44 Connecting Block Plug the AC end of the 781RG power Supply into an un switched 120v AC Line outlet Plug the 3 5mm stereo mini plug from the 490 95 into the IR RCVR input on the 789 44 Connecting Block Plug in the Emitters 3 5mm mono mini plug such as any of the 282 284 283 and 286 series into the jacks labeled EMITTERS on the 789 44 and affix the opposite end to the IR Sensor Window of the controlled equipment 781RG Power Supply Satellite Receiver unswitched 283M Emitter 490 95 789 44 o Link Connecting Block Plasma Friendly IR Receiver Hand Held ac Remote 8 Ba a LEP NY ga E z a g L A 283M Blink IR Mouse Emitter Equipment Rack Figure 3 Typical System Layout using 490 95 789 44 781RG and 283M Emitters ADVANCED WIRING CONFIGURATION 490 95 may also be used where the 7 foot lead is not long enough In this case simply use the CB12 Connecting Block as a
Download Pdf Manuals
Related Search