Xantech 283DPRO User's Manual
Contents
1. 3DPRO visible emitter will also indicate the presence of stray IR or RF interference by randomly blinking when no IR control signal is being sent Reposition the IR receiver of the interfering source to eliminate or reduce the random blinking The more the random blinking is reduced the better the system will function ERGPS Salita Receiver To 120 VAC IR amp s Unsewitched Window ist m Emitter 789 44 Connecting Block ovo E gt Emitter EEE i i ti m AW Riecerver al Ci agag Sjan gS 588880 Emitter EQUIPMENT CABINET CLOSET ETC 2910 SERIES IA Receiver Hand Held w Pemote Limited Warranty Xantech warrants its products to be free of defects in materials or workmanship This is a Limited Lifetime warranty from the date of purchase by the original consumer Any products returned to Xantech and found to be defective by Xantech within the warranty period will be repaired or replaced at Xantech s option at no charge Xantech will not be responsible for the actual cost of installation or removal of the product nor for any incidental or consequential damages Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation may not apply to you This warranty gives you specific legal rights You may have additional legal rights that vary from state to state Xantech Corporation 13100 Telfair Ave 2F Sylmar CA 91342 X2. antech com Installation Instructions 283DPRO 2008 Xantech Corporation Document 08905199X1 This document is copyright protected No part of this manual may be copied or reproduced in any form without prior written consent from Xantech Corporation Xantech Corporation shall not be liable for operational technical or editorial errors omissions made in this document
3. lied Pee a e In some cases it may be difficult to find the location of the IR sensor on the component Consult the owner s manual of the unit or the manufacturer for the exact IR sensor window location e Double sided adhesive tape is included If you move the emitter to a different component use this tape to replace the current adhesive layer for the best adhesion e The shell though dark in appearance is transparent to infrared light allowing commands from a handheld remote control to pass through it This permits direct control of the equipment from a handheld remote as well as from the 283DPRO BLACK IR OPAQUE EMITTER SHIELD An optional shield available from Xantech as model 28DES fits over the emitter head and the sensor window of the controlled component It prevents unwanted external IR signals from passing through or leaking past it A Adhesive Layer Controlled Component Top View Emitter Shield and Emitter installed Side View over IR sensor window Use the 28DES when you want the equipment to respond only to the 283DPRO such as in zone controlled systems CONNECTING THE EMITTERS e Simply insert the mono mini plug of the 283DPRO emitter into the EMITTERS or OUT jacks on any of the Xantech Connecting Blocks or Controllers e CAUTION DO NOT plug emitters into the IN OUT or HIGH OUT jacks on the 790 00 and 791 44 Connecting Blocks To do so will destroy the emitters e The 28
4. xantecn MODEL 283DPRO Professional Visible Emitter INSTALLATION INSTRUCTIONS ONNA277CNS1565M9 DESCRIPTION The 283DPRO Professional Visible Emitter is a two piece Emitter Featuring a Designer Emitter the head end piece can be attached to any electronic component such as a DVD player With dressed cables using the included adhesive cable channels an Emitter can now become part of the electronic equipment The secondary section connects the Designer Emitter to a Xantech IR system Additional lengths for the secondary section are available in the 283DPROKIT The 283DPRO eliminates cabling confusion and turns the most complex installation into a professional installation INSTALLATION HEAD END DESIGNER EMITTER Side View 1 4 Top View j 2 FT 15 8 3 5mm female cable connector SECONDARY CABLE LENGTH 6 FEET 3 5mm mono 3 5mm mono mini plug mini plug ee ae A LENGTH r ATTACHING THE EMITTERS TO IR SENSOR WINDOWS e Each emitter has a clear adhesive layer on the bottom flat surface of the shell e Simply peel off the adhesive cover and affix the emitter to the center of the IR sensor window on the controlled component s front panel IR amp Red Light a _ Output i at IR amp Red a Light Output_ On TTD Compound Side Emitter she Clear adhesive layer place if necessaly with a short piece of th 1e 2 sided tape supp
Download Pdf Manuals
Related Search