Woodstock D3038 User's Manual
Contents
1. to provide direct line of sight between remote and receiver Turn ON remote control transmitter Turn ON dust collector Allow unit to cool then press the button on the bottom of the receiver unit to reset breaker Reset wall circuit breaker Check that breaker is in good condition and circuit is properly sized for the dust collector in use Replace weak dead battery Only use this unit on machines with standard ON OFF toggle switches Refer to dust collector manufacturer s documentation for troubleshooting Check use second remote Replace unit2. Model D3038 REMOTE DUST COLLECTOR SWITCH Instruction Sheet Introduction The Model D3038 Remote Dust Collector Switch Figure 1 allows the operator to turn the dust collector ON OFF from a distance of up to 75 feet Read and understand this entire document before installation to make sure the Model D3038 fits the intended application 4 CAUTION Only connect the Model D3038 to a 110V circuit with a NEMA 5 15 receptacle DO NOT connect a dust collec tor with a motor larger than 11 2 HP Failure to follow these warnings will void the warranty and could cause damage to the remote switch and the dust collector NOTICE This switch is designed to be used only on dust collectors with standard ON OFF toggle switches Due to the nature of magnetic switches the Model D3038 WILL NOT function properly if connected to a machine with this type of switch If you are uncertain about the type of switch on your dust collector contact the manufacturer for more information Do not attempt to bypass the dust collector switch with this unit Use of the Model D3038 for applications other than dust collectors may cause the unit to fail and will void the warranty The remote control transmitters and receiver included in this package are programmed specifically for each other For this reason replacement transmitters are not available for purchase If both transmitters are lost or damaged an entire new unit must be purchased Fi
3. e receiver unit onto the mounting bracket Bracket 4 Plug the receiver power cord into a 5 15 receptacle then plug the dust collector cord into the receiver 110V GROUNDED unit 5 15 RECEPTACLE NOTICE Only connect the Model D3038 to a 110V circuit with a NEMA 5 15 receptacle DO NOT connect a dust collec 5 15 PLUG Neutral Hot tor with a motor larger than 11 2 HP Failure to follow these warnings will void the warranty and could cause damage to the remote switch and the dust collector Figure 4 NEMA 5 15 plug amp receptacle 5 If the batteries are not installed in the remote A CAUTION control transmitters install them as described on DO NOT modify the provided plug or rego use an adapter if the plug will not fit your receptacle This is an indication that your power supply circuit does NOT meet the requirements for the machine have an electrician install the correct power supply circuit If the machine must be reconnected for use on a different type of electric circuit the reconnection should be made by a qualified electrician or service personnel after reconnection the machine must comply with all local codes and ordinances D3038 Remote Dust Collector Switch 6 Turn the remote control transmitters ON with the ON OFF switch shown in Figure 5 The LED indicators will light to show the transmitters are working If the LEDs don t light remove the protective covering from the batteries S
4. ee Replacing Batteries below to access the batteries Note To conserve battery life in the remote control transmitters only turn them on when they are needed for use 7 Turn the switch on the dust collector unit to the ON position Test the function of the remote dust collector switch by pressing the ON and OFF buttons on each remote Replacing Batteries 1 Remove the two screws from the back of the remote control transmitter 2 Remove the back of the remote control transmitter as shown in Figure 6 3 Remove the existing battery then install a new 9V battery 4 Replace the back of the remote transmitter and secure it with the two screws removed in Step 1 Tip During long term storage remove the batteries from the remote control transmitters to prevent damage from battery leakage or corrosion Troubleshooting PROBLEM POSSIBLE CAUSE Unit will not turn on Remote is out of range 2 Signal is obstructed Remote is not turned ON Dust collector is turned OFF Receiver circuit breaker has tripped Wall circuit breaker has tripped Remote battery is weak dead Connected to a machine with a magnetic switch Dust collector is at fault Remote control transmitter is at fault Receiver unit is at fault ON OFF Switch Figure 5 ON OFF Switch location Figure 6 Battery installation replacement CORRECTIVE ACTION Move remote closer to receiver unit Remove obstructions
5. gure 1 Model D3038 Specifications WOVEAOG s c2onceneeesorenctceestavestes 110V Only Max Current cccccescceecceecs 15A Peak Receiver Range scceeceeceees 75 Feet Control Signal aesscsecotaucewnceseecees Infrared Plug Receptacle Type eeecees 5 15 Inventory Figure 2 Qty A Receiver Unit cccceccesccecces 1 B Remote Control Transmitters 2 C Tap Screws sesssessesssesooesoessseeoee 2 D Mounting Bracket ssssssscsseesee 1 Figure 2 Inventory COPYRIGHT JANUARY 2011 BY WOODSTOCK INTERNATIONAL ING WARNING NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT 13756JB THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL ING Printed in China ODSTO Sa SHOP FOX D3038 Remote Dust Collector Switch Installation 1 Identify a mounting location for the receiver unit that allows the power cord to reach an appropriate outlet and the dust collector power to be plugged into the receiver outlet Note You may choose to attach the receiver unit directly to your dust collector If so mount it to a portion of the frame that will not compromise the function or strength of the dust collector Reciever Unit 2 Attach the mounting bracket in the chosen location using the included screws as shown in Figure 3 If you are mounting the bracket to the dust collector frame you may have to use alternative mounting hardware Mounting 3 Hook th
Download Pdf Manuals
Related Search