Woods Equipment MOUNTING KIT 211716 User's Manual
Contents
1. 64062 M16 x 2 0P x 40 mm HHCS CD6860 1 Figure 3 Rear Mount Installation Maloate wa bdil Mount Installation 5 Install Right and Left Front Mounts 1 Install right 4 and left front mounts 5 to front of tractor using eight four per side cap screws 7 flat washers 10 and hex nuts 8 Position cap screws on the outside of mount with flat washers and hex nuts on the inside of tractor frame 4 1034180 Right front mount 5 1034181 Left front mount 7 307301 M12 x 1 75P x 40 mm HHCS 8 307813 M12 x 1 75 Hex nut 10 57816 1 2 Hardened flat washer Figure 4 Front Mount Installation Install Side Rails 1 CD6860 3 Attach front end of right side rail 3 to outside of front mount 4 Secure with two carriage bolts 9 flat washers 11 and hex nuts 6 Attach side rails to the inside between tractor and mount of right rear mount 1 using three carriage bolts 9 flat washers 11 and hex nuts 6 Repeat steps for installation of left side rail Figure 5 Right Side Rail Installation 1 1019010 3 1019013 4 1019018 6 230 9 5607 11 57817 Right rear mount Side rail Right front mount 5 8 Hex nut 5 8 NC x 1 1 2 Carriage bolt 5 8 Hardened flat washer kat ata ae Sa 6 Mount Installation Rev 9 29 2011 MAN0426 3 3 2006 Torque Hardware Torque all mounting hardware to specifications given below TORQU2. all hydrau lic hoses within 20 inches of the operator and be secured onto metal hose fittings Replace hoses or sleeves if damaged or if protective sleeve cannot be properly positioned or secured H Make sure all hydraulic hoses fittings and valves are in good condition and not leaking before starting power unit or using equipment Check and route hoses carefully to prevent damage Hoses must not be twisted bent sharply kinked frayed pinched or come into contact with any moving parts Operate moveable components through full operational range to check clearances Replace any damaged hoses immediately E Always wear relatively tight and belted clothing to avoid getting caught in moving parts Wear sturdy rough soled work shoes and protective equipment for eyes hair hands hearing and head and respirator or filter mask where appropriate H Do not modify or alter or permit anyone else to modify or alter the equipment or any of its compo nents in any way H Do not allow bystanders in the area when oper ating attaching removing assembling or servic ing equipment H Use a suitable lifting device of sufficient capac ity Use adequate personnel to handle heavy com ponents H Keep all persons away from operator control area while performing adjustments service or maintenance Loader Mounting Kit SR3 11 1 2002 211716 LOADER MOUNTING KIT Tractor Preparation A WARNING m Only use 211716 Loade
3. osnon British Standard Pipe Parallel NPSM oscene National Pipe Straight Mechanical BSPTM British Standard Pipe Tapered Male NET a a n deh a e kok ekta n a National Pipe Tapered OM ka ot na see kk kote eske ba Constant Velocity NPT SWF National Pipe Tapered Swivel Female COW iii oo ianea inva Counter Clockwise ORBM 505580 dhas a osepis yi sekans cee O Ring Boss Male GW s kdk pp koi dey abo de post oo kis asyo kodase eas Clockwise Fen danti pann n retan Deka dead e edi ete ke kk kan iran e kenn cae Pitch a ak a a kk a kk kk weet Female PBY hirrrrrreeerrrererssrnrrrsasssssonsssoonnonen POWOP BOEYONA GA esse vo cite dis kavo koi anne dy Gauge a E E TT Pounds per Square Inch GR 5 610 Jia Grade 5 etc PTO conda n Power Take Off AACS iiss eet Hex Head Cap Screw Dener eee terre renee ere Quick Disconnect FAT e av E kai klan v sete ed bkkaan Heat Treated FA a e ti a n E pk e ka a AA Right Hand Joint Industry Council 37 Degree Flare ROP Siniseen Roll Over Protective Structure LA ina E EE po T E oe Left Hand RPM reire ani E Revolutions Per Minute KEN E AA ETE E T Left FT At E AO E RA eka da ian Ri p Right I ek kk a wk n on ka ek oi a e pak on ts Meter SAB spagan Society of Automotive Engineers MUM ke kle ee ep oak bk keep ei an e Millimeter UN Gato ave onon sd pa en pat ene Unified Coarse A bi ka tek ka b ei nen A koka pie ated eee Male UNE gita cece ones a oi pon a ot pata ot pon aime pani an Unified Fine MPa pie d
4. 0426 3 3 2006 P ar t S 1 1 application BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific Fasteners must always be replaced with the same grade as specified in the manual parts list Always use the proper tool for tightening hardware SAE for SAE hardware and Metric for metric hardware Make sure fastener threads are clean and you start thread engagement properly All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 8 J1701M JUL 96 Y SAE SERIES SAE Bolt Head CM A TORQUE Identification A CHART SAE Grade 2 SAE Grade 5 SAE Grade 8 No Dashes 3 Radial Dashes 6 Radial Dashes A MARKING ON HEAD Diameter Wrench SAE 2 SAE 5 SAE 8 Inches Size lbs ft N m Ibs ft N m lbs ft N m 1 4 7 16 6 8 10 13 14 18 5 16 1 2 12 17 19 26 27 37 3 8 9 16 23 31 35 47 49 67 7 16 5 8 36 48 55 75 78 106 1 2 3 4 55 75 85 115 120 163 9 16 13 16 78 106 121 164 171 232 5 8 15 16 110 149 170 230 240 325 3 4 1 1 8 192 261 297 403 420 569 7 8 1 5 16 306 416 474 642 669 907 1 1 1 2 467 634 722 979 1020 1383 METRIC SERIES Misie ee Bill A TORQUE KI Identification PP Aa etric etric A CHART Grade 8 8 Grade 10 9 COARSE THREAD FINE THREAD A MARKING ON HEAD MARKING ON
5. E SPECIFICATIONS Wrench Ref Cap Screw Qty Size Required Torque 7 M12 x 1 75P x 40 mm 8 18 mm 50 Ibs ft 68 N m 9 5 8 NC x 1 1 2 Carriage bolt GR5 10 15 16 170 Ibs ft 230 N m 12 M16 x 2 0P x 40 mm 8 24mm 125 Ibs ft 169 N m Install Grill Guard Optional 1 Align grill guard A with holes on front of tractor A 1019012 Grill guard frame and secure into position using four cap Includes hardware B C amp D screws B hardened flat washers D and hex B 307301 M12 x 1 75P x 40 mm HHCS nuts C C 307813 M12x 1 75 Hex nut 2 Torque to 50 lbs ft D 57816 1 2 Hardened flat washer ay CD6860 4 Figure 7 Grill Guard Installation As a valued customer Woods appreciates your comments Once loader mount and hydraulic hoses have been installed please take a few minutes to complete the Loader Mount Evaluation sheet that was supplied with this mount Your comments will help us continue to bring you quality products Maloate wa bdil Mount Installation 7 1019027 HOSE KIT INSTALLATION General Description These instructions are for operating the loader using the tractor hydraulic remote control lever To use this hydraulic connection the tractor must be equipped with the manufacturer s multi function hydraulic lever and four tractor hydraulic couplers Figure 9 Tractor Remote Control Connections Assemble Hoses 8 Attach 45 degree elbow 3 and male quick coupler 8 to the end of the four loa
6. HEAD A Diameter 8 A F A Diameter 8 Thread Pitch Wrench Metric 8 8 Metric 10 9 Metric 8 8 Metric 10 9 Thread Pitch Millimeters Size N m Ibs ft N m lbs ft N m Ibs ft N m lbs ft Millimeters 6x1 0 10 mm 8 6 11 8 8 6 11 8 6x1 0 8x 1 25 13 mm 20 15 27 20 21 16 29 22 8x1 0 10 x 1 5 16 mm 39 29 54 40 41 30 57 42 10 x 1 25 12 x 1 75 18 mm 68 50 94 70 75 55 103 76 12x 1 25 14x 2 0 21mm 109 80 151 111 118 87 163 120 14x 1 5 16 x 2 0 24 mm 169 125 234 173 181 133 250 184 16 x 1 5 18 x 2 5 27 mm 234 172 323 239 263 194 363 268 18 x 1 5 20 x 2 5 30 mm 330 244 457 337 367 270 507 374 20x 1 5 22 x 2 5 34 mm 451 332 623 460 495 365 684 505 22x 1 5 24 x 3 0 36 mm 571 421 790 583 623 459 861 635 24 x 2 0 30 x 3 0 46 mm 1175 867 1626 1199 1258 928 1740 1283 30 x 2 0 Typical Washer Flat Washer Installations Lock Washer N A dp om a fe NO ou 8 9 00 12 Appendix Bolt Torque amp Size Charts Rev 10 10 2005 BOLT SIZE CHART NOTE Chart shows bolt thread sizes and corresponding head wrench sizes for standard SAE and metric bolts SAE Bolt Thread Sizes 000 OOK 100 125 COOOOCS Metric Bolt Thread Sizes 8MM 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS IAG ki it andy et no po ene otan dp ba va dede rk Agriculture ING ines ce tae vl pote ou Vinca po ian pa National Coarse AU Picts ooiitisnsn sokeoiama adc Automatic Transmission Fluid NP kisa rizian detere nnna National Fine BSPP kaa
7. USIVE REMEDY UNDER THIS WARRANTY THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY WOODS MAKES NO OTHER WARRANTY EXPRESS OR IMPLIED AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE WOODS shall not be liable for any incidental or consequential losses damages or expenses arising directly or indirectly from the product whether such claim is based upon breach of contract breach of warranty negligence strict liability in tort or any other legal theory Without limiting the generality of the foregoing Woods specifically disclaims any damages relating to i lost profits business revenues or goodwill ii loss of crops iii loss because of delay in harvesting iv any expense or loss incurred for labor supplies substitute machinery or rental or v any other type of damage to property or economic loss This Warranty is subject to any existing conditions of supply which may directly affect WOODS ability to obtain materials or manufacture replacement parts No agent representative dealer distributor serviceperson salesperson or employee of any company including without limitation WOODS its authorized dealers distributors and service centers is authorized to alter modify or enlarge this Warranty Answers to any questions regarding warranty ALITEC Woods Equipment service and locations may be obtained by
8. WAIN ROY WEI WOODS 2 Introduction RE DORO SAFETY RULES ATTENTION BECOME ALERT YOUR SAFETY IS INVOLVED 4A iLEA EL INSTRUCTIVO Si no lee Ingles pida ayuda a alguien que si lo lea para que le traduzca las medidas de seguridad Safety is a primary concern in the design and manufacture of our products Unfortunately our efforts to provide safe equipment can be wiped out by an operator s single careless act In addition to the design and configuration of equipment hazard control and accident preven tion are dependent upon the awareness con cern judgement and proper training of personnel involved in the operation transport maintenance and storage of equipment It has been said The best safety device is an informed careful operator We ask you to be that kind of operator INSTALLATION m This Loader Mounting Kit is to be used only for the loaders and tractors specified in this manual Any other use or modification of this mounting kit may result in serious injury or death H Hydraulics must be connected as instructed in this manual Do not substitute parts modify or connect in any other way H After connecting hoses check that all control lever positions function as instructed in the Opera tor s Manual Do not put into service until control lever and equipment movements are correct H Safety instructions are important Read all attachment and power unit manuals follow all safety r
9. WOODS 211716 LOADER MOUNTING KIT for 1009 1012 LC96 LC102 Loaders on John Deere FWA ROPS Tractors 3120 3320 3520 3720 8 3203 Includes Hose Kit INSUZALILAT TON MANWAL 1019027 CO N 8 e a WOCD 2 Tested Proven Unbeatable TO THE DEALER Assembly and proper installation of this product is the responsibility of the Woods dealer Read manual instructions and safety rules Make sure all items on the Dealer s Pre Delivery and Delivery Check Lists in the Loader Operator s Manual are completed before releasing equipment to the owner TO THE OWNER Read this manual and Loader Operator s Manual before operating your Woods equipment The information presented will prepare you to do a better and safer job Keep this manual handy for ready reference Require all operators to read this manual carefully and become acquainted with all adjustment and operating procedures before attempting to operate Replacement manuals can be obtained from your dealer To locate your nearest dealer check the Dealer Locator at www WoodsEquipment com or in the United States and Canada call 1 800 319 6637 The equipment you have purchased has been carefully engineered and manufactured to provide dependable and satisfactory use Like all mechanical products it will require cleaning and upkeep Lubricate the unit as specified Observe all safety information in this manual and safety decals on the equipment For service your autho
10. contacting BMP Company 2606 South Illinois Route 2 CENTRAL FABRICATORS Post Office Box 1000 Oregon Illinois 61061 USA ear 800 319 6637 tel 800 399 6637 fax W l a lala WAIN ROY A w EDS WOODS www WoodsEquipment com F 3079 Rev 2 14 2011 PART NUMBER MANO0426 815 732 2141 tel 815 732 7580 fax W frre www WoodsEquipment com 4 A Jg D a A 2006 Woods Equipment Company All rights reserved WOODS the Woods logo and Tested Proven Unbeatable are trademarks of Woods Equipment Company All other trademarks trade names or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective companies or mark holders Specifications subject to change without notice
11. d full turn See your tractor opera tor s manual for instructions on steering stop adjustment Remove Hydraulic Coupler Bracket 1 Locate tractor female hydraulic couplers located in front of the right operator platform 2 Disconnect hydraulic couplers from hydraulic lines Identify the lines with a color code so that they can be reinstalled in the same location 3 Remove snap rings on back side of coupler bracket and remove hydraulic couplers from cou pler bracket 4 Remove two cap screws from tractor housing and remove coupler bracket shown in Figure 1 Figure 1 Remove Hydraulic Coupler Bracket 4 Mount Installation Rev 9 29 2011 MAN0426 3 3 2006 Install Coupler and Hose Line Brackets Tractor Hardware 1 Insert hydraulic couplers through new coupler bracket 2 and secure with snap rings NOTE Make sure hydraulic couplers are in the same color sequence as they were when they were removed Tractor Hydraulic San Connect couplers to the hydraulic feed lines Attach coupler bracket to tractor chassis using hardware previously removed 2 1019032 Bracket hydraulic coupler Install Right and Left Rear Mounts 1 Attach right rear mount 1 to tractor housing using four cap screws 12 and hardened flat washers 11 2 Repeat process for installation of left mount 2 1 1019010 Right rear mount 2 1019011 Left rear mount 11 57817 5 8 Hardened flat washer 12
12. der supply hoses 1 See m Figure 10 f Ta W QO 1 1018142 Hose 46 x 3 8 NPTM x 3 4 JICM A 3 313015 Elbow 3 8 NPTM x 3 8 NPTF 45 bias ee 1 8 64300 Quick coupler male 3 8 Figure 10 Hose Kit Assembly Connect Hoses to Loader 1 Connect the loader supply hoses to loader steel A BUCKET CYL BASE END feedlines DUMP RED B BUCKET CYL ROD END ROLLBACK BLUE C BOOM CYL ROD END DOWN YELLOW D BOOM CYL BASE END UP GREEN 2 Follow color code listed in Figure 11 LOADER FEEDLINES Figure 11 Loader Feedline Identification 8 Hydraulic Installation MANO426 3 3 2006 Connect Hoses to Tractor 1 2 Connect hydraulic hoses to tractor hydraulic couplers as shown in Figure 12 Attach color coded plastic bands around male quick couplers to identify quick coupler connections cpsses 3 Yellow John Deere Couplers oR A Black Green Yellow Red Woods Hoses oe Green Blue Figure 12 Hydraulic Hose Connection Verification of Control Movements 1 When Mount loader to tractor Remove mount pins from loader uprights Align tractor with loader and slowly drive tractor into loader Shut off tractor Connect loader feedline hoses to tractor hydraulic remote control hydraulic couplers See Figure 12 for hose connections Mount loader to tractor by activating bucket cylinders to raise or lower the loader uprig
13. eta kosa tip kwe r l pie etd jon ae ia kd n Mega Pascal UNS seat aat e ban lee de end anba kos aa ank minen Unified Special IN ize bn kape ou teh ke n ok aka da fk aaa akaes ai Newton Bolt Torque amp Size Charts Rev 10 10 2005 App e n dix 1 3 WARRANTY Replacement Parts For All Models Except Mow n Machine Zero Turn Mowers and Woods Boundary Utility Vehicles Woods Equipment Company WOODS warrants this product to be free from defect in material and workmanship for a period of ninety 90 days from the date of delivery of the product to the original purchaser with the exception of V belts which will be free of defect in material and workmanship for a period of 12 months Under no circumstances will this Warranty apply in the event that the product in the good faith opinion of WOODS has been subjected to improper operation improper maintenance misuse or an accident This Warranty does not cover normal wear or tear or normal maintenance items This Warranty is extended solely to the original purchaser of the product Should the original purchaser sell or otherwise transfer this product to a third party this Warranty does not transfer to the third party purchaser in any way There are no third party beneficiaries of this Warranty WOODS obligation under this Warranty is limited to at WOODS option the repair or replacement free of charge of the product if WOODS in its sole discretion deems it t
14. hts into the loader mounts Slowly drive tractor forward activating appropriate cylinders to engage loader completely into mounts Insert mounting pins to secure loader Comply with all Safety Rules and start the tractor Check that all hydraulic control lever positions operate the loader movements correctly as shown in Figure 13 If loader movements do not respond correctly shut off tractor relieve pressure and reconnect properly Loader control movements must be correct before proceeding Once all loader functions are correct start the tractor and operate the loader to check for leaks Purge any remaining air from the hydraulic system and check oil level hose routings and correct loader operations are verified place a matching colored band around male and female quick disconnect couplers The colored bands will make re installation easier when the loader is removed from the tractor 10 Be sure that adequate slack is left in the hoses so they can move as the loader moves through its full range of motion Before operating the loader make sure that the Pre Delivery Delivery and Pre Operation Check Lists from the Loader Operator s Manual have been completed FLOAT POSITION LOWER DUMP ROLLBACK Handle Forward Boom down Handle forward to limit Float position Handle back Boom up Handle to right Dump bucket or attachment Handle to left Rollback bucket or attachment Figu
15. o be defective or in noncompliance with this Warranty The product must be returned to WOODS with proof of purchase within thirty 30 days after such defect or noncompliance is discovered or should have been discovered routed through the dealer and distributor from whom the purchase was made transportation charges prepaid WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the product THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY WOODS MAKES NO OTHER WARRANTY EXPRESS OR IMPLIED AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE WOODS shall not be liable for any incidental or consequential losses damages or expenses arising directly or indirectly from the product whether such claim is based upon breach of contract breach of warranty negligence strict liability in tort or any other legal theory Without limiting the generality of the foregoing Woods specifically disclaims any damages relating to i lost profits business revenues or goodwill ii loss of crops iii loss because of delay in harvesting iv any expense or loss incurred for labor supplies substitute machinery or rental or v any other type of damage to property o
16. r Mounting Kit for mounting Woods 1009 1012 LC96 and LC102 loaders on John Deere 3120 3320 3520 3720 amp 3203 FWA ROPS tractors Any other use or modi fication of this mounting kit may result in serious injury or death IMPORTANT H This equipment must be assembled and installed on the customer s tractor by the Woods dealer Dealer must thoroughly inspect equipment and complete each item on the PRE DELIVERY CHECK LIST DELIVERY CHECK LIST and PROD UCT REGISTRATION before equipment is released to the customer m Clean threaded holes in the tractor chassis thoroughly using a tap of the proper size Paint rust or debris in the threads may not permit cap screws to be installed and tightened correctly For installing this mounting kit references to right left forward and rearward directions are determined from the operator s position in the tractor seat Leave all hardware loose until loader mount is com pletely assembled When assembly is completed torque hardware to specifications listed on page 7 of this manual 1 Shut off engine and set parking brake during installation 2 Remove the tractor front weights and front weight bracket if equipped 3 The tractor must be equipped with single multi function control lever joystick and hydraulic cou plers available through John Deere 4 Larger tires may require steering stop adjustment Tires must clear loader and loader mounts at full oscillation an
17. r conditions are listed below Part or Duration from date of Condition Model Number delivery to the original Warranted purchaser Gearbox Seals All units listed below 2 years BW1260 BW1620 BW1800 BW2400 8 years BW240HD BW180HD BW180HB BW126HB 7 years BB48X BB60X BB72X BB84X BB600X BB720X BB840X BB6000X BB7200X BB8400X Geatbox DS 1260 DSO1260 DS 1440 TS1680 BW 126 3 BW180 3 BW240 components PHD25 PHD35 PHD65 PHD95 2162 3240 DS96 DS120 RCC42 RMS50 2 RM660 2 RD990X PRD6000 PRD7200 PRD8400 S15CD S20CD S22CD S25CD S27CD BW180LH 5 years TC R74 TC R68 TC R60 TBW 144 TBW180 TBW204 6 years 3 years 1 year if used in rental or RDCS4 RD60 RD72 TBW150C TS R60 TS R52 TS R44 aes commercial applications spindles RM550 2 RM660 2 RD990X PRD6000 PRD7200 PRD8400 TBW 144 TBW180 TBW204 3 years BB600 BB720 BB840 BB6000 BB7200 BB8400 BW126 3 BW126HB BW180 3 BW180HB Rust through BW180HD BW1260 BW1800 BW240 BW240HD 2162 3240 DS1260 DSO1260 DS1440 10 years TS 1680 Under no circumstances will this Warranty apply in the event that the product in the good faith opinion of WOODS has been subjected to improper operation improper maintenance misuse or an accident This Warranty does not apply in the event that the product has been materially modified or repaired by someone other than WOODS a WOODS authorized dealer or di
18. r economic loss This Warranty is subject to any existing conditions of supply which may directly affect WOODS ability to obtain materials or manufacture replacement parts No agent representative dealer distributor service person salesperson or employee of any company including without limitation WOODS its authorized dealers distributors and service centers is authorized to alter modify or enlarge this Warranty Answers to any questions regarding warranty service and locations may be obtained by contacting ALITEC Woods Equipment BMP Company 2606 South Illinois Route 2 CENTRAL FABRICATORS Post Office Box 1000 GANNON Oregon IL 61061 rm 800 319 6637 tel Peres 800 399 6637 fax WOODS W SUT Do Pe www WoodsEquipment com F 8494 Rev 6 23 2005 WARRANTY All Models Except Mow n Machine Zero Turn Mowers Please Enter Information Below and Save for Future Reference Date Purchased From Dealer Model Number Serial Number Woods Equipment Company WOODS warrants this product to be free from defect in material and workmanship Except as otherwise set forth below the duration of this Warranty shall be for TWELVE 12 MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE PRODUCT TO THE ORIGINAL PURCHASER All current model loaders and backhoes are warranted for two 2 years from the date of delivery to the original purchaser The warranty periods for specific parts o
19. re 13 Single Lever Control Operation MAN0426 3 3 2006 Hydraulic Installation 9 211716 LOADER MOUNTING KIT CD6860 REF PART QTY DESCRIPTION 1 1019010 1 Right rear mount 2 1019011 1 Left rear mount 3 1019013 2 Side rail 4 1034180 1 Right front mount 5 1034181 1 Left front mount 6 230 10 5 8 NC Hex nut 7 307301 8 M12x 1 75P x 40 mm HHCS 8 307813 8 Mi2x 1 75P Hex nut 9 5607 10 5 8 NC x 1 1 2 Carriage bolt 10 57816 8 1 2 Hardened flat washer 11 57817 18 5 8 Hardened flat washer 12 64062 8 M16x2 0P x 40 mm Cap screw Standard hardware obtain locally 10 Parts 1019012 Grill Guard Optional REF PART QTY DESCRIPTION A 1019012 1 Grill guard includes items B D B 307301 4 M12x 1 75P x 40 mm HHCS C 307813 4 M12 x 1 75P Hex nut D 57816 4 1 2 Hardened flat washer Rev 9 29 2011 MAN0426 3 3 2006 1019027 HOSE KIT John Deere Couplers ot Black Green Yellow Red Woods Hoses Tractor Hardware D Yellow Green Blue Red TRACTOR FITTINGS REF PART QTY DESCRIPTION 1 1018142 4 Hose 46 x 3 8 NPTM x 3 4 JICM 2 1019032 1 Bracket coupler 1 3 313015 4 Elbow 3 8 NPTM x 3 8 NPTF 45 4 395061 2 Plastic spiral band red 5 395062 2 Plastic spiral band blue 6 56061 2 Plastic spiral band green 7 56062 2 Plastic spiral band yellow 8 64300 4 Quick coupler male 3 8 Z n 88 AR Plastic tie Standard hardware obtain locally NS Not shown AR As required MAN
20. rized Woods dealer has trained mechanics genuine Woods service paris and the necessary tools and equipment to handle all your needs Use only genuine Woods service parts Substitute parts will void the warranty and may not meet standards required for safe and satisfactory operation Record the model number of your equipment in the space provided Model Date of Purchase Provide this information to your dealer to obtain correct repair parts Throughout this manual the term NOTICE is used to indicate that failure to observe can cause damage to equipment The terms CAUTION WARNING and DANGER are used in conjunction with the Safety Alert Symbol a triangle with an exclamation mark to indicate the degree of hazard for items of personal safety injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death Indicates a hazardous situation which if not avoided will result in death A DANGER or serious injury A WARNING Indicates a hazardous situation which if not avoided could result in death or serious injury T This is the safety alert symbol It is used to alert you to potential personal A CAUTION Indicates a hazardous situation which if not avoided could result in minor or moderate injury IMPORTANT Is used to address practices not related to personal injur or NOTICE i j NOTE Indicates helpful information ALITEC BMP CENTRAL FABRICATORS GANNON GILL W Aa e
21. stributor and or a WOODS authorized service center This Warranty does not cover normal wear or tear or normal maintenance items This Warranty also does not cover repairs made with parts other than those obtainable through WOODS This Warranty is extended solely to the original purchaser of the product Should the original purchaser sell or otherwise transfer this product to a third party this Warranty does not transfer to the third party purchaser in any way There are no third party beneficiaries of this Warranty WOODS makes no warranty express or implied with respect to engines batteries tires or other parts or accessories not manufactured by WOODS Warranties for these items if any are provided separately by their respective manufacturers WOODS obligation under this Warranty is limited to at WOODS option the repair or replacement free of charge of the product if WOODS in its sole discretion deems it to be defective or in noncompliance with this Warranty The product must be returned to WOODS with proof of purchase within thirty 30 days after such defect or noncompliance is discovered or should have been discovered routed through the dealer and distributor from whom the purchase was made transportation charges prepaid WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the product THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCL
22. ules and safety decal information Replace ment manuals and safety decals are available from your dealer To locate your nearest dealer check the Dealer Locator at www WoodsEquipment com or in the United States and Canada call 1 800 319 6637 Failure to follow instructions or safety rules can result in serious injury or death E Keep hands and body away from pressurized lines Use paper or cardboard not hands or other body parts to check for leaks Wear safety goggles Hydraulic fluid under pressure can easily penetrate skin and will cause serious injury or death 3 Safety H Make sure that all operating and service person nel know that if hydraulic fluid penetrates skin it must be surgically removed as soon as possible by a doctor familiar with this form of injury or gan grene serious injury or death will result CON TACT A PHYSICIAN IMMEDIATELY IF FLUID ENTERS SKIN OR EYES DO NOT DELAY H Check that all hardware is properly installed Always tighten to torque chart specifications unless instructed otherwise in this manual E Air in hydraulic systems can cause erratic oper ation and allows loads or equipment components to drop unexpectedly When connecting equipment or hoses or performing any hydraulic maintenance purge any air in hydraulic system by operating all hydraulic functions several times Do this before putting into service or allowing anyone to approach the equipment E Protective hose sleeves must cover
Download Pdf Manuals
Related Search