Whirlpool Dishwasher WDF530PLY User's Manual
Contents
1. not solder within 6 15 2 cm of the water inlet valve Drain Requirements A new drain hose is supplied with your dishwasher If this is not long enough use a new drain hose with a maximum length of 12 3 7 m Part Number 3385556 that meets all current AHAM IAPMO test standards is resistant to heat and detergent and fits the 1 2 9 cm drain connector of the dishwasher EO ex cade pte aris fe Y Tea DD L0 P a u Insulation may be compressed not used on all models a A B Make sure to connect the drain hose to waste tee or Depth Height disposer inlet above drain trap in house plumbing and 20 50 8 cm minimum above the floor It is recommended that the drain hose either be looped up and securely fastened to the underside of the counter or be connected to an air gap Stainless steel 2478 332 tub models 63 2 cm 85 1 cm Plastic tub 2514 337 models 64 1 cm 86 cm Make sure to use an air gap if the drain hose is connected to house plumbing lower than 20 Ss 50 8 cm above subfloor or Zl floor Use 1 2 1 3 cm minimum E D drain line fittings If required the air gap Should be installed in accordance with the air gap installation instructions When connecting the air gap a rubber hose not provided will be needed to connect to the waste tee or disposer unit air gap Page 1 of 2 Because Whirlpool Corporation poli2. lt gt _ e Whirl ol Undercounter Dishwasher PRODUCT MODEL NUMBERS PRODUCT DIMENSIONS WDF510PAY WDT710PAY WDF530PAY WDT770PAY WDF530PLY WDT790SAY WDF530PSY WDT790SLY WDF730PAY WDT910SAY WDF750PAY WDT910SSY Beyn WDF780SLY Electrical Requirements 120 volt 60 Hz AC only 15 or 20 amp fused electrical supply Copper wire only A time delay fuse or circuit breaker and separate circuit is recommended a If direct wiring dishwasher Use flexible armored or nonmetallic sheathed copper wire with grounding wire that meets the wiring requirements for your home and local codes and ordinances Use a UL Listed or CSA Approved strain relief If connecting dishwasher with a power supply cord Use Power Supply Cord Kit Pat Min l Number 4317824 marked for use roca th with dishwashers Follow the kit instructions for installing Veg the power supply cord Power supply cord must plug into a grounded three prong outlet located in the cabinet next to the dishwasher opening Outlet must meet all local codes and ordinances Water Supply Requirements A hot water line with 20 to 120 psi 138 to 862 kPa water pressure Water temperature must be 120 F 49 C water at dishwasher Use 3 0 D copper tubing with compression fitting or flexible braided water supply line Part Number 4396897RP Y2 minimum plastic tubing is not recommended Use a 90 elbow with 3 4 hose connection with rubber washer Do
3. cy includes a continuous commitment to improve Dimensions are for planning purposes only For complete details see Installation Ref W10350361A Our products we reserve the right to change materials and specifications without notice Instructions packed with product Specifications subject to change without notice 6 10 11 CABINET CUTOUT DIMENSIONS NOTE Shaded areas of cabinet walls show where utility connections may be installed Measured from the lowest point on the underside of countertop May be reduced to 33 85 1 cm for stainless steel tub models or 33 86 cm for plastic tub models by removing wheels from dishwasher Minimum measured from narrowest point of opening Check that all surfaces have no protrusions that would prohibit dishwasher installation Page 2 of 2 Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only For complete details see Installation Ref W10350361A Our products we reserve the right to change materials and specifications without notice Instructions packed with product Specifications subject to change without notice 6 10 11
Download Pdf Manuals
Related Search