Whirlpool SAWB600JQ1 User's Manual
Contents
1. 4 Run washer on a drain and spin setting see Drain and Spin for about 30 seconds to mix the antifreeze and water 5 Unplug washer or disconnect power To use washer again 1 Flush water pipes and hoses 2 Reconnect water inlet hoses 3 Turn on both water faucets 4 Plug in washer or reconnect power 5 Run the washer through a complete cycle with 1 cup 250 mL of detergent to clean out antifreeze TROUBLESHOOTING First try the solutions suggested here and possibly avoid the cost of a service call Washer won t fill rinse or agitate Check the following Is the power cord plugged into a grounded 3 prong outlet Is the indicator on the Cycle Control knob properly lined up with a cycle Turn the Cycle Control knob to the right slightly and pull to start Are the water inlet valve screens clogged Are both the hot and cold water faucets turned on Is the water inlet hose kinked Does the water level seem too low or does the washer appear to not fill completely The top of the agitator is much higher than the highest water level This creates a perception that the washer is not filling completely However this is normal Washer stops Check the following Is the power cord plugged into a grounded 3 prong outlet Is the indicator on the Cycle Control knob properly lined up with a cycle Turn the Cycle Control knob to the right slightly and pull to start Are the water inlet valve screens clogged2. Washer basket is crooked m Was the washer basket pulled forward during loading The wash load should be balanced and not overloaded Push the basket to the center before starting wash m Is the load balanced and the washer level The wash load should be balanced and not overloaded The washer must be level The front feet should be properly installed and the nuts tightened Reset the rear leveling legs if needed See the Installation Instructions m The washer basket moves while washing This is normal Agitator operation The top of the agitator is loose or moves in only one direction This is normal Dispensers clogged or bleach leaking Did you follow the manufacturer s directions when adding detergent and fabric softener to the dispensers Measure detergent and fabric softener Carefully pour into the dispensers Wipe up all spills Dilute fabric softener in the fabric softener dispenser Did you put powdered or color safe bleach in the liquid chlorine bleach dispenser Add powdered or liquid color safe bleach directly to the basket Do not use the chlorine bleach dispenser for color safe bleach Load too wet Did you use the right cycle for the load being washed Select a cycle with a higher spin speed if available Did you use a cold rinse Cold rinses leave loads wetter than warm rinses This is normal Residue or lint on load Did you sort properly Sort lint givers towels chenille from lint ta
3. Are both the hot and cold water faucets turned on Is the water inlet hose kinked Is there power at the plug Check your electrical source or call an electrician Has a fuse blown or is the circuit breaker open If problem continues call an electrician Are you using an extension cord Do not use an extension cord Is the washer in a normal pause in the Permanent Press or Hand Washables cycle The washer pauses for about 2 minutes in the Permanent Press cycle Allow the cycle to continue The Hand Washables cycle on some models features periods of agitation and soak Is the washer overloaded Wash smaller loads Washer won t drain or spin Is the drain hose clogged or the end of the drain hose more than 96 in 2 4 m above the floor See the Installation Instructions for proper installation of drain hose Is the lid open The lid must be closed during operation Is there excessive sudsing Always measure detergent Follow manufacturer s directions If you have very soft water you might need to use less detergent m Is your voltage low Check your electrical source or call an electrician Do not use an extension cord Washer continues to fill or drain or the cycle seems stuck m isthe top of drain hose lower than the water level in washer The top of the hose must be higher than the water level in the washer for proper operation See the Installation Instructions Does the drain hose fit too tightl
4. To avoid spilling use a cup with a pouring spout Do not let Never place items in the washer that are bleach splash drip or run down into the washer basket dampened with gasoline or other flammable m Use only liquid chlorine bleach in this dispenser fluids NOTE On models without a bleach dispenser see Adding Liquid Chlorine Bleach 3 OPTIONAL STEP Pour measured liquid fabric softener into the Do not dry anything that has ever had any type of liquid fabric softener dispenser on some models Softener is oil on it including cooking oils added automatically during the rinse portion of the cycle No washer can completely remove oil Doing so can result in death explosion or fire A WARNING Dilute liquid fabric softener by filling the dispenser with warm water until liquid reaches the crossbar in the opening m Do not spill or drip any fabric softener on the clothes m Use only liquid fabric softener in this dispenser NOTE On models without a fabric softener dispenser see Adding Liquid Fabric Softener 4 Close the washer lid Electrical Shock Hazard 5 Turn the LOAD SIZE selector to the correct setting for your wash load and the type of fabric being washed Plug inio a grounded Sprong outlet m Choose a load size that allows the load to move freely for Do not remove ground prong best fabric care See Loading Do not use an adapter m You may change the load size selection after the washer has st
5. 3955164B TWO SPEED AUTOMATIC WASHERS Use amp Care Guide For questions about features operation performance parts accessories or service call 1 800 253 1301 or visit our website at www whirlpool com Table of Contents ccccccccccscsceeeeeesesesessssesssseaees 2 TABLE OF CONTENTS WASHER SAFETY ccssccsscesseestessnenserseeeseerseesseesseesseeneeeseeennensennaees 3 PARTS AND FEATUREG sccssesssseeestessenserseeeseeeseseeesseneeeneeens 4 WASHER UTC 5 Understanding Washer Cycles ak 5 Kor Tu DEEN 5 Normal SOUNAS siini iasi aaa agaaa 5 Starting Your Washer ANA 6 Selecting a Cycle and Time 7 Rinse and Spits ic osn dee ae es 7 Drain and KL BEE 7 Adding Liquid Chlorine Bleach AAA 8 Adding Liquid Fabric Softener AAA 8 WASHER CARE escsssecstesstessceseeeneeeseesseessneneerseesneeeseessneneneneeeneesne Cleaning Your Washer Water Inlet Hee ege suerge avi EVERE ENNEN Vacation Storage and Moving Care 8 TROUBLESHOOTING cscssessecsseeseenseeseeeseeeseesseeeseesserseeneeesoeneees 9 ASSISTANCE OR SERVICE ccsccssesseestssesseesenenseesesseessenseeens 11 WARRANTY E eE E TAA 12 WASHER SAFETY Your safety and the safety of others are very important We have provided many important safety messages in this manual and on your appliance Always read and obey all safety messages This is the safety alert symbol This symbol alerts you to potential hazards that can kill or hu
6. AVY 12 wy SUPER 18 OFF EXTRA RINSE OFF N 6 SPIN WasH RINSE LOAD SIZE TEMPERATURE EXTRA RINSE CYCLE SIGNAL RINSE Ging E HAND WASHABLES 60FF EXTRA SPIN DELICATES WASHER USE When the Cycle Control knob is set to a number and pulled out the washer fills to the selected load size before agitation and timing start The washer begins agitating immediately after filling agitation occurs with the washer lid up or down During agitation the agitator creates a continuous rollover action on some models that provides a thorough cleaning of the wash load After agitation starts the Cycle Control knob turns clockwise until it points to an OFF area and the cycle ends NOTE The washer pauses briefly throughout each cycle These pauses are normal for washer operation Loading suggestions For these suggested full sized loads set the LOAD SIZE or WATER LEVEL selector to the highest setting SUPER CAPACITY WASHERS Heavy Work Clothes 3 pair pants 1 coverall 3 shirts 1 overall 4 pair jeans Delicates 3 camisoles 2 sets of sleepwear 1 quilted robe 1 child s outfit 4 slips 6 undergarments Towels 10 bath towels 14 washcloths 10 hand towels 1 bath mat Mixed Load 3 double sheets 2 shirts 4 pillowcases 2 blouses 8 T shirts 8 handkerchiefs WASH RINSE 6 pair shorts 1 Fill 1 Fill EXTRA LARGE CAPACITY WASHERS Heavy Work Clothes 2 pair pants 3 pair jea
7. SE LIGHT 6 REGULAR 9 HEAVY 12 y SPIN SUPER 18 EXTRA RINSE OFF EXTRA RINSE RINSE RINSE HAND WASHABLES Sorf extra SPIN DELICATES RINSE Cycle Control knob Normal cycle This cycle features high speed agitation followed by a brief period of low speed agitation for cleaning cottons and linens High spin speeds shorten drying time Select 6 9 or 12 minutes of wash time depending on whether your load is lightly moderately or heavily soiled Super Select the Super setting to wash heavily soiled loads that need maximum soil removal Use twice the amount of detergent recommended for a wash cycle Permanent Press cycle This cycle starts with high speed agitation and then steps down to low speed agitation for cleaning permanent press blends and synthetic fabrics To minimize wrinkling this cycle features a cool down rinse and a low speed final spin Select 6 or 9 minutes of wash time to clean lightly to moderately soiled loads Delicates cycle This cycle features a low speed agitation for gentle soil removal from delicate items and washable knits Low spin speeds minimize wrinkling Use this 6 minute cycle to clean lightly to moderately soiled loads Hand Washables cycle This cycle features a series of brief low speed agitations and short soaks to gently clean special care items Low spin speeds minimize wrinkling Wash small loads If items appear to be floating due to trapped air stop the washer by pushing
8. arted filling by turning the selector to a different setting Do not use an extension cord Failure to follow these instructions can result in death fire or electrical shock 1 Measure detergent and pour it into the washer If desired add 6 Set the TEMPERATURE selector to the correct setting for the powdered or liquid color safe bleach Add extra detergent for type of fabric and soils being washed Use the warmest water the Super Wash cycle safe for fabric Follow garment label instructions Water Temp Use For Hot Whites and pastels 111 F 44 C Heavy soils or above Drop a sorted load of clothes loosely into your washer Ze Si Z G t mt 4 Warm Bright colors m Load evenly to maintain washer balance Mix large an 90 110 F i small items 32 43 C Moderate to light soils m Items should move easily through the wash water Overloading can cause poor cleaning Cold Colors that bleed or fade m To reduce wrinkling of permanent press clothes and some 70 90 F Light soils synthetic knits use a large load size to provide more 21 32 C space see step 5 NOTE In wash water temperatures colder than 70 F 21 C detergents do not dissolve well Soils can be difficult to remove Some fabrics can retain wear wrinkles and have increased pilling the formation of small lint like balls on the surface of garments 7 OPTIONAL STEP Set the EXTRA RINSE selector on some models to ON if you want an additional rins
9. broken threads in seams before washing Did you overload the washer The wash load must be balanced and not overloaded Loads should move freely during washing Did you properly add chlorine bleach Do not pour chlorine bleach directly on load Wipe up bleach spills Undiluted bleach will damage fabrics Did you follow the manufacturer s care label instructions ASSISTANCE OR SERVICE Before calling for assistance or service please check Troubleshooting It may save you the cost of a service call If you still need help follow the instructions below When calling please know the purchase date and the complete model and serial number of your appliance This information will help us to better respond to your request If you need replacement parts If you need to order replacement parts we recommend that you only use Factory Specified Parts These parts will fit right and work right because they are made with the same precision used to build every new KIRKLAND SIGNATURE appliance by Whirlpool Corporation To locate Factory Specified Parts in your area call the Customer Interaction Center or your nearest designated service center For assistance or service Call the Whirlpool Customer Interaction Center toll free 1 800 253 1301 Our consultants provide assistance with Features and specifications on our full line of appliances Installation information Use and maintenance procedures Accessory and repair parts sale
10. cycle Pour bleach around the agitator not directly onto the load m Follow directions on the care labels Do not use chlorine bleach on wool silk spandex acetates or some flame retardant fabrics m When soaking with chlorine bleach add detergent to soak water NOTE Undiluted bleach will damage any fabric it touches The damage appears as rips holes tears or color loss and may not show up until several washings later Always dilute fabric softener with 1 2 to 1 cup 125 to 250 mL warm water Undiluted fabric softener can stain fabrics m Add diluted fabric softener only in the final rinse m Fabric softener should not be mixed with other laundry products Greasy stains can form To remove greasy stains wet the stain and rub with liquid detergent or a bar of soap Rewash m Too much fabric softener can make some items diapers and towels nonabsorbent If this happens use less fabric softener or do not use it every time WASHER CARE Cleaning the exterior Use a soft damp cloth or sponge to wipe up any spills such as detergent or bleach Occasionally wipe the outside of your washer to keep it looking new Cleaning the interior Clean your washer interior by mixing 1 cup 250 mL of chlorine bleach and 2 cups 500 mL of detergent Pour this into your washer and run it through a complete cycle using hot water Repeat this process if necessary NOTE Remove any hard water deposits using only cleaners lab
11. d it You will Phone number need to know your complete model number and serial number You can find this information on the model and serial number label plate located on your appliance as shown in Parts and Features Model number Serial number Purchase date Distributed by Costco Wholesale P O Box 34535 Seattle WA 98124 1535 U S A 1 800 774 2678 Shop at www costco com Assembled in U S A 3955164B 9 02 2002 All rights reserved Registered Trademark TM Trademark of Costco Wholesale Corporation Printed in U S A
12. e and spin at the end of a wash cycle 8 OPTIONAL STEP Set the END OF CYCLE SIGNAL selector on some models to ON if you want your washer to alert you when the wash cycle is complete The signal is helpful when you are washing items that should be removed from the washer as soon as the cycle ends 9 Push in the Cycle Control knob and turn it clockwise to the wash cycle you want Reduce the wash time when using a small load size setting See Selecting a Cycle and Time Rese Pull out the Cycle Control knob to start the washer To stop or restart your washer m To stop the washer at any time push in the Cycle Control knob m To restart the washer close the lid if open and pull out the Cycle Control knob This section describes the available wash cycles and will help you make the best cycle selections for your wash loads Each cycle is designed for different types of fabric and soil levels m The washer pauses briefly throughout each cycle These pauses are normal Refer to Normal Sounds to learn more about the sounds you may hear during a wash cycle m Refer to Understanding Cycles to learn what happens during a wash cycle NOTE This manual covers several different models The washer you purchased may vary from the model shown and will not have all of the cycles described EXTRA RINSE OFF REGULAR NORMAL SPIN 9 e LIGHT PERMANENT RINE W COOL PRESS egene PAUSE PULL TO START PUSH TO STOP RIN
13. eled as washer safe Cleaning the liquid fabric softener dispenser Flush dispenser periodically with warm water as shown Remove the dispenser by grasping the top of the dispenser with both hands and squeezing and pushing upward with thumbs Clean the dispenser by rinsing it under a water faucet Replace it after cleaning NOTE Do not wash clothes with this dispenser removed Do not add detergent or bleach to this dispenser it is for liquid fabric softener use only Replace inlet hoses after five years of use to reduce the risk of hose failure Periodically inspect and replace inlet hoses if bulges kinks cuts wear or leaks are found When replacing your inlet hoses mark the date of replacement on the label with a permanent marker Install and store your washer where it will not freeze Because some water may stay in the hoses freezing can damage your washer If storing or moving your washer during freezing weather winterize it Non use or vacation care Operate your washer only when you are at home If you will be on vacation or not using your washer for an extended period of time you should m Unplug washer or disconnect power m Turn off the water supply to the washer This helps avoid accidental flooding due to a water pressure surge while you are away To winterize washer 1 Shut off both water faucets 2 Disconnect and drain water inlet hoses 3 Put 1 qt 1 L of R V type antifreeze in the basket
14. g washing Was the wash water warm enough to relax wrinkles or are you using warm rinses If safe for the load use warm or hot wash water Use cold rinse water Are the hot and cold water hoses reversed Check to be sure the hot and cold water hoses are connected to the right faucets See the Installation Instructions Load is tangled or twisted Did you overload the washer The wash load must be balanced and not overloaded Loads should move freely during washing Did you wrap items around the agitator Drop items loosely into the washer Do not wrap items around the agitator Gray whites dingy colors Did you properly sort the load Dye transfer can occur when mixing whites and colors in a load Sort dark clothes from whites and lights Was the wash temperature too low Use hot or warm washes if safe for the load Hot water should be at least 111 F 44 C to clean heavy soils Did you use enough detergent or do you have hard water Use more detergent for washing heavy soils in cold or hard water Are the hot and cold water hoses reversed Check to be sure the hot and cold water hoses are connected to the right faucets See the Installation Instructions Garment damage Check the following Were sharp items removed from pockets before washing Empty pockets zip zippers snap or hook fasteners before washing Were strings and sashes tied to prevent tangling Were items damaged before washing Mend rips and
15. in the Cycle Control knob Push items down into the washer Restart the washer Soak cycle This cycle features brief periods of agitation and soak time to help remove heavy soils and stains that need pretreatment Use warm water when soaking laundry Hot water can set stains Use the amount of detergent or presoak additive recommended by the manufacturer After the Soak cycle ends add detergent and set a new wash cycle When using extra detergent for heavily soiled clothes or washing special care items you may find an extra rinse and spin is needed 1 Push in the Cycle Control knob and turn it clockwise to any of the Rinse settings 2 Pull out the Cycle Control knob The washer fills to the selected load size agitates drains and spins NOTE An Extra Rinse option is available on some models See Starting Your Washer A drain and spin may help shorten drying times for some heavy fabrics or special care items by removing excess water 1 Push in the Cycle Control knob and turn it clockwise to any of the Spin settings 2 Pull out the Cycle Control knob The washer drains then spins Always measure liquid chlorine bleach Do not guess Never use more than 1 cup 250 mL for a full load Follow manufacturer s directions for safe use Use a cup with a pouring spout to avoid spilling 1 Let the washer fill and begin agitating the load 2 Add bleach to the wash cycle so it can be removed in the rinse
16. kers corduroy synthetics Also sort by color Did you overload the washer The wash load must be balanced and not overloaded Lint can be trapped in the load if overloaded Wash smaller loads Check the following Was paper or tissue left in the pockets Did you use enough detergent Follow manufacturer s directions Use enough detergent to hold the lint in the water Is your water colder than 70 F 21 C Wash water colder than 70 F 21 C may not completely dissolve the detergent Stains on load Did you follow the manufacturer s directions when adding detergent and fabric softener Measure detergent and fabric softener Use enough detergent to remove soil and hold it in suspension Dilute fabric softener and add to the rinse portion of a cycle only Do not drip fabric softener on clothes Is there above average iron rust in water You may need to install an iron filter Did you properly sort the load Sort dark clothes from whites and lights Did you unload the washer promptly To avoid dye transfer unload the washer as soon as it stops 10 Load is wrinkled Did you unload the washer promptly Unload the washer as soon as it stops Did you use the right cycle for the load being washed Use the Permanent Press cycle or another cycle with low spin speeds if available to reduce wrinkling Did you overload the washer The wash load must be balanced and not overloaded Loads should move freely durin
17. ns 2 Wash 2 Rinse 3 shirts 1 coverall selected time Delicates 3 camisoles 2 bras 4 slips 2 nighties 4 panties 3 Draint 3 Drain No agitation No agitation Towels 8 bath towels 10 washcloths 8 hand towels 1 bath mat 4 Spin 4 Spin Spray rinse Mixed Load 2 double sheets or 6 pair shorts 1 king size sheet s 2 shirts 4 pillowcases 2 blouses 5 Spin t The Permanent Press cycle partially drains fills agitates briefly and drains 6 T shirts 6 handkerchiefs Your new washer may make sounds your old one didn t Because the sounds might be unfamiliar you may be concerned about them These sounds are normal During washing When you select a small load size setting your washer has a lower water level This can cause a clicking sound from the upper part of the agitator During drain If water is drained quickly from your washer depending on your installation you may hear air being pulled through the pump during the end of draining After drain and before spin When the cycle changes from draining to spinning you may hear gears engaging 2 OPTIONAL STEP Pour measured liquid chlorine bleach into the liquid chlorine bleach dispenser on some models Bleach will be dispensed automatically during the wash part of the cycle AWARNING m Never use more than 1 cup 250 mL for a full load Use less with a smaller load size Follow the manufacturer s directions for safe use Fire Hazard EE m
18. nutes This will release any accumulated hydrogen gas As the gas is flammable do not smoke or use an open flame during this time m Do not allow children to play on or in the washer Close supervision of children is necessary when the washer is used near children m Before the washer is removed from service or discarded remove the door or lid m Do not reach into the washer if the drum tub or agitator is moving m Do not install or store the washer where it will be exposed to the weather m Do not tamper with controls m Do not repair or replace any part of the washer or attempt any servicing unless specifically recommended in this manual or in published user repair instructions that you understand and have the skills to carry out m See Electrical Requirements for grounding instructions SAVE THESE INSTRUCTIONS PARTS AND FEATURES This manual covers several different models The washer you have purchased may have some or all of the parts and features listed below 1 5 2 6 3 7 4 8 Control panel 7 Basket Model and serial number label 8 Tub Liquid fabric softener dispenser Additional feature your washer may have Agitator White porcelain basket Lid Liquid bleach dispenser pm bo bz tOn some models Control panel EXTRA opp REGULAR NORMAL seine 9gLIGHT PERMANENT PRESS RINSE la SOWN Pave PULL TO START MEDIUM LARGE PUSH TO STOP RINSE O D O D LIGHT 6 REGULAR 9 HE
19. rt you and others All safety messages will follow the safety alert symbol and either the word DANGER or WARNING These words mean ADANGER AWARNING You can be killed or seriously injured if you don t immediately follow instructions You can be killed or seriously injured if you don t follow instructions All safety messages will tell you what the potential hazard is tell you how to reduce the chance of injury and tell you what can happen if the instructions are not followed IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of fire electric shock or injury to persons when using the washer follow basic precautions including the following m Read all instructions before using the washer m Do not wash articles that have been previously cleaned in washed in soaked in or spotted with gasoline dry cleaning solvents other flammable or explosive substances as they give off vapors that could ignite or explode m Do not add gasoline dry cleaning solvents or other flammable or explosive substances to the wash water These substances give off vapors that could ignite or explode m Under certain conditions hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more HYDROGEN GAS IS EXPLOSIVE If the hot water system has not been used for such a period before using the washing machine turn on all hot water faucets and let the water flow from each for several mi
20. s Specialized customer assistance Spanish speaking hearing impaired limited vision etc m Referrals to local dealers repair parts distributors and service companies Whirlpool designated service technicians are trained to fulfill the product warranty and provide after warranty service anywhere in the United States To locate the Whirlpool designated service company in your area you can also look in your telephone directory Yellow Pages For further assistance If you need further assistance you can write to Whirlpool Corporation with any questions or concerns at Whirlpool Corporation Customer Interaction Center 553 Benson Road Benton Harbor MI 49022 2692 Please include a daytime phone number in your correspondence Gearcase assembly covered by your warranty 11 WASHER WARRANTY TWO YEAR FULL WARRANTY For two years from the date of purchase when this washer is operated and maintained according to instructions attached to or furnished with the product Whirlpool Corporation will pay for Factory Specified Parts and repair labor to correct defects in materials or workmanship Service must be provided by a Whirlpool designated service company SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON TOP LID AND GEARCASE ASSEMBLY In the second through fifth years from the date of purchase when this washer is operated and maintained according to instructions attached to or furnished with the product Whirlpool Corporation
21. ty periods Replacement parts or repair labor costs for units operated outside the United States Pickup and delivery This product is designed to be repaired in the home Repairs to parts or systems resulting from unauthorized modifications made to the appliance Nog s THIS KIRKLAND SIGNATURE APPLIANCE IS WARRANTED BY WHIRLPOOL CORPORATION WHIRLPOOL CORPORATION IS NOT LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES Some states do not allow the exclusion or limitation of incidental or consequential damages so this exclusion or limitation may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Outside the 50 United States this warranty does not apply Contact your local Kirkland Signature dealer to determine if another warranty applies If you need service first see Troubleshooting Additional help can be found by checking Assistance or Service or call our Customer Interaction Center at 1 800 253 1301 from anywhere in the U S A or write Whirlpool Corporation Customer Interaction Center 553 Benson Road Benton Harbor MI 49022 2692 4 00 Keep this book and your sales slip together for future gt 7 S Dealer name reference You must provide proof of purchase or installation date for in warranty service Address Write down the following information about your washer to better help you obtain assistance or service if you ever nee
22. will pay for Factory Specified Parts for any top and lid rust and any part of the gearcase assembly if defective in materials or workmanship SECOND THROUGH TENTH YEAR LIMITED WARRANTY ON OUTER TUB In the second through tenth years from the date of purchase when this washer is operated and maintained according to instructions attached to or furnished with the product Whirlpool Corporation will pay for Factory Specified Parts for the outer tub should it crack or fail to contain water if defective in materials or workmanship LIFETIME LIMITED WARRANTY ON WHITE PORCELAIN BASKET For the lifetime of the washer when this washer is operated and maintained according to instructions attached to or furnished with the product Whirlpool Corporation will pay for Factory Specified Parts for the white porcelain basket should it chip or rust due to defects in materials or workmanship Whirlpool Corporation will not pay for 1 Service calls to correct the installation of your washer to instruct you how to use your washer or to replace house fuses or correct house wiring or plumbing 2 Repairs when your washer is used in other than normal single family household use 3 Damage resulting from accident alteration misuse abuse fire flood acts of God improper installation installation not in accordance with local electrical and plumbing codes or use of products not approved by Whirlpool Corporation Any labor costs during the limited warran
23. y in the standpipe or is it taped to the standpipe The drain hose should be loose yet fit securely Do not seal the drain hose with tape The hose needs an air gap See the Installation Instructions Washer makes noise m Is the load balanced and the washer level The wash load should be balanced and not overloaded The washer must be level The front feet should be properly installed and the nuts tightened Reset the rear leveling legs if needed See the Installation Instructions m Did you completely remove the yellow shipping strap with cotter pins See the Installation Instructions m Are the gears engaging after the drain and before spin or is the upper part of agitator clicking during wash These are normal washer noises Washer leaks m Check the following Are the fill hoses tight Are the fill hose washers properly seated Is the drain hose clamp properly installed See the Installation Instructions m isthe sink or drain clogged Sink and standpipe must be able to handle 17 gal 64 L of water per minute m Is water deflecting off the tub ring or the load Center the tub before starting the washer The wash load should be balanced and not overloaded The fill or spray rinses can deflect off the load The washer must be level The front feet should be properly installed and the nuts tightened Reset the rear leveling legs if needed See the Installation Instructions m Check household plumbing for leaks
Download Pdf Manuals
Related Search