Whirlpool KEHU309SSS User's Manual
Contents
1. Check local codes for type of connection required quick connect adapter fitting you just installed on the filter Copper water supply tubing must be cut with a copper tubing outlet blue side of the water filter cutter so the ends are concentric and without burrs NOTE It is recommended that the cold water line be soft water 3 Pull tube to ensure it is secured Copper water supply tubing to oven AWARNING Excessive Weight Hazard supply Use two or more people to move and install oven Failure to do so can result in back or other injury 2 1 Using 2 or more people lift oven partially into cabinet cutout we Ro A using the oven opening as an area to grip P Copper Water supply ges NOTE Push against seal area of oven front frame when hal cold water supply OUT pushing oven into cabinet Do not push against outside edges Filter 4 Route copper tubing through undersink cabinet and oven cabinet cutout NOTE Due to temperatures around oven copper tubing is 2 Push against seal area of front frame to push oven into required cabinet 5 Connect the copper water supply tubing to the oven copper tubing using a 1 4 to 1 4 water supply union not provided r D B C 3 Push oven completely into cabinet and center oven into cabinet cutout 4 Securely fasten oven to cabinet using the 8 14 x 1 screws 2 for single oven 4 for dou2. Excessive Weight Hazard Use two or more people to move and install oven Failure to do so can result in back or other injury 2 To avoid floor damage set the oven onto cardboard prior to installation Do not use handle or any portion of the front frame for lifting 3 Remove the shipping materials and tape from the oven 4 Remove the hardware package from inside the bag containing literature 5 Remove and set aside racks and other parts from inside the oven 3 Grasp the edges of the oven door with both hands and close the oven door until it will no longer close Lift and pull oven door toward you and remove Set the oven door s aside on a covered work surface A Oven door latch in locked B Oven door latch in unlocked position position 6 Move oven and cardboard close to the oven s final location AWARNING Electrical Shock Hazard Disconnect power before servicing Use 8 gauge solid copper wire Electrically ground oven Failure to follow these instructions can result in death fire or electrical shock This oven is manufactured with a neutral white power supply wire and a cabinet connected green or bare ground wire twisted together 1 Disconnect power 2 Feed the flexible conduit from the oven through the opening in the cabinet 3 Remove junction box cover if it is present 4 Install a UL listed or CSA approved conduit connector to the junction box A A UL listed or CSA appr
3. Parts needed m UL listed or CSA approved conduit connector m UL listed wire connectors m Tubing staples retainers m 1 4 O D copper tubing to make water connection NOTE Due to temperatures around oven copper tubing is required m Water connection device to connect 14 O D copper tubing to water source Check local codes for type of connection required m 4 to water supply union between copper tubing from the filter and copper tubing attached to oven Check local codes Check existing electrical supply See Electrical Requirements It is recommended that all electrical connections be made by a licensed qualified electrical installer Make sure you have everything needed for correct installation IMPORTANT Observe all governing codes and ordinances m Cabinet opening dimensions that are shown must be used Given dimensions provide minimum clearance with oven m Recessed installation area must provide complete enclosure around the recessed portion of the oven m Grounded electrical supply is required See Electrical Requirements section m Electrical supply junction box should be located 3 7 6 cm maximum below the support surface when the oven is installed in a wall cabinet A 1 2 5 cm minimum diameter hole should have been drilled in the right rear or left rear corner of the support surface to pass the appliance cable through to the junction box m Oven support surface must be solid l
4. 1 3 8 cm under the filter system for removing the filter cartridge Typical Installation Configuration A Quick connect elbow adapter fitting NOTE For unique installations contact a licensed plumber B Quick connect stem adapter fitting Water supply 2 Connect the copper water supply tubing not provided from oq line to oven the home cold water supply pipe to the quick connect adapter fitting you just installed on the filter inlet yellow side of the water filter E TT 3 Pull tube to ensure it is secured B 1B E water sup y ine to CO oe water supply _ A water supply tubing B O ring C Backstop 2 Attach the supplied water filter mounting ring and screw at the recommended location If you need to release tubing 3 Attach filter to the mounting ring Push in collet to release tubing With collet held in pull tubing o straight out S A Mounting ring and screw D A Collet 1 3 8 cm clearance t Connect to Water Filter Outlet blue Connectie Home Water Supply 1 Attach the supplied to 1 4 stem or to 1 4 elbow quick connect adapter fitting to the blue water filter outlet 1 Make connection to the cold water supply line aii i f connection by pushing the quick connect fitting past the m A leak tight connection to the 1 4 copper tubing must be o ring until you hit the backstop provided 2 Connect another piece of copper water supply tubing to the
5. INSTALLATION INSTRUCTIONS 30 76 2 CM ELECTRIC BUILT IN MICROWAVE OVEN COMBINATION Table of Contents BUILT IN MICROWAVE OVEN COMBINATION SAFETYV 1 INSTALLATION REQUIREMENTS ccscsscssssersensnsenseeseersees 2 Tools and Parts ccceccsseessseeesesseeeecaseeseseessneeaeeseasesenseaseseeeaseneas 2 Built In Microwave Oven Combination Location Requirement c cccccceceeeeeeeeeeeeeeeeeseaeeseeneeeneeesaees 2 Water Filtration System Location Requirements ceeee 3 Water Supply Requirements eseeesseeneeeeeseeeeeeeeseeeeeereenes 3 Electrical Requirements cceecceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeneeeaees 3 INSTALLATION INSTRUCTIONS cccsecstecteestessensersserneerneenseees 4 Prepare Built In Microwave Oven Combination 00 4 Remove Oven DOor eeceeccscccsseeeeeseeseeeeeeseessensseeseesseeenenseeeeseens 4 Make Electrical CONNECTION eee eeceeeceeeeeeeeteeeeaeeeneeeneeeeteeeenees 5 Install Water Filtration System es eseeseeeeeeeeeeeeeeeeeeeeeeeeneeneees 6 Astal QVON ieisssccsaenvezssnscnesesscisceascnanteacceasieasaaveceabessteeaeaesteaecsaadecc ay 7 Complete Installation ceccccesceeeeeeeeeeeeeneeeeeseeeeeeeeeeeeeeeeeeeaeeeees 8 BUILT IN MICROWAVE OVEN COMBINATION SAFETY Your safety and the safety of others are very important We have provided many important safety messages in this manual and on your appliance Always read and obey all safet
6. ble oven provided Insert the screws through holes in mounting rails Do not overtighten screws S SS i e A O A To home water supply B Rear of cabinet cutout B lo C Copper water supply tubing from home water supply D to water supply union not provided E E Oven copper tubing F Oven front 6 Turn on water supply 7 Check all connections for leaks A Mounting rail NOTE No flushing or conditioning of the water filter is required B Insert 8 14 x 1 screw prior to use 5 Onsome models the oven vent is taped to the side of the oven With one 8 14 x screw for each side of the vent fasten vent securely to the oven __ SS SS _ B A 8 14 x Ys screw B Oven vent 10 11 13 Replace oven racks Replace oven door s by inserting ends of hinges into hinge slots in the oven frame Push hinges in as far as they will go and open the oven door You should feel the oven door drop into place Rotate both hinge latches back to the locked position Check that the door is free to open and close If it is not repeat the removal and installation procedures See Remove Oven Door section Reconnect power 12 Display panel will light briefly and PF should appear in the display If display panel does not light please reference the Assistance or Service section of the Use and Care Guide or contact the dealer
7. evel and flush with bottom of cabinet cutout Floor must be able to support a total weight microwave and built in oven of 238 Ibs 108 kg Product Dimensions A 28 e 71 9 cm recessed width B 42 107 5 cm overall height C 29 75 6 cm overall width D 23 58 4 cm max recessed depth E 40 103 5 cm recessed height Cabinet Dimensions e AH gt D M gt ee C E A 30 76 2 cm min cabinet width B 1 2 5 cm top of cutout to bottom of upper cabinet door C 1974 48 9 cm bottom of cutout to floor D 28 14 72 4 cm cutout width E 1 3 8 cm min bottom of cutout to top of cabinet door F 4114 104 8 cm cutout height Cabinet Side View A 24 61 0 cm min cutout depth B 23 58 4 cm recessed oven depth C Oven front D Recessed oven E Cabinet For best results do not install the water filtration system outside or in extreme hot or cold temperatures Temperature of water supply to the water filtration system must be between 40 F 4 C and 100 F 38 C Do not install on hot water supply line Locate the water filtration system near the cold water supply pipe under the kitchen sink to filter cold water It will be necessary to drill a 2 1 3 cm minimum diameter hole in the upper right or left rear corner of the side wall of the cabinet under the sink to route the water supply tubing through to
8. from whom you purchased your oven Check that all parts are now installed If there is an extra part go back through the steps to see which step was skipped Check that you have all of your tools Dispose of recycle all packaging materials For oven use and cleaning read the Use and Care Guide Check Operation of Lower Oven 1 Turn power on 2 From the Main Menu touch STEAM COOK 3 Touch AUTO STEAM 4 Touch VEGETABLES 5 Touch START then OK If oven s does not operate check the following m Household fuse is intact and tight or circuit breaker has not tripped m Electrical supply is connected m See Troubleshooting section in the Use and Care Guide 6 When oven has been on for 10 15 minutes open the oven door look for water vapor escaping and feel for heat If you do not see water vapor or feel heat or if an error code F followed by a number plus E followed by a number appears in the display turn off the oven and contact a qualified technician 7 Touch OFF 8304536A 2007 Whirlpool Corporation All rights reserved Check Operation of Microwave Oven 1 oP ON 7 Fill a microwave safe container with 1 cup 250 mL of water and place container inside microwave oven Close door firmly From the Main Menu touch MANUAL METHOD Touch MANUAL COOK Set microwave oven cook time to 2 00 minutes Touch START If microwave does not operate check the following Ho
9. l serial number rating plate The model serial number rating plate is located at the bottom of the right hand mounting rail See the following Connect directly to the circuit breaker box or fused disconnect through flexible armored or nonmetallic sheathed copper cable with grounding wire See Make illustration Electrical Connection section ay m Flexible conduit from the oven should be connected directly _ to the junction box Cc m Do not cut the conduit The length of conduit provided is for A serviceability of the oven m A UL listed or CSA approved conduit connector must be provided m If the house has aluminum wiring follow the procedure below 4 aS 1 Connect a section of solid copper wire to the pigtail bw a leads 2 Connect the aluminum wiring to the added section of A Model serial number plate copper wire using special connectors and or tools designed and UL listed for joining copper to aluminum Follow the electrical connector manufacturer s recommended procedure Aluminum copper connection must conform with local codes and industry accepted wiring practices IMPORTANT Use both hands to remove oven door s 1 Decide on the final location for the oven Avoid drilling into or 1 Open the oven door severing existing wiring during installation 2 Locate the oven door latches in both corners of the oven door and rotate the latches forward to the unlocked position AWARNING
10. on box using a UL listed wire connector 6 Install junction box cover 3 Wire Cable from Home Power Supply IMPORTANT Use the 3 wire cable from home power supply where local codes permit a 3 wire connection A Cable from home power supply F 4 wire flexible conduit from B Junction box oven C Black wires G Red wires D White wires H UL listed wire connectors E Green or bare ground wire UL listed or CSA approved from oven conduit connector 1 Connect the 2 black wires C together using a UL listed wire connector Connect to Water Filter Inlet yellow 2 Connect the 2 white wires D and the green or bare ground wire of the oven cable using a UL listed wire connector NOTE Use the quick connect stem and or elbow adapter fittings in the combination needed for your installation configuration 3 Connect the 2 red wires G together using a UL listed wire A a connector 1 Attach the supplied to 1 4 stem or to 1 4 elbow quick connect adapter fitting to the yellow water filter inlet connection by pushing the quick connect fitting past the o ring until you hit the backstop 4 Install junction box cover A B Install Water Filter 1 Install the water filter near the cold water supply pipe under the kitchen sink to filter the cold water IMPORTANT Be sure to allow a minimum clearance of
11. oved conduit connector 5 Route the flexible conduit from the oven to the junction box through a UL listed or CSA approved conduit connector 6 Tighten screws on conduit connector 7 See Electrical Connection Options Chart to complete installation for your type of electrical connection Electrical Connection Options Chart If your home has Go to section 4 wire 4 wire Cable from Home Power Supply 3 wire 3 wire Cable from Home Power Supply Yo 1 3 em 4 Wire Cable from Home Power Supply IMPORTANT Use the 4 wire cable from home power supply in the U S where local codes do not allow grounding through neutral New Branch circuit installations 1996 NEC mobile homes and recreational vehicles new construction and in Canada A B E F G C H D I A Cable from home power supply F White wires B Black wires G UL listed wire connectors C Red wires H Green or bare ground wires D 4 wire flexible conduit from I UL listed or CSA approved oven conduit connector E Junction box 1 Connect the 2 black wires B together using a UL listed wire connector 2 Connect the 2 red wires C together using a UL listed wire connector 3 Untwist white wire from green or bare ground wire coming from the oven 4 Connect the 2 white wires F together using a UL listed wire connector 5 Connect the green or bare ground wire H from the oven cable to the green or bare ground wire in the juncti
12. the oven cabinet cutout Another 1 2 1 3 cm minimum diameter hole will need to be drilled at the rear wall in the oven cabinet cutout Depending on your installation configuration more routing holes may be required Typical Installation Configuration NOTE For unique installations contact a licensed plumber m A ae Gee 1 ORN Gat matet F J XY gs Hot Cold Filter og assembly location ee a A cold water supply with water pressure between 30 and 120 psi 207 and 827 kPa is required to operate the steam feature In Massachusetts plumbing code 248 CMR 3 00 and 10 00 must be followed If you have questions about your water pressure call a licensed qualified plumber Reverse Osmosis Water Supply IMPORTANT The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the oven needs to be between 30 and 120 psi 207 and 827 kPa If a reverse osmosis water filtration system is connected to your cold water supply the water pressure to the reverse osmosis system needs to be a minimum of 40 psi 276 kPa If the water pressure to the reverse osmosis system is less than 40 psi 276 kPa m Check to see whether the sediment filter in the reverse osmosis system is blocked Replace the filter if necessary m Allow the storage tank on the reverse osmosis system to refill after heavy usage If you ha
13. usehold fuse is intact and tight or circuit breaker has not tripped Electrical supply is connected See Troubleshooting section in the Use and Care Guide When display reads 1 00 minute open microwave oven door The microwave should stop cooking Close door firmly The interior microwave oven light should turn off Touch CONTINUE to resume preset cycle The microwave oven should begin cooking and the microwave oven interior light should be on Let microwave oven complete cooking time Tones will sound at the end of the cooking time and the microwave oven will shut off Open microwave oven door and slowly remove container Water in container should be hot To set the clock and other oven functions refer to the Use and Care Guide If you need Assistance or Service Please reference the Assistance or Service section of the Use and Care Guide or contact the dealer from whom you purchased your built in oven 5 07 Printed in U S A
14. ve questions about your water pressure call a licensed qualified plumber If codes permit and a separate ground wire is used it is recommended that a qualified electrical installer determine that the ground path and wire gauge are in accordance with local codes Check with a qualified electrical installer if you are not sure the oven is properly grounded This oven must be connected to a grounded metal permanent wiring system Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code ANSI NFPA 70 latest edition or CSA Standards C22 1 94 Canadian Electrical Code Part 1 and C22 2 No O M91 latest edition and all local codes and ordinances A copy of the above code standards can be obtained from National Fire Protection Association One Batterymarch Park Quincy MA 02269 CSA International 8501 East Pleasant Valley Road Cleveland OH 44131 5575 Electrical Connection m Models rated from 7 3 to 9 6 kW at 240 volts 5 5 to 7 2 kW To properly install your oven you must determine the type of at 208 volts require a separate 50 amp circuit Models rated electrical connection you will be using and follow the instructions at 7 2 kW and below at 240 volts 5 4 kW and below at provided for it here 208 volts require a separate 30 amp circuit m Oven must be connected to the proper electrical voltage and m Acircuit breaker is recommended frequency as specified on the mode
15. y messages This is the safety alert symbol This symbol alerts you to potential hazards that can kill or hurt you and others All safety messages will follow the safety alert symbol and either the word DANGER or WARNING These words mean You can be killed or seriously injured if you don t immediately ADANGER follow instructions You can be killed or seriously injured if you don t follow A WARN l N G instructions All safety messages will tell you what the potential hazard is tell you how to reduce the chance of injury and tell you what can happen if the instructions are not followed IMPORTANT Save for local electrical inspector s use 8304536A INSTALLATION REQUIREMENTS Gather the required tools and parts before starting installation Read and follow the instructions provided with any tools listed here Tools needed Adjustable wrench or wrench Phillips screwdriver Flat blade screwdriver Measuring tape Hand or electric drill for wall cabinet installations 1 25 mm drill bit for wall cabinet installations Level Copper tubing cutter Parts supplied 1 box 3 plastic bags One stem to 1 4 quick connect Two elbow to 1 4 quick connects Water filter 10 16 x screw and 1 mounting ring to mount water filter 8 14 x 1 screws single oven 2 double oven 4 Bottom vent Supplied on some models 8 18 x e screws bottom vent Supplied on some models
Download Pdf Manuals
Related Search