Whirlpool FGP335BL2 User's Manual
Contents
1. I D Measurin Niis lt tape orruler pipe w wrench z e gas line shutoff valve e L P resistant pipe joint compound A G A design certified flexible metal connector 4 5 feet Phillips screwdriver a gt flat blade adjustable screwdriver or hammer wrench 5 16 inch nut driver Parts supplied for installation scum at aan anni 2 anti tip brackets 4 screws Gas supply requirements Observe all governing codes and ordinances A WARNING Fire Hazard Range must be connected to a regulated gas supply L P gas supply must Not exceed a pressure of 14 water column This must be checked by a qualified technician before Installing the range Do Not use an open flame to test for loaks from gas connections Now A G A design certifled flexible gas line should be used when codes permit Fallure to follow these Instructions could result In a fire explosion or personal Injury A This installation must conform with local codes and ordinances In the absence of local codes installations must conform with American National Standard National Fuel Gas Code ANSI 2223 1 latest edition B m Input ratings shown on the serial rating plate are for elevations up to 2 000 feet For elevations above 2 000 feet ratings are reduced at a rate of 4 for each 1 000 feet above sea level Cc m This range is design certified by A G A for NATURAL and L P gases with app2. avoid installing cabinet storage above the cooking surface If cabinets are already installed reduce the hazard of reaching over a heated cooking surface by installing a range hood The range hood should extend a minimum of 5 inches out from the bottom front of the cabinets Reaching over a heated cooking surface could result in a serious burn Electrical Shock Hazard It is the customer s responsibility To contact a qualified electrical installer To assure that the electrical installation is adequate and in conformance with National Electrical Code ANSI NFPA 70 latest edition and all local codes and ordinances Failure to do so could result in electrical shock or other personal injury CAUTION Property Damage e Contact a qualified floor covering installer to check that the floor covering can withstand heat at least 90 F above room temperature Use an insulated pad or 1 4 plywood under range if installing range over carpeting Failure to do so may result in damage to floor covering Ke ene provide 0 clearance Batterymarch Park Quincy Massachusetts 02269 American Gas Association 1515 Wilson Boulevard Arlington Virginia 22209 Tools and materials needed for installation e electric drill wood floor 3 16 drill bit concrete ceramic oor 3 16 carbid tipped masonry flare union adapter drill bit for connection to pressure regulator 1727 NPT x 1 2 or 3 4
3. under the maintop Center of range For minimum clearances see Note 30 min h opening width 1 min countertop space to sid wall or other combustible 18 min clearance upper cabinet to countertop f N Centor of marengi Recommended area for through the tloor 79 connection of pipe Do Nor and shutoff valve power cord between Gi inded Mua Dopthwih Mobile Home Installation electrical outlet handie 2779 8 The installation of this range must conform is required to the Manufactured Home Construction See Electrical r and Safety Standards Title 24 CFR Part requirements Cooktop 36 3280 formerly the Federal Standard for Mobile Home Construction and Safety Overall Title 24 HUD Part 280 or when such 46 1 4 standard is not applicable the Standard for Manufactured Home Installation 1982 Manufactured Home Sites Communities Oto WHEE and Setups ANSI Z225 1 NFPA 501A RANGE IS TO BE INSTALLED a baraha latest edition or with local codes MUST BE SEALED side cabinets When this range is installed in a mobile home it must be secured to the floor Cabinet Any method of securing the range is opening adequate as long as it conforms to the Important Observe all Proper gas Width dimensions standards listed above governing codes and supply connection Aes that are shown Copies of the standards listed may be must be available See must be used Given Gas
4. cap over so that the Nat side is up and replace cap and gasket on regulator Cooktop orifice hoods and oven orifice hood need to be loosened 2 to 2 1 2 turns counterclockwise to allow for proper gas flow The flame adjustment for cooktop bumers and oven burner would be the same as described In the installation steps see Panel C Part No 316002955 4372193 Rev B 1994 If range does not operate e Check that the circuit breaker is not tripped or the house fuse blown Check that the power supply cord is plugged into wall receptacle e Check that the gas supply is tumed on NOTE Refer to Use and Care Guide for operating instructions and cleaning instructions For cleaning and maintenance If removing the range is necessary for cleaning or maintenance shut off gas supply to the range Disconnect the gas and electric supply If the gas or electrical supply is inaccessible lift the range slightly at the front and pull the range out away from the wall Pull the range out only as far as necessary to disconnect the gas and electric supply lines Remove the range to complete cleaning or maintenance Move range back into operating position Level the range Connect gas line to range and check for leaks Plug electric power supply cord into outlet Make sure that rear legs are engaged in anti tip bracket WARNING Personal Injury Hazard Product Damage Do Not step lean or sit on the range or th
5. supply requirements obtained from National Fire Protection Assoclation ordinances Check location where range will be installed The range should be located away from strong draft areas such as windows doors and strong heating vents or fans The range should be located for convenient use in the kitchen Recessed installations must provide complete enclosure of the sides and rear of range WARNING If the information in this manual is not followed exactly a fire or explosion may result causing property damage personal injury or death Do Not store or use asoline or other ammable vapors and liquids in the vicinity of this or any other appliance WHAT TO DO IF YOU SMELL GAS e Do Not try to light any appliance Do Not touch any electrical switch Do Not use any phone in your building Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions e If you cannot reach your gas supplier call the fire department Installation and service must be performed by a qualified installer service agency or the gas supplier Panel A oe Both anti tip brackets MUST be instalied Brackets attach to floor at back of range to hold both rear leveling legs For detailed instructions see Panels B and C WARNING Fire Hazard Do Not obstruct the flow of combustion and ventilation air Personal Injury Hazard To eliminate the risk of burns or fire
6. AA WARNING Fire Hazard Do Not use an open flame to test for leaks from gas connections Checking for leaks with a flame may result In a fire or explosion Panel C 1 2 E Use a brush and liquid detergent to test all gas connections for leaks Bubbles around connections will indicate a leak If a leak appears shut off gas valve controls and adjust connections Then check connections again NEVER TEST FOR GAS LEAKS WITH A MATCH OR OTHER FLAME Clean all detergent solution from range 1 3 m Plug power supply cord into grounded outlet 1 4 m Move range into final position Grasp rear of range and carefully try to tip range forward to check that both rear leveling legs are engaged in anti tip brackets 1 5 E Turn power supply on to range Electronic Ignition System initial lighting and gas flame adjustments When the cooktop control knob is turned to LITE position the system creates a spark to light the burner This sparking continues until the control knob is turned to the desired setting When the oven control is turned to the desired setting a glow bar heats up bright orange and Ignites the gas No sparking occurs and the glow bar remains on while the burner operates 1 6 m Check the operation of the cooktop burners Push in and turn each control knob to LITE position The flame should light within 4 seconds Do Not leave the knob In the LITE position after burner lights 1 T m A
7. Installation Instructions WARNING e ALL RANGES CAN TIP e INJURY TO PERSONS COULD RESULT e INSTALL ANTI TIP DEVICE PACKED WITH RANGE SEE INSTALLATION INSTRUCTIONS IMPORTANT Read and save these instructions IMPORTANT Installer Leave Installation Instructions and anii tip bracket template with the homeowner Homeowner Keep Installation Instructions and anti tip bracket template for future reference Save Installation Instructions for local electrical inspector s use Part No 316002955 4372193 Rev B 30 Freestanding ez Range Ya Electrical and gas dimensions Shaded area is recommended area for 120v outlet on rear wall and area for through the wall Note 30 min when bottom of wood or metal cabinet is protected by not less than 1 4 flame retardant millboard covered with not less than No 28 MSG sheet steel 0 015 stainless steel 0 024 aluminum or 0 020 copper connection of gas 36 min clearance between the top pipe and shuto of the cooking platform and the valve bottom of an unprotected wood or metal cabinet Before you start Proper installation is your responsibility A qualified technician must install this range Make sure you have everything necessary for correct installation It is the responsibility of the installer to comply with the installation clearances specified on the serial rating plate The serial rating plate is located
8. e door or drawers of the range Fallure to follow this Instruction could result in personal Injury and or product damage Benton Harbor Michigan 49022 If you need assistance Check your Use and Care Guide for a toll free number to call or call the dealer from whom you purchased this appliance The dealer is listed in the Yellow Pages of your phone directory under Appliances Household Major Service amp Repair When you call you will need the range model number and serial number Both numbers can be found on the serial rating plate located under the maintop Printed on recycled paper 10 post consumer waste 50 recovered materials Printed in U S A
9. ets Remove and reposition brackets so leveling legs will fit properly under end flanges of brackets 8 E Place rack in oven Place level on rack first side to side then front to back to check that range is level If range is not level adjust legs up or down If needed pull range forward until rear leveling legs can be adjusted Push range back into position and check that range is level Note Oven must be level for satisfactory baking conditions WARNING Firo Hazard Do Not make connection too tight The regulator Is dle cast Overtightening may crack the regulator resulting In a gas leak and possible flre or explosion All connections must be wrench tightened manual shutoff flexible connector valve Ghee cia messi pressure 1 2 flare union adapters regulator 9 m Pull range forward to make gas connections Assemble the flexible connector from the gas supply pipe to the pressure regulator located on the lower right hand side on the back of the range in this order shutoff valve 1 2 flare union adapter flexible connector 1 2 flare union adapter Seal all openings in floor or wall wherever range is installed 1 0 E Use pipe joint compound made for use with Natural and L P gas to seal all gas connections If flexible connectors are used be certain connector is not kinked 1 1 E Open the shutoff valve in the gas supply line Wait a few minutes for gas to move through the gas line
10. fter burner lights turn ue control knob to HI position Check each cooktop bumer for proper flame The small inner cone should have a very distinct blue flame approximately 1 2 long The outer cone is not as distinct as the inner cone 1 8 If burners need adjusting for proper flame remove burner grates and carefully lift up the maintop Adjust the air shutter to the widest opening that wil produce a sharp blue flame that does not lift or blow off of the burner Repeat as necessary with each burner 1 9 m Push in and turn the control knob to the LITE position and then to the LO position The low flame should be a minimum steady blue flame To adjust the burner remove the control knob and turn the adjustment screw in the center of the valve stem Check the adjustment by turning the control knob from HI to LO several times The bumer is properly adjusted when the low flame remains steady and the burner does not go out Check each burner 20 m Remove oven rack Remove oven screws at rear of oven bottom Pull oven bottom rear up and remove front of oven bottom from oven front Remove oven bottom Remove burner baffle Check the operation of the oven bummer wea AP alr adjustment Push in and turn temperature control knob counterclockwise to 300 F The oven burner should light In 50 60 seconds This delay is normal The oven safety valve requires a certain time before it will o
11. g range in a mobile home you MUST secure range to floor Any method of securing range is adequate as long as it conforms to the standards listed in the Mobile Home Installation instructions Panel A 4 E Use a pencil to mark the mounting screw hole locations on the floor Remove template CAUTION Property Damage Contact a quallfled Installer for the best procedure fo drill mounting holes through your type of floor covering Before moving range across floor check that range Is on shipping base or silde range onto cardboard or hardboard Fallure to follow these Instructions may result In damage to floor covering 5 E To mount antl tip bracket to wood floor drill a 3 16 hole 1 2 deep at each mounting screw location To mount antl tip bracket to concrete or ceramic floor use a masonry drill bit to drill a 3 16 hole 1 2 deep at each mounting screw location Numbers correspond to steps 6 m Place anti tip bracket on floor with turned up flange facing the front Line up holes in anti tip bracket with holes drilled in floor Use screws to attach bracket to floor Repeat with right anti tip bracket turned up flange 7 B Remove shipping base cardboard or hardboard from under range Remove storage drawer Carefully move range into position Grasp rear of range and carefully try fo tip range forward If range tips forward leveling legs are NOT properly engaged in anti tip brack
12. ne grounding type power wall receptacle supply cord grounding prong Now start With range in kitchen 1 m Remove shipping materials tape and protective film from range Keep cardboard shipping base under range Remove oven racks and shipping materials from inside oven 2 Adjust leveling legs so there is at least 3 1 8 inch between bottom of range and leveling legs min WARNING Personal Injury Hazard e To reduce the risk of tipping of the appliance the appliance must be secured by properly Installed floor mounted antl tip brackets supplled with the range Save these Installation Instructions If range Is moved to a new location the antl tlp brackets must be removed and reinstalled In the new location Electrical Shock Hazard Take special care when dilliing holes Into the floor Electrical wires or plumbing may be located beneath floor Locate the electrical circults that could be affected by the Installation of these brackets and turn off power to these clrcults Fallure to follow these Instructions may result in electrical shock or other personal Injury back edge of range or rear wall or 2 1 4 aee Pa LE anti tip brackets range side panel iocation 3 m Unfold paper template and place it flat on the floor with the back and side edges positioned exactly where the back and sides of range will be located when installed If installin
13. pen and allow gas to flow CAUTION Product Damage Do Not Insert any object Into the openings of the protective shield that surrounds the ignitor Do Not clean the area Fallure to follow these Instructions could result In product damage for proper flame This flame should have a 1 long inner cone of bluish green with an outer mantle of dark blue and should be clean and soft in character No yellow tips blowing or lifting of flame should occur 22 E If oven flame needs to be adjusted air locate the air shutter near shutter the center rear of the oven burner Loosen the lock lock screw and adjust the air shutter until the proper flame appears hood Tighten screw 23 Replace the oven burner baffle oven bottom oven racks and broiler drawer 2 1 mw Check the oven bummer To get the most efficient use from your new range read your Use and Care Guide Keep installation Instructions and Guide close to the range for easy reference Gas conversion The serial rating plate located under the maintop specifies the type of gas this range was set to use Conversion should be done by a qualified installer Natural to L P gas A Convert the pressure regulator Do Not remove the pressure regulator cap hollow end solid end towards towards regulator for regulator for natural gas L P gas spring 1 Unscrew the cap from the pressure regulator Be sure spring stay
14. r personal Injury If codes permit and a separate grounding wire is used it is recommended that a qualified electrician determine that the grounding path is adequate A 120 volt 60 Hz AC only 15 ampere fused electrical supply is required A time delay fuse or circuit breaker is recommended It is recommended that a separate circuit serving only this appliance be provided Electronic ignition systems operate within wide voltage limits but proper grounding and polarity are necessary In addition to checking that the outlet provides 120 volt power and is correctly grounded the outlet must be checked by a qualified electrician to see if it is wired with correct polarity The wiring diagram is found on a separate sheet in the literature package The wiring diagram can also be found on the back of the range Recommended grounding method For personal safety this appliance is equipped with a power supply cord having a 3 prong grounding plug To minimize possible shock hazard the cord must be plugged into a mating 3 prong grounding type wall receptacle grounded in accordance with the National Electrical Code ANSI NFPA 70 latest edition and all local codes and ordinances See Figure 1 Ifa mating wall receptacle is not available it is the personal responsibility and obligation of the customer to have a properly grounded 3 prong wall receptacle installed by a qualified electrician 3 pron grounding plug po
15. ropriate conversion The serial rating plate located under the cooktop has information for the type of gas that can be used If this information does not agree with the type of gas available check with the local gas supplier See Panel C and back cover for gas conversion instructions D m Provide a gas supply line of 3 4 rigid pipe to the range location A smaller size pipe on long runs may result in insufficient gas supply Pipe joint compounds made for use with L P gas must be used With L P gas piping or tubing size can be 1 2 minimum L P gas suppliers usually determine the size and materials used on the system E m Ifiocal n codes permit a new A G A design certified 4 5 foot long 1 2 or 3 4 1 D flexible metal appliance connector is recommended for connecting this range to the gas supply line Do Not kink or damage the flexible tubing when moving the range A 1 2 inch male pipe thread is needed for connection to pressure regulator female pipe threads shutoff valve open position Be oe m The supply line shall be equipped with an approved shutoff valve This valve should be located in the same room as the range and should be in a location that allows ease of opening and closing Do Not block access to shutoff valve G m If rigid pipe is used as a gas supply line a combination of pipe fittings must be used to obtain an in line connection to the range All strains must be removed from
16. s in place 2 Tum the cap over so the hollow end faces outward 3 Replace the cap of the regulator The letters L P should be visible on exposed end of the cap B a Convert surface burner valves cooktop shown in raised position 4 surface bumer hoods pin L P GAS decreases gas decreases flame size NAT GAS increases gas increases flame size preset at factory for natural gas 1 Lift and lock cooktop in up position 2 Use 1 2 wrench to turn hood clockwise until snug approximately 2 1 2 tums Do Not overtighten Cc a Convert oven burner 1 Remove oven bottom hold down screws at rear of oven bottom Pull up at rear and remove front of oven bottom from oven front frame Pull the oven bottom straight out of the oven Remove burmer baffle 2 Use 1 2 wrench to turn the hood clockwise approximately 2 1 2 turns until snug against the pin Do Not overtighten 3 Turn thermostat control knob to 300 F The oven burner flame should be steady and approximately 1 long with no yellow or orange tips air shutter 4 if air shutter needs adjusting loosen air shutter set screw and adjust to obtain proper flame This will normally be completely open for L P gas Tighten air shutter set screw 5 Replace oven baffle and oven bottom L P to Natural gas Converting to natural gas should be done by a qualified Installer Use a wrench to remove cap from pressure regulator Tum
17. the supply and fuel lines so range will be level and in line fA m The inlet pressure must be a minimum of 1 inch above the set pressure of the regulator a maximum of 14 inches total inlet pressure Set Pressure Natural Gas 4 Inches L P Gas 10 Inches I E Line pressure testing Testing above 1 2 psi gauge The range and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures greater than 1 2 psig 3 5 kPa Panel B Testing at 1 2 psl gauge The range must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1 2 psig 3 5 kPa Electrical Requirements AA WARNING Electrical Shock Hazard Electrical ground Is required on this appliance Do Not ground to a gas pipe Do Not modify the power supply cord plug If It does not fit the outlet have a proper outlet Installed by a qualified electrician Do Not have a fuse In the neutral or grounding circult A fuse In the neutral or grounding clircult could result in an electrical shock Do Not use an extension cord with this appllance Check with a qualified electrician if you are In doubt as to whether the appllance Is properly grounded Fallure to follow these Instructions could result In a fire electrical shock or othe
Download Pdf Manuals
Related Search