Well Traveled Living 11201 User's Manual
Contents
1. STORAGE Between uses Turnthe control knob to OFF position TurnLP cylinderto OFF position Store heater upright in an area sheltered from direct contact with NOTE inclement weather such as rain sleet hail snow dust and debris s Ifdesired cover heater to protect exterior surfaces and to help prevent debris in air passages Wait until heater is cool before covering During periods of extended inactivity or when transporting Turnthe control knob to OFF position Disconnect LP Cylinder and move to a secure well ventilated location outdoors Do NOT store in a location that will exceed 125 degrees F The propane cylinder must be stored outdoors in well ventilated area and it must be out of reach of children and not in a building garage or any other enclosed area Store heater upright in an area sheltered from direct contact with inclement weather such as rain sleet hail snow dust and debris If desired cover heater to protect exterior surfaces and to help prevent debris in air passages Well Traveled 16 TROUBLESHOOTING PROBLEM PROBABLE CAUSE SOLUTION Pilot will not light Gas valve may be OFF Turn the gas valve ON Fuel Tank empty Refill LP gas tank Orifice blocked Clean or replace orifice Air in supply system Purge air from lines Loose connection Check all fittings Pilot will not stay on Debris around pilot Clean dirty area Loose connection T2. Patio Heater Owner s Manual Deluxe Models FOR YOUR SAFETY If you smell gas 1 Shutoff gas to the appliance 2 Extinguish any open flame 3 Ifodor continues immediately call gas supplier WTERTE j FOR YOUR SAFETY Do not store or use gasoline or other c US flammable vapors or liquids in the vicinity of this or any other appliance LISTED CAUTION Retain the instructions for future use Important Notice Do NOT return to place of purchase Please contact our Toll Free Hotline for customer service amp warranty issues 1 866 985 7877 1 866 WTL SUPP TA Wy TRAVELED LIVING Well Traveled Living 716 South 8th Street Amelia Island FL32034 USA Warning For OUTDOOR USE only N 5 AN DANGER TO ND PARTS NEEDED FOR ASSEMBLY CARBON MONOXIDE HAZARD This appliance can produce carbon monoxide which has no odor Using itin an enclosed space can kill you Never use this appliance in an enclosed space such as a camper tent car or home WARNING Improper installation adjustment alteration services or maintenance can cause injury death or property damage Read the installation operating and maintenance instructions thoroughly before installing or servicing this equipment WARNING For outdoor use only Cylinders to be used must be constructed and marked in accordance with US DOT specifications Storage i
3. ES COSTS OR DAMAGES OR IF SUCH LOSSES COSTS OR DAMAGES ARE FORESEEABLE IN NO EVENT WILL WELL TRAVELED LIVING OR ITS OFFICERS DIRECTORS OR AGENTS BE LIABLE FOR ANY DIRECT LOSSES COSTS OR DAMAGES THAT EXCEED THE PURCHASE PRICE OF THE PRODUCT SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO THE PURCHASER This limited warranty gives you specific legal rights and you may also have other rights which vary from jurisdiction to jurisdiction The provisions of the United Nations Convention on Contracts for the Sales of Goods shall not apply to this limited warranty or the sale of products covered by this limited warranty IMPORTANT NOTICE Do NOT return to place of purchase For customer service and warranty issues contact our Customer Service Center at 866 985 7877 OR Email cservice welltraveled net Customer Service Hours Mon Fri 9 00 a m 6 00 p m EST ire Sense and Well Traveled Living are registered trademarks of Well Traveled Imports Inc All assembly instruction presentations are the property of Wel Fire Sense and Well Traveled Living istered trademarks of Well Traveled Inc All bly i i i h f Well Traveled Imports Inc and are protected by U S copyrights and trademarks All rights reserved
4. IGNITE thento PILOT position this will light the pilot If needed keep depressing and turning control knob counterclockwise until the pilot lights You will hear 2 clicking noises 4 Once the pilot is lit continue to keep the control knob depressed for at least 30 seconds After 30 seconds release control knob 5 If pilot does not stay lit repeat steps 3 and 4 6 If pilot still does not stay lit then a Push in gas control knob and turn counterclockwise to IGNITE then to PILOT b Keep depressing the control knob Put long stem lighter into the Ignition Hole on the emitter screen to light the pilot c Repeat step 4 7 Push in and turn control knob counterclockwise to LOW position release knob then turn to low If you want a higher temperature push in the control knob and turn counterclockwise to the HIGH position Note The flame pattern at the emitter grid should be visually checked whenever heater is operated Normally the burner flame is blue but a little yellow flame is acceptable If flames extend beyond the emitter grid or there are black spots that have accumulated on the emitter grid or reflector immediately turn off the patio heater The heater should not be operated again until it has been serviced and repaired by a qualified gas technician If you experience any ignition problem turn off the heater and gas supply and consult Troubleshooting on page 17 12 WARNING FOR YOUR SAFETY If at an
5. Wait five 5 minutes before attempting to relight pilot 3 Repeat steps beginning with step 2 on page 12 Before Leaving 1 Turn the control knob to OFF position and Turn LP cylinder to OFF position 2 Never leave the patio heater unattended while in use SHUT DOWN INSTRUCTIONS 1 Push in and turn control knob clockwise to OFF position 2 Turn L P tank gas valve clockwise to OFF position when heater is notin use Note After use some discoloration of the emitter screen is normal The Event of Gas Leakage 1 Turn the control knob to OFF position 2 Turn LP cylinder to OFF position 3 Wait 5 minutes to allow gas to dissipate 4 lf odor continues immediately call gas supplier WARNING Heater will be hot after use Handle with extreme care Well Traveled 13 LOCATING HEADER FOR USE BE CAREFUL WHEN CERTAIN MATERIALS OR ITEMS ARE LEFT ABOVE BESIDE OR UNDER THIS HEATERWHILE IN USE THEY WILL BE SUBJECT TO RADIANT HEAT AND COULD BE SERIOUSLY DAMAGED This heater is primarily used for the heating of outdoor patios decks spas pool and open working areas Always make sure that adequate fresh air ventilation is provided Follow the spacing tolerances shown in Figure 1 The minimum clearances shown in Figure 1 must be maintained at all times The installation must conform to local codes or in the absence of local codes with the standard for the storage and handling of liqu
6. activities on a regular basis e Keep exterior surfaces clean e Use warm soapy water for cleaning Never use flammable or corrosive cleaning agents e While washing your unit be sure to keep the area around the burner and pilot assembly dry at all times If the gas control is exposed to water in any way do NOT try to use it It must be replaced e Air flow must be unobstructed Keep controls burner and circulating air passageways clean Signs of possible blockage include e Gas odor with extreme yellow tipping of flame e Heater does NOT reach the desired temperature e Heater glow is excessively uneven e Heater makes popping noises e Spiders and insects can nest in burner or orifices This dangerous condition can damage heater and render it unsafe for use Clean burner holes by using a heavy duty pipe cleaner Compressed air may help clear away smaller particles e Carbon deposits may create a fire hazard Clean dome and emitter screen with warm soapy water if any carbon deposits develop 15 Visually check Yellow Tip Primarily Blue Flame WARNING FORYOURSAFETY DO NOT touch or move heater for at least 45 minutes after use Allow all burner elements to cool before touching NOTE Ina salt air environment such as near an ocean corrosion occurs more quickly than normal Frequently check for corroded areas and repair them promptly Well Traveled MAINTENANCE E
7. are stored Prior to use check for damaged parts such as hoses regulators pilot or burner Warning This appliance requires a gas hose and regulator Regularly check the gas hose and if necessary replace the gas hose DISCONNECT LPG bottle before moving the heater Do not attempt to alter unitin any manner EXAMPLE using the heater without the top canopy reflector or radiant screen Do not shorten the burner post assembly The appliance shall not be used in basements or below ground level Itmust always be placed on a solid and level surface Always ensure there is ample fresh air ventilation For outdoor use ONLY Maintain at least 24 side clearance and 36 top clearance to combustible materials amp surfaces Never replace or substitute the regulator with any regulator other than the factory suggested replacement Do not clean the heater with cleaners that are combustible or corrosive Do not paint radiant screen control panel or top canopy reflector All leak tests should be done with a soapy solution NEVER USE AN OPEN FLAME TO CHECK FOR LEAKS The LP gas cylinder should be turned off when the heater is not in use At least once a year the unit should be inspected for the presence of spiders spider webs or other insects Check the heater immediately if any of the following exist 1 The smell of gas in conjunction with extreme yellow colored tips of the burner flames 2 The heater does not reach tem
8. id petroleum gases ANSI NFPA 58 1986 or most recent addition For Canada with the current CAN1 B149 This heater must be placed on level firm ground Never operate in an explosive atmosphere Keep away from areas where gasoline or other flammable liquids or vapors are stored or used Figure 1 Well Traveled Check Your Hose Assembly The installation of fixed appliances shall only be carried out by competent persons and be in accordance with the relevant Codes of Practice Warning This appliance requires a gas hose and regulator check with your gas supplier and or product supplier Regularly check the gas hose and if necessary replace the gas hose Prior to use check for damaged parts such as hoses regulators pilot or burner Never replace or substitute the regulator with any regulator other than the factory suggested replacement Check Your Flame The flame pattern atthe Emitter Screen should be Visually Checked whenever heater is operated Normally the burner flame is blue but little yellow flame is acceptable If flames extend beyond the emitter grid or there are black spots that have accumulated on the emitter grid or reflector immediately turn off the patio heater The heater should not be operated again until it has been serviced and repaired by a qualified gas technician Clean To enjoy years of outstanding performance from your heater make sure you perform the following maintenance
9. ighten connection Thermocouple bad Replace thermocouple Gas leak in line Check connections Lack of fuel pressure Fuel tank is near empty Burner will not light Pressure is low Fuel tank is near empty Orifice blocked Remove clean and replace Control valve not ON Turn valve to ON Thermocouple bad Replace thermocouple Pilot light assembly bent Place pilot in proper or not in correct location position and retry Well Traveled Distributed By Well Traveled Living 716 S 8 Street Amelia Island FL 32034 Toll Free 866 WTL SUPP Web www wtliving com Email cservice welltraveled net 1 YEAR LIMITED WARRANTY Customers in the Continental US All components are warranted for a period of 1 year after date of purchase by the original owner against defects in materials and workmanship under normal use This warranty does NOT cover normal wear and weathering assembly and or maintenance OR use in a commercial application At Well Traveled Living s sole discretion products under warranty will be repaired and or replaced at no charge to the customer Any returns sent back to Well Traveled Living must be sent via prepaid freight and in the original retail packaging For warranty service contact Well Traveled Living at the address phone numbers or internet site and email listed in this owners manual Be sure to have your sales receipt date of purchase and catalogue model numbers available when calling All warran
10. ndoors is permissible only if the cylinder is removed The unit should be secured or moved indoors if winds exceed 19 5 mph Note 20 Ib LPG Tank is not supplied TOOLS NEEDED Adjustable Opening Wrench 8 Long Philips Head Screwdriver Leak Detection Solution Instructions on how to make solution are included in Step 10 For questions replacement parts service help or other assistance please call Well Traveled Living s Service Hotline at 1 866 985 7877 1 866 WTL SUPP or email cservice welltraveled net Well Traveled 066690606868 6600900000 1 Center Reflector Cap 3 Reflector Cap 1 Head Assembly 1 Gas Hose 1 Upper Post 1 Lower Post 1 Cylinder Cover 3 Post Mounts 1 Cylinder Base 1 Post Support 3 M8 Screw Cap 6 M8 Washers 9 M6 Screw Cap 9 M6X8 Bolts 4 M5X10 Bolts 4 M6X10 Bolts 6 M6X18 Bolts 6 M6 Screw Cap 1 Regulator 3 M8X90 Double Pointed Bolts 3 M8X16 Bolts a o0 m 90 gt Well Traveled PRECAUTIO NOTE PLEASE READ THE FOLLOWING SAFETY RULES WARNING This appliance must only be used outdoors Using this product in an enclosed area may cause injury death or property damage Read the instructions before use This appliance must be installed in accordance with such regulations as are in force Do not use the heater in an explosive atmosphere Keep the heater away from areas where gasoline or other flammable liquids or vapors
11. nted bolts Place remaining 3pcs of M8 washers on top of ends of double pointed bolts secure with 3pcs M8 wing nuts Well Traveled Step 9 Connect Gas Hose to Cylinder Not supplied Attach Gas hose to regulator with 3 8 Inch Open End Wrench and Adjustable Wrench Attach regulator to cylinder Tighten securely Move cylinder to the plate of base assembly Step 10 Check for Leak Your Patio Heater has been checked at the factory for all possible connection leaks To check the connection of the gas hose regulator cylinder 1 Make leak solution by mixing 1part liquid dish soap and 3 parts water 2 Spoon several drops or use squirt bottle of the solution onto the gas hose regulator and regulator cylinder connection 3 Inspect the connections and look for bubbles 4 If no bubbles appear the connection is safe 5 If bubbles appear there is aleak Loosen and re tighten this connection 6 If leak continues call a qualified service person 7 Use of teflon plumber s tape on threads of gas connections is recommended Step 9 Step 10 Well Traveled Step11 Lower Cylinder Cover onto Cylinder Base Lower the cylinder cover onto the cylinder base Step 12 Disconnect Cylinder When Storing orTransporting Turnoff the heater Turnoff the valve of the cylinder Loosen the screw of cylinderand regulator Disconnect the cylinder from
12. onsibility of the installer Step1 Attach post mounts to cylinder base Place the post mounts on the top of cylinder base and connect them using 3pcs M8 X 16 bolts Step 1 Well Traveled ASSEMBLY Step 2 Attach post support to post mounts Place the post support on the top of post Step2 mounts using 6pcs M6 X 18 screw bolts 6pcs M6 screw caps Step3 Attach lower post to base assembly Attach the lower post to the post mounts using 4pcs M6 X 10 bolts Well Traveled Step 4 Attach upper post to lower post Screw the upper post to the lower post as illustrated by turning in a clockwise direction until securely tightened Step 5 Attach cylinder cover to post mounts Step5 Attach cylinder cover to the post mounts Well Traveled ASSEMBLY Step 6 Attach double pointed bolts to head assembly Attach M8 X 90 double pointed bolts 3pcs to head assembly Step 7 Attach the gas hose to head assembly Route the gas hose up through the post and out of top then connect to the head assembly by turning in a clockwise direction Finally Connect the the head assembly with post with 4pcs M5 X 10 bolts Step6 Well Traveled Step 8 Attach the reflector to the top of head assembly Place 3pcs M8 washers on the top of 3pcs double pointed bolts Place assembled re flector on top of double poi
13. perature 3 The burner makes popping noises during use a slight popping noises is normal when the burner is extinguished after using The propane hose with regulator assembly shall be located out of pathways where people may trip over it or in areas where the hose will not be subject to accidental damage Children and adults should be aware of the hazards of high surface temperature and shall stay away to avoid clothing burn or ignition Young children should be carefully supervised when they are in the area of the heater Clothing or other flammable material should not be hung from the heater or placed on or near the heater Any guard or other protective device removed for servicing the heater must be replaced prior to operating the heater Installation and repair should be done by a qualified service person The heater should be inspected before use and cleaning may be required at least once a year or as necessary It is imperative that control compartment burner and circulating air passageways of the heater be kept clean Keep the appliance area clear of combustible materials such as gasoline and other flammable vapors and liquids Do not obstruct the flow of combustion and ventilation air Keep the ventilation opening of the cylinder enclosure free and clear of debris Save these instructions Retain in a safe place for future reference Well Traveled ASSEMBLY Warning Proper assembly is the resp
14. regulator 1 2 3 Lift the cylinder cover above the post mounts 4 5 Step 11 1 Well Traveled The installation must conform with local codes or in the absence of local codes with the most current version of the National Fuel Gas Code ANSI Z223 1 OPERATION WARNING Do NOT attemptto operate heater until you have read and understood all precautions Failure to do so can resultin serious personal injury death and or property damage Before Turning Gas Supply ON Your heater was designed and approved for OUTDOOR USE ONLY Do NOT use it inside a building or any other enclosed area Make sure surrounding areas are free of combustible materials gasoline and other flammable vapors or liquids Ensure that there is no obstruction to air ventilation Be sure all gas connections are tight and there are no leaks Be sure the access panel is clear of debris Be sure any component removed during assembly or servicing is replaced and fastened prior to starting Before Lighting Heater should be thoroughly inspected before each use and by a qualified service person at least annually If relighting a hot heater always wait at least 5 minutes Our heater is tested for quality assurance Ignition attempts should succeed 8 out of 10 attempts LIGHTING INSTRUCTIONS 1 Turn the control knob to OFF position 2 Fully open gas valve 3 Push in gas control knob and turn counterclockwise to
15. ty service will be coordinated by the Well Traveled Living s Amelia Island Florida service center This warranty is extended only to the original purchaser Proof of purchase will be required before warranty service is rendered The sales receipt is the only valid proof of purchase This warranty only covers failures due to defects in materials or workmanship which occur during normal use Failures and or damage which result from accident negligence misuse abuse neglect mishandling alteration or modification failure to maintain improper assembly or maintenance service by unauthorized agency or use of unauthorized components or damage that is attributable to acts of God are NOT covered THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED ABOVE PURCHASER ASSUMES ALL RISKS IN THE ASSEMBLY AND OPERATION OF THIS UNIT FAILURE TO FOLLOW WARNINGS AND OPERATIONAL INSTRUCTIONS CONTAINED IN THIS MANUAL CAN RESULT IN SEVERE PROPERTY DAMAGE AND OR PERSONAL INJURY IN NO EVENT WILL WELL TRAVELED LIVING OR ITS DIRECTORS OFFICERS OR AGENTS BE LIABLE TO THE PURCHASER OR ANY THIRD PARTY WHETHER IN CONTRACT IN TORT OR ON ANY OTHER BASIS FOR ANY INDIRECT SPECIAL PUNITIVE EXEMPLARY CONSEQUENTIAL OR INCIDENTAL LOSS COST OR DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE SALE MAINTENANCE USE OR INABILITY TO USE THE PRODUCT EVEN IF WELL TRAVELED LIVING OR ITS DIRECTORS OFFICERS OR AGENTS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSS
16. y time you are unable to light burner and smell gas wait 5 minutes to allow gas to dissipate before attempting to light heater If after 1 minute you are unable to light burner wait 5 minutes and allow flammable vapors to dissipate before attempting to light heater again WARNING FOR YOUR SAFETY Do NOT touch or move heater for at least 45 minutes after use Allow emitter and dome to cool before touching Well Traveled OPERATION CAUTION Avoid inhaling fumes emitted from the heater s first use Smoke and odor from the burning of oils used in manufacturing will appear Both smoke and odor will dissipate after approximately 30 minutes The heater should NOT produce thick black smoke NOTE The burner may be noisy when initially turned on To eliminate excessive noise from the burner turn the Control Knob to the LOW position Then turn the knob to the level of heat desired When heater is ON Emitter screen will become bright red due to intense heat The color is more visible at night Burner will display tongues of blue flame These flames should not be yellow or produce thick black smoke indicating an obstruction of airflow through the burners Operation Pressure Checked If the flame is very small this is because the supply pressure is not enough To Light 1 Turn the control knob to OFF position 2
Download Pdf Manuals
Related Search