Weider M139-2 User's Manual
Contents
1. is to be assembled Assemble the 5 16 X 4 HEX HEAD BOLT 80 into the large hole at the very end of one of the LONG ANGLE IRONS 10 and into one METAL FERRULE 81 The Hex Head Bolt will then go all the way through the Main Frame As It comes out of the Main Frame on the other side place another METAL FERRULE 81 onto the bolt and push the bolt the rest of the way through into the opposite LONG ANGLE IRON 10 Secure with 5 16 NYLON LOCK NUT 55 TIGHTEN ALL THE MACHINE SCREWS ON THE BACK OF THE BACKREST AT THIS TIME Align the SEAT 9 onto the seat bracket on MAIN FRAME 3 and attach with 1 4 3 4 MACHINE SCREWS 59 WEIDER HEALTH and FITNESS PAGE STEP 3 LEC CURL ASSEMBLY WEIGHT 12 is 1 diameter 13 3 4 long and has hole near one end Assemble the WEIGHT PIN 12 in the angled hole in the front of LEG CURL 11 Secure with 5 16 X 2 HEAD BOLT 53 and 5 16 NYLON LOCK NUT 55 Press 1 ROUND INSERT CAP 72 into the front end of the Weight Pin and place the 1 ROUND COVER CAP WITH THE 15 DEGREE END 73 on the back end The 15 degree side of the cap should be oriented to the angle of the Weight Pin Press 1 1 2 SQUARE PLASTIC 71 into forward end of LEG CURL 11 Position the Leg Curl between the Leg Curl Brackets on MAIN FRAME 3 and secure with 3 8 X 2 1 2 HEX HEAD BOLT 56 and 3 8 NYLON LOCK NUT 57 This bolt should be tightened but be ca2. 8070 F25 AA 8004 F 25 AA 8112 F 25 AA 8091 F 25 AA 8128 F 25 WW 7038 F25 74 75 78 STOPPER 5 16 X 1 3 4 HEX HEAD BOLT 5 16 X 4 HEX HEAD BOLT 5942 04 25 5943 04 25 2 aou 1 5 WEIDER HEALTH and FITNESS PAGE STEP 1 FRAME ASSEMBLY Press 2 SQUARE PLASTIC CAPS 70 into bottom of UPRIGHT 1 Align BRACKETS 2 to UPRIGHT 1 and secure with two each 5 16 X 2 1 2 HEX HEAD BOLTS 51 and 5 16 NYLON LOCK NUTS 55 Look carefully at FRONT SUPPORT 4 One side of the Front Support has the holes dimpled in this is the side of the part that must be faced to the floor Bolt MAIN FRAME 3 front bracket to FRONT SUPPORT 4 using 5 16 X 1 3 4 HEX HEAD BOLTS 79 and 5 16 NYLON LOCK NUTS 55 Press 1 1 2 SQUARE PLASTIC CAPS 71 into each end of FRONT SUPPORT 4 Assemble ANGLE BRACKET 19 under MAIN FRAME 3 in corner where the horizontal and vertical member meet Use 1 4 X 2 MACHINE SCREWS 58 and 1 4 NYLON LOCK NUTS 60 to secure the bracket The 1 4 X 2 MACHINE SCREWS 58 should be assembled by first inserting through the Frame member then the Angle Bracket and then fasten with 1 4 Nylon Lock Nut a Assemble rear U Bracket of MAIN FRAME 3 over cross member of UPRIGHT 1 and secure using 5 16
3. D LAY OUT ALL THE PARTS SO THEY BE EASILY IDENTIFIED IS EXTREMELY HELPFUL IF THE CONTENTS OF THE HARDWARE BAG ARE EMPTIED OUT AND LIKE PARTS GROUPED TOGETHER 5 16 X 3 HEX HEAD BOLTS TOGETHER ETC A HANDY PLACE TO HOLD THE HARDWARE MIGHT TO USE THE INSIDE OF THE CARTON TOP AFTER GROUPING PARTS AGAINST THE PARTS LIST TO IDENTIFY PARTS AND SIZES WRITE THE SIZE AND PART NAME BESIDE EACH PART SO YOU KNOW EXACTLY WHICH PART TO GO TO FOR A PARTICULAR ITEM THE ASSEMBLY INSTRUCTIONS HAVE BEEN WRITTEN USING CHECK AS YOU GO ASSEMBLY METHOD BY CHECKING THE BOXES AS YOU GO IT IS VERY EASY TO FOLLOW ALONG THE ASSEMBLY WITHOUT REREADING TO FIND YOUR PLACE IN THE ASSEMBLY YOU WILL ALSO NOTICE THAT AT THE BEGINNING OF EACH ASSEMBLY STEP THERE 1 A HARDWARE LIST SHOWING THE QUANTITY AND DESCRIPTION OF THE HARDWARE REQUIRED DO ALL ASSEMBLIES IN THAT STEP BY PRE SELECTING THE HARDWARE FOR EACH STEP YOU WILL SAVE TIME AND CONFUSION Z TAKE NOTE OF ANY SPECIAL WARNINGS CAUTIONS NOTES OR NOTICES LAY OUT UNASSEMBLED PARTS FAMILIARIZE YOURSELF WITH THE DRAWINGS THEN READ AND UNDERSTAND THE INSTRUCTIONS THOROUGHLY THIS PRODUCT MUST BE ASSEMBLED BY AN ADULT PRIOR TO USE DO NOT DESTROY THE PACKING AND CARTON UNTIL THE UNIT IS COMPLETELY ASSEMBLED DO NOT DESTROY THE INSTRUCTION MANUAL USE IT FOR ORDERING REPLACEMENT PARTS TO HELP SECURE PLASTIC CAPS IN TUBING IT IS ADVISABLE TO GLUE ALL PLA
4. STIC CAPS DURING ASSEMBLY USING ANY HOUSEHOLD TYPE GLUE PERIODICALLY CHECK THE UNIT FOR BOLT TIGHTNESS AND PARTS WEAR TO INSURE THAT YOUR EQUIPMENT 15 KEPT IN TOP CONDITION 139 2 SILVER MEDALLION PARTS LIST DIAGRAM NAME ORDERING 1242 08 25 6128 08 25 3178 08 25 0199 08 25 6054 06 25 0446 01 25 6112 23 25 KT1312 D13 F25 0394 01 25 6367 08 25 3179 08 25 0147 19 25 0437 25 25 KT6213 C19 F 25 KT6214 C19 F 25 6228 19 25 6215 19 25 KT6207 C19 F 25 KT6913 E06 F 25 HH 5199 F 25 L BRACKET FRONT SUPPORT BACKREST ADJ BAR SMALL FOAM PAD 2 X 6 PAD BAR 3 4 X 11 1 2 BACKREST LONG ANGLE IRON LARGE FOAM PAD 23 4 5 RIGHT BUTTERFLY BUTTERFLY WEIGHT PIN 1 11 BUTTERFLY PAD BAR 3 4 X 9 PAD BAR 3 4 13 1 2 ANGLE BRACKET 5 16 X 2 1 4 HEX HEAD BOLT 5 16 X 2 1 2 HEX HEAD BOLT 5 16 X 2 HEX HEAD BOLT 5 16 X 5 HEX HEAD BOLT 5 16 NYLON LOCK NUT 3 8 X 2 1 2 HEX HEAD BOLT 3 8 NYLON LOCK NUT 1 4 X 2 MACHINE SCREW 1 4 X 3 4 MACHINE SCREW 1 4 NYLON LOCK NUT 2 SQUARE PLASTIC INSERT CAP 1 1 2 SQUARE PLASTIC INSERT CAP 1 ROUND PLASTIC INSERT 1 ROUND PLASTIC COVER CAP WITH 15 DEGREE END 3 4 ROUND PLASTIC INSERT CAP a 8002 25 8001 25 8005 25 AA
5. USTOMER SERVICE 1 800 225 0653 ALL OF THE PARTS FOR THE WEIGHT BENCH CAN BE ORDERED FROM WEIDER HEALTH AND FITNESS PARTS SERVICE DEPT 900 WEST ST JOHN ST OLNEY IL 62450 WHEN ORDERING PARTS WILL BE SENT AND BILLED AT THE CURRENT PRICES PRICES MAY BE SUBJECT TO CHANGE WITHOUT NOTICE STANDARD HARDWARE ITEMS ARE AVAILABLE AT LOCAL HARDWARE STORES TO OBTAIN PARTS DO NOT GO BACK TO THE STORE WHERE YOU PURCHASED THIS UNIT ALWAYS INCLUDE THE FOLLOWING INFORMATION WHEN ORDERING PARTS MODEL NO NAME OF PART ORDERING NO WARNING CONSULT YOUR PHYSICIAN CONSULT YOUR PHYSICIAN BEFORE STARTING YOUR EXERCISE PROGRAM 15 ADVISABLE TO HAVE A PHYSICAL EXAMINATION BY YOUR PHYSICIAN BEFORE YOU ENTER ANY EXERCISE PROGRAM FOR YOUR OWN SAFETY DO NOT BEGIN ANY EXERCISE WITHOUT PROPER INSTRUCTION TRAIN WITH A PARTNER IT IS RECOMMENDED THAT AN INDIVIDUAL SHOULD NOT WORK OUT WITHOUT A TRAINING PARTNER IN ATTENDANCE SET UP YOUR PROGRAM TO ACCOMMODATE TWO PEOPLE AND YOU WILL BE HIGHLY MOTIVATED BEFORE BEGINNING ASSEMBLY READ THE FOLLOWING BY READING AND FOLLOWING THE ASSEMBLY INSTRUCTIONS YOU WILL FIND THAT THIS UNIT GOES TOGETHER EASILY THIS UNIT TAKES APPROXIMATELY ONE HOUR OF ASSEMBLY TIME TOOLS REQUIRED FOR ASSEMBLY INCLUDE A HAMMER PLIERS MEDIUM SIZE FLAT HEAD SCREWDRIVER AND 6 ADJUSTABLE WRENCHES PRIOR TO BEGINNING THE ASSEMBLY OF THIS PRODUCT WE RECOMMEND THAT YOU TAKE A FEW MINUTES TO UNPACK AN
6. X 2 1 4 HEX HEAD BOLTS 50 and 5 16 NYLON LOCK NUTS 55 Press 1 1 2 SQUARE PLASTIC CAP 71 into top of vertical member of MAIN FRAME 3 Into each end of the long PAD BAR 3 4 X 13 1 2 18 press 3 4 ROUND PLASTIC CAP 74 Apply a small amount of liquid dish detergent to the ends of the Pad Bar to act as a lubricant and slide on one FOAM PAD 2 X 6 6 Assemble the Pad Bar into the large hole in the top of the vertical member of the Main Frame Apply a small amount of liquid dish detergent to the opposite end and slide on the other FOAM PAD 2 X 6 6 Press 3 4 ROUND PLASTIC 74 into the handle end of BACKREST ADJ BAR 5 and position Bar into one of the hole patterns in UPRIGHT 1 The Backrest Adj Bar is used to position the Backrest into three Positions for doing various exercises UPRIGHT DECAL Remove the backing from DECAL 90 and align on UPRIGHT 1 below the bar holder bracket STEP 2 BACKREST AND SEAT ASSEMBLY the BACKREST 8 over to expose the threaded holes Position the LONG ANGLE IRONS 10 so that the flat side faces the outside of the Pad and fasten with 1 4 X 3 4 MACHINE SCREWS 59 DO NOT COMPLETELY TIGHTEN THESE SCREWS AT THIS TIME The bottom end of the BACKREST 8 is the end that the LONG ANGLE IRONS 10 extend past This is the end that is assembled to the MAIN FRAME 3 Straddle the Long Angle Irons over the hole in the Main Frame where the Backrest
7. reful not to over tighten or the Leg Curl will bind There are two Pad Bars to assemble next These Pad Bars 3 4 in diameter and are 11 1 2 long Press 3 4 ROUND PLASTIC CAPS 74 into both ends of each PAD BAR 7 Apply a small amount of liquid dish detergent to each Pad Bar and slide on one FOAM PAD 2 3 4 X 5 13 to each Pad Bar Assemble each Pad Bar into the large holes at the ends of LEG CURL 11 and slide on another FOAM PAD 2 2 3 5 13 STEP 4 BUTTERFLY ASSEMBLY There are two Butterfly Attachments with this unit a RIGHT BUTTERFLY 14 and a LEFT BUTTERFLY 15 Instructions are given for one and are repeated to assemble the other Assemble BUTTERFLY PAD BAR 17 through the large hole in the end of Butterfly Frame aligning bolt holes Secure with 1 4 X 2 MACHINE SCREW 58 and 1 4 NYLON LOCK NUT 60 Press 3 4 ROUND PLASTIC CAP 74 into end of BUTTERFLY PAD BAR 17 Slide LARGE FOAM PAD 2 3 4 X 5 13 onto end of BUTTERFLY PAD BAR 17 Again a small amount of liquid dish detergent will help with this assembly Assemble BUTTERFLY WEIGHT PIN 16 into angled hole on 58 front of Butterfly Frame and attach with 5 16 X 5 HEX HEAD BOLT 54 and 5 16 NYLON LOCK NUT 55 bolt will go through the Frame Weight Pin PLASTIC 76 SLEEVE 77 will then be assembled onto the bolt and Secured with the 5 16 NYLON LOCK NUT 55 Press 1 8 ROUND PLASTIC CAP 72 in
8. sw MEDALLION WAIT READ THIS FIRST If you find this unit to have missing or defective parts please have ready the following information listed below before calling the 800 NUMBER The ASSEMBLY MANUAL MODEL NUMBER of this UNIT PART NAME or DESCRIPTION ORDERING NUMBER THE QUANTITY of each part that you need THE MODEL NUMBER of this unit is found in the UPPER LEFT HAND or RIGHT HAND CORNER of this page The MODEL NUMBER is a series of 3 or 4 NUMBERS THE PART NAME or DESCRIPTION and the ORDERING NUMBER can be found on the PARTS LIST PAGE weider OWNER S MANUAL rt ey ee MADE IN TAIWAN WEIDER is committed to providing you complete customer satisfaction If you have any questions concerning the assembly of this product or find damaged or missing parts we guarantee you direct assistance AVOID THE HASSLE OF CONTACTING THE STORE FOR PARTS OR RETURNING THE PRODUCT Call our CUSTOMER ASSISTANCE LINE for assistance with parts and information by calling our toll free number 1 800 225 0653 Mon Fri 8 am 5 pm CST IMPORTANT Read all safety precautions and instructions in this manual carefully before using this equipment Save this manual for future reference WEIDER HEALTH AND FITNESS 21100 Erwin Street Woodland Hills Ca 91367 USA REPAIR PARTS AND SERVICE BEFORE CALLING THE 800 NUMBER IN ORDER TO RECEIVE SERVICE ON THIS PRODUCT YOU WILL HAVE TO FIRST SEND IN YOUR WARRANTY CARD C
9. to end of Weight Pin Slide PLASTIC BUSHING 75 over Weight Pin until it is against the Butterfly Frame 71 72 Assemble PLASTIC SLEEVE 76 over welded Butterfly Tube Slide entire assembly into welded tube bracket on UPRIGHT 1 1 Insert STOPPER PIN 78 into center of assembly rounded end first making sure the side of the Stopper Pin that has a raised section is aligned with the hole in the welded Butterfly Tube Push STOPPER PIN 78 into welded Butterfly Tube until it clicks into place as the raised section exits the hole Press a 1 1 2 SQUARE PLASTIC CAP 71 into end of Frame
Download Pdf Manuals
Related Search