Weider C135 User's Manual
Contents
1. C135 ASSEMBLY INSTRUCTIONS REPLACEMENT PARTS WEIDER HEALTH AND FITNESS 21100 ERWIN ST WOODLAND HILLS CA U S A 91367 TABLE OF CONTENTS ee ACE REPAIR PARTS AND SERVICE l 131 eer 2 12 STEP 1_ FRAME ASSEMBLY a TEP 2 BACKREST PREPARATION 5 ee 4 4 e 15227 O fa eae es STEP 3 ATTACHING BACKREST AND SEAT STEP 4 ATTACHING LEG CURL STEP 5 ARM CURL ASSEMBLY ALL OF THE PARTS FOR THE WEIGHTBENCH CAN BE ORDERED FROM WEIDER HEALTH AND FITNESS PARTS SERVICE DEPT 900 WEST ST JOHN ST OLNEY ILL 62450 WHEN ORDERING PARTS WILL BE SENT AND BILLED AT THE CURRENT PRICES PRICES MAY BE SUBJECT TO CHANGE WITHOUT NOTICE STANDARD HARDWARE ITEMS ARE AVAILABLE AT LOCAL HARDWARE STORES TO OBTAIN PARTS DO NOT GO BACK TO THE STORE WHERE YOU PURCHASED THIS UNIT IF YOU FIND THIS PRODUCT TO HAVE EITHER A DEFECTIVE PART OR A MISSING PART WRITE THE ABOVE ADDRESS OR PHONE CUSTOMER SERVICE AT 1 800 225 0653 ALWAYS INCLUDE THE FOLLOWING INFORMATION WHEN ORDERING PARTS MODEL NO NAME OF PART ORDERING NUMBER C 135 4 3 89 PARTS LIST C 135 DIAGRAM ORDERING NO PART NAME NUMBER ____1__ UPRIGHT O 1 CC10 0242 2 2 MAIN FRAME f CC10 0201 __ 4 1771 4 09 0113 26 BACKREST 1 10 0360 61 SET LT 1 0 0370 r M 7 _ O O o o 2 09 605 8 1 24 CAO1 0400 l 9 BACK2. STEP 1 FRAME ASSEMBLY Begin by inserting 2 SQUARE PLASTIC CAPS D into UPRIGHT 1 Align bolt holes in L BRACKET 11 with holes in UPRIGHT 1 and secure each bracket with 2 HEX HEAD BOLTS M and 2 LOCK NUTS J Insert ROUND PLASTIC CAP B into each end of WEIGHT STACK PINS 12 insert pins into UPRIGHTS 1 and secure with HEX HEAD BOLT H and LOCK NUT J Align holes in main frame front u bracket and FRONT SUPPORT 3 Secure with 2 HEX HEAD BOLTS H and LOCK NUTS J Secure rear u bracket on MAIN FRAME 2 to crossbar of UPRIGHTS 1 using 2 HEX HEAD BOLTS H and LOCK NUTS J Insert 2 SQUARE PLASTIC CAPS E into FRONT SUPPORT 3 Tighten all bolts NOTE The lower or attachment end of the BACKREST 5 can be identified quickly by the LONG ANGLE IRONS 10 The LONG ANGLE IRONS 10 will be ex tended approximately two inches 2 beyond the BACKREST PAD 5 STEP 2 BACKREST PREPARATION Turn BACKREST 5 over to expose work area Both LONG ANGLE IRONS 10 have been fastened to BACKREST 5 for shipment One long angle iron must be loosened in order to assemble BACKREST 5 to main frame pivot The lower MACHINE SCREW K must be removed while the upper MACHINE SCREW K is only loosened The LONG ANGLE IRON 10 can now Swing freely from the lower end of BACKREST 5 DETAIL A STEP 3 ATTACHING BACKREST amp SEAT BACKREST To aid in attaching Backrest first slide the BACKREST ADJ B
3. AR 9 through one of the hole patterns in the uprights With LONG ANGLE IRON 10 free lower BACKREST 5 to main frame Pivot rod Slide the secured LONG ANGLE IRON 10 onto one side of pivot rod Swing the free LONG ANGLE IRON 10 back to its original position and onto the opposite end of the pivot rod See Detail A Replace MACHINE SCREW K that was removed in Step 2 and tighten all machine screws SEAT With SEAT 6 right side up lower SEAT 6 to seat brackets on main frame Align bolt holes and fasten with 2 MACHINE SCREWS K Tighten all machine screws STEP 4 ATTACHING LEG CURL Place LEG CURL 4 between leg curl brackets on main frame and align bolt holes Secure with HEX HEAD BOLT F and LOCK NUT 6 Repeat the following in Structions until all PAD BARS 7 and FOAM PADS 8 are in place First slide PAD BAR 7 through proper hole in LEG CURL 4 until equal amounts of bar are on both sides of LEG CURL 4 Slide one FOAM PAD 8 onto PLASTIC CAP 1 BAR 7 Insert SQUARE nto end of LEG CURL 4 Use LOCKING PIN L to lock leg curl to main doing specific exercises Leg Curi Brackets 4 STEP 5 ARM CURL Assemble arm curl by aligning holes in BRACKET 14 with holes in ARM CURL BAR 15 Secure with 2 HEX HEAD BOLTS N and LOCK NUTS J Attach completed assembly to arm curl pad using 3 ROUND HEAD SCREWS K Insert SQUARE PLASTIC CAP 0 into each end of BAR 15 To use ar
4. REST ADJ BAR 4 CA06 6054 10 LONG ANGLE IRON 2 CA09 6047 COT SCL BRACKET 2 CC10 6140 po WEIGHT STACK 2 07 6134 7777152 ARM CURL BAR C f f CC10 6142 See ea U eee Y i Z Y Si Ee papapas psta apus LS nee rn x _____ _ 09 5800 PCE _1 1 2 50 PLASTIC 3 AA M 8001 x 3 8 16 2 1 2 HEX HEAD BOLT 1 HH 5018 J 3 8 16 LOCK NUT t HH 5013 x H _5 16 20 2 174 HEAD BOLT 6 HH 5035 ___ 57167 20 LOCK NUT 12 1 5024 K 1 4 20 3 4 MACHINE SCREW x 9 _ HH 5022 11 LOCKING PIN i WW 7004 57 16 20 2 1 2 HEX HEAD BOLT 4 5015 fh BT BISEX HEAD BOLT 2 f 5240 Ooo SQ ST AP _ CALS Dd D 477 j INSTRUCTION MANUAL __1__ NN 1060 WARNING CONSULT YOUR PHYSICIAN CONSULT YOUR PHYSICIAN BEFORE STARTING YOUR EXERCISE PROGRAM IS AOVISABLE TO HAVE A PHYSICAL EXAMINATION BY YOUR PHYSICIAN BEFORE YOU ENTER ANY EXERCISE PROGRAM FOR YOUR OWN SAFETY NOT BEGIN ANY EXERCISE WITHOUT PROPER INSTRUCTION CHILDREN AND HANDICAPPED PERSONS SHOULD NOT USE ANY EXERCISE EQUIPMENT WITHOUT A QUALIFIED PERSON IN ATTENDANCE TRAIN WITH A PARTNER IT IS RECOMMENDED THAT AN INDIVIDUAL SHOULD NOT WORKOUT WITHOUT A TRAINING PARTNER IN ATTENDANCE SET UP YOUR PROGRAM TO ACCOMMODATE TWO PEOPLE AND YOU WILL BE HIGHLY MOTIVATED
5. m curl mount it to upright by inserting long ear of bar holder into slots in arm curl bar BOLT LENGTH SCALE
Download Pdf Manuals
Related Search