Weider E127 User's Manual
Contents
1. 1 4 X 1 1 2 MACHINE SCREW 5 16 FLAT WASHER2. E127 WEIGHT BENCH OWNERS MANUAL MODEL NO 354 15525 WEIDER HEALTH AND FITNESS 21100 ERWIN STREET WOODLAND HILLS CA USA 91367 BEGINNING ASSEMBLY READ THE FOLLOWING BY READING AND FOLLOWING THE ASSEMBLY INSTRUCTIONS YOU WILL FIND THAT THIS UNIT GOES TOGETHER EASILY THIS UNIT TAKES APPROXIMATELY ONE HOUR OF ASSEMBLY TIME _ TOOLS REQUIRED FOR ASSEMBLY INCLUDE A HAMMER PLIERS MEDIUM SIZE FLAT HEAD SCREWDRIVER AND TWO 6 ADJUSTABLE WRENCHES _ PRIOR TO BEGINNING THE ASSEMBLY OF THIS PRODUCT WE RECOMMEND THAT YOU TAKE A FEW MINUTES TO UNPACK AND LAY OUT ALL THE PARTS SO THEY CAN BE EASILY IDENTIFIED IT IS EXTREMELY HELPFUL IF THE CONTENTS OF THE HARDWARE BAG ARE EMPTIED OUT AND LIKE PARTS GROUPED TOGETHER I E 5 16 X 3 HEX HEAD BOLTS TOGETHER ETC A HANDY PLACE TO HOLD THE HAROWARE MIGHT BE TO USE THE INSIDE OF THE CARTON TOP AFTER GROUPING PARTS AGAINST THE PARTS LIST TO IDENTIFY PARTS AND SIZES WRITE THE SIZE AND PART NAME BESIDE EACH PART SO YOU KNOW EXACTLY WHICH PART TO GO TO FOR A PARTICULAR ITEM THE ASSEMBLY INSTRUCTIONS HAVE BEEN WRITTEN USING CHECK AS YOU GO ASSEMBLY METHOD BY CHECKING THE BOXES AS YOU GO IT IS VERY EASY TO FOLLOW ALONG THE ASSEMBLY WITHOUT REREADING TO FIND YOUR PLACE IN THE ASSEMBLY YOU WILL ALSO NOTICE THAT AT THE BEGINNING OF EACH ASSEMBLY STEP THERE IS HARDWARE LIST SHOWING THE QUANTITY AND DESCRIPTION OF THE HARDWARE REQUIRED TO DO ALL ASSEMBLIES IN THAT STEP BY
3. LTS Position LONG ANGLE IRONS 7 with flat side to the outside onto BACKREST 6 Secure one LONG ANGLE IRON 7 with 1 4 X 3 4 MACHINE SCREWS 38 and the other at the top only with one 1 4 X 3 4 MACHINE SCREW 38 DO NOT TIGHTEN COMPLETELY 6 0 side BACKREST ADJ BAR 11 through one of the hole patterns in UPRIGHT 1 Position secured LONG ANGLE IRON 7 onto pivot rod and slide the freed end of opposite angle iron back into position and onto opposite end of rod Attach angle iron with 1 4 X 3 4 MACHINE SCREW 38 and tighten all machine screws C with SEAT 8 right side up lower to Seat Bracket on MAIN FRAME 3 and attach with 1 4 X 3 4 MACHINE SCREWS 38 and 5 16 FLAT WASHERS 42 LOOSE 7 38 TOR 2 TURNS Slide WEIGHT PIN 12 through angled hole on front of LEG CURL 5 Align bolt holes and attach with 5 16 X 1 3 4 HEX HEAD BOLT 36 and 5 16 NYLON LOCK NUT 37 Assemble 1 ROUND PLASTIC COVER CAP 15 32 over rear extended portion of Weight Pin Assemble 1 ROUND PLASTIC CAP 31 into end of Weight Pin Assemble 1 1 4 SQUARE PLASTIC 33 into end of LEG CURL 5 Position LEG CURL 5 between Leg Curl Bracket MAIN FRAME 3 and secure with 3 8 X 2 1 4 HEX HEAD BOLT 34 and 3 8 NYLON LOCK NUT 35 DO NOT OVER TIGHTEN THIS BOLT J THE FOLLOWING INSTRUCTIONS ARE REPEATED UNTIL ALL REMAINING LEG CURL PARTS ARE IN PLACE Assemble 3 4 ROUND PLASTIC CAPS 30 into e
4. PRE SELECTING THE HARDWARE FOR EACH STOP YOU WILL SAVE TIME AND CONFUSION TAKE NOTE OF ANY SPECIAL WARNINGS CAUTIONS NOTES OR NOTICES LAY OUT UNASSEMBLED PARTS FAMILIARIZE YOURSELF WITH THE DRAWINGS THEN READ AND UNDERSTAND THE INSTRUCTIONS THOROUGHLY THIS PRODUCT MUST BE ASSEMBLED BY AN ADULT PRIOR TO USE DO NOT DESTROY THE PACKING AND CARTON UNTIL THE UNIT IS COMPLETELY ASSEMBLED DO NOT DESTROY THE INSTRUCTION MANUAL USE IT FOR ORDERING REPLACEMENT PARTS TO HELP SECURE PLASTIC CAPS IN TUBING IT IS ADVISABLE TO GLUE ON ALL PLASTIC CAPS DURING ASSEMBLY USING ANY HOUSEHOLD TYPE GLUE PERIODICALLY CHECK THE UNIT FOR BOLT TIGHTNESS AND PARTS WEAR TO INSURE THAT YOUR EQUIPMENT IS KEPT IN TOP CONDITION DEG C Begin by inserting 1 1 2 SQUARE PLASTIC CAPS 43 into UPRIGHT 1 Bj Align bolt holes on L BRACKETS 2 with bolt holes on UPRIGHT 1 Secure each bracket with 5 16 X 2 HEX HEAD BOLTS 39 and 5 16 NYLON LOCK NUTS 37 Align MAIN FRAME 3 bracket with holes FRONT SUPPORT 4 and secure with 1 4 X 1 1 2 MACHINE SCREW 41 and 1 4 NYLON LOCK NUT 44 NOTE The recessed holes on FRONT SUPPORT 4 will be placed toward the floor Lower rear u bracket of MAIN FRAME 3 onto cross member of UPRIGHT 1 Align bolt holes and secure with 5 16 X 2 1 4 HEX HEAD BOLTS 45 and 5 16 NYLON LOCK NUTS 37 1 insert 1 1 4 SQUARE PLASTIC CAPS 33 into FRONT SUPPORT 4 TIGHTEN ALL BO
5. nd of PAD 37 BAR 11 1 2 9 Slide PAD BAR 11 1 2 9 through proper hole LEG CURL 5 until equal amounts of both sides the following assembly small amount 36 liquid dish detergent should be applied to both ends of the Pad Bar 12 0 Assemble LARGE FOAM PADS 2 3 4 X 5 10 onto each 5 end BAR 11 1 2 9 PART LIST E127 DIAGRAM NO PART NAME ORDERING NO uemer E emses omos WANFRAME ard Baar 1 Cisso E0t LONGANGLEIRON 2 cees EE PAD BAR 3 4 X 11 1 2 2 Ce112 A23 FOAM PAD 2 3 4 X S BACKRESTADJBAR 6045 A05 weeen 1 c0m47018 54 AA 80084 Sa HE eet ME are ME pe ss FE ee EE O Fr _ FER FL ME fr ME O an 1 ROUND PLASTIC rae 32 ROUND PLASTIC COVER o ____ 3 1 4 SQUARE PLASTIC CAP 138 X21 4 HEX HEAD BOLT 1 HH 5061 35 NYLON LOCK NUT 1 3 15 16 1 34 HEX HEAD BOLT Q 5 16 NYLON LOCK HH 5012 38 14 X 3 4 MACHINE SCREW HH5022 so Jfsn6 xarmexHeaDBOT Hh 054 x fwarx194 MACHINESCREW _ ____ 2 HE DN 2 HH5250 ____ 42 O 2 _ Hr 5127 ME 4 O o 52 wasan est 5 C Per FEE ME ee
Download Pdf Manuals
Related Search