Weider C132 User's Manual
Contents
1. STEP 5 BUTTERFLY ATTACHMENT There are two butterfly attachments with this unit a RIGHT BUTTERFLY 12 and a LEFT BUT TERFLY 16 Instructions for assembly are given for one and are repeated to assemble Detail B the other First observe the end of BUTTERFLY PAD BAR 13 that has l of the threaded insert Slide the J threaded end through the Le E D large hole in the BUT TERFLY 12 until the Q BUTTERFLY PAD BAR 13 is against the opposite side and aligned with the small hole Thread HEX HEAD BOLT G through small hole into thread ed insert in BUTTERFLY PAD BAR 13 and 0 tighten Insert ROUND PLASTIC CAP H into BUTTERFLY PAD BAR 13 Slide BUTTERFLY FOAM PAD 14 over BUTTERFLY PAD BAR 13 Insert ROUND PLASTIC CAP into welded tube on BUTTERFLY 12 Insert ROUND PLASTIC into weight pin on BUTTERFLY 12 Assemble PECK DECK PIN S into lower hole in UPRIGHT 1 This pin is used as a stop for the butterfly attachment Slide PLASTIC SLEEVE U over welded tube Slide entire assembly into welded tube bracket on UPRIGHT 1 making sure to align holes on top of both tubes Insert STOPPER PIN T into center of assembly rounded end first making sure the side of the STOPPER PIN T that has a raised section is on top and aligned with holes in assembly Push STOPPER PIN T in until it clicks into place as raised section exits the hole ee Detail B STEP 6 COMPLET2. NN 1065 ASSEMBLY INSTRUCTIONS REPLACEMENT PARTS WEIDER HEALTH AND FITNESS 21100 ERWIN ST WOODLAND HILLS CA U S A 9136 d TABLE OF CONTENTS PSR le ee TE HASSE ON FRERE FT GAS FEN 2 REPAIR PARTS and SERVICE FRE EP HSE FEE FAE NEDSETTER STEP 2 BACKREST PREPARATION NST ENER step 3 ATTACHING BACKREST and SEAT 4 STEP 4 ATTACHING LEG CURL ean KE step 5 BUTTERFLY ATTACHMENT 5 STEP 6 COMPLETED BENCH Pre Saree C 132 PARTS LIST DIAGRAM PART NAME ORDERING NO cn NO UPRIGHT aes ni 2 MAIN FRAME _ 3 FRONT SUPPORT 14 LEG CURL BACKREST anny 1 1 1 JER 0 2 CA25 6118 8 L BRACKET 2 CA22 6125 9 PAD BAR 2 cc08 6136 FOAM PAD 4 cA05 0425 BACKREST ADJ BAR RIGHT BUTTERFLY 13 BUTTERFLY PAD BAR 2 CC14 6157 14 BUTTERFLY FOAM PAD 1 2 CB18 0412 15 ADJUSTABLE UPRIGHT 2 CA22 0230 CC14 6158 NGC EDS GN AMNEM NIE a Ecco __ HARDWARE BAG 14 CC14 5805 A 5 16 20X 2 1 272 HH 5015 5 16 20 x 2 4 HH 5017 c 5 16 20 LOCK NUT 8 8HH 5021 TD 1 4 20 X 3 4 MACHINE SCREW 6 HH 5022 E 3 8 16 X 2 1 2 HEX HEAD BOLT vr 3 8 16 LOCK NUT 1 HH 5013 9 G 3 8 16 X 1 HEX HEAD BOLT 2 HH 5262 X 3 4 ROUND PLA
3. BAR 11 through one of the hole patterns in the UPRIGHT 1 With LONG ANGLE IRON 7 free lower BACKREST 5 to Main FRAME Pivot Rod Slide the secured LONG ANGLE IRON 7 onto one side of Pivot Rod Swing the free LONG ANGLE IRON 7 back to its original position and onto the opposite end of the Main Frame Pivot Rod See Detail A Re place MACHINE SCREW D that was removed in Step 2 and tighten all machine screws SEAT With SEAT 6 right side up lower to seat brackets on MAIN FRAME 2 Align bolt holes and fasten with 2 MACHINE SCREWS D Leg Curl Brackets STEP 4 ATTACHING LEG CURL Place LEG CURL 4 between Leg Curl Brackets on Main Frame and align bolt holes Secure with HEX HEAD BOLTS E and LOCK NUT F DO NOT OVERTIGHTEN LEG CURL 4 must be abfe to swing free Repeat the following instructions until all PAD BARS 9 and FOAM PADS 10 are in place First slide PAD BAR 9 through proper hole in LEG CURL 4 until equal amounts of bar are on both sides of LEG CURL 4 Slide on FOAM PAD 10 onto each PAD BAR 9 A small amount of dishwashing liquid ap plied to each end of the PAD BAR 9 will aid in this assembly Insert ROUND PLASTIC CAP H into each end of PAD BAR 9 Insert SQUARE PLASTIC CAP N into end of LEG CURL 4 ROUND PLASTIC CAP J is placed into the outside end of the weight pin on LEG CURL W hile the ROUND PLASTIC CAP K is placed over the rear extended piece of the weight pin
4. ED BENCH Slide ADJUSTABLE UPRIGHTS 15 into UPRIGHT 1 Use LOCKING PINS Q to ad just the height of the ADJUSTABLE UPRIGHTS 15 The BACKREST ADJ BAR 11 is used to adjust the height of the BACKREST 5 It can also be used to adjust the height of the ADJUSTABLE UPRIGHTS 15 but is not used in conjunction with LOCKING PINS Q LOCKING PIN R is used to Tock the LEG CURL 4 to the MAIN FRAME gt WARNING CONSULT YOUR PHYSICIAN CONSULT YOUR PHYSICIAN BEFORE STARTING YOUR EXERCISE PROGRAM IT IS ADVISABLE TO HAVE A PHYSICAL EXAMINATION BY YOUR PHYSICIAN BEFORE YOU ENTER ANY EXERCISE PROGRAM FOR YOUR OWN SAFETY DO NOT BEGIN ANY EXERCISE WITHOUT PROPER INSTRUCTION CHILDREN AND HANDICAPPED PERSONS SHOULD NOT USE ANY EXERCISE EQUIPMENT WITHOUT A QUALIFIED PERSON IN ATTENDANCE TRAIN WITH A PARTNER IT IS RECOMMENDED THAT AN INDIVIDUAL SHOULD NOT WORKOUT WITHOUT A TRAINING PARTNER IN ATTENDANCE SET UP YOUR PROGRAM TO ACCOMMODATE TWO PEOPLE AND YOU WILL BE HIGHLY MOTIVATED
5. STIC CAP 6 AA 8004 1 ROUND PLASTIC CAP 3 AA 800 K Liv COVER car 1 _AA 8070 O M 2 SQUARE PLASTIC CAP 2 AA 8002 rN 1 1 2 SQUARE PLASTIC CAP 5 AA 8000 TB 7 8 ROUND PLASTIC CAP 2 A 8088 9 SMALL LOCKING PIN 2 wwW 7002 R LARGE LOCKING PIN s PECK DECK 2 wW7037xX 47 STOPER 2 FU PLASTIC SLEEVE 2 UPRIGHT DECAL E DE 4070 7 INSTRUCTION MANUAL 1 1 1 ALL OF THE PARTS FOR THE WEIGHTBENCH CAN BE ORDERED FROM WEIDER HEALTH AND FITNESS PARTS SERVICE DEPT 900 WEST ST JOHN ST OLNEY ILL 62450 WHEN ORDERING PARTS WILL BE SENT AND BILLED AT THE CURRENT PRICES PRICES MAY BE SUBJECT TO CHANGE WITHOUT NOTICE STANDARD HARDWARE ITEMS ARE AVAILABLE AT LOCAL HARDWARE STORES TO OBTAIN PARTS DO NOT GO BACK TO THE STORE WHERE YOU PURCHASED THIS UNIT IF YOU FIND THIS PRODUCT TO HAVE EITHER A DEFECTIVE PART OR A MISSING PART WRITE THE ABOVE ADDRESS OR PHONE CUSTOMER SERVICE AT 1 800 225 0653 ALWAYS INCLUDE THE FOLLOWING INFORMATION WHEN ORDERING PARTS MODEL NO C132 NAME OF PART ORDERING NUMBER 2 ASSEMBLY INSTRUCTIONS Before starting remove all pieces from the box and lay them out on a clean surface Check the parts list to verify that you have all the pieces The diagram on Page 1 will also be helpful i Tools needed Flat Head Sc
6. rewdriver Adjustable Wrench Pliers Hammer STEP 1 FRAME ASSEMBLY Begin by inserting 2 SQUARE PLASTIC CAPS M into UPRIGHT 1 Align bolt holes on L BRACKET 8 with bolt holes on UPRIGHT 1 Secure each L BRACKET 8 with 2 HEX HEAD BOLTS A and 2 LOCK NUTS C Align bolt holes on MAIN FRAME 2 front u bracket and FRONT SUPPORT 3 Secure with 2 HEX HEAD BOLTS B and 2 LOCK NUTS C Lower rear u bracket of MAIN FRAME 2 onto crossmember of UPRIGHT 1 aligning bolt holes Secure with 2 HEX HEAD BOLTS B and 2 LOCK NUTS C Insert 2 SQUARE PLASTIC CAPS N into FRONT SUPPORT 3 Tighten all bolts LOOSEN 10R 2 TURNS STEP 2 BACKREST PREPARATION Note The lower or attachment end of the BACKREST 5 can be identified quickly by the LONG ANGLE IRONS 7 The LONG ANGLE IRONS 7 will be ex tended approximately two inches be yond the BACKREST 5 Turn BACKREST 5 over to expose work area Both LONG ANGLE IRONS 7 have been fastened to BACKREST 5 for shipment One LONG ANGLE IRON 7 must be loosened in order to assemble BACKREST 5 to Main Frame Pivot Rod The lower MACHINE SCREM D must be removed while the upper 3 MACHINE SCREW D is only loosened The LONG ANGLE IRON 7 can now swing free from the lower end of BACKREST 5 DETAIL A STEP 3 ATTACHING BACKREST amp SEAT BACKREST To aid in attaching BACKREST 5 first slide BACKREST ADJ
Download Pdf Manuals
Related Search