Weider 1033 ULTRAMAX BENCH 1033 User's Manual
Contents
1. MODEL NO 1033 SERIAL NO Write serial number in the space above for reference SERIAL NUMBER DECAL WAIT READ THIS FIRST If you find this unit to have missing or defective parts please have ready the following Information listed below before calling the 800 NUMBER The ASSEMBLY MANUAL MODEL NUMBER of this UNIT PART NAME or DESCRIPTION ORDERING NUMBER THE QUANTITY of each part that you need THE MODEL NUMBER of this unit can be found in the UPPER LEFT HAND or RIGHT HAND CORNER of this page The MODEL NUMBER Is a series of FOUR or FIVE NUMBERS or a NUMBER preceeded by TWO LETTERS THE PART NAME or DESCRIPTION and the ORDERING NUMBER can be found on the PARTS weider OWNER S MANUAL o a MADE IN CANADA l WEIDER is committed to providing you complete customer satisfaction If you have any questions concerning the assembly of this product or find damaged or missing parts we guarantee you direct assistance AVOID THE HASSLE OF CONTACTING THE STORE FOR PARTS Call our CUSTOMER ASSISTANCE LINE for assistance with parts and information by calling our toll free number 1 800 225 0653 Mon Frl 8am Spm CST IMPORTANT Read all safety precautions and instructons in this manual carefully before using this equipment Save this manual for future reference Printed in CANADA WEIDER SPORTING GOODS INC 21100 Erwin Street Woodland Hills CA 91367 USA PAGE 1 WEIDER SPORT2. G01 HH 5244 G01 WW 7038 G01 AA 8002 G01 AA 8070 G01 AA 8004 G01 AA 8005 G01 AA 8093 G01 8088 601 AA 8001 G01 WW 7002 G01 3 8 NYLON LOCK NUT 3 8 X 2 1 2 HEX HEAD BOLT 3 8 X 1 1 2 HEX HEAD BOLT 3 8 X 2 HEX HEAD BOLT STOPPER PIN 67 1 2 X 3 4 LONG METAL SPACER NEXU 68 2 1 3 8 LONG METAL SPACER o 30 8128 G01 1 2 O D X 3 LONG PLASTIC SPACER S HOOK 7030 G01 WEIGHT STOP AA 8112 GO1 PLASTICSLEEVE 1 1 8 O D X 2 LONG 2 AAs0901 G01 jit UPRIGHT DECAL DE 4373 G01 ASSEMBLY MANUAL CNN 1255 G01 70 71 72 HARDWARE BAG BOLTS amp NUTS 1 care9 cot G0 HARDWARE BAG PLASTICS C8790 G01 G01 MAINTENANCE TIPS Keeping your weight bench in good condition will help insure you many hours of safe enjoyable exercise Following an easy maintenance routine will prevent premature wear and unnecessary parts replacement 1 Check all fasteners nuts and bolts and caps to see that they are tight and fitted properly 2 Lubricate all moving parts frequently to keep handles and other parts moving smoothly and eliminate squeaks and excessive noise l 3 Painted surfaces can be cleaned with a soft cloth and a mild non abrasive detergent PAGE 4 WEIDER SPORTING GOODS ORDERING PARTS Weider is dedicated to insure that each product is ma
3. PIN 7 or the WEIGHT BAR 10 PAGE 11 WEIDER SPORTING GOODS STEP 7 37 5 16 X 5 HEX HEAD BOLT 40 1 4 NYLON LOCK NUT 142 1 4 X2 ROUND HEAD MACHINE SCREW 51 STOPPER PIN 11 2 SQUARE PLASTIC INSERT CAP 58 sa RouNDPLAsTICINSERTCAP Ta 3 1 8 0 0 X 2 LONG PLASTIC SLEEVE BUTTERFLY ASSEMBLY There are two Butterfly attachments with this unit RIGHT BUTTERFLY 20 and a LEFT BUTTERFLY 21 Instructions are given for one and are repeated to assemble the other O Assemble the end with the hole of the 3 4 X 9 BUTTERFLY PAD BAR 22 into the large hole in the side and at the upper end of the Butterfly Frame Assemble this into the side of the Frame which does not have the welded round tube Aligning bolt holes and using a 1 4 X 2 MACHINE SCREW 42 bolt down through the top of the Butterfly Frame and then through the Butterfly Pad Bar Secure with a 1 4 NYLON LOCK NUT 40 Press a 3 4 ROUND PLASTIC INSERT CAP 58 into the end of the BUTTERFLY PAD BAR 22 Slide a 3 X 5 1 2 FOAM ROLLER PAD 11 onto the end of the Butterfly Pad Bar Again a small amount of liquid dish detergent will help with this assembly At the other end of the Butterfly Frame there is a large angled hole on the inside of the Frame Assemble the end of the BUTTERFLY WEIGHT PIN 1 X 10 1 2 23 with the hole into the large hole on the inside of the Frame Using a 5 16 X 5 HEX HEAD
4. to the store simply contact Weider Customer Assistance at 1 800 225 0653 Monday Friday 8 a m 5 p m CST All parts and service inquiries should be directed to Weider Sporting Goods Parts Service Department 900 West St John Street Olney Illinois 62450 PAGE 5 WEIDER SPORTING GOODS STEP 1 FRAME ASSEMBLY L Begin by pressing 2 SQUARE PLASTIC INSERT CAPS 55 into the bottom ends of the UPRIGHT 1 30 5 16 NYLON LOCK NUT 31 5 16 X2 1 2 HEAD BOLT 39 5 16 X2 1 4 HEX HEAD BOLT 55 2 SQUARE PLASTIC INSERT CAP 56 11 2 SQUARE PLASTIC INSERT CAP L Align the BASE FRAME 2 with the UPRIGHT 1 and secure using 5 16 X 2 1 2 HEX HEAD BOLTS 31 to bolt through the bracket of the Base Frame and into the front of the Upright Secure with 5 16 NYLON LOCK NUTS 30 C Assemble the MAIN FRAME 3 to the UPRIGHT 1 and BASE FRAME 2 by positioning the rear U bracket of the Main Frame over the cross member tube of the Upright and positioning the front U bracket over the Base Frame tube C Secure the rear U bracket at the UPRIGHT 1 using 5 16 X 2 1 4 HEX HEAD BOLTS 39 to bolt through the U bracket and then through the front of the Upright Secure with 5 16 NYLON LOCK NUTS 30 L Secure the front U bracket at the BASE FRAME 2 using a 5 16 X 2 1 4 HEX HEAD BOLT 39 and bolting through the U bracket and then through the Base Frame Secure with a 5 16 NYLON L
5. BOLT 37 bolt through the Butterfly Frame and then through the Weight Pin Assemble a 1 2 X 3 LONG PLASTIC SPACER 69 onto the Bolt end and secure with a 5 16 NYLON LOCK NUT 30 L Press a 1 ROUND PLASTIC INSERT CAP 59 into the end of the WEIGHT PIN 23 Slide a WEIGHT STOP 71 over the Weight Pin until it is against the Butterfly Frame C Assemble a 1 1 8 O D X 2 LONG a6 PLASTIC SLEEVE 72 over the Welded Round Tube on the Butterfly 51 Frame Slide the entire assembly now into the Welded Tube Bracket on the UPRIGHT 1 0 insert the STOPPER PIN 51 into end first making sure the side of the Stopper Pin that has a raised section is aligned with the hole in the Welded Butterfly Round Tube Push the Stopper Pin into the Welded Butterfly Tube until it clicks into place as the raised section exits the hole the center of the assembly rounded Press a 7 8 ROUND PLASTIC INSERT CAP 60 into the Welded Butterfly Round Tube C Press a 1 1 2 SQUARE PLASTIC INSERT CAP 56 into the top end of the Butterfly Frame WELDED TUBE BRACKET 72 WELDED BUTTERFLY ROUND TUBE
6. IDER SPORTING GOODS STEP 6 MAST ASSEMBLY 30 5 16 NYLON LOCK NUT rae 34 5 16 X 1 3 4 EYELET BOLT 5 16 X 2 CARRIAGE BOLT 36 5 16 ACORN NUT 145 3 8 NYLON LOCK NUT 47 38 X1 1 2 HEX HEAD BOLT 4 3 8 X 2 HEX HEAD BOLT 56 11 2 SQUARE PLASTIC INSERT CAP 6 59 A 1 ROUND PLASTIC COVER CAP 9 1 8 7 1 2 O D X 3 4 LONG METAL SPACER 68 1 2 O D X 1 3 8 LONG METAL SPACER Connect the MAST TOP SECTION 14 and the MAST BOTTOM SECTION 15 using MAST CONNECTOR PLATES 16 and securing with 5 16 X 2 CARRIAGE BOLTS 35 by bolting through the Plates and then through the Mast Sections Fasten with 5 16 ACORN NUTS 36 O insert a 1 2 X 3 4 LONG METAL SPACER 67 into the PULLEY 17 Drape the SHORT CABLE 13 over the Pulley and assemble the Pulley into the Pulley Plates at the bottom of the MAST BOTTOM SECTION 15 trapping the Cable behind the Pulley Secure in place using a 3 8 X 1 12 HEX HEAD BOLT 47 and bolting through the Plates and into the Pulley Secure with a 3 8 NYLON LOCK NUT 45 PAGE 10 WEIDER SPORTING GOODS insert a 1 2 X 1 3 8 LONG METAL SPACER 68 into a PULLEY 17 Insert the Pulley into the top of the TOP MAST SECTION 14 and using 3 8 X 2 HEX HEAD BOLT 48 bolt ir place by belting through the top of the Mast and then through the Pulley Secure
7. ING GOODS TABLE OF CONTENTS Table of Contents 1 Important Safety PrecautionS 1 Introduction den se eek ERE Ra n RR Fee 1 Assembly SIDS beet ee ewes 5 1 1 Maintenance Tips 3 Parts coss ER EG ee eae eee eS TX Kawa es 2 3 Ordering Parts os sc voces ewes rrr eee ees 4 Thank you for choosing Weider fitness equipment Your Weight Bench is designed and engineered to give you many hours of weight conditioning This manual is provided to help you understand the simple assembly adjustments and use of the Weight Bench In addition to assembly instructions it also contains conditioning guides maintenance tips and parts information Please take the time to read all the information contained in this manual and after assembly is completed keep it for future reference WARNING reduce the risk of serious injury read the important safety precautions before using this equipment 1 Read all instructions in this manual before using this equipment 2 Usethis equipment only as described in this Owner s Guide 3 Inspect and tighten all parts each time this equipment is used Replace any worn parts immediately 4 Keep hands away from moving parts other than the designated handles 5 Keep small children away from this equipment during use WARNING Before beginning this or any exercise program consult your phys
8. INSIDE 61 into the upper end of the LEG EXTENSION 8 Position the LEG EXTENSION 8 between the Leg Extension Brackets on the MAIN FRAME 3 Secure using a 3 8 X 2 1 2 HEX HEAD BOLT 46 to bolt through the Bracket and then through the Leg Extension Secure with a 3 8 NYLON LOCK NUT 45 DO NOT OVER TIGHTEN OR THE LEG EXTENSION WILL NOT BE ABLE TO SWING FREELY Select the WEIGHT BAR 10 a round tube 1 in diameter and 12 long with a hole in the center Press 1 ROUND PLASTIC INSERT CAPS 59 into the ends of the tube Assemble the Weight Bar into the large hole at the very end of the LEG EXTENSION 8 Align the bolt holes and secure using a 5 16 X 1 3 4 EYELET BOLT 34 to through the top of the Leg Extension and then through the Weight Bar Secure with a 5 16 NYLON LOCK NUT 30 Select the two PAD BARS 9 round tubes 3 4 in diameter and 13 1 4 long Press 3 4 ROUND PLASTIC INSERT CAPS 58 into both ends of the tubes NOTE 7o each end of the PAD BARS 9 wipe a small amount of liquid dish detergent along the length of the Bars This helps in the assembly of the Foam Roller Pads When the detergent dries it acts as an adhesive Onto one end of each PAD BAR 9 press a3 X 5 1 2 FOAM ROLLER PAD 11 Assemble one PAD BAR 9 into the lower hole location on the LEG EXTENSION 8 Assemble another 3 X 5 1 2 FOAM ROLLER PAD 11 onto the opposite end of the Bar Assemble the other PAD BAR 9 into the hole locat
9. OCK NUT 30 Press 1 1 2 SQUARE PLASTIC INSERT CAPS 56 onto the ends of the BASE FRAME 2 7 Remove the backing from the UPRIGHT DECAL 80 and affix to the front of one side of the UPRIGHT 1 U BRACKET 39 31 iiu oi 4 39 4 0 6 E gee 30 PAGE 6 WEIDER SPORTING GOODS STEP 2 BACKREST amp SEAT ASSEMBLY 30 5 16 NYLON LOCK NUT 32 5 16 X 3 1 4 HEX HEAD BOLT 41 1 4 X 3 4 ROUND HEAD MACHINE SCREW 65 5 16 1 0 X 13 32 LONG METAL SPACER C the BACKREST 4 over to expose the threaded holes Position the LONG ANGLE IRONS 6 so that the flat side faces the inside of the Backrest Fasten with 1 4 X 3 4 ROUND HEAD MACHINE SCREWS 41 DO NOT COMPLETELY TIGHTEN THESE SCREWS AT THIS TIME J The bottom end the BACKREST 4 is the end that the LONG ANGLE IRONS 6 extend past This is the end that is assembled to the MAIN FRAME 3 straddle the LONG ANGLE IRONS 6 on the BACKREST 4 over the bolt hole location on the MAIN FRAME 3 Assemble a 5 16 X 3 1 4 HEX HEAD BOLT 32 into the large hole at the very end of one of the Long Angle Irons and then into a 5 16 X 13 32 LONG METAL SPACER 65 The Hex Head 4 Bolt will then go all the way through the Main Frame As the Bolt comes out of the Main Frame on the other side place another 13 32 LONG METAL SPACER 65 onto the Bolt and push the Bolt the rest of the way through into
10. ician This is especially important for individuals over the age of 35 or persons with pre existing health problems Read all instructions before using Weider assumes no responsibility for personal injury or property damage sustained by or through the use of this product SAVE THESE INSTRUCTIONS 1033 PART LIST UPRIGHT BASE FRAME MAIN FRAME BACKREST SEAT C1260 G01 G01 C4193 G01 G01 C4194 G01 G01 C1421 G01 G01 1422 001 601 C6293 GO1 GO1 C7312 G01 G01 4195 601 001 C7313 F01 GO1 7314 601 601 C0411 C04 G01 C6660 G01 G01 C6661 G01 G01 C4196 G01 G01 C4197 G01 G01 C7735 G01 G01 AA 8034 G01 10 jweeHrBAR tXIZ O n JFOAMROLLERPAD 3 X51 2 m jeE Loa 19 caBLE sHoRt O O 14 MasrToPsECTON i 1 5 MAsrBOTTOMsECTON ee CUN 0 NEM MEN ae FOAM GRIP 1 5 C0417 B05 G01 C4198 G01 G01 C4199 G01 G01 C7315 GO1 G01 C7316 G01 G01 C1261 G01 GO1 C6403 G01 G01 C1423 G01 G01 C6294 G01 G01 D up 616 X2 1 27 HEX HEAD BOLT 32 sne 1 4 HEX HEAD BOLT HH 5297 G01 jene 1 3 4 EYELET BOLT 5 16 X 2 CARRIAGE BOLT 5 16 ACORN NUT 5 16 X 5 HEX HEAD BOLT 5 16 X 2 HEX HEAD BOLT 5 16 X 2 1 4 HEX HEAD BOLT 1 4 NYLON LOCK NUT 1 4 X 3 4 ROUND HEAD MACHINE SCREW 1 4 X 2 ROUND HEAD MACHINE SCREW 1033 PART LIST HH 5088 G01 HH 5018 G01 HH 5068
11. ion on the upper LEG EXTENSION 8 Assemble another 3 X 5 1 2 FOAM ROLLER PAD 11 onto the opposite end of the Bar PAGE 8 WEIDER SPORTING GOODS STEP 4 ADJUSTABLE UPRIGHT ASSEMBLY 64 LOCKING EIN SMALL O insert the ADJUSTABLE UPRIGHT 24 into the UPRIGHT 1 QO oooo J L Use LOCKING PINS SMALL 64 to adjust the height of the ADJUSTABLE UPRIGHTS 24 J Press a 3 4 ROUND PLASTIC INSERT CAP 58 into the handle end of the 25 BACKREST ADJ BAR 25 Slide the Backrest Adj Bar into any of the hole 58 patterns on the UPRIGHT 1 This Bar is used to adjust the incline of the BACKREST 4 and the height of the ADJUSTABLE UPRIGHTS 24 when using the Backrest in jns incline position When the Backrest is the flat position the height of the Adjustable Uprights can be adjusted by the use of the LOCKING PINS SMALL 64 STEPS ARM CURL ASSEMBLY 26 41 1 4 X 3 4 ROUND HEAD MACHINE SCREW Assemble the ARM CURL PAD 26 to the PAD SUPPORT 27 using 1 4 X 3 4 ROUND HEAD MACHINE SCREWS 41 to bolt through s the Support and into 27 the Pad L To use the Curl Pad insert the PAD SUPPORT 27 into the top of the MAIN FRAME 8 and adjust to the desired height by inserting a LOCKING PIN SMALL 64 into the appropriate hole and allowing it to rest on top of the Frame You will need to use one of the Locking Pins from the Adjustable Uprights PAGE 9 WE
12. nufactured to the highest standards and that this product reaches the customer in the best possible condition In the event that you find any problem in workmanship or missing parts please call our toll free product service number 1 800 225 0653 Weider provides replacement parts at no charge to the customer for one year if it is determined that the part was defective from the manufacturer or if any part is missing from the original n opened carton If it becomes necessary to order replacement parts the following action and information is required 1 Your Owner s I D card must be returned to us to verify the product you have purchased your address and the date urchase charge ep acemeht parts will not be sent without this Information on file with our Parts Department 2 Parts may be ordered using the parts order card which Is Included wi this product or by calling our product service number 1 800 225 0653 Fie RSIS ST ES ORE PUES AK PDI heo following a Name of the product ULTRA MAX b Model number of product 1033 c Serial number of the product located on a decal on the frame See front cover for location of decal Ordering number of part See Parts List page e Description of the part from the Parts List page f Country of manufacturer See cover The same information is required when placing your order by mail If you need parts or assistance do not return this product
13. the opposite Long Angle Iron Secure with a 5 16 NYLON LOCK NUT 30 6 5 SEAT BRACKET TIGHTEN ALL SCREWS ON THE BACK OF THE BACKREST AT THIS TIME C Align the SEAT 5 onto the Seat Bracket on the MAIN FRAME 3 and attach with 1 4 X 3 4 ROUND HEAD MACHINE SCREWS 41 by bolting up through the Seat Bracket and then into the Seat PAGE 7 WEIDER SPORTING GOODS STEP 5 LEG EXTENSION ASSEMBLY First insert the WEIGHT PIN 7 through the angled hole the lower front of the LEG EXTENSION 8 Align the bolt holes and secure using a 5 16 X 2 HEX HEAD BOLT 38 to bolt through the Leg Extension and then through the Weight Pin Secure with a5 16 NYLON LOCK NUT 30 5 16 NYLON LOCK NUT 5 16 X 1 3 4 EYELET BOLT 5 16 X 2 HEX HEAD BOLT 3 8 NYLON LOCK NUT 3 8 X 2 1 2 HEX HEAD BOLT 1 ROUND PLASTIC COVER CAP 3 4 ROUND PLASTIC INSERT CAP L Place a 1 ROUND PLASTIC COVER CAP 15 57 over the rear extended portion of the WEIGHT PIN 7 Slide a WEIGHT 1 ROUND PLASTIC INSERT CAP STOP 71 flared side out over the Weight Pin until it is against 1 1 2 SQUARE PLASTIC INSERT CAP 240 the LEG EXTENSION 8 Frame Press 1 ROUND PLASTIC WEIGHT STOP f INSERT CAP 59 into the end of the tube LEG EXTENSION 58 9 BRACKETS lm few fe Insert 1 1 2 SQUARE PLASTIC INSERT CAP 240 14 16 GA WRITTEN
14. with a 3 8 NYLON LOCK NUT 45 LJ Drape the LONG CABLE 12 over the PULLEY 17 Cap the top of the MAST TOP SECTION 14 with 1 1 2 SQUARE PLASTIC INSERT CAP 56 L Press 1 ROUND PLASTIC COVER CAPS 9 1 Written Inside 59 A into each end of the LAT BAR 18 Apply a small amount of liquid dish detergent to each end of the Lat Bar and assemble the FOAM GRIPS 19 onto each end of the Lat Bar Thread a 5 16 NYLON LOCK NUT 30 onto an 5 16 X 1 3 4 EYELET BOLT 34 the way to the top of the threads and then insert the down through the top of the center hole in the LAT BAR 18 Secure with a 5 16 ACORN NUT 36 C inset S HooKS 70 through the one loop end of each CABLE 12 and 13 USING MAST ASSEMBLY STEP 1 ROWING AND CURLS Insert the Mast Assembly into the MAIN FRAME 3 Connect the loop of the LONG CABLE 12 into the 5 16 X 1 3 4 EYELET BOLT 34 on the LEG EXTENSION 8 Connect the S HOOK 70 end of the LONG CABLE 12 to the loop end of the SHORT CABLE 13 and then connect the S Hook end of the SHORT CABLE 13 to the LAT BAR 18 With this configuration Rowing and Curl Exercises may be performed Free weights can be loaded on either or both the WEIGHT PIN 7 or the WEIGHT BAR 10 STEP 2 LAT PULL DOWNS To do Lat Work either sitting or standing connect the LAT BAR 18 directly to the S HOOK 70 end of the LONG CABLE 12 Load weight on either the Leg Extension WEIGHT
Download Pdf Manuals
Related Search