Home

Weber Charcoal Grill 2 User's Manual

image

Contents

1. ection Annual Maintenance in your Owner s Manual If match lights burner check igniter see below Side Burner Maintenance AWARNING All gas controls and supply valves should be in the OFF position Check igniter Remove side burner cover To remove side burner cover remove control knob and screws that hold cover to bottom Figure 14 Make sure wire is connected between igniter and electrode Check that igniter lock nut is tight Figure 15 Note If the igniter works loose carefully tighten the igniter lock nut with an adjustable wrench or pliers Adjust igniter electrode Gap should be 1 8 to 3 16 inch from tip of electrode to burner Figure 16 Spark should be a white blue color not yellow Figure 14 Venturi Burner Igniter wire Electrode Igniter 3 16 gap
2. er control valve b Wait 5 minutes to let the gas clear before you try again or try to light with a match Genesis 4 models Figure 13 Note If you own a Genesis 4 the side burner will operate only when the Front burner is lit due to the FlameCheck Safety System 1 Open the side burner lid 2 Push down and turn the side burner control valve ON 3 Push the side burner igniter button several times so it clicks each time ACAUTION Side burner flame may be difficult to see on a bright sunny day AWARNING If the side burner does not light a Turn off the side burner control valve b Wait 5 minutes to let the gas clear before you try again or try to light with a match Figure 13 Side Burner Troubleshooting AWARNING Before attempting any troubleshooting steps all gas controls and supply valves should be in the OFF position Problem Side burner does not light Flame is low in high position Flame is very yellow in conjunction with the smell of gas OR Burner makes popping noise in conjunction with the smell of gas Push button ignition does not work Check Is gas supply off Is the Front burner on Genesis 4 Is fuel hose bent or kinked Inspect the Weber Spider Stopper Guard for possible obstructions Blockage of holes Does burner light with a match Cure Turn supply on Light Front burner Genesis 4 Straighten hose Clean the Weber Spider Stopper Guard See S
3. from the side burner fitting Figure 2 ACAUTION When removing the cap hold the side burner fitting to keep it from becoming loose If the side burner fitting should loosen tighten before attaching side burner hose Note After you complete this step skip Steps 5 and 6 and please go onto Step 7 Side burner fitting Brass cap Figure 2 MODELS WITH A BLACK SQUARE PIPE PLUG Using an adjustable wrench remove the pipe plug from the manifold Figure 3 EN Black pipe plug MODELS WITH A BRASS SQUARE PLUG Using an adjustable wrench remove the pipe plug from the manifold Figure 4 Brass square plug Figure 4 Step 5 FOR MODELS THAT USE THE ENCLOSED BRASS FITTING Apply pipe sealant to only the area indicated Figure 5 AWARNING Use a pipe sealant compound on the threads that is approved for natural or LP gas Only use pipe 7 sealant here NO pipe _ gt sealant here Figure 5 Screw the fitting into the manifold using the 5 8 inch wrench Figure 6 a Figure 6 a OR Screw the fitting into the brass plug elbow Figure 6 b Figure 6 b Step 6 Slide the side burner assembly into the open end of the right frame Route the side burner hose so that it parallels the front of the barbecue Loop the hose so that it reaches the side burner fitting Attach hose and tighten using the 3 4 inch wrench Figure 7 Install burner grate Check to be sure the side burner val
4. h side burner locks Slide the side burner toward the control panel The locks will snap into the slots in the front and back of the side burner Figure 11 ACAUTION Make sure both locks have snapped into place Y o Side view Figure 11 Lighting the Side Burner The side burner has a separate ignition system from the main cooking box ADANGER Failure to open lid while igniting the side burner or not waiting 5 minutes to allow gas to clear if the side burner does not light may result in an explosive flame up which can cause serious bodily injury or death Note If you own a Genesis 4 the side burner will operate only when the Front burner is lit due to the FlameCheck Safety System Follow steps for Genesis 4 models Genesis 2 and 2000 models Figure 12 1 Open the side burner lid 2 Check that the fuel scale reads more than E 3 Check that the side burner valve is OFF push down and turn clockwise and all main burner control valves are OFF push down and turn clockwise 4 Turn the LP tank valve ON turn counterclockwise 5 Push down and turn the side burner control valve ON 6 Push the side burner igniter button several times so it clicks each time Figure 12 ACAUTION Side burner flame may be difficult to see on a bright sunny day AWARNING If the side burner does not light a Turn off the side burn
5. ve is OFF Push side burner control knob down and turn clockwise Step 7 CHECK FOR GAS LEAKS Remove the control knob and two screws holding the side burner cover to the bottom Figure 8 Figure 8 ADANGER Do not use an open flame to check for gas leaks Be sure there are no sparks or open flames in the area while you check for leaks This will cause fire or an explosion which will result in serious bodily injury or death and damage to property Use a soap and water solution Turn on gas supply Follow the gas leak check procedures in your Owner s Manual Check side burner hose to manifold connection a and connection inside side burner b Figure 9 if you own a Genesis 2 and 2000 Gas Barbecues or Figure 10 if you own a Genesis 4 Gas Barbecue If bubbles should appear at connection a turn OFF gas supply tighten fitting and recheck AWARNING If bubbles should appear at connection b turn OFF the gas DO NOT OPERATE THE SIDE BURNER Contact your dealer After leak checks are complete reinstall the control panel and valve control knobs If you own a Genesis 4 Gas Barbecue don t forget to reinstall the FlameCheck Safety button Genesis 2 and 2000 Models Figure 9 Figure 9 Genesis 4 Models Figure 10 To secure the side burner follow this instruction Make sure both locks have snapped into place Secure side burner Stand to the right side of the barbecue Slightly pull back bot
6. wel For use with Genesis Gas Barbecues Only Step 1 AWARNING All gas controls and supply valves should be in the OFF position You will need Side burner assembly includes burner grate side burner lock pipe sealant suitable for natural or LP gas 1 4 7 16 5 8 3 4 and 11 16 inch open end or two adjustable wrenches Step 2 Genesis 2 and 2000 Models Remove the right side work table burner control knobs and control panel Genesis 4 Models Remove the right side work table serving tray burner control knobs FlameCheck Safety button and control panel Genesis Side Burner Accessory Installation Step 3 Note Your owner s manual may reflect installing only one side burner lock If it does please ignore and follow this installation procedure for two side burner locks You will need frame assembly two side burner locks and a 7 16 inch wrench Loosen the right rear 1 4 x 20 bolt Install the side burner lock The U shape cut out of the lock slips down over the bolt Tighten with a wrench Figure 1 a Loosen the right front 1 4 x 20 bolt The side burner lock fits between the front panel and the frame The U shape cut out slips up over the bolt Tighten with a wrench Figure 1 b Figure 1 Follow the remainder of assembly steps in your Owners Manual 27 4736910 3 98 Step 4 SIDE BURNER GAS CONNECTIONS MODELS WITH A BRASS CAP Using two adjustable wrenches remove the brass cap

Download Pdf Manuals

image

Related Search

Related Contents

取扱説明書保証書付 - ご家庭のお客さま/大阪ガス  SoftBank 202SH 取扱説明書 - モバイル  RASTO DO FUNDADOR - Corpo Nacional de Escutas  取扱説明書 - パナソニック  Bedienungsanleitung BBA462 / BBK462  Instructions  M-Powered Basics Guide_J - akmedia.[bleep]digidesign.  NWKSP3 - ComNet  603000 603001 - Harvard Apparatus  Explorer Group Motorhomes Avantgarde  

Copyright © All rights reserved.
DMCA: DMCA_mwitty#outlook.com.