Wayne-Dalton 3990-372 User's Manual
Contents
1. Wiring 1 Disconnect power to the door or gate operator before proceeding WARNING To prevent electrical shock be sure electrical power is disconnected before proceeding with wiring 2 Connect the enclosed twin lead wires to the terminals labeled RLY use only 22 AWG or larger CL2X or better 3 Connect other end of twin lead wires to door or gate opener s control input 4 Connect power to the two terminals labeled PWR Receiver requires 10V to 28V AC or DC Connect Antenna Direct Connect Antenna Attach antenna as shown For best reception keep antenna wire straight and away from metal objects Antenna Extension Kit Optional 1 Connect extension wire to receiver 2 Route wire outside metal enclosure Route and secure wire away from moving parts 3 Mount antenna holder outside enclosure 4 Screw antenna to extension wire NOTICE Do not route coax wire near any moving parts of the operator If necessary secure coax wire away from any moving parts 5 Position antenna wire straight For best reception keep antenna away from metal PWR NON POLARIZED PWR RLY Door or Gate control input2. P O Box 67 Mt Hope OH 44660 888 827 3667 Radio Receiver Models 3990 372 3994 433 Installation Instructions and Owner s Manual Radio Receiver Specifications NOTICE Dry Locations Only e INPUT POWER Non polarized input connection 10 to 28 VDC 40 mA with relay off 60 mA with relay active 10 to 28 VAC 40 mA with relay off 90 mA with relay active NOTICE Class 2 product for voltages 32 VAC DC or less O RELAY OUTPUT CONTACTS Normally open dry contacts non polarized connection Switching current capability 1 0 mA to 0 5 A at 10 to 28 VAC and 2 0 mA to 1 0 A at 10 to 28 VDC Model 3990 372 372 5 MHZ Model 3994 433 433 92 MHz Model 3990 372 7 2 inch Model 3994 433 5 8 inch Capable of learning 14 transmitters any combination of portable transmitters RF wall stations or RF keypads IMPORTANT NOTICE Read the enclosed instructions carefully before installing this radio receiver Pay close attention to all warnings and notes This manual should be retained for future reference Copyright 2007 Wayne Dalton Corp Part No 318705 Rev 3 7 9 2007 Package Contents 1 Receiver 2 Antenna 3 Twin lead wire 6 feet 4 Manual Optional Accessories 1 Power Adapter 2 Antenna Extension Kit Definition of Symbol Warning Installation Safety Precautions WARNING INCORRECT INSTALLATION CAN LEAD TO SEVERE OR FATAL INJURY FOLLOW THESE INSTRUCTIONS CAREFULLY READ and FOLLOW all instal
3. Possible near by radio interference 4 With transmitter Check relay RLY wire connections In activation the receiver s sure relay wire is not broken or damaged STATUS LED lights and Insure relay wire is connected to proper a click is heard within terminals on operator Using insulated receiver but receiver does pliers or insulated screwdriver short RLY not activate operator terminals on receiver and this should activate operator Test operator for proper operation 5 Can not learn transmit Insure transmitter is a correct transmitter ter for this receiver Check this receiver s RF frequency and the companion transmitter s frequency to insure they are identical Test receiver with another transmitter FCC and IC Statement FCC Regulatory Information This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation IC Regulatory Information Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device NOTE This equipment has been tested and found to comply with limits for a Class B digital device pursuant to Part 15 of FCC Rules These limi
4. To Erase All Learned Transmitters 1 Press and hold down the PROGRAM button 2 After 10 seconds the red STATUS LED will blink 5 times indicating all transmitters are erased from the receiver s memory 3 Release the PROGRAM button 4 Re learn transmitters as needed following the above Programming instructions Safe Operation Precautions WARNING To reduce the risk of severe or fatal injury 1 Always keep a moving door or gate in sight and keep people and objects away until it is completely opened or closed No one should cross the path of a moving door or gate Never let children operate or play with the controls Keep all controls away from children Never go under a stopped partially open door Never walk through a vehicular entry gate always use the pedestrian entry Keep fingers and other body parts away from the all moving parts of the door gate and operator system while the system is being operated Periodically test the safety systems of the door or gate Disconnect and do not use this receiver if any of your door or gate s safety systems fail their tests Then have door or gate operator serviced immediately 7 SAVE THESE INSTRUCTIONS Operation Whenever this receiver senses a valid signal from a learned transmitter the relay will activate for one second and therefore activate the operator 1 Press and release selected button on Wayne Dalton transmitter 2 Receiver LED will light and the unit will cyc
5. Connect Power Source If powered by Power Supply Plug power supply into source If powered by Operator Connect wires to the proper operator accessory supply source 10 V AC DC to 28 V AC DC source 1 Re connect power to the door or gate operator 2 Using wall control activate door or gate operator to confirm power connection Programming WARNING Keep away from all high voltage contacts while servicing receivers WARNING During programming door or gate operator will acti vate Keep people and objects away from door or gate 1 Test receiver by operating a compatible RF transmitter The Receiver s STATUS LED will flash indicating reception PROGRAM BUTTON 2 Press and release the RED STATUS LED receiver s PROGRAM button once The receiver s red STATUS LED will turn on and remain on for 25 seconds indicating that the receiver is ready to learn a transmitter 3 Press the button on the transmitter you wish to use to control the operator The receiver s red STATUS LED will turn on and off three times indicating a successful learn 4 Press the same button on the transmitter once more to confirm operation of the door or gate operator 5 Test range of transmitter Repositioning antenna may provide greater range 6 Repeat Transmitter Programming steps for additional transmitters
6. ICED UNDER NORMAL USE AND SERVICE THE ABOVE CONDITIONS APPLY PROVIDED THAT THE ABOVE REFERENCED RADIO RECEIVER MODEL 3990 372 3994 433 IS PROPERLY INSTALLED USED MAINTAINED AND SERVICED IN ACCORDANCE WITH THE MANUFACTURER S INSTALLATION AND OPERATING INSTRUCTIONS UNDER NORMAL USE AND SERVICE THIS LIMITED WARRANTY EXTENDS ONLY TO THE ORIGINAL PURCHASER PROVIDED THE ABOVE REFERENCED RADIO RECEIVER IS PROPERLY INSTALLED USED MAINTAINED AND SERVICED THIS LIMITED WARRANTY IS NOT TRANSFERABLE NO EMPLOYEE DISTRIBUTOR OR REPRESENTATIVE IS AUTHORIZED TO CHANGE THE FOREGOING WARRANTIES IN ANY WAY OR GRANT ANY OTHER WARRANTY ON BEHALF OF MANUFACTURER THE MANUFACTURER SHALL NOT BE RESPONSIBLE FOR ANY DAMAGE RESULTING TO OR CAUSED BY ITS PRODUCTS BY REASON OF INSTALLATION IMPROPER STORAGE UNAUTHORIZED SERVICE ALTERATION OF PRODUCTS NEGLECT OR ABUSE ANY ACTS OF NATURE BEYOND MANUFACTURER S CONTROL SUCH AS BUT NOT LIMITED TO LIGHT NING POWER SURGES WATER DAMAGE ETC OR ATTEMPT TO USE THE PRODUCTS FOR OTHER THAN THE CUSTOMARY USAGE OR FOR THEIR INTENDED PURPOSES THE ABOVE WARRANTY DOES NOT COVER NORMAL WEAR OR ANY DAMAGE BEYOND MANUFACTUR ER S CONTROL OR REPLACEMENT LABOR CLAIMS FOR DEFECTS IN MATERIAL AND WORKMANSHIP COVERED BY THIS WARRANTY SHALL BE MADE IN WRITING WITHIN THE WARRANTY PERIOD TO THE DEALER TO WHOM THE PRODUCT WAS PURCHASED MANUFACTURER MAY EITHER SEND A SERVICE REPRE SENTATIVE OR HAVE THE PRODUCT RETU
7. RNED TO THE MANUFACTURER AT BUYER S EX PENSE FOR INSPECTION IF JUDGED BY MANUFACTURER TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP THE PRODUCT WILL BE REPLACED OR REPAIRED AT THE OPTION OF THE MANUFACTURER FREE FROM ALL CHARGES EXCEPT AUTHORIZED TRANSPORTATION AND REPLACMENT LABOR THE REMEDIES OF BUYER SET FORTH HEREIN ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER REMEDIES THE LIABILITY OF MANUFACTURER WHETHER IN CONTACT TORT UNDER ANY WARRANTY OR OTHERWISE SHALL NOT EXTEND BEYOND ITS OBLIGATION TO REPAIR OR REPLACE AT ITS OPTION ANY PRODUCT OR PART FOUND BY MANUFACTURER TO BE DEFECTIVE IN MATERIAL OR WORK MANUFACTURER SHALL NOT BE RESPONSIBLE FOR ANY DIRECT INDIRECT SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE HOWEVER SOME STATES DO NOT ALLOW LIMI TATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLU SIONS MAY NOT APPLY TO YOU Questions Need Information Call Us Toll Free 888 827 3667 Thank you for your purchase www waynedalton com Please Do Not Return This Product To The Store Call Us Directly Our Trained Technicians Will Answer Your Questions and or Ship Any Parts You May Need
8. lation instructions 1 Before installing this receiver read the door or gate operator s instruction manual fully so you are aware of all of the unit s functions and features 2 Wear protective gloves to install repair or adjust door gate or operator to avoid hand injuries 3 Wear eye protection when using tools to install repair or adjust door gate or operator to prevent eye injuries 4 Mount control buttons within sight of door or gate at a minimum height of 5 ft so small children cannot reach them Keep control buttons away from all moving parts of a door and at least 6 ft away from all moving parts of a gate or its operator 5 Before installing receiver disconnect all power to door or gate operator to prevent unintended operation 6 Do not connect this receiver to a power source until instructed to do so Do not reconnect power to the door or gate operator until instructed to do so 7 Only install receiver on a properly functioning door or gate operator 8 Installation and wiring must comply with local building and electrical codes This product is not intended and must not be installed in a explo sive environment 9 Pay close attention to all warnings notices and notes in these instructions 10 To prevent electrical shock and or fire hazards do not connect this receiver to any voltages greater than 32 VAC or DC WARNING After installing and testing this receiver test all safety features of you
9. le Maintenance Disconnect electric power to door or gate operator before making repairs or removing case covers While this receiver is maintenance free periodic cleaning of the receiver case is suggested To clean the receiver case disconnect power to receiver and operator and then use a soft cloth to remove any dirt and dust Service Unit contains no user serviceable parts Contact your dealer or Wayne Dalton customer support for additional information To Remove This Receiver From Service 1 Disconnect power to operator door operator gate operator etc and disconnect power to this receiver 2 Disconnect all wiring connected to receiver Disconnect antenna and any associated coax wiring 3 Remove receiver from mounting location Discard properly per local codes 4 Reconnect power to operator Test operator for proper operation Trouble Shooting Symptom Possible Solution 1 Receiver s red STATUS Check power source to receiver Insure LED does not turn on proper 10 VAC DC minimum to 28 VAC when programming button DC maximum power source pressed 2 No transmitter range less than 10 ft Check antenna connections and if in stalled check antenna extension kit coax wire for damage or kinks Correct antenna connection or replace coax as needed 3 Poor transmitter range Insure antenna is not near any metal Re less than 50 ft position antenna from vertical to horizontal position or vice versa
10. r door or gate s operator Disconnect this receiver if any of your door or gate s safety system features fail to function properly Then have your door or gate operator serviced immediately by a qualified person You can reach us Toll Free 1 888 827 3667 for Consumer Preliminary Operator Tests 1 Make sure door or gate operator has been properly installed in accordance with unit s installation instructions 2 Test and confirm proper operation of the door or gate operator before proceeding with the installation of this receiver A WARNING Keep fingers and other body parts away from all moving parts of the door and gate operators system while the system is being operated WARNING To prevent unintended operation disconnect power to the door or gate operator after completing the above preliminary operator Mounting A WARNING Do not connect electrical power to this receiver until instructed to do so A WARNING Disconnect electric power to door or gate operator before making repairs or removing case covers 1 Select a location four to six feet from other receivers Receiver can be attached to metal wood or plastic surfaces 2 Use screws or other fastening means to attach receiver 3 If receiver is mounted inside a metal enclosure use an antenna extension kit optional to extend the antenna outside of the enclosure ssistance or online at www wayne
11. ts are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with these instructions may cause harmful interference to radio communication however there is no guarantee that interference will not occur in a particular installa tion If this equipment does cause harmful interference to radio or television reception which can be determined by turning equipment off and on user is encouraged to try to correct interference by one or more of the following measures Reorient or relocate receiving antenna Increase separation between equipment and receiver Connect equipment into an outlet on a circuit different from that which receiver is connected Consult your dealer or and experienced radio television technician for help WARNING Changes or modifications to this unit not expressly approved by party responsible for compliance could void user s authority to operate this equipment Q You can reach us Toll Free 1 888 827 3667 for Consumer Assistance or online at www wayne dalton com RADIO RECEIVER LIMITED WARRANTY THE MANUFACTURER WAYNE DALTON CORP WARRANTS ALL COMPONENTS OF THE RADIO RECEIVER MODEL 3990 372 3994 433 FOR A PERIOD OF 90 DAYS FROM THE TIME OF INSTALLATION AGAINST DEFECTS IN MATERIALS AND WORKMANSHIP PROVIDED IT IS PROPERLY INSTALLED USED MAINTAINED AND SERV
Download Pdf Manuals
Related Search