Vision Fitness T9800 User's Manual
Contents
1. use2. Z Aun 9 Ayuons Z Ayuone Z Agun JOYSD A UY 1ZXE X9 PDE 1900S 1 1 X OW POSH 104 I X SW P2H sdiyiug IZ L X SW sBOg SIOMPIDH pepoo iojop LAO Asy jouBoyy Ajeyos Z AID s9400 IOGe pun LAO Spog 1940M X04 SLUWd Eao y Aqjuons PNA B RES O O y Auons g UDIO 7 AMON JOYsOMA Ild LZXSL TOL 19YSOM I4 1ZXG LXZ B JOYS AA IO 4 LCX6 LXC 8 y u g Ayuons p Among ieg ISL XOLW PDH 8905 I X BW Pda 194905 I x BW Ce ee JOA PMEIOS yous pedoys ww yous pedoys ww 9V4 1N14 Yyousi A pedoys wwg GIGNTINI JAVMaYVH GIGNIINI SLYVd 8 JYVMGYVH S1001 STEP 4 AUTO CALIBRATION DO NOT STAND ON THE BELT WHEN PERFORMING AUTO CALIBRATION You need to access User Engineering Mode to run the auto calibration With the safety key in place please ho down SPEED DOWN and SELECT for 5 seconds When in the User mode USER ENG MODE appears in th alphanumeric window To access the data press the ELEVATION keys until AUTO CALIBRATION appears To begin auto calibration press SELECT The treadmill will run through minimum and maximum speed an maximum incline This will take 3 5 minutes Let the treadmill perform this complete function before exiting th Engineering Mode Elevation A D appears in the left window PVVM value appears in the dot matrix window and speed
3. appears in he right window CALIBRATION PASSED will appear in the alphanumeric window when the auto calibration is complete The treadmill will come to a complete stop and return to the startup screen in the alphanumeric window U VISIONN FITNESS 500 South CP Avenue PO Box 280 Lake Mills WI 53551 toll free 800 335 4348 phone 920 648 4090 fax 920 648 3373 T9800 Sertes www visiontitness com TREADMILLS 2005 Vision Fitness All Rights Reserved 10 05 AG18 39PRD REV2 U VISIONS FITNESS Assembly Guide T9800 Sertes TREADMILLS To avoid possible damage to this Platform Treadmill please follow these assembly steps in the correct order Before proceeding though find your new Platform Treadmill s 2 serial numbers located on the underside of the main frame and on the bottom of the console and enter here Frame Serial Number Console Serial Number Refer to these numbers when calling for service and also enter these serial numbers on your Warranty Card and in your own records Be sure to read your Owner s Guide before using your new Platform Treadmill If any parts hardware or tools are missing please call 1 800 335 4348 Extension 12 NOTE It is recommended that you apply grease to the threads of each bolt as you assemble your Platform Treadmill to prevent loosening and noise Also during each assembly step ensure that ALL nuts and bolts are in place and partially threaded in before complet
4. d a bolt M6x15L socket head amp an arc washer 6x13x2T into the two holes of the console plastic and a bolt M8x15L flat head into the hole in the handlebar Fasten a bolt M6x15L socket head and a flat wash er 6x20x21 into the hole in the handle bar on the console mast Do not fully tighten the bolts e Slide the handlebar cover over the bracket and secure with a bolt M6x15L socket head and a flat washer 6x16x2T Do not fully tighten the bolt e Repeat on the left side e Fully tighten the console and handlebar bolts MOTOR COVER e Place the motor cover back on the frame and fasten with 6 screws e Attach the power cord to the treadmill e Plug the power cord into the power outlet AUTO CALIBRATION Please refer to back cover for this procedure then return to Step 6 BELT TENSION e If the running belt slips when used run the treadmill at 2 0 mph and use the supplied 8mm Allen wrench to turn the left and right tension bolts clockwise V turn at a time until the belt no longer slips e f the running belt is too far to the right side run the treadmill at 2 0 mph and use the supplied 8mm Allen wrench to turn the right tension bolt clockwise 4turn at a time until the belt remains centered during use If the running belt is too far to the left side run the treadmill at 2 0 mph and turn the left tension bolt clockwise V a turn at a time until the belt remains centered during
5. ely tightening any ONE bolt e Remove motor cover screws and take off the motor cover e Insert the right console mast to the right console mast bracket First fasten the inside of the console mast to the console mast bracket by securing four bolts M8x15L socket head and four washers 8 2x19x2T Fully tighten the bolts Second fasten the two bolts M10x15L button head and two washers 10 2x19x2T on the front of the console mast and fully tighten e Repeat on the left side STEP 2 BLUE BAG e Tie the ribbon data cable to the cable wire tie on the top of the right console mast Feed the ribbon cable down the console mast and through the hole at the lower part of the console mast Push any remaining cable into the console mast e Mount the console onto the left and tight console masts using four bolts M8x15L socket head and four washers 8 2x19x2T Do not fully tighten e Take the wire tie off the ribbon cable Plug the large 20 pin ribbon connector into the 20 pin connector on the lower control board Attach the grounding wire connector to the grounding wire located in the motor pan near the front of the frame Insert the handlebar cover onto the handlebar Insert the right handlebar by holding the handlebar sideways toward the treadmill and inserting the top into the console Rotate the handlebar into the bracket located on the console mast Fasten with a bolt MS5x1 21 an
Download Pdf Manuals
Related Search