Viking F20022J EN User's Manual
Contents
1. assy N va Py 24 4 cm Model__ DEWD170 _ DEWD100 25 1 4 28 1 4 A 64 1 cm 71 8 cm CABINET INSTALLATION eTo remove drawer assembly pull warming drawer pan out until fully extended Slide finger along the right and left side until you reach the black hand latches located at the front of the rails Pull up on both the right and left latches and pull drawer pan support completely out Slide cavity assembly into cabinet opening Drill 4 pilot holes in cabinet using 1 8 drill bit Permanently secure the warming drawer using the 4 8 mounting screws provided eReplace drawer assembly o B OOOO Nr FRONT 10 25 4 cm REAR 120V Electrical opening 2 1 2 LZ When facing cabinet opening is 6 4 cm 1 located on right side j o o SIDE 11 2 3 8 em eee Ta 23 58 4 cm Lg oe peo en ea I DEWD170 DEWD100 26 1 2 67 3 cm 29 1 2 74 9 cm 24 7 8 63 2 cm 27 7 8 70 8 cm 18 7 8 47 9 cm 21 7 8 55 6 cm 5 7 16 13 8 cm 5 7 16 13 8 cm 21 3 16 53 8 cm 21 3 16 53 8 cm 80 Ib 36 kg 90 Ib 40 5 kg DFWD CABINET CUTOUT Cabinet ee ae Mounting Screws 4 8 x 3 4 Cavity Assy 6 8 x 3 4 screws to attach custom front 1 l I I I l insulation custom front i Fag Model ___ DFWD170 _ DFWD100 25 1 4 A 64 1 cm CUSTOM FRONT INSTALLATION eOpen the drawer and remove the pan eCenter th2. max amps eDEWD100 DFWD100 475 watts 4 0 max amps
3. Viking Installation Guide Viking Range Corporation 111 Front Street Greenwood Mississippi 38930 USA 662 455 1200 For product information call 1 888 VIKING1 845 4641 or visit the Viking Web site at vikingrange com Designer Series Built In Electric Warming Drawer GF DEWD Designer Model DFWD Full Overlay Model US F20022J EN 022608J IMPORTANT PLEASE READ AND FOLLOW Before beginning please read these instructions completely and carefully Do not remove permanently affixed labels warnings or plates from the product This may void the warranty Please observe all local ordinances If local codes are applicable wire in accordance with the National Electrical Code ANSI NFPA 70 latest edition eWARNING To reduce the risk of electric shock and fire do not use a flexible power supply cord with this appliance The installer should leave these instructions with the consumer who should retain for local inspector s use and for future reference WARNING Make sure that incoming voltage is the same as unit rating An electric rating plate specifying voltage hertz wattage amps and phase is attached to the product Wiring the warming drawer with more voltage than it is rated for may cause severe damage to the thermostat element and other components Wiring the warming drawer with less voltage than it is rated for may cause significant decrease in performance To reduce the risk of fire electric shock o
4. e custom front and insulation around the inside panel NOTE Make sure the insulation provided is used between the custom panel and the inside door panel eAttach the custom front with the 6 six 8 x 3 4 screws provided CABINET INSTALLATION eTo remove drawer assembly pull warming drawer pan out until fully extended Slide finger along the right and left side until you reach the black hand latches located at the front of the rails Pull up on both the right and left latches and pull drawer pan support completely out Slide cavity assembly into cabinet opening Drill 4 pilot holes in cabinet using 1 8 drill bit Permanently secure the warming drawer using the 4 8 mounting screws provided eReplace drawer assembly CUSTOM PANEL DIMENSIONS l 3 4 thick FRONT N 10 1 2 26 7 cm L J REAR 120V Electrical opening f 9 1 2 24 1 cm gaja r When facing cabinet opening is located on right side 6 4 cm a 7 8 55 6 cm gt 23 1 4 58 7 cm oo 2 1 2 6 4 cm U i DFWD170 DFWD100 27 7 8 70 8 cm 187 8 47 9 cm 7 8 47 9 cm 21 EA 55 6 cm 5 7 16 13 8 cm 57 16 13 8 cm 13 8 cm 21 3 16 53 8 cm 21 3 16 53 8 cm 75 Ib 33 7 kg 90 Ib 40 5 kg ELECTRIC DATA eHard wire direct with separate 15 amp minimum 2 wire with ground circuit e120 VAC 50 60 Hz eDEWD170 DFWD170 425 watts 3 6
5. r injury to persons installation work and electrical wiring must be done by qualified people in accordance with all applicable codes and standards including fire rated conditions GENERAL INFORMATION eTHIS UNIT IS NOT TO BE INSTALLED BELOW CABINETS OR WALL MOUNTED eWhen installing this unit directly below other units only install with Viking built in products Remove warming drawer carefully from carton Remove all loose packaging and accessories elt is the responsibility of the installer to comply with local codes If no local codes are applicable wire in accordance with the National Electrical Code ANSI NFPA 70 latest edition This appliance is not fused Protect with a proper sized fuse or circuit breaker eLine disconnect switch circuit breaker or plug receptacle of power cord connection should be readily accessible to the operator eGround unit per applicable electrical codes eAny installation not matching the specifications discussed in these instructions will void the manufacturer s warranty ELECTRICAL CONNECTION USE COPPER CONDUCTORS ONLY With the appliance positioned in front of the cabinet opening connect wire leads extending from the power supply to the terminal block of the unit Make sure the colored wires of the terminal block are connected to the corresponding colored wires extending from the power supply DEWD CABINET CUTOUT wae Cabinet 24 61 0 cm mounting screws 4 cavity d rawer NN
Download Pdf Manuals
Related Search