Viking DFUR154 User's Manual
Contents
1. 37 3 16 94 5 cm SPECIFICATIONS DIMENSIONS Front View DESIGNER SERIES Basic Electric Data e115 VAC 60 Hz eMaximum amps 3 0 eApproximate shipping weight 110 Ibs 49 5 kg Min 34 1 4 87 0 cm to Max cis 88 9 cm with leveling legs fully extended 30 3 4 78 1 cm Sees ees ees e 14 2 4 37 5 cm gt Side View DUAR Side View DFUR 37 3 16 94 5 cm lt 37 3 16 94 5 cm 2 3 16 53 8 cm gt 21 3 16 53 8 cm lt lt 23 5 8 60 0 cm gt lt 237 16 59 5 cm 24 5 8 62 5 cm gt to front of locally supplied custom panel GENERAL INFORMATION Unpack 1 Remove banding from bottom of carton Lift carton up and off of the refrigerated beverage center 2 Remove all tape and packaging material from the outside and inside of the cabinet 3 Keep all carton packaging until your refrigerated beverage center has been thoroughly inspected and found to be in good condition AREA REQUIREMENTS Units Certified for Indoor Use black outer cabinet 1 Place unit so the front side will be completely unobstructed to provide proper air flow The unit may be closed in on the top and three sides but the front MUST BE unobstructed for air circulation and proper operation Installation should be such that the cabinet can be moved for servicing if necessary 2 Unit should be in a well ventilated2. _ESSSSSSSSSSSSSSSS Serial Number Date of Purchase Date Installed Dealer s Name Address If service requires installation of parts use only authorized parts to ensure protection under the warranty This manual should remain with the refrigerator for future reference 13 UNDERCOUNTER FREESTANDING REFRIGERATED BEVERAGE CENTER WARRANTY Units certified for Outdoor Use ONE YEAR FULL WARRANTY Built in freestanding undercounter refrigerated beverage centers and all of their components and accessories except as detailed below are warranted to be free from defects in material or workmanship under normal household use for a period of one 1 years from the date of original retail purchase Viking Range Corporation warrantor agrees to repair or replace at its option any part which fails or is found to be defective during the warranty period Painted and decorative items are warranted to be free from defective materials or workmanship for a period of ninety 90 days from the date of original retail purchase ANY DEFECTS MUST BE REPORTED TO THE SELLING DEALER WITHIN NINETY 90 DAYS FROM DATE OF ORIGINAL RETAIL PURCHASE FIVE YEAR LIMITED WARRANTY Any sealed refrigeration system component as listed below is warranted to be free from defective materials or workmanship in normal household use during the second through the fifth year from the date of original retail purchase Viking Range Corporation warrantor agrees to
3. Move the bottom right hinge bracket to the upper left side of the cabinet and fasten it in place with its original mounting screws 3 Install the hinge door swing pin into the top right hinge bracket and move the bracket to the lower left side of the cabinet Fasten it in place with its original screws 4 Place the plastic washer over the bottom door swing pin on the top surface of the bottom left hinge 5 Position the door on the bottom left hinge pin and push the door under the top left hinge 6 Line up the top left hinge hole with the door bushing hole and insert swing pin Screw down the door swing pin with the 1 8 allen drive unit until its head is flush with the top surface of the top left hinge i ee Bottom hinge 7 Reposition the logo Your installation is now complete bracket Note Hinge bracket location shown is for right hinge swing Light switch activator CUSTOM WOOD FRAME INSTALLATION INSTRUCTIONS DFUR Model Note Weight of wood panel must not exceed 20 Ibs Wood Screws 1 A 10 pan head wood screw should be used to properly secure the wood frame A total of 8 screws will be needed for a 3 1 2 8 9 cm kickplate or 7 screws for a 4 10 2 cm kickplate 2 Only use pan head screws 3 DO NOT select a screw that is longer than the wood thickness at Working Material Wood Screw Size 10 the screw locations Hardwood 3 32 0 24 cm 4 Use recommended pilot holes for the frame material See cha
4. area with temperature above 55 F 13 C and below 110 F 43 C Best results are obtained at temperatures between 65 F 18 C and 80 F 27 C for built in models and between 65 F 18 C and 90 F 32 C for freestanding models 3 Provisions for electricity should be determined before placing unit in proper place Units Certified for Outdoor Use stainless steel outer cabinet MUST BE INSTALLED IN AN AREA PROTECTED FROM THE ELEMENTS SUCH AS WIND RAIN WATER SPRAY OR DRIP 1 Place unit so the front side will be completely unobstructed to provide proper air flow The unit may be closed in on the top and three sides but the front MUST BE unobstructed for air circulation and proper operation Installation should be such that the cabinet can be moved for servicing if necessary 2 Unit should be in a well ventilated area with temperature above 40 F 4 C and below 110 F 43 C 3 Provisions for electricity should be determined before placing unit in proper place Door swing pin Top hinge bracket REVERSIBLE DOOR Glass Door Units Only PROFESSIONAL SERIES You can change the door swing from right to left hinge very easily 1 Simply unscrew the top hinge door swing pin with an 1 8 allen drive unit and lift door off of the bottom hinge bracket Flip the door remove the light switch activator and replace the light switch activator on the other end of the door 2 Remove the door swing pin from bottom right hinge
5. original retail purchase will be repaired or replaced free of charge for the part itself with the owner paying all other costs including labor NINETY 90 DAY RESIDENTIAL PLUS WARRANTY This warranty applies to applications where use of the product extends beyond normal residential use Examples are but not limited to bed and breakfasts fire stations private clubs churches etc This warranty excludes all commercial locations such as restaurants food service locations and institutional food service locations This warranty extends to the original purchaser of the product warranted hereunder and to each transferee owner of the product during the term of the warranty This warranty shall apply to products purchased and located in the United States and Canada Products must be purchased in the country where service is requested Warranty labor shall be performed by an authorized Viking Range Corporation service agency or representative Warranty shall not apply to damage resulting from abuse accident natural disaster loss of electrical power to the product for any reason alteration improper installation improper operation or repair or service to the product by anyone other than an authorized Viking Range Corporation service agency or representative Warranty shall not apply to damage resulting from indoor units being used in outdoor situations This warranty does not apply to commercial usage Warrantor is not responsible for consequential or inci
6. Recommended Grounding Methods For your personal safety this refrigerated beverage center must be grounded This appliance is equipped with a 7 2 1m power supply cord having a 3 prong grounding plug To minimize possible shock hazard the cord must be plugged into a mating 3 prong grounding type wall receptacle grounded in accordance with the National Electrical Code and local codes and ordinances If the circuit does not have a grounding type receptacle it is the responsibility and obligation of the customer to exchange the existing receptacle in accordance with the National Electrical Code and applicable local codes and ordinances The third ground plug SHOULD NOT under any circumstances be cut or removed All UL listed refrigerated products are equipped with this type of plug FINAL PREPARATION 1 Some stainless steel parts may have a plastic protective wrap which must be peeled off The interior of the refrigerated beverage center should be washed thoroughly with hot soapy water rinsed and wiped dry to remove film residue and any installation dust or debris before being used Solutions stronger than soap and water are rarely needed 2 All stainless steel parts should be wiped with hot soapy water If buildup occurs do not use steel wool abrasive cloths cleaners or powders If it is necessary to scrape stainless steel to remove encrusted materials soak with hot wet cloths to loosen the material then use a wood or nylon scraper Do not
7. USE INSTALLATION INSTRUCTIONS 15 W UNDERCOUNTER FREESTANDING REFRIGERATED BEVERAGE CENTER Retain for Future Reference IMPORTANT PLEASE READ AND FOLLOW e Before beginning please read these instructions completely and carefully Do not remove permanently affixed labels warnings or plates from the product This may void the warranty Please observe all local end E codes and ordinances Please ensure that this product is properly grounded The installer should leave these instructions with the consumer who should retain for local inspector s use and for future reference WARNING To reduce the risk of fire electrical shock or injury when using your refrigerated beverage center follow basic precautions including the following eFOR YOUR SAFETYe DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE THE FUMES CAN CREATE A FIRE HAZARD OR EXPLOSION It is your responsibility to be sure your refrigerated beverage center is elocated so the front is not blocked to restrict incoming or discharge air flow eproperly leveled elocated in a well ventilated area econnected to the proper kind of outlet with the correct electric supply and grounding A 115 volt 60 Hz 15 amp fused electrical supply is required NOTE Time delay fuse or circuit breaker is recommended enot used by anyone unable to operate it properly eused only for its intended purpose properly maintai
8. an authorized Viking Range Corporation service agency or representative Warranty shall not apply to damage resulting from indoor units being used in outdoor situations This warranty does not apply to commercial usage Warrantor is not responsible for consequential or incidental damage whether arising out of breach of warranty breach of contract or otherwise Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you Owner shall be responsible for proper installation providing normal care and maintenance providing proof of purchase upon request and making the appliance reasonably accessible for service If the product or one of its component parts contains a defect or malfunction during the warranty period after a reasonable number of attempts by the warrantor to remedy the defects or malfunctions the owner is entitled to either a refund or replacement of the product or its component part or parts Replacement of a component part includes its free installation Warrantor s liability on any claim of any kind with respect to the goods or services covered hereunder shall in no case exceed the price of the goods or service or part there of which gives rise to the claim WARRANTY SERVICE Under the terms of this warranty service must be performed by a factory authorized Viking Range Corporation service agent or representative Service will be provided du
9. anding undercounter refrigerated beverage centers and all of their components and accessories except as detailed below are warranted to be free from defects in material or workmanship under normal household use for a period of two 2 years from the date of original retail purchase Viking Range Corporation warrantor agrees to repair or replace at its option any part which fails or is found to be defective during the warranty period Painted and decorative items are warranted to be free from defective materials or workmanship for a period of ninety 90 days from the date of original retail purchase ANY DEFECTS MUST BE REPORTED TO THE SELLING DEALER WITHIN NINETY 90 DAYS FROM DATE OF ORIGINAL RETAIL PURCHASE SIX YEAR FULL WARRANTY Any sealed refrigeration system component as listed below is warranted to be free from defective materials or workmanship in normal household use during the third through the sixth year from the date of original retail purchase Viking Range Corporation warrantor agrees to repair or replace at its option any part which fails or is found to be defective during the warranty period Sealed Refrigeration System Components Compressor Evaporator Condenser Connecting Tubing Dryer Strainer TWELVE YEAR LIMITED WARRANTY Any sealed refrigeration system component as listed above which fails due to defective materials or workmanship in normal household use during the seventh through the twelfth year from the date of
10. dental damage whether arising out of breach of warranty breach of contract or otherwise Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you Owner shall be responsible for proper installation providing normal care and maintenance providing proof of purchase upon request and making the appliance reasonably accessible for service If the product or one of its component parts contains a defect or malfunction during the warranty period after a reasonable number of attempts by the warrantor to remedy the defects or malfunctions the owner is entitled to either a refund or replacement of the product or its component part or parts Replacement of a component part includes its free installation Warrantor s liability on any claim of any kind with respect to the goods or services covered hereunder shall in no case exceed the price of the goods or service or part there of which gives rise to the claim WARRANTY SERVICE Under the terms of this warranty service must be performed by a factory authorized Viking Range Corporation service agent or representative Service will be provided during normal business hours and labor performed at overtime or premium rates shall not be covered by this warranty To obtain warranty service contact the dealer from whom the product was purchased an authorized Viking Range Corporation service agent or Viking Range Corp
11. e right side up position for at least 24 hours before plugging the unit in 1 Tip unit backwards so there is 1 foot of clearance on front of the unit Have someone to assist you in tilting the unit to prevent it from falling on you while installing the leg levelers Screw front two leg levelers into the screw impressions Leg levelers shoudl be screwed in until snug Repeat steps 1 amp 2 with the exception of tipping the unit forwards now to screw in the back two leg levelers Your leg levelers are now installed The unit should be level from front to back and side to side If floor conditions do not allow the unit to sit level adjust leg leveler s by turning the required leg leveler s counter clockwise to increase their height and clockwise to reduce their height 1 B W PO Screw Impressions Q O ELECTRICAL CONNECTION WARN l N G Electrical Shock Hazard Failure to follow these instructions could result in fire or electrical shock Electrical Requirements A 115 volt 60 Hz AC only 15 amp fused electrical supply is required A time delay fuse or circuit breaker is recommended It is recommended that a separate circuit serving only this appliance be provided Power Supply Grounding type wall with 3 prong Dr grounding plug eELECTRICAL GROUND IS REQUIRED ON THIS APPLIANCE eDO NOT UNDER ANY CIRCUMSTANCES REMOVE THE POWER SUPPLY CORD GROUND PLUG eDO NOT USE AN EXTENSION CORD
12. he shelves The wine section area of the refrigerated beverage center will be warmer than any other section To start your refrigerated beverage center use a screwdriver to turn the control clockwise to the middle thermostat setting Once the refrigerated beverage center is loaded allow at least 48 hours for the unit to stabilize before making any adjustments to the initial setting FOR OUTDOOR UNITS it is recommended that in temperatures above 110 F 43 3 C and below 40 F 4 4 C the unit be shut off The normal operating range for the unit is between 60 F 15 6 C and 100 F 37 8 C General Tips and Suggestions eAfter making a temperture adjustment allow 24 hours for your refrigerated beverage center to reach a new temperature setting eThe motor will start and stop often It must do this to maintain the temperature setting eUnplug the refrigerated beverage center before working on anything with the electrical system eExercise caution when sweeping vacuuming or mopping near the front of the unit Damage to the grill and or the light fixture switch can occur INTERIOR LIGHT The interior light allows you to view your refrigerated beverage center contents When the switch is in the OFF position the light will come on only when the door is opened In the ON position the light remains on continuously NOTE Outdoor units do not have a light switch LIGHT ASSEMBLY REPLACEMENT WARN i N G Failure to disconnect the p
13. ing wines CLEANING AND MAINTENANCE Any piece of equipment works better and lasts longer when maintained properly and kept clean Condenser The condenser tubing inside the cabinet does not require frequent cleaning however satisfactory cooling depends on adequate ventilation over the coils Be sure that nothing obstructs the required air flow openings in front of the cabinet Spiders and insects can nest in and around the refrigerated beverage center causing damage to the unit Frequently brush or vacuum lint and dirt from the condenser coils for efficient performance by unscrewing the grill on the bottom front of cabinet Cabinet The cabinet can be washed with mild soap and water and thoroughly rinsed with clear water Never use abrasive scouring powders Interior Wash interior compartment with mild soap and water Do not use abrasive powder solvent polish cleaner or undiluted detergent Stainless Steel Parts All stainless steel parts should be wiped regularly with hot soapy water Use a liquid cleaner designed for stainless steel when soapy water will not do the job Do not use steel wool abrasive cloths cleansers or powders Do not permit citrus or tomato juice to remain on stainless steel surfaces as citric acid will permanently discolor stainless steel Brass Parts CAUTION All brass parts have an epoxy coating DO NOT USE BRASS OR ABRASIVE CLEANERS ON THE BRASS PARTS All brass parts should be wiped regularly with hot soapy
14. it and when the wood is positioned on door Mounting surface Min 5 8 1 7 cm Non face side Max 3 4 1 9 cm 14 15 16 36 4 cm 7 5 32 18 2 cm 15 2 1 2 cm 23 32 1 8 cm TYP 7 13 16 19 8 cm TYP 1 23 32 4 4 cm min width to cover door 15 5 32 extrusion P 38 5 cm TYP 274 57 2 cm TYP 30 5 16 77 0 cm Pre drilled piolt holes 8 places ee E o 2 eee eee eee ee eee Mounting surface non face side Mounting surface non face side 1 4 X 3 8 Deep hinge screw clearance hole Locate and drill using door hinge hole after the door has been aligned to the unit and when the wood is positioned on door Attaching the Wood Frame to the Door DFUR Models 1 If the door is attached to the unit remove by unscrewing the top allen head set screw at the top hinge Remove the door by angling the door off of the bottom hinge pin 2 Peel back the door gasket to expose the screw holes 3 Set the wood frame flush to the front of the door in the desired location Clamp the wood frame to the door if necessary Insert the wood screws through the back of the door into the pilot holes in the wood frame and tighten Reinstall the door gasket by pressing into the door channel Make certain the corners are inserted fully Install the door to the unit Use the supplied plastic washer as shown in the figure below Realigning the door may be necessary Any fi
15. many door openings prolonged door openings hot humid weather increases condensation Moisture collects to outside surface Control improperly set Hot humid weather increases condensation Interior too hot too cold Control improperly set faulty thermometer relocate thermometer to center of cabinet and recheck SERVICE INFORMATION It is assumed that your refrigerated beverage center has been properly installed in accordance with all specifications and local codes and the appliance has been properly grounded If your refrigerated beverage center should fail to operate review the troubleshooting chart before calling for service If service is required 1 Call your dealer or authorized service agency The name of the authorized service agency can be obtained from the dealer or distributor in your area 2 Have the following information readily available Model number eSerial number eDate of purchase eName of dealer from whom purchased If you are unable to obtain the name of an authorized service agency or if you continue to have service problems contact Viking Range Corporation at 888 845 4641 or write to VIKING PREFERRED SERVICE 111 Front Street Greenwood Mississippi 38930 USA Record the following information indicated below You will need it if service is ever required The serial number and model number for your refrigerator is located on the front of the unit at the base of the door frame Model Number ___
16. nal door adjustments can be made using a 1 8 allen head driver to adjust the door s hinges See figure below 8 Attach the door light striker plate as shown using the 5 16 hex or phillips head screws provided Make certain the light is able to turn on and off when the door is opened and closed 9 Attach the door to the unit by reversing step number 1 above Ea Hinge Hardware Installation Details CAUTION CAUTION 2 Nylon Door can become Door can become Cabinet hardware Magnetic door gasket disengaged if washers disengaged if Hinge components at 3 8 clearance holes are not installed i washers are not top hinge for frame wood screws installed 8 holes se 5 8 x 7 32 ID washer a ee a l Shoulder f bushing Wood I I I Frame i 1 Door Hinge Door Hinge S Shoulder bushing meg 3 4 OD x 7 16 ID Washer NEE 34 OD x 1 4 ID CAUTION Washer Door may not swing properly 3 Nylon hardware if all nylon components are components at Wood Frame not installed as shown bottom hinge Bottom Hinge Cover Top Hinge Cover 1 8 allen head screws for hinge Door hinge adjustment adjustment screws Door light striker plate Attached wood frame LEG LEVELER INSTALLATION READ BEFORE INSTALLING LEG LEVELERS WARNING Do not lay unit on top side back or front If unit is accidentally laid in any position other than right side up then the unit must remain in th
17. ned eSAVE THESE INSTRUCTIONS PROPER DISPOSAL OF YOUR OLD REFRIGERATION PRODUCT A DANGER IMPORTANT Child entrapment and suffocation are not problems of the past Junked or Suffocation Hazard abandoned refrigerated beverage centers are still Remove doors from your old dangerous even if they will sit for just a few refrigerated beverage center days If you are getting rid of your refrigerated Failure to do so can result in beverage center please follow the instructions child entrapment which can below to help prevent accidents cause death or brain damage BEFORE YOU THROW AWAY YOUR OLD REFRIGERATED BEVERAGE CENTER eTake off the doors eLeave the shelves in place so that children may not easily climb inside 41009335 Rev B UNDERCOUNTER CABINET CUTOUT 15 96 1 cm Min 34 1 2 87 6 cm Max 35 1 8 89 2 cm C Min 24 61 0 cm 15 38 1 cm width for cabinet only If door is recessed between cabinets cabinet cutout must be 15 1 4 38 7 cm SPECIFICATIONS DIMENSIONS PROFESSIONAL SERIES Basic Electric Data e115 VAC 60 Hz eMaximum amps 3 0 eApproximate Shipping Weight 110 Ibs 49 5 kg Side View 7 lt 21 3 16 53 8 cm gt w 23 5 8 60 0 cm 26 1 8 66 4 cm Front View Min 34 1 4 87 0 cm to Max 35 88 9 cm with leveling legs fully extended 30 3 4 78 1 cm e 14 3 4 37 5 cm
18. oration Provide model and serial number and date of original purchase For the name of your nearest authorized Viking Range Corporation service agency call the dealer from whom the product was purchased or Viking Range Corporation IMPORTANT Retain proof of original purchase to establish warranty period The return of the Owner Registration Card is not a condition of warranty coverage You however should return the Owner Registration Card so that Viking Range Corporation can contact you should any question of safety arise which could affect you Any implied warranties of merchantability and fitness applicable to the above described undercounter refrigerator are limited in duration to the period of coverage of the applicable express written limited warranties set forth above Some jurisdictions do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you This warranty gives you specific rights and you may also have other rights which may vary from jurisdiction to jurisdiction Viking Range Corporation 111 Front Street e Greenwood Mississippi USA 38930 662 455 1200 www vikingrange com UL c UL F20343B 062007J Specifications subject to change without notice
19. ower cord when changing the light assembly may result in A electrical shock NOTE Please contact your Viking Range Corporation distrib deal q ligh bl reen i parts alstrioutor or dealer to order new light assembly ground wire assembly To replace the light first disconnect the refrigerated Wax Head ant beverage center s power cord Next remove both een the green ground wire screw located on the left of the light assembly and the other screw located on the right of the light assembly with a 5 16 hex head rg i f gt Hex head screwdriver See drawing Unplug the light unit and u screw remove complete light assembly To install the new light assembly screw in the green AWM GY ground wire screw and the screw located on the right onee ae with a 5 16 hex head screwdriver and plug the light unit in WIRE SHELVES The adjustable wire shelves can be removed by lifting up on the shelf slightly and sliding it out To reinsert shelves position the shelf over the track and slide into place The shelves are tapered at the back to allow easy installation The wine rack will hold 5 bottles of wine The necks of the bottles alternate front rear facing to back front facing The rack holds three bottles facing to the rear and two bottles facing to the front Glass shelf separating beverage section from wine section Rear NOTE The glass shelf separates temperature zone Do not remove when stor
20. repair or replace at its option any part which fails or is found to be defective during the warranty period Sealed Refrigeration System Components Compressor Evaporator Condenser Connecting Tubing Dryer Strainer It is recommended that in temperatures above 100 F 37 8 C and below 40 F 4 4 C the unit be shut off The normal operating range for the unit is between 60 F 15 6 F and 100 F 377 C NINETY 90 DAY RESIDENTIAL PLUS WARRANTY This warranty applies to applications where use of the product extends beyond normal residential use Examples are but not limited to bed and breakfasts fire stations private clubs churches etc This warranty excludes all commercial locations such as restaurants food service locations and institutional food service locations This warranty extends to the original purchaser of the product warranted hereunder and to each transferee owner of the product during the term of the warranty This warranty shall apply to products purchased and located in the United States and Canada Products must be purchased in the country where service is requested Warranty labor shall be performed by an authorized Viking Range Corporation service agency or representative Warranty shall not apply to damage resulting from abuse accident natural disaster loss of electrical power to the product for any reason alteration improper installation improper operation or repair or service to the product by anyone other than
21. ring normal business hours and labor performed at overtime or premium rates shall not be covered by this warranty To obtain warranty service contact the dealer from whom the product was purchased an authorized Viking Range Corporation service agent or Viking Range Corporation Provide model and serial number and date of original purchase For the name of your nearest authorized Viking Range Corporation service agency call the dealer from whom the product was purchased or Viking Range Corporation IMPORTANT Retain proof of original purchase to establish warranty period The return of the Owner Registration Card is not a condition of warranty coverage You however should return the Owner Registration Card so that Viking Range Corporation can contact you should any question of safety arise which could affect you Any implied warranties of merchantability and fitness applicable to the above described undercounter refrigerated beverage center are limited in duration to the period of coverage of the applicable express written limited warranties set forth above Some jurisdictions do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you This warranty gives you specific rights and you may also have other rights which may vary from jurisdiction to jurisdiction 14 UNDERCOUNTER FREESTANDING REFRIGERATED BEVERAGE CENTER WARRANTY Units certified for Indoor Use TWO YEAR FULL WARRANTY Built in freest
22. rt Softwood 5 64 0 20 cm Assembling Door Hinge Brackets Disregard if hinge brackets are already attached 1 Attach the top and bottom door hinge brackets to the door with the 10 32 machine screws and a 1 8 allen head driver as shown in Figure 1 below 2 Press in the shoulder bushings to the top and bottom door hinge brackets Make certain that the shoulder is to the outside of the door as shown in Figure 1 below 3 Test fit the door to the unit to make certain door will hang correctly The door is hung correctly when the top of the door is parallel to the top of the unit See Figure 2 Adjustments can be made by loosening the door hinge machine screws and moving the door hinge brackets on the door 4 Tighten all four 4 machine screws after adjustments have been made 5 Remove the door from the unit by removing the units top hinge set screw and angling the door off of the bottom hinge pin Figure 2 Figure 1 This surface parallel to the unit Shoulder Bushing Right hinge door shown Door Hinge Bracket 10 32 Machine Screw Door Hinge EAA Screw Holes hs 0 Door Front y Surface Ui ZG S igi Alh Typical Top and Bottom Door Hinge Bracket Assembly Selecting and Preparing the Wood Frame DFUR Model FOR A 3 1 2 TOE KICK COVERS THE ENTIRE DOOR EXTRUSION 1 4 X 3 8 Deep hinge screw clearance hole Locate and drill using door hinge hole after the door has been aligned to the un
23. use a metal knife spatula or any other metal tool to scrape stainless steel scratches are almost impossible to remove WIRING DIAGRAM UNDERCOUNTER 15 W REFRIGERATED BEVERAGE CENTER BLACK SMOOTH HOT tal BLACK RIBBED NEUTRAL wore SLEEVE NONPOLARIZED BLACK NONPOLARIZED air eas WARNING ELECTRICAL GROUNDING INSTRUCTIONS This appliance is equipped with a three prong grounding plug for your protection against shock hazard and should be plugged sue pid CONPRESSOR mew directly into a properly grounded n three prong receptacle Do not Back 4 BLUE cut or remove the grounding A prong from this plug POTENTIOMETER THERMISTOR GREY LIGHT SWITCH LIGHT OPTIONAL FEATURE OPERATING INSTRUCTIONS Setting the Controls The total available temperature range of the indoor unit is from 39 42 F 4 0 5 6 C to 54 56 F 12 13 C The total available temperature range of the outdoor unit is from 33 35 F 0 5 1 1 C to 54 56 F 12 13 C The higher the number selected the cooler the temperature within the unit As with any refrigerated beverage center there is a slight temperature variance at different locations within the cabinet For example the coolest area will be in the rear of the shelf above the glass shelf The area on the top shelf will be 3 7 F warmer The area in the front will be 1 5 F warmer than the area in the rear of t
24. water When hot soapy water will not do the job use every day household cleaners that are not abrasive Glass Door Indoor Units only Use a glass cleaner or mild soap and water with soft cloth to clean the glass door Do not use any abrasive powders On full overlay models use caution when cleaning near logo area Door Gasket The vinyl gasket may be cleaned with mild soap and water a baking soda and water solution or a mild scouring powder Painted Surfaces Wash with warm soapy water DO NOT USE steel wool abrasive cleansers ammonia acids or commercial oven cleaners which may damage the finish 12 ENERGY SAVING TIPS eReduce door openings Close the door as soon as you can eKeep the condenser coils on bottom of the unit clean See Cleaning and Maintenance eAdjust the temperature control to a warmer setting when practical Do not put hot foods in the refrigerated beverage center e nstall unit away from the stove or other heat sources TROUBLESHOOTING CHART Problem Possible Cause Solution Odor in cabinet Interior needs cleaning Noisy operation cabinet vibrates Cabinet not level weak floor Cabinet light not working Bulb burned out no power at outlet Appliance will not run Temperature control to OFF line cord not plugged in no power at electrical outlet house fuse blown Appliance runs too long Prolonged door openings control set too cold condenser needs cleaning Moisture collects inside Too
Download Pdf Manuals
Related Search