ViewSonic PJ551D-2 User's Manual
Contents
1. Wear protective gloves and eyeglasses when fixing or detaching the lamp Faster on off cycles will damage the lamp and reduce lamp life Wait at least for 5 minutes to turn off the projector after powering on Do not operate the lamp in proximity to paper cloth or other combustible material nor cover it with such materials Otherwise it could cause a fire Do not operate the lamp in an atmosphere containing an inflammable substance such as thinner Otherwise it could cause a fire or explosion Thoroughly ventilate the area or the room when operating the lamp in an oxygen atmosphere in the air If ozone is inhaled it could cause headaches nausea dizziness etc The inorganic mercury is involved in the lamp If the lamp bursts the mercury inside the lamp will go out of the projector Leave the area immediately if the lamp shatters while being operated and ventilate the area for at least 30 minutes in order to avoid the inhalation of mercury fumes Otherwise it could be harmful to user s health ViewSonic 19 PJ551D Turn off the projector If the projector is installed in a ceiling mount remove it from the mount Unplug the power cord Loosen the screw in the side of the lamp cover and remove the cover Remove the screws from the lamp module raise the handle and lift out the module Insert the new lamp module into the projector and tighten the screws Replace the lamp cover and tighten the screw 8 Turn on the2. Front IR remote control sensor 0000 90 Ventilation holes ViewSonic 8060090 AC power socket Control panel Zoom ring Focus ring Lamp cover PJ551D Rear View Connection ports Kensington lock Rear IR remote control sensor Ventilation holes ococc Bottom View Q Elevator foot e Ceiling mount e Tilt adjustment foot Wi This projector can be used with a ceiling mount for support The ceiling mount is not included in the package ViewSonic 4 PJ551D Using the Product Control Panel LED Lamp Lamp LED indicator Refer to LED Indicator Messages Temp Temperature LED indicator Refer to LED Indicator Messages Button Function 0 o o 8 Four directional buttons Use four directional buttons to select items or make adjustments to your selection Enter Enter to sub menu and confirm the menu selection Activate in Color Setting Lamp Counter Reset and Factory Default menu operations Resync Resynchronize the projector to the input signal from a computer b Power Turn the projector on or off Menu Display or exit the on screen display menus Source Manually select an input source ViewSonic 5 PJ551D Connection Ports Computer Out Computer In S Video Video SERVICE Computer Out PJ551D 2 Connect to a computer display etc Computer
3. LED Indicator Messages LED Type LAMP LED TEMP LED LAMP LED TEMP LED LAMP LED TEMP LED LAMP LED TEMP LED LAMP LED TEMP LED LAMP LED TEMP LED LAMP LED TEMP LED ViewSonic Color Green Off Green Green Green Green Amber Green Amber Amber Green Red Amber Off Status Flash Solid Flash Solid Solid Solid Solid Solid Solid Solid Flash Solid Meaning The projector is in standby mode The projector system has some problems with its fan so the projector cannot start up The lamp is in good condition and is projecting at maximum brightness The lamp has reached its end of life and must be changed soon The lamp will continue to operate until it fails Change the lamp If the lamp is off then the ballast will become malfunction The projector is shutting and the fan motor is cooling the lamp for shutdown Do not unplug the power cord or turn the power off before the Lamp LED changes to flashing The fan motor will turn off when the lamp has cooled Temperature is too high The lamp will turn off The fan motor is cooling the lamp The lamp ignition failed If temperature is too high the fans will cool the lamp 22 PJ551D Compatibility Modes Computer Compatibility Resolution H Sync KHz V Sync Hz VGA 640 x 480 31 5 59 9 37 9 72 8 37 5 75 0 43 3 85 0 SVGA 800 x 600 35 2 56 3 37 9 60 3 48 1 72 2 46 9 75 0 53 7 85 1 XGA 1024 x 768 48 4 60 0 5
4. Signal Type Specify the source to the Computer In terminal that you wish to project E YPbPr For component 480p 576p 720p 1080i signals W RGB ForVGA signal W YCbCr For component 480i 576i signals Lamp Counter Display the lamp s elapsed operating time in hours Lamp Counter Reset Reset the lamp counter to O hours Power Saving If no operation is performed for a specific period of time the power to the projector is automatically turned off Auto Source Automatically scan the input source ViewSonic 16 PJ551D ECO Mode Use this function to dim the projector lamp light output which will lower power consumption and increase lamp life High Altitude Turning on High Altitude mode operates the fans at full speed continuously to allow for proper high altitude cooling of the projector Filter Mode When an optional air filter is attached be sure to turn on the Filter Mode otherwise the machine can overheat and shutdown automatically OSD Timeout Duration OSD menu stays active at idle state by second Option Computer Video Mode Blank Screen Blank the screen temporarily and select the screen color when this function is active Start up Screen Select start up screen when the projector is powered on or when no signal is input User is the screen that you captured Screen Capture Capture the current projection screen as a start up screen Password Set or change the password When the password function
5. 00 47 3522074 3 52 20 09 E Mail compumantenimientos prodigy net mx Veracruz Ver CONEXION Y DESARROLLO S A DE C V Av Americas 419 ENTRE PINZ N Y ALVARADO Fracc Reforma C P 91919 Tel 01 22 91 00 31 67 E Mail gacosta qplus com mx Cuernavaca Compusupport de Cuernavaca SA de CV Francisco Leyva 178 Col Miguel Hidalgo C P 62040 Cuernavaca Morelos Tel 01 777 3180579 01 777 3124014 E Mail aquevedo compusupporteva com Guadalajara Jal SERVICRECE S A de C V Av Ni os H roes 2281 Col Arcos Sur Sector Ju rez 44170 Guadalajara Jalisco Tel 01 52 33 36 15 15 43 E Mail mmiranda servicrece com Monterrey Global Product Services Mar Caribe 1987 Esquina con Golfo P rsico Fracc Bernardo Reyes CP 64280 Monterrey N L M xico Tel 8129 5103 E Mail aydeem gps1 com mx Oaxaca Oax CENTRO DE DISTRIBUCION Y SERVICIO S A de C V Murgu a 708 P A Col Centro 68000 Oaxaca Tel 01 52 95 15 15 22 22 Fax 01 52 95 15 13 67 00 E Mail gpotai2001 hotmail com FOR USA SUPPORT ViewSonic Corporation 381 Brea Canyon Road Walnut CA 91789 USA Tel 800 688 6688 English 866 323 8056 Spanish Fax 1 800 685 7276 E Mail http www viewsonic com PRJ LWO03 Rev 1A 06 25 07 PJ551D d ViewSonic
6. 9999 service in viewsonic com Korea www kr viewsonic com T 080 265 9080 service kr viewsonic com Latin America Argentina www viewsonic com la T 0800 666 0098 F 1 909 444 5655 soporte viewsonic com Latin America Brazil www viewsonic com la T 0800 891 1829 F 1 909 444 5655 soporte viewsonic com Latin America Chile www viewsonic com la T 800 440303 F 1 909 444 5655 soporte viewsonic com Latin America Columbia www viewsonic com la T 01800 9 156588 F 1 909 444 5655 soporte viewsonic com Latin America Mexico www viewsonic com la T 001 866 823 2004 F 1 909 444 5655 soporte viewsonic com Renta y Datos 29 SUR 721 COL LA PAZ 72160 PUEBLA PUE Tel 01 222 891 55 77 CON 10 LINEAS Electroser Av Reforma No 403Gx39 y 41 97000 Merida Yucatan Tel 01 999 925 19 16 Other places please refer to http www viewsonic com la soporte index htm Mexico Latin America Peru www viewsonic com la T 0800 53311 F 1 909 444 5655 soporte viewsonic com Macau www hk viewsonic com T 853 700 303 service hk viewsonic com Puerto Rico amp Virgin Islands www viewsonic com T 1 800 688 6688 English T 1 866 379 1304 Spanish F 1 909 468 1202 service us viewsonic com soporte viewsonic com Singapore Malaysia Thailand www ap viewsonic com T 65 6461 6044 service sg viewsonic com South
7. In Connect image input signal analog RGB or component to this jack S Video Connect S Video output from video equipment to this jack Video Connect composite video output from video equipment to this jack SERVICE This connector is for firmware update o o 8 86 ViewSonic 6 PJ551D Remote Control 0 e Power Turn the projector on or off Four directional buttons Use four directional buttons to select items or make adjustments to your selection Menu Display or exit the on screen display menus Enter Confirm the selection Keystone A v Adjust image distortion caused by tilting the projector Page A Page Y Computer mode only This button has same function as Page Up Page Down button in a PC keyboard This function is only available when the projector is connected to a computer via a USB cable Source Manually selects an input source Freeze Press Freeze to pause the Screen image Press again to cancel the Freeze function Blank Cut off the screen temporarily Press again to cancel the Blank function ViewMatch Switch the white intensity between 3 and 10 Auto Automatically adjust frequency and phase This function is available for computer mode only ViewSonic 90000008 ViewSonic PJ551D 90088 For the first time use Remove the transparent insulation tape by pulling it before use Battery holder For battery change 1 Push the catch t
8. is added image projection requires an entry of the preset password at power on DCR Dynamic Contrast Ratio Enable DCR will further enhance contrast ratio by darkening the black scenes Disable DCR will resume to normal contrast performance DCR will impact lamp life and system noise performance Language Computer Video Mode Select the language used by the on screen menu Factory Default Computer Video Mode Restore all menu settings to factory default settings ViewSonic 17 PJ551D Maintenance The projector needs proper maintenance You should keep the lens clean as dust dirt or spots will project on the screen and diminish image quality If any other parts need replacing contact your dealer or qualified service personnel When cleaning any part of the projector always switch off and unplug the projector first Warning Never open any of the covers on the projector Dangerous electrical voltages inside the projector can cause severe injury Do not attempt to service this product yourself Refer all servicing to qualified service personnel Cleaning the Lens Gently wipe the lens with lens cleaning paper Do not touch the lens with your hands Cleaning the Projector Housing Gently wipe with a soft cloth If dirt and stains are not easily removed use a soft cloth damped with water or water and neutral detergent and wipe dry with a soft dry cloth v Turn off the projector and remove the AC power cord from the
9. not cover 1 Any product on which the serial number has been defaced modified or removed 2 Damage deterioration or malfunction resulting from a Accident misuse neglect fire water lightning or other acts of nature unauthorized product modification unauthorized attempted repair or failure to follow instructions supplied with the product Any damage of the product due to shipment Causes external to the product such as electrical power fluctuations or failure Use of supplies or parts not meeting ViewSonic s specifications Normal wear and tear Any other cause which does not relate to a product defect 3 Any product exhibiting a condition commonly known as image burn in which results when a static image is displayed on the product for an extended period of time 4 Removal installation insurance and set up service charges How to get service For information about receiving service under warranty contact ViewSonic Customer Support Please refer to the attached Customer Support page You will need to provide your product s serial number so please record the product information in the space provided below on your purchase for your future use Please retain your receipt of proof of purchase to support your warranty claim For Your Records monos Product Name Model Number Document Number Serial Number Purchase Date Extended Warranty Purchase Y N If so what date does warranty exp
10. power outlet before beginning maintenance work Make sure the lens is cool before cleaning Do not use detergents or chemicals other than those noted above Do not use benzene or thinners Do not use chemical sprays Use a soft cloth or lens paper only ViewSonic 18 PJ551D Replacing the Lamp As the projector operates over time the brightness of the projector lamp gradually decreases and the lamp becomes more susceptible to breakage We recommend replacing the lamp if a warning message is displayed Do not attempt to replace the lamp yourself Contact the qualified service personnel for replacement Wi The lamp becomes high temperature after turning off the projector with the power button If you touch the lamp you may scald your finger When you replace the lamp wait for at least 45 minutes for the lamp to cool down W Do not touch the lamp glass at any time The lamp may explode due to improper handling including the touching of the lamp glass W Lamp lifetime may differ from lamp to lamp and according to the environment of use There is no guarantee of the same lifetime for each lamp Some lamps may fail or terminate their lifetime in a shorter period of time than other similar lamps A lamp may explode as a result of vibration shock or degradation as a result of hours of use as its lifetime draws to an end Risk of explosion may differ according to the environment or conditions in which the projector and lamp are being used
11. 10 Gamma ii jl n Computer Image Frequency 50 50 Tracking 0 31 H Position 10 10 V Position 10 10 Video Image Color mm Sharpness 0 31 Tint 100 Setting Menu Position Projection pee YPbPr RGB YCbCr Lane conor Tar cour Rese crees CL EE Auto Source Yes No cpm OSD Timeout 5 15 30 45 60 Sec Blank S Black Blue Gray Red Green m ank Screen Yellow Cyan Magenta White Start up Screen ViewSonic User Screen Capture Input Password zT password Change Password Exit ASE Italiano Francais Option Espa ol Portugu s Pycckm AHX etz0l ViewSonic 14 PJ551D How to operate 1 Press the Menu button to open the OSD menu 2 When OSD is displayed use A v to select any feature in the main menu 3 After selecting the desired main menu feature press to enter sub menu for feature setting 4 Adjust the settings with lt gt Press the Menu button the screen will return to the main menu 6 To exit OSD Press the Menu button again The OSD menu will close and the projector will automatically save the new settings e Picture Computer Video Mode Brightness Brighten or darken the image Contrast Set the difference between light and dark areas Color Setting Adjust the color temperature At higher temperature the screen looks colder at lower temperature the screen looks warmer If you select User Red Green and Blue cab be adjusted K
12. 10 Connecting the Projector 10 Powering On Off the Projector 11 Adjusting the Projector enne nnne nnne enne 12 Menu Operations cia 14 MEAR 18 Cleaning the Lens isa 18 Cleaning the Projector Housing seeeeenemnne 18 Replacing the Lamp ore ai 19 Specifications oo ccisisbencescaseczececezedesacebede castvacbcdeveeesusndedes ees 21 Appendix reinen etecce t nece reete zer den ess 22 LED Indicator Messages eerie eren e na cer ra rh eere EE eere ed unen 22 Compatibility Modes 23 Troubleshooting sinisa ence petra to nete rente er europa ne epe ch pe DRE A e RES 24 Other Information esses 25 Customer SUppott 2 e ea aa a eg dn re eaa aeo one eaae erede EE a danta 25 Limited Warranty Mexico Limited Warranty rrr rtr ee e n bb tes 28 ViewSonic PJ551D Introduction Projector Features The projector integrates high performance optical engine projection and a user friendly design to deliver high reliability and ease of use The projector offers the following features Single chip 0 55 Texas Instruments DLP technology XGA 1024 x 768 pixels Auto image re sizing Auto Sync to 1024 x 768 full screen with scaling compression compatibility for VGA SVGA XGA and SXGA Compatibility with Macintosh computers Compatibility with NTSC PAL SECAM and HDTV D Sub 15 pin terminal for analog video connectivity User friendly multi language on scre
13. 6 5 70 1 60 0 75 0 68 7 85 0 SXGA 1152 x 864 64 0 70 0 67 5 75 0 1280 x 960 60 0 60 0 75 0 75 0 1280 x 1024 64 0 60 0 WXGA 1280 x 768 47 8 60 0 60 3 74 9 68 6 84 8 1280 x 800 49 7 59 8 62 8 74 9 Video Signal Horizontal Frequency kHz Vertical Frequency Hz 480i 15 8 kHz 60 Hz 480p 31 5 kHz 60 Hz 576i 15 6 kHz 50 Hz 576p 31 3 kHz 50 Hz 720p 45 0 kHz 60 Hz 720p 37 5 kHz 50 Hz 1080i 33 8 kHz 60 Hz 1080i 28 1 kHz 50 Hz ViewSonic 23 PJ551D Troubleshooting Refer to the symptoms and measures listed below before sending the projector forrepairs If the problem persists contact your local reseller or service center Please refer to Indicator Messages as well Start up problems If no lights turn on W Be sure thatthe power cord is securely connected to the projector and the other end is plugged into an outlet with power W Press the power button again W Unplug the power cord and wait for a short while then plug it in and press the power button again Image problems If the searching source is displayed Wi Pressthe Source button one or more times to select another active input source NW Be sure the external source is turned on and connected W Fora computer connection ensure your notebook computer s external video port is turned on Refer to the computer manual If the image is out of focus Wi Be sure the lens cover is open E While displaying the on screen menu adjust the focus ring The image size should n
14. Africa www viewsoniceurope com www viewsoniceurope com uk Support Calldesk htm United Kingdom www viewsoniceurope com uk www viewsoniceurope com uk Support Calldesk htm United States www viewsonic com T 1 800 688 6688 F 1 909 468 1202 service us viewsonic com ViewSonic PJ551D Limited Warranty VIEWSONIC PROJECTOR What the warranty covers ViewSonic warrants its products to be free from defects in material and workmanship under normal use during the warranty period If a product proves to be defective in material or workmanship during the warranty period ViewSonic will at its sole option repair or replace the product with a like product Replacement product or parts may include remanufactured or refurbished parts or components How long the warranty is effective North and South America 3 years for all parts excluding the lamp 3 years for labor 1 year for the original lamp from the date of the first consumer purchase Europe 3 years for all parts excluding the lamp 3 years for labor 1 year for the original lamp from the date of the first consumer purchase Other regions or countries Please check with your local dealer or local ViewSonic office for the warranty information Lamp warranty subject to terms and conditions verification and approval Applies to manufacturer s installed lamp only All accessory lamps purchased separately are warranted for 90 days Who the warran
15. ViewSonic PJ551D PJ551D 2 User Guide DLP Projector Guide de Putilisateur Bedienungsanleitung ACME T RENE TO Ac EN MO Guia do usu rio Anv ndarhandbok Kayttoopas PyKOBOACTBO nonb3oBaTenA EAF 83 EPA 15112 AH XL erul Al IMPORTANT Please read this User Guide to obtain important information on installing and using your product in a safe manner as well as registering your product for future service Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation which is also found on our web site at http www viewsonic com in English or in specific languages using the Regional selection box in the upper right corner of our website ViewSonic Model No VS11973 Compliance Information FCC Statement This device complies with part 15 of FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and
16. e D Sub to D Sub S Video Cable e USB Cable Composite Video Cable e VGA D Sub to HDTV RCA Cable fe E eae Desktop type 5 OL an Cs Video Source example entm output equipment such as DVD player or Settop Box high definition TV source E B E JO When connecting cable power cords of both a projector and external equipment should be disconnected from AC outlet Wi The figure above is a sample connection This does not mean that all of these devices can or must be connected simultaneously The cables that come with the projector may differ from the above illustration The included cables are based on actual shipment delivery ViewSonic 10 PJ551D Powering On Off the Projector Powering On the Projector 1i Remove the projector lens cap 2 Complete the AC power cord and peripheral signal cable s connections 3 Press b button to turn on the projector The projector takes a minute or so to warm up 4 Turn on your source computer notebook DVD etc The projector automatically detects your source W If you are connecting multiple sources to the projector simultaneously press the Source button Warning W Remove the lens cap first before powering on W Never lo
17. e on ViewSonic products sold outside of the U S A and Canada contact ViewSonic or your local ViewSonic dealer The warranty period for this product in mainland China Hong Kong Macao and Taiwan Excluded is subject to the terms and conditions of the Maintenance Guarantee Card For users in Europe and Russia full details of warranty provided can be found in www viewsoniceurope com under Support Warranty Information 4 3 Projector Warranty PRJ LWO01 Rev 1h 06 25 07 ViewSonic 27 PJ551D Mexico Limited Warranty VIEWSONIC PROJECTOR What the warranty covers ViewSonic warrants its products to be free from defects in material and workmanship under normal use during the warranty period If a product proves to be defective in material or workmanship during the warranty period ViewSonic will at its sole option repair or replace the product with a like product Replacement product or parts may include remanufactured or refurbished parts or components amp accessories How long the warranty is effective 3 years for all parts excluding the lamp 3 years for labor 1 year for the original lamp from the date of the first consumer purchase Lamp warranty subject to terms and conditions verification and approval Applies to manufacturer s installed lamp only All accessory lamps purchased separately are warranted for 90 days Who the warranty protects This warranty is valid only for the first consumer purchaser What the warranty does
18. en display Advanced electronic keystone correction means compressed Notes on the AC Power Cord AC Power Cord must meet the requirement of countries where you use this projector Please confirm your AC plug type with the graphics below and ensure that the proper AC Power Cord is used If the supplied AC Power Cord does not match your AC outlet please contact your sales dealer This projector is equipped with a grounding type AC line plug Please ensure that your outlet fits the plug Do not defeat the safety purpose of this grounding type plug We highly recommend using a video source device also equipped with a grounding type AC line plug to prevent signal interference due to voltage fluctuations We ES sy For Australia and Mainland China For Continental Europe For the U K ViewSonic 1 PJ551D Package Contents When you unpack the projector make sure you have all these components Projector with Lens Cap AC Power Cord VGA Cable D SUB to D SUB Quick Start Guide Remote Control IR User s Manual Quick Start Guide if you ever to ship your unit For maximum protection repack your unit as it was originally packed at the factory Wi Save the original shipping carton and packing material they will comein handy Wi Accessories and components may vary by retailer and region ViewSonic 2 PJ551D Projector Overview Front View Lens cap Elevator button Lens cap strap Projection lens
19. eystone Correct the keystone distortion Aspect Ratio Select how the picture fits on the screen W 43 The input source will be scaled to fit the projection screen W 16 9 Theinput source will be scaled to fit the width of the screen Image Te are many factory presets optimized for various types of images W PC For computer or notebook W Movie For home theater E sRGB For PC standard color E User Memorize user s settings Screen Type Select the projection screen type White Intensity Increase the brightness of white areas Gamma Effect the represent of dark scenery With greater gamma value dark scenery will look brighter ViewSonic 15 PJ551D Computer Image Computer Mode Frequency Adjust the timing of the projector relative to the computer Tracking Adjust the phase of the projector relative to the computer H Position Horizontal Position Adjust the image left or right within the projection area V Position Vertical Position Adjust the image up or down within the projection area Video Image Video Mode Color Adjust the intensity of colors Sharpness Sharpen or soften the image Tint Shift colors toward red or green Setting Computer Video Mode Menu Position Choose the menu location on the display screen Projection Adjust the picture to match the orientation of the projector upright or upside down in front of or behind the screen Invert or reverse the image accordingly
20. ire 1 To obtain warranty service you will be required to provide a the original dated sales slip b your name c your address d a description of the problem and e the serial number of the product 2 Take or ship the product in the original container packaging to an authorized ViewSonic service center 3 Round trip transportation costs for in warranty products will be paid by ViewSonic Limitation of implied warranties There are no warranties express or implied which extend beyond the description contained herein including the implied warranty of merchantability and fitness for a particular purpose Exclusion of damages ViewSonic s liability is limited to the cost of repair or replacement of the product ViewSonic shall not be liable for 1 Damage to other property caused by any defects in the product damages based upon inconvenience loss of use of the product loss of time loss of profits loss of business opportunity loss of goodwill interference with business relationships or other commercial loss even if advised of the possibility of such damages 2 Any other damages whether incidental consequential or otherwise 3 Any claim against the customer by any other party 4 Repair or attempted repair by anyone not authorized by ViewSonic ViewSonic 28 PJ551D Contact Information for Sales amp Authorized Service Centro Autorizado de Servicio within Mexico Name address of manufacturer and importers M
21. ke or ship the product freight prepaid in the original container to an authorized ViewSonic service center or ViewSonic 4 For additional information or the name of the nearest ViewSonic service center contact ViewSonic ViewSonic 26 PJ551D Limitation of implied warranties There are no warranties express or implied which extend beyond the description contained herein including the implied warranty of merchantability and fitness for a particular purpose Exclusion of damages ViewSonic s liability is limited to the cost of repair or replacement of the product ViewSonic shall not be liable for 1 Damage to other property caused by any defects in the product damages based upon inconvenience loss of use of the product loss of time loss of profits loss of business opportunity loss of goodwill interference with business relationships or other commercial loss even if advised of the possibility of such damages 2 Any other damages whether incidental consequential or otherwise 3 Any claim against the customer by any other party Effect of state law This warranty gives you specific legal rights and you may also have other rights which vary from state to state Some states do not allow limitations on implied warranties and or do not allow the exclusion of incidental or consequential damages so the above limitations and exclusions may not apply to you Sales outside the U S A and Canada For warranty information and servic
22. ng the projector in its carrying case Adjusting the Projector Zoom and Focus Zoom ring Focus ring 1 Focus the image by rotating the focus ring A still image is recommended for focusing 2 Adjustthe image by sliding the zoom ring ViewSonic 12 PJ551D Adjusting Projection Image Size Refer to the graphic and table below to determine the screen size and projection distance 249 80 A 124 90 207883 gt sul 2 74 94 MS 49 96 113 92 Sen ce anf 6025 2 90 08 gt pp 45 57 EE 127 34 El hm Min 120m 3 0m 15 0m 110 0m Max Projection Distance Screen Size for 4 3 aspect ratio diagonal length meters Wide inches Tele inches 1 2 30 08 27 34 2 49 96 45 57 3 74 94 68 35 5 124 90 113 92 10 249 80 227 83 build up and damage to the projector Make sure the heat ventilation holes are not blocked Do not use the projector in a smoky environment Smoke residue may cause build up on critical parts i e DMD lens assembly etc for Wi Position the projector in a horizontal position other positions can cause heat ViewSonic 13 PJ551D Menu Operation The projector has multilingual on screen display menus that allow you to make image adjustments and change a variety of settings const 0 10 caer stre E Image PC Movie sRGB User Normal White Board Sereen Type Black Board Green Board White Intensity
23. o the right and remove the battery holder E 2S 2 Remove the old Lithium coin cell and install new one CR2025 Ensure that the side with the mark is up 3 Push the battery holder back into the remote control until you feel a click e Keep the battery out of the reach of children There is a danger of death by accidentally swallowing the battery Do not recharge the used battery or expose the battery to fire or water Do not dispose of the used battery along with household waste Dispose of used batteries according to local regulations Danger of explosion may happen if batteries are incorrectly replaced Replace only with the same type recommended by the manufacturer v ViewSonic 8 PJ551D Remote Control Operation Point the remote control at the infrared remote sensor and press a button NW Operating the projector from the front NW Operating the projector from the rear The remote control may not operate when there is sunlight or other strong light such as a fluorescent lamp shining on the remote sensor Operate the remote control from a position where the remote sensor is visible Do not drop the remote control or jolt it Keep the remote control out of locations with excessively high temperature or humidity Do not get water on the remote control or place wet objects on it Do not disassemble the remote control v ViewSonic 9 PJ551D Installation Connecting the Projector O VGA Cabl
24. ok into the lens when the lamp is on This can damage your eyes It is especially important that children are not allowed to look into the lens Powering Off the Projector 1 2 Press D button to turn off the projector lamp You will see a message Power off Press Power again appear on the screen Press b button again to confirm W The cooling fans continue to operate for cooling cycle W When the Lamp LED begins flashing the projector has entered stand by mode E f you want to turn the projector back on you must wait until the projector has completed the cooling cycle and has entered stand by mode Once in stand by mode simply press l button to restart the projector Disconnect the AC power cord from the electrical outlet and the projector Do not turn on the projector immediately following a power off procedure ViewSonic 11 PJ551D Adjusting the Projector Adjusting the Projector Height Tilt adjustment foot Elevator foot Elevator button The projector is equipped with an elevator foot to adjust the image height To raise or lower the image 1 To raise or lower the image press the elevator button and raise or lower the front of the projector Release the button to lock the adjustment 2 Tolevel the image on the screen turn the tilt adjustment foot to fine tune the height Wi To avoid damaging the projector make sure that the elevator foot and tilt adjustment foot are fully retracted before placi
25. ot change if it does you are adjusting the zoom not the focus W Check the projection lens to see if it needs cleaning If the image is flickering or unstable for a computer connection NW Press the Resync button on the control panel or the Auto button on the remote control NW Press the Menu button go to Computer Image and adjust Frequency or Tracking Remote control problems If the remote control does not operate NW Be sure nothing is blocking the remote control receiver on the front or back of the projector Use the remote control within the effective range W Aim the remote control at the screen or at the front or back of the projector W Move the remote control so it is more directly in front of or behind the projector and not as far to the side ViewSonic 24 PJ551D Customer Support For technical support or product service see the table below or contact your reseller Note You will need the product serial number Country Region Web Site T Telephone F Fax E mail Australia New Zealand www viewsonic com au AUS 1800 880 818 NZ 0800 008 822 service au viewsonic com Canada www viewsonic com T 1 866 463 4775 F 1 909 468 5814 service ca viewsonic com Europe Middle East Baltic countries North Africa www viewsoniceurope com Contact your reseller Hong Kong www hk viewsonic com T 852 3102 2900 service hk viewsonic com India www in viewsonic com T 1800 11
26. per lamp and in other lamps not specifically mentioned in the Annex of RoHS Directive 2 Lead in glass of cathode ray tubes electronic components fluorescent tubes and electronic ceramic parts e g plezoelectronic devices 3 Lead in high temperature type solders 1 e lead based alloys containing 85 by weight or more lead 4 Lead as an allotting element in steel containing up to 0 35 lead by weight aluminium containing up to 0 4 lead by weight and as a cooper alloy containing up to 4 lead by weight ViewSonic iii PJ551D Copyright Information Copyright ViewSonic Corporation 2007 All rights reserved Macintosh and Power Macintosh are registered trademarks of Apple Computer Inc Microsoft Windows Windows NT and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries ViewSonic the three birds logo OnView ViewMatch and ViewMeter are registered trademarks of ViewSonic Corporation VESA is a registered trademark of the Video Electronics Standards Association DPMS and DDC are trademarks of VESA PS 2 VGA and XGA are registered trademarks of International Business Machines Corporation Disclaimer ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein nor for incidental or consequential damages resulting from furnishing this material or the performance or use of this product In the interest of continuing produc
27. projector If the lamp does not turn on after the warm up period try reinstalling the lamp 9 Reset the lamp hour Refer to the Setting menu APN No Dispose of the used lamp according to local regulations Ensure that screws are tightened properly Screws not tightened fully may result in injury or accidents Since the lamp is made of glass do not drop the unit and do not scratch the glass Do not reuse the old lamp This could cause the lamp to explode Be sure to turn off the projector and unplug the AC power cord before replacing the lamp Do not use the projector with the lamp cover removed v ViewSonic 20 PJ551D Specifications Display Type Single 0 55 DLP panel Resolution Pixels XGA 1024 x 768 Lens Manual Zoom 1 1x Contrast Ratio 2000 1 Screen Size 30 250 Lamp 180W Input Output Source D Sub 15 pin S video composite video USB Video Compatibility NTSC 3 58 NTSC4 43 PAL 60 M N SECAM HDTV 480i p 576i p 720p 1080i Scanning Frequency Horizontal Freq 31 79 KHz Vertical Freq 50 85 Hz Noise Level Normal 36dB ECO 34dB Environment Operating Temperature 0 C to 40 C Humidity 3096 8596 Storage Temperature 20 C to 60 C Humidity 3096 8596 Power Requirement AC 100 240 V 50 60 Hz Power Consumption 230W Dimension 277 x 223 x 110 mm Weight 2 5 kg 5 5lb Note Design and Specifications are subject to change without prior notice ViewSonic 21 PJ551D Appendix
28. ssories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the unit When a cart is used use caution when moving the cart unit combination to avoid injury from tipping over Unplug this unit when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the unit has been damaged in any way such as if the power supply cord or plug is damaged if liquid is spilled onto or objects fall into the unit if the unit is exposed to rain or moisture or if the unit does not operate normally or has been dropped ViewSonic ii PJ551D Declaration of RoHS Compliance This product has been designed and manufactured in compliance with Directive 2002 95 EC of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment RoHS Directive and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee TAC as shown below Proposed Maximum Concentration Substance Actual Concentration Hexavalent Chromium C167 Polybrominated biphenyls PBB Polybrominated diphenyl ethers PBDE Certain components of products as stated above are exempted under the Annex of the RoHS Directives as noted below Examples of exempted components are 1 Mercury in compact fluorescent lamps not exceeding 5 mg
29. ste Electrical and Electronic Equipment Directive 2002 96 EC WEEE The mark indicates the requirement NOT to dispose the equipment as unsorted municipal waste but use the return and collection systems according to local law pd ViewSonic i PJ551D Important Safety Instructions 10 11 12 13 14 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this unit near water Clean with a soft dry cloth If still not clean see Cleaning the Display in this guide for further instructions Do not block any ventilation openings Install the unit in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other devices including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade and the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs Convenience receptacles and the point where they exit from the unit Be sure that the power outlet is located near the unit so that it is easily accessible Only use attachments acce
30. t improvement ViewSonic Corporation reserves the right to change product specifications without notice Information in this document may change without notice No part of this document may be copied reproduced or transmitted by any means for any purpose without prior written permission from ViewSonic Corporation Product Registration To meet your future needs and to receive any additional product information as it becomes available please register your product on the Internet at www viewsonic com The ViewSonic Wizard CD ROM also provides an opportunity for you to print the registration form which you may mail or fax to ViewSonic For Your Records Product Name PJ551D ViewSonic DLP Projector Model Number VS11973 Document Number PJ551D 2_UG_ENG Rev 1A 11 30 07 Serial Number Purchase Date CN The lamp in this product contains mercury Please dispose of in accordance with local state or federal laws ViewSonic iv PJ551D Contents Ji AAA 1 Projector FEU cd 1 Package Contents 2 eiie eie eire eicit tede eei deed 2 Projector OVEV EW i 3 Using the Product 5 Control Patriel c coria tur tni te oer e o a et e e dp 5 Connection Pot in irte presi iicet dif 6 Remote Control sida Replacing the Battery orien aqii 8 Remote Control Operation ccccccccsceeseeeesseeeeeeeeeeeesceeeeseeeseaeeeeeeesseeseneeeseeees 9 Installation neta dante renes
31. ty protects This warranty is valid only for the first consumer purchaser What the warranty does not cover 1 Any product on which the serial number has been defaced modified or removed 2 Damage deterioration or malfunction resulting from a Accident misuse neglect fire water lightning or other acts of nature unauthorized product modification or failure to follow instructions supplied with the product Repair or attempted repair by anyone not authorized by ViewSonic Any damage of the product due to shipment Removal or installation of the product Causes external to the product such as electric power fluctuations or failure Use of supplies or parts not meeting ViewSonic s specifications Normal wear and tear Any other cause which does not relate to a product defect 3 Any product exhibiting a condition commonly known as image burn in which results when a static image is displayed on the product for an extended period of time 4 Removal installation and set up service charges pero ap y How to get service 1 For information about receiving service under warranty contact ViewSonic Customer Support please refer to Customer Support page You will need to provide your product s serial number 2 To obtain warranted service you will be required to provide a the original dated sales slip b your name c your address d a description of the problem and e the serial number of the product 3 Ta
32. used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Warning You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment For Canada e This Class B digital apparatus complies with Canadian ICES 003 e Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada CE Conformity for European Countries The device complies with the requirements of the EEC directive 89 336 EEC 2004 108 C EEC as amended by 92 31 EEC and 93 68 EEC Art 5 with regard to Electromagnetic compatibility and 73 23 EEC as amended by 93 68 EEC Art 13 with regard to Safety Following information is only for EU member states The mark shown to the right is in compliance with the Wa
33. xico Av de la Palma 8 Piso 2 Despacho 203 Corporativo Interpalmas Col San Fernando Huixquilucan Estado de M xico Tel 55 3605 1099 http www viewsonic com la soporte index htm N MERO GRATIS DE ASISTENCIA T CNICA PARA TODO M XICO 001 866 823 2004 Hermosillo Distribuciones y Servicios Computacionales SA de CV Calle Juarez 284 local 2 Col Bugambilias C P 83140 Tel 01 66 22 14 9005 E Mail disc2 hmo megared net mx Puebla Pue Matriz RENTA Y DATOS S A DE C V Domicilio 29 SUR 721 COL LA PAZ 72160 PUEBLA PUE Tel 01 52 222 891 55 77 CON 10 LINEAS E Mail datos puebla megared net mx Chihuahua Soluciones Globales en Computaci n C Magisterio 3321 Col Magisterial Chihuahua Chih Tel 4136954 E Mail Cefeo soluglobales com Distrito Federal QPLUS S A de C V Av Coyoac n 931 Col Del Valle 03100 M xico D F Tel 01 52 55 50 00 27 35 E Mail gacosta qplus com mx Guerrero Acapulco GS Computaci n Grupo Sesicomp Progreso 6 A Colo Centro 39300 Acapulco Guerrero Tel 744 48 32627 Av Reforma No 403Gx39 y 41 M rida Yucat n M xico CP97000 Tel 52 999 925 1916 E Mail rrrb sureste com Tijuana STD Ay Ferrocarril Sonora 3780 L C Col 20 de Noviembre Tijuana Mexico 4 3 ViewSonic Mexico Limited Warranty ViewSonic 29 Villahermosa Compumantenimietnos Garantizados S A de C V AV GREGORIO MENDEZ 1504 COL FLORIDA C P 86040 Tel 01 993 3 52
Download Pdf Manuals
Related Search