Ultra Start 2250M User's Manual
Contents
1. On position Car Finder Mode 1 Press and hold the button for two seconds 2 The system will flash the park lights and chirp the siren five times This feature can help find your vehicle in a crowded parking lot Panic Mode 1 Press and hold the LOCK button for three seconds 2 The park lights will flash and the siren will activate PANIC MODE DISABLE 1 Press the LOCK button to disable the panic mode and to lock the doors 2 Press the UNLOCK button to disable the panic mode press the unlock button again to unlock the doors and disarm the alarm 3 Panic Mode will stay activated until disabled by the remote transmitter 2nd Car Operation See Dealer For Details gao amp 3 Press Once to Lock Doors Continue to hold for Panic Mode Press a 2nd Time and Hold for a Constant Lock Output 208 amp A Press Once for Unlock Doors and Disarm the Alarm Press and Hold for Trunk Aux Output gao amp 58 Press Once for Start 2 Times if programmed for safety start Press and Hold for 3 seconds while running to turn off cae Then ics amp 32 Press and Release then press START and hold for Timer Mode Diagnostics PARK LIGHTS 3 Flashes 3 Slow Flashes 4 Slow Flashes 5 Flashes 5 Slow Flashes 6 Flashes 7 Flashes 8 Flashes STATUS LED Series of 3 Flashes LED s On Solid Series of 4 Flashes Series of 5 Flashes Series of 5 Flashes Series of 6 Flashes Series of 7 Flashes Series2. steady Door locks and trunk release are still operational DEACTIVATING SERVICE MODE 1 While the ignition is ON press and hold the Program Button for five seconds The park lights will flash and the siren will chirp two times to confirm thatthe system has exited Service Mode 2 Remote start functions will return to normal operation Service Mode By Remote SERVICE MODE ACTIVATED 1 Press and release button 4 Button 2 Press and hold Button 4 Button for 6 seconds until Status LED comes on Steady Note The siren will chirp 5 times to confirm Service Mode was entered SERVICE MODE DEACTIVATED 1 Press and release Button 4 Button 2 Press and hold Button 4 Button for 6 seconds until Status LED turns off Note The siren will chirp 2 times to confirm Service Mode was exited Note The remote starter will flash the park lights 3 times if the start button is pressed when the vehicle is in Service Mode LIMITED LIFETIME WARRANTY Limited Lifetime Warranty Available with Professional Installation Only The manufacturer warrants to the original purchaser of their remote starters and alarms that the product shall be free from defects in material and workmanship However should this product be proven to be defective within a three year period from the original date of purchase the manufacturer will without charge to the purchaser excluding any charges incurred to have the product delivered to t
3. 3 Starting the vehicle with the key or by the remote will also cancel Timer Mode Self Learning Shock Sensor Press the lock button 5 times once every half second or until the siren chirps 3 times and the park lights turn Strike the vehicle with the amount of force wanted to trigger the alarm Strike the vehicle 3 times to set the impact level Each time the vehicle is impacted the siren will chip Press the unlock button to exit Shock Sensor Learning Temporary Sensor Bypass 1 Press and release the LOCK button The siren will chirp once 2 Within 3 seconds press and release the Button the siren will chirp once This feature can be used in bad weather or in areas with high levels of noise Airports Note The shock sensor will reset the next time the alarm is armed 2 2 RELAY DIAGRAMS sn Use 30A SPDT Automotive Type Relays Starter Kill with Bypass Units Transponder or Passlock 1 Cut the Starter Wire between the key and the start and connect to Pins 87a amp 30 of the relay _ Bypass Unit 2 Connect the Constant Power wire for the Bypass Unit to Ignition and not Constant Power 3 Connect the negative when run input from the bypass unit and pin 86 of the starter kill relay to the Orange Wire of the main unit Diode Isolate if needed Program Unit for Starter Kill Bypass Operation SEE PROGRAM MODE 3 SETTI
4. 4 Press the lock or unlock button to exit Shock Sensor learning Your Basic Install ls Complete INSTALLATION GUIDE a DPS Programming Overview Program mode allows you to adjust the settings and options of your system Your system has been intelligently designed by installers with years of experience The system s default settings do not require any program changes in most cases However this system does incorporate a highly advanced programming system that includes 4 menus with numerous options and settings that can be easily adjusted for custom installations and applications Menu 1 User Settings Page 8 This program menu contains settings that adjust the way the system operates for the user Menu 2 Alarm Settings Page 9 This program menu contains settings that adjust the way the system operates for the user Menu 3 Starter Settings Page 10 This menu controls features and settings associated with remote car starter applications Menu 4 Tach Settings Page 11 This menu allows the programming of the tach signal and the manual adjustment of that setting Entering Program Mode To Enter Program Mode 1 Make sure ignition is in the off position 2 Within three seconds turn the key ON OFF ON OFF ON Leave in the ON position 3 Press and release the Program Button on the antenna one time 4 The park lights will come on and the siren will chirp to confirm entering Program Mode 5 Select the Des
5. Button 2 times The Led will start flashing 2 times Step 4 Hold the Program Button For 5 seconds until parking lights flash each time lights flash the tach is reduced Step 5 Release the Program Button Exit Program Mode and test the remote start Setting 3 Adjust For Under Crank Tach or Tachless Step 1 Enter Program Mode Ignition ON OFF ON OFF ON then press the Program button on the antenna 1 time Step 2 Enter Program Menu 4 Press button 4 on the remote transmitter Button Step 3 Press the Program Button 3 times The Led will start flashing 3 times Step 4 Hold the Program Button For 5 seconds until parking lights flash each time lights flash the tach is increased Step 5 Release the Program Button Exit Program Mode and test the remote start Shock Sensor Self Learn Mode 1 Press the LOCK button 5 times once every second 2 The system will chirp the siren 3 times upon last press and the park lights will flash 3 times then stay On during the adjustment mode 3 Within 10 seconds impact the vehicle three times with the amount of force you want to activate alarm The siren will chirp upon sensing the impact 4 Press the unlock button to exit Adjustment Mode 5 Arm the system wait 10 seconds and test sensor Note Repeat the above steps to adjust the setting of the sensor Anti Car Jacking Mode ENSURE THAT USER IS FULLY TRAINED ON THIS FEATURE ONLY USE THIS FEATURE WHEN S
6. Button Press momentarily to move to next program step or repeat to change selection INSTALLATION GUIDE J PROGRAMMING 2290 PROGRAM MODE TACH SETTINGS Setting 1 Tach Selection TL_Models Only 1 Tach Detection Mode 1 Honk Chirp Must connect Tach Wire Blue White on 14 pin connector 2 Tachless Mode 2 Honks Chirps No Tach connection required Do not connect the tach wire Note The system must be Tach Tachless learned before the vehicle will remote start Setting 1 Method 2 Low Idle Tach Learning This option is used for vehicles that maintain a HIGH or erratic idle after starting and need more that 10 seconds to establish a stable idle Step 1 Enter Program Mode Ignition ON OFF ON OFF ON then press the Program button on the antenna 1 time Step 2 Enter Program Menu 4 Press button 4 on the remote transmitter Button Step 3 Start Vehicle Using the ignition key make sure not to turn the key off at any time or your will exit programming Step 4 Press the Program Button One time The Led will start flashing in single cycles Press and hold the Program Button for 5 seconds The park lights will flash twice when the tach signal is learned Setting 2 Adjust For Over Crank Tach or Tachless Step 1 Enter Program Mode Ignition ON OFF ON OFF ON then press the Program button on the antenna 1 time Step 2 Enter Program Menu 4 Press button 4 on the remote transmitter Button Step 3 Press the Program
7. Disabled 1 Flash Honks for Panic and Car Finder Mode only 2 Lock amp Unlock chirps Enabled 2 Flashes Honks for Lock Unlock Panic and Car Finder Mode Only 3 All chirps enabled 3 Flashes Honks for Lock Unlock Start Panic and Car Finder Mode Press the Program Button 2 times to select setting 2 This will be confirmed by 2 LED flashes Press and hold the Program Button until you receive the appropriate of park light flashes and siren chirps Release the Program Button Press momentarily to move to next program step or repeat to change selection Setting 3 Door Lock Options 1 Double Pulse Unlock 1 Flash Single 5sec Lock pulse and double Unlock Pulse 2 3 Second Lock amp Unlock 2 Flashes 3 second pulses for Lock amp Unlock 3 0 75 Second Pulses 3 Flashes 0 75 second pulses for Lock and Unlock Press the Program Button 3 times to select setting 3 This will be confirmed by 3 LED flashes Press and hold the Program Button until you receive the appropriate of park light flashes and siren chirps Release the Program Button Press momentarily to move to next program step or repeat to change selection Note See Setting 7 to adjust the door lock pulse duration to 125ms Setting 4 Sensor Enable Disable 1 Sensors Disabled 1 Flash Impact Sensors Disabled 2 Sensors Enabled 2 Flashes Impact Sensors Enabled Normal Operation Press the Program Button 4 times to select setting 4 This will be confirmed by 4 LED flashes Press and ho
8. Select a location under the dash to install the main module Be certain that the module is securely attached and does not obstruct any serviceable areas Do not force or jam the module into tight places instead of mounting The module must be free from all moving parts such as brake clutch and gas pedal linkages Do not place the module directly in front of a heater vent Testing The System When the installation is complete it will be necessary to test that the system is working correctly The system s default programming will work on the majority of vehicles but might need to be adjusted for some applications If the installation requires special timing or additional features proceed to Program Mode ATTENTION The Hood Pin Safety Switch MUST always be connected NOTE Always inform user to place system in Service Mode before any service Work is performed on the vehicle INSTALLATION GUIDE OO WIRING CONNECTIONS 2250 6 Pin Power Connector Yellow Starter 30amp output 12volts during crank only Green Heater 30amp output 12volts in accessory Off during start Red 12 power 30amp input Constant 12volt power at ignition harness Red 12 power 30amp input Constant 12volt power at ignition harness Blue Ignition 1 30amp output 12volts in ignition and start positions White Select Out 30amp output Selectable Output See jumper diagram 14 Pin Connector Yellow Re Arm 0 75sec Pulse With Lock And On Shutdown Red White 3rd CH Tru
9. of 8 Flashes DIAGNOSTIC CODE Door Opened M Models System Is In Service Mode Not in Reservation Mode M units Brake Pedal Shutdown Ignition On During Start Attempt Hood Pin Grounded Tach Lock Out 3 Start Attempts with no start INSTALLATION GUIDE OPERATIONS 2725 0 Reservation Mode Manual Transmissions Only 1 With the vehicle running apply the park brake then press and release the brake pedal 2 The park lights will flash and the siren will chirp to confirm that reservation mode has been activated 3 Remove the key from Ignition and exit the vehicle the vehicle will remain running 4 Close the door and the vehicle will shut off If the vehicle has a delay dome light the vehicle may run until the dome light turns off 5 The vehicle is now in Reservation Mode and may be remote started Note Opening qoi after this point will cancel Reservation Mode emote star 1 Press and release the sutton 2 The park lights will flash and the siren will chirp once 3 When the vehicle has started the system will flash the park lights four times and then remain On while the vehicle is running 4 The vehicle will continue to run for the programmed runtime normally 15 minutes EXTEND RUNTIME 1 Press and release the Sutton while the vehicle is remote started 2 The system will respond with one park light flash and one siren chirp to confirm Extended Runtime The system will reset the run time normal
10. INSTALLATION GUIDE QQEO IN Advanced Remote Vehicle Starter With Alarm System AUTOMATIC AND MANUAL TRANSMISSION MODELS WWW ULTRASTARTERS COM See website for a full size printable version of this manual WARNING NEVER INSTALL A AUTOMATIC REMOTE STARTER IN A MANUAL TRANSMISSION VEHICLE SERIOUS INJURY OR DEATH CAN RESULT FCC ID Notice This device complies with Part 15 of the FCC rules Operation is subject to the following conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including TECH SUPPORT interference that may cause undesired operation CAUTION Changes or modifications not expressly approved by the part responsible for compliance void the user s authority to operate this devise E Mail Tech Support support ultrastarters com Check Our Web Site www ultrastarters com 727255 0 Faces OOK TTS 2250 Wiring Diagram Page 3 Pre Installation Page 4 Components Recommended Pre Installation Procedures Recommended Install Procedures Wire Connectors Page 5 6 Pin Connector 14 Pin Connector 3 Pin Red Connector 4 Pin Blue Connector Jumper Selections Installation Page 6 Basic Installation Quick start Plugging In The Module Auto Tach Learn Shock Sensor Programming Programming Page 7 11 Program Overview amp System Reset Program Menu 1 User Settings Program Menu 2 Alarm Settings Program Menu 3 Star
11. NG 6 Negative Type Door Locks Vehicle To Control Lock Unlock Relay or Switch Actuators Positive Type Door Locks Un Vehicle Lock Lock Unlock lock Switch Fused 12V el Green Blue eI To Control Relay f i or Actuator 5 Wire Reverse Polarity Type Door Locks Vehicle Lock Unlock ToActuator f Un Switch Vacuum Type Door Locks Fused 12V eee G eA a lel a o Vacuum Un Pump
12. PECIFICALLY REQUESTED ENSURE THAT USER IS TRAINED ON THE OPERATION OF THIS FEATURE IF NOT UNWANTED RESULTS MAY ARISE When activated the system waits 30 seconds then flashes LED rapidly for 30 seconds then chirps siren as a warning for 10 seconds then goes into full alarm ACTIVATING CAR JACK MODEProgrammable Mode 1 Mode 2 Activates upon any of the following steps Mode 1 amp 2 While the ignition Key is On press and release button 4 Mode 1 amp 2 Open the vehicles door while the ignition key is On Mode 2 only Each and every time that the ignition key is turned On DEACTIVATING CAR JACK MODE 1 During countdown Turn ignition off amp on then press and release the Program Button 2 After full alarm Turn ignition off amp on the hold the Program Button for 8 seconds 72725 0 opsRATIONS INSTALLATION GUIDE Ii Reservation Mode Manual Trans Manual Transmission Remote Starters must have both the door trigger and park brake wires connected Most installs will require a clutch bypass This is a temporary bypass The clutch should only be bypassed during the activation of the remote starter Never disconnect or alter the switch to be always bypassed Always use a M Series Remote Starter on a manual transmission vehicle Never install a automatic Remote Starter model into a manual transmission vehicle It is not recommended to install a remote starter on a convertible type vehic
13. ck and on disarm output 75 second Press the Program Button 7 times to select setting 7 This will be confirmed by 7 LED flashes Press and hold the Program Button until you receive the appropriate of park light flashes and siren chirps Release the Program Button Press momentarily to move to next program step or repeat to change selection r 8 Programming this option will change the pulse length of this output from 750ms to a Much shorter pulse of 125ms he ee 2 250 PROGRAM MODE ALARM SETTINGS Enter Alarm Program Mode See Page 7 for details on entering program mode Setting 1 Secure Valet Mode 1 Secure Valet Active 1 Flash Valet only if ignition ON and Program Button is held for 15 seconds 2 Normal Valet Active 2 Flashes Valet if ignition ON and Program Button is held for 5 seconds Press the Program Button 1 time to select setting 1 This will be confirmed by 1 LED flash Press and hold the Program Button until you receive the appropriate of park light flashes and siren chirps Release the Program Button Press momentarily to move to next program step or repeat to change selection Setting 2 Parking Light Output 1 30 Second Parking Lights on Disarm 1 Flash Park Lights on for 30 seconds on disarm 2 Negative Park Light 2 Flashes Switches the Park Light and the Trunk Release 3rd Ch Outputs 3 Normal Parking Lights 3 Flashes 2 Park Light Flashes on disarm Press the Program Button 2 times to sele
14. ct setting 2 This will be confirmed by 2 LED flashes Press and hold the Program Button until you receive the appropriate of park light flashes and siren chirps Release the Program Button Press momentarily to move to next program step or repeat to change selection Setting 3 Horn Honk Timing Unit Must be set for Horn Output in Setting 5 1 5ms 1 Flash Short Quiet Pulses 2 20ms 2 Flashes Long Loud Pulses 3 10ms 3 Flashes Normal Medium Pulses Press the Program Button 3 times to select setting 3 This will be confirmed by 3 LED flashes Press and hold the Program Button until you receive the appropriate of park light flashes and siren chirps Release the Program Button Press momentarily to move to next program step or repeat to change selection Setting 4 Car Jack Mode 1Door amp Button 1 Flash Activated by pressing Button 4 or opening the door while the Ignition is ON 2Door Button 4 2 Flashes Activated by pressing Button 4 or opening the door while the Ignition is ON 3 Car Jack OFF 3 Flashes No Car Jack Press the Program Button 4 times to select setting 4 This will be confirmed by 4 LED flashes Press and hold the Program Button until you receive the appropriate of park light flashes and siren chirps Release the Program Button Press momentarily to move to next program step or repeat to change selection Setting 5 Siren Horn Output 1 Horn Honk 1 Flash Pulses when alarm is triggered Timing can be pr
15. es 5 sec Max time that starter will stay engaged Press the Program Button 5 times to select setting 5 This will be confirmed by 5 LED flashes Press and hold the Program Button until you receive the appropriate of park light flashes and siren chirps _ Release the Program Button Press momentarily to move to next program step or repeat to change selection Setting 6 Starter Kill Bypass Module Output Orange wire on 14 Pin Con 1 Active Starter Kill 1 Flash On when locked Before ignition and 2 seconds after ignition turns off 2 Passive Starter Kill 2 Flashes Same as setting 1 but will arm 60sec after the ignition turns off 3 Bypass Module 3 Flashes Output before ignition Stays on 2 seconds after ignition turns off Press the Program Button 6 times to select setting 6 This will be confirmed by 6 LED flashes Press and hold the Program Button until you receive the appropriate of park light flashes and siren chirps Release the Program Button Press momentarily to move to next program step or repeat to change selection Setting 7 Safety Start Mode 1 Safety ON 1 Flash Must press the start button twice to remote start vehicle 2 Safety OFF 2 Flashes Press the start button once to remote start vehicle Press the Program Button 7 times to select setting 7 This will be confirmed by 7 LED flashes Press and hold the Program Button until you receive the appropriate of park light flashes and siren chirps Release the Program
16. f the System The manufacturer does not guarantee or insure against theft of the vehicle or its contents Alarm models are designed only to act as a deterrent against possible theft This alarm may qualify for auto insurance discounts contact your Insurance Agent for further information The manufacturer shall not be held liable for any consequential damages due to breach of this or any other warranty expressed or implied This warranty gives you specific legal rights Your specific legal rights may vary for each region CERTAIN DAMAGES EXCLUDED The manufacturer expressly disclaims any liability or responsibility for incidental damages caused by the product including economic loss loss of use of the product car rentals or any other costs relating to the care and custody of the product The manufacturer disclaims liability or responsibility for any consequential damages caused by the product or resulting from its use including the cost of repairing or replacing other property damaged by the product or caused by its use whether or not the product is working properly The product is intended to deter unauthorized use of the vehicles in which it is installed The manufacturer does not warrant that the product is fool safe against theft and or vandalism and or human error or misuse The manufacturer accepts no liability or responsibility for any damage of any kind whatsoever caused to any vehicle in which the product is installed or any resulting damage from
17. ghts will turn on Continue holding the Button Step 4 Press the LOCK button on each of 1st car remote s and press the button on each of the 2nd car remote s to be programmed The park lights will flash once and the siren will chirp once each time a new code is learned Note Transmitter programming must done quickly Do not pause more than one second between each transmitter All the transmitters to be used must be programmed at the same time All transmitters not programmed at this time will be erased from memory for security The system holds a maximum of 4 transmitter codes including 2nd car remote codes You can program the same remote as a 1st car remote in one vehicle and as a 2nd car remote ina second vehicle Battery Replacement The transmitter battery should be changed at least once every year to maintain proper operating range Replace with quality23A 12volt Alkaline battery D lt e Carefully remove the Remove top case Repl t Test tef screw from back of then replace the P Ee a Re install screw proper operation the remote battery INSTALLATION GUIDE DAIS System Service Mode ACTIVATING SERVICE MODE 1 While the ignition is ON press and hold the Program Button for five seconds The park lights will flash and the siren will chirp five times to confirm that the system is in Service Mode 2 While in Service Mode the remote start functions will be disabled and LED s will be ON
18. he manufacturer repair or replace any part of the remote starter and or alarm which the manufacturer agrees to be defective After the initial three year period a labour charge of no greater than 20 00 will apply to all defective goods A 20 00 check must accompany any goods being returned to the manufacturer All warranties apply on to the original purchaser and the vehicle in which it is originally installed Repairs or replacement of defective modules shall remain at the discretion of the manufacturer All other parts components accessories and or optional equipment pertaining to the remote starter and alarm are not included in the manufacturer s warranty This warranty is non transferable Request for warranty service from any Factory Authorized Dealer must be accompanied with the original purchase receipt or have product registered by authorized dealer on manufacturer s website Failure to comply with any of these conditions may result in warranty being voided If unit in not installed by an Authorized Dealer warranty term is limited to 15 day from date of purchase and covers manufacturing defects ONLY Only freight pre paid shipments will be accepted for warranty This warranty does not cover the following removal and reinstall labor charges shipping charges abuse misuse or accidental damages to the remote starter and alarm automobile and or parts there of This warranty is void upon modification repairs or alterations of any part o
19. ion selected within the setting 5 Turn the ignition key Off to exit Program Mode Note This procedure is listed below each program setting on pages 8 11 of this manual SYSTEM RESET STEP 1 Within three seconds turn the key ON OFF ON OFF ON Leaving Key ON STEP 2 Press and release the Program Button STEP 3 The park Lights will turn ON STEP 4 Press and hold the program button again for 8 seconds until the park lights flash and the siren will chirps three times The system is now re set to factory defaults Note Reset to defaults resets the tach learning and any setting that may have been changed in the program menus but does not delete the transmitters from memory 2 25 0 pReeranmanre INSTALLATION GUIDE a PROGRAM MODE USER SETTINGS Setting 1 Ignition Auto Lock 1 Ignition Lock amp Unlock Enabled 1 Light Flash Doors Lock Unlock when the key is turned On Off 2 Ignition Lock Only 2 Light Flashes Doors Lock when ignition key is turned ON only 3 Ignition Auto Lock Disabled 3 Light Flashes Doors do not Lock or Unlock with Ignition key Press the Program Button 1 time to select setting 1 This will be confirmed by 1 LED flash Press and hold the Program Button until you receive the appropriate of park light flashes and siren chirps Release the Program Button Press momentarily to move to next program step or repeat to change selection Setting 2 Horn Honk Settings 1 Lock amp Unlock chirps
20. ired Program Menu Press Button 1 Lock User Options Page 8 Press Button 2 Unlock Alarm Options Page 9 Press Button 3 Start Remote Start Options Page 10 Press Button 4 Aux Tach Adjustment Menu Page 11 6 The selected mode will be confirmed by a siren chirp and one park light flash 7 The Program Menu may be changed at any time by pressing the transmitter buttons as above this allows the installer to change a setting from one menu then quickly jump to another menu without re entering the Program Mode 8 To exit Program Mode turn the ignition key OFF or wait 30 second and the system will exit automatically Note f the unit does not enter Program Mode turn the ignition off for five seconds and repeat steps 1 4 The first ignition Blue wire MUST be connected to the vehicle s first ignition wire If it is not connected it will not be possible to enter the Program Modes Changing the Programmable Settings To Select and Change A Program Setting 1 Enter Program Mode 2 Select the desired Program Menu See pages 8 11 3 Press amp release the Program Button the correct number of times to select the desired Program Setting as listed on pages 8 11 The park lights will flash and the siren will chirp to indicate the current setting that is selected 4 Press and hold the Program Button until the parking lights siren confirm the selected setting The park lights will flash and the siren will chirp to indicate the opt
21. its use The manufacturer accepts no responsibility or liability for any damage resulting to or theft of the vehicle or its contents 27 gt 5 0 OPERATIONS INSTALLATION GUIDE _ Lock Doors amp Arm The Alarm 1 Press and release the LOCK button on the remote transmitter 2 The park lights will flash and the siren will chirp once 3 The doors will lock With Optional Keyless Entry 4 The LED s on the antenna will start flashing within five seconds Unlock Doors amp Disarm The Alarm 1 Press and release the UNLOCK button on the remote transmitter 2 The park lights will flash and the siren will chirp twice 3 The doors will unlock With Optional Keyless Entry 4 The LED s on the antenna will stop flashing Silent Arm And Disarm 1 Press and release the LOCK amp UNLOCK buttons at the same time 2 f the doors are locked this will unlock the doors without siren chirps the park lights will flash two times to confirm the doors have unlocked 3 If the doors are unlocked this will lock the doors without siren chirps the park lights will flash one time to confirm the doors have locked Trunk Release _ 1 Press and hold the UNLOCK button for three seconds 2 The doors will unlock continue holding the unlock button for three more seconds the trunk release will then activate The trunk release will be confirmed by one park light flash 3 For safety reasons trunk release will not activate when ignition key is in the
22. ld the Program Button until you receive the appropriate of park light flashes and siren chirps Release the Program Button Press momentarily to move to next program step or repeat to change selection Setting 5 Passive Active Arming 1 Passive Arming 1 Flash Auto Arms 30 seconds after last door is closed 2 Active Arming With Rearm 2 Flashes If unlock is pressed and no door is opened within 30sec 3 Active Armin 3 Flashes Alarm Arms Only with Transmitter Press the Program Button 5 times to select setting 5 This will be confirmed by 5 LED flashes Press and hold the Program Button until you receive the appropriate of park light flashes and siren chirps Release the Program Button Press momentarily to move to next program step or repeat to change selection Setting 6 Active Passive Locks 1 No Auto Lock with Passive Arm 1 Flash Doors do not auto lock with passive arming 2 Doors Auto Lock with Passive 2 Flashes DOORS LOCK WHEN PASSIVE ARMING Press the Program Button 6 times to select setting 6 This will be confirmed by 6 LED flashes Press and hold the Program Button until you receive the appropriate of park light flashes and siren chirps Release the Program Button Press momentarily to move to next program step or repeat to change selection Setting 7 Door Unlock amp Disarm Pulse Duration 1 Short Pulses 1 Flash 125ms pulses with Unlock and on disarm output 125 second 2 Normal 2 Flashes 750ms pulses with Lock Unlo
23. le If doing so It is highly recommended that a radar sensor is installed to cover the proximity of the gear shift lever If the radar sensor Is tripped the remote starter will exit Reservation Mode To enter Reservation Mode the following steps must be followed Step 1 While the vehicle is running place the transmission in neutral and apply the parking brake Step 2 Press and release the brake pedal The park lights will activate Step 3 Turn the ignition key off and the vehicle will stay running Step 4 Exit the vehicle and close the door The vehicle will then shut off Step 5 The vehicle can now be safely remote started NOTE If the vehicle has a dome light delay the vehicle may stay running until the dome light turns off This is normally no longer than 30 seconds Reservation Mode will automatically be exited if the doors of the vehicle are opened The set up mode will then have to be repeated Reservation Mode Must be set up each time the vehicle is parked Note If the vehicle is not in Reservation Mode and the Start button is pressed the system will flash the park lights four times slowly Transmitter Programming Step 1 Within three seconds turn the ignition Key ON OFF ON OFF ON Leaving Key ON Step 2 Press and hold the Program button Parking Lights will come ON if park lights do not come on at this point turn key off for 5 seconds the repeat step 1 Step 3 Continue to hold the Program button The park li
24. ly 15 minutes Remote Stop 1 Press and hold the button for three seconds The remote starter will shut down 2 The park lights will flash two times and the siren will chirp two times Note Pressing the brake pedal or opening hood will also stop the vehicle Idle Mode _ 1 While the vehicle is running with key press the sgebutton 2 The park lights will turn on and the siren will chirp once 3 Turn the ignition key Off and the vehicle will continue to run 4 Exit the vehicle and leave it running safely without the keys in the ignition Lock the door while the vehicle is left running Turbo Timer Mode 1 While the vehicle is running with key press the button 2 The park lights will turn on and the siren will chirp once 3 Turn the ignition key Off and the vehicle will continue to run for 2 minutes Timer Mode eee 1 Press and release the button then press and hold the button for six seconds until The parking lights turn On 2 While the parking lights are on the start cycle can be selected 1 hour cycle Press LOCK button 1 Park Light Flash 2 hour cycle Press UNLOCK button 2 Park Light Flashes 3 hour cycle Press x button 3 flashes 4 hour cycle Press button 4 flashes 3 System will start vehicle at selected cycle for up to 24 hours To Cancel Timer Mode 1 Press and release the button then press and hold the button for four seconds 2 The park lights will flash and the siren will chirp twice
25. mper Selections Position One Second Starter Output On the White Wire From The 6 Pin Connector Position Two Second Accessory Output On The White Wire From The 6 Pin Connector Position Three Second Ignition Output On The White Wire From The 6 Pin Connector The Default Setting For The System Is Second Ignition Output To change the jumper position you must first remove the access cover as shown in the diagram below The access cover will slide out of its position when pushed outwards from the center of the module The jumpers control the output on the white wire from the six pin harness To change the output of this wire place the jumper in one of the following positions Note The default setting is second ignition Output on White wire Jumper position Second Starter Second Ignition Position 3 2250 QUICK STARTINS I SE dean Step 1 Connect All Of the Following Wires 6 Pin Power Connector Yellow Starter Output Connect The Yellow Wire From The 6 Pin To The Vehicles Starter Wire Green Heater Output Connect The Green Wire From The 6 Pin To The VehiclesAccessory Wire Red 12 power Input Connect to Constant 12 Volt Power Source High Current Red 12 power Input Connect to Constant 12 Volt Power Source High Current Blue Ignition 1 Output Connect The Blue Wire To the Vehicles Primary Ignition Wire White Selectable Output Select Jumper Position If Necessary See Page 5 14 Pi
26. n Power Connector Black System Ground Connect The Black Wire To Chassis Ground Pink Brake Switch Connect The Pink Wire To The Brake Switch When Brake is Applied White Park Lights Connect The White Wire To Park Light System Green White Hood Switch Connect The Green White Wire To The Hood Pin Switch Blue White Tach Input Connect The Blue White Wire To AnA C Tach Source Must Be Above 2volts A C White Blue Siren Horn Connect The White Blue Wire To A Siren or To A Horn Wire Green or Door Input Connect The Green Wire On Vehicles With Negative Door Pin Systems Purple Door Input Connect The Purple Wire On Vehicle With Positive Door Pin Systems Manual Transmissions Only O Black White Park Brake Connect Parking Brake Manual transmission vehicles must have a M Series Remote Starter Installed Manual Transmission Units Must Be Placed Into Reservation Mode To Operate See Page 12 Step 2 Plug In The Module When all the connections are done the control module can be plugged in Before connecting the control module make sure the ignition is in the OFF position Plug in the 6 pin harness then the 14 pin followed by any other connectors that were used Step 3 Auto Tach Tachless Learn Tach Learning 1 Make all the required wire connections and plug in the Unit The park lights should flash twice upon power up 2 Turn the Ignition Key ON The Park Lights will turn on 3 Start the vehicle with
27. ngines Recommended Installation Procedures Proper Connections Remote Starters can handle loads of up to 30 amps for extended periods of time It is CRITICAL to insure that ALL high current connections are properly soldered and insulated with quality electrical tape Failing to insure proper connections will result in warranty being VOID and can result in a FIRE The manufacturer is not responsible for any such damages It only takes a few more minutes to do the job RIGHT Under Hood Connections Route the hood pin and tach wires through the firewall into the engine compartment Always try to pull the wires through a factory rubber grommet If drilling through the firewall BE CAREFUL Check for obstructions on both sides of the firewall After drilling use a snap in grommet to protect the wires from sharp edges Installing the External Long Range Antenna To insure the best possible reception place the antenna in the center of the windshield behind the rear view mirror Before attaching to the glass ensure that the surface is clean and dry For best results with range place the antenna below the tint screen Run the cable under the headliner and behind the A pillar panel Be careful not to pinch the antenna cable Plug the antenna into the BLUE connector on the Control Module NOTE This step is not used on Alarm Only Units with no External Antenna Mounting The Control Module Never mount the module in the engine compartment
28. nk Release Active When Button 2 Is Held For 3seconds Brown Disarm 0 75sec Pulse With Unlock And Before Start Orange Output While Running While Locked Starter Program Mode White Blue Siren Horn Siren Horn Output User amp Alarm Program Modes Black White Park Brake Negative Park Brake Input Manual Transmission Models Only Purple Door Input Positive Door Trigger Input Manual Trans amp Alarm Units Only White Park Lights Positive Park light Output 70 Amp Max Green White Hood Pin Negative Hood Pin Input MUST BE CONNECTED Green Door Negative Door Trigger Input Manual Trans amp Alarm Units Only Black Ground System Ground Input MUST BE CONNECTED Pink Brake Positive Brake Input MUST BE CONNECTED Blue White Tach Tach Signal Input MUST BE CONNECTED ON TACH MODELS Blue Glow Plug Programmable Input DIESEL ONLY Starter Program Mode 3 Pin Connector Red Green Door Lock Door Lock Output Programmable Menu 1 Setting 3 Blue Door Unlock Door Unlock Output Programmable Menu 1 Setting 3 Note The center pin of this relay is low current and designed to power a voltage inverter Do not use the center pin of this connector to power relay packs Doing so will damage the output Always use a fused power source when installing relays for keyless entry 4 Pin Connector Blue Antenna Program Button Connector The Antenna Must Be Connected Before the System will Operate Ju
29. ogrammed by Setting 4 2 Siren Output 2 Flashes Output on steady when alarm is triggered Press the Program Button 5 times to select setting 5 This will be confirmed by 5 LED flashes Press and hold the Program Button until you receive the appropriate of park light flashes and siren chirps Release the Program Button Press momentarily to move to next program step or repeat to change selection DDE INSTALLATION GUIDE PROGRAMMING _ Ea PROGRAM MODE STARTER SETTINGS Setting 1 Special Door Lock Unlock Operations 1 Type 1 1 Flash Unlock before start and a lock pulse after start amp shutdown 2 Type 2 2 Flashes Lock pulse after remote starter shuts off 3 Normal Operation 3 Flashes No additional re lock pulses Press the Program Button 1 time to select setting 1 This will be confirmed by 1 LED flash Press and hold the Program Button until you receive the appropriate of park light flashes and siren chirps Release the Program Button Press momentarily to move to next program step or repeat to change selection Setting 2 Gas Diesel Mode Blue Wire on 14 Pin Negative Input 30seconds 1 Flash Waits a maximum 30 seconds before starting 2Timed Delay 15 Seconds 2 Flashes Ignition ON for 15 seconds before engaging remote starter 3 Gas Positive Glow Plug 3 Flashes Waits 2 seconds to start if no diesel input is detected Press the Program Button 2 times to select setting 2 This will be confirmed by 2 LED flashes Press and h
30. old the Program Button until you receive the appropriate of park light flashes and siren chirps Release the Program Button Press momentarily to move to next program step or repeat to change selection Setting 3 Rearm Output Yellow Wire on 14 Pin 1 Type 1 1 Flash Pulse after start and with lock 2 Type 2 2 Flashes Pulse after start only 3 Factory Re arm 3 Flashes 0 75 second pulse with lock and after shutdown Press the Program Button 3 times to select setting 3 This will be confirmed by 3 LED flashes Press and hold the Program Button until you receive the appropriate of park light flashes and siren chirps Release the Program Button Press momentarily to move to next program step or repeat to change selection Setting 4 Run Time 1 30 Min Run Time 1 Flash Remote Starter runs for 30min when activated 2 45 Min Run Time 2 Flashes Remote Starter runs for 45min when activated 3 15 Min Run Time 3 Flashes Remote Starter runs for 15 min when activated Press the Program Button 4 times to select setting 4 This will be confirmed by 4 LED flashes Press and hold the Program Button until you receive the appropriate of park light flashes and siren chirps Release the Program Button Press momentarily to move to next program step or repeat to change selection Setting 5 Maximum Crank Time 110 Seconds 1 Flash 10 sec Max time that starter will stay engaged 23 Seconds 2 Flashes 3 sec Max time that starter will stay engaged 3 5 seconds 3 Flash
31. onnector to power relay packs Doing so will damage the output Always use a fused power source when installing relays for keyless entry 500ma Output Door Lock Output ACTIVE RF ANTENNA Program Button Status Led s NA _ Output on White wire Jumper position Second Starter Second Ignition Position3 The jumpers control the output on the white wire from the six pin harness Place the jumpers in the above order to change the output Note The default setting is second ignition 123 alai INSTALLATION GUIDE 2 25 0 INSTALLATION FIRS _ _ Components Control module Remote transmitter s Antenna with built in program button and LED s 6 pin main harness with dual 30amp power inputs 14 pin harness 3 pin 2 wire keyless entry harness Multi tone siren Hood pin safety switch Hood and window stickers Installation guide Owners manual Recommended Pre Installation Procedures BEFORE STARTING INSTALLATION Discuss the optional features with the customer Take a few minutes to review the installation and owners manuals Check if the vehicle has a factory security or anti theft system If equipped inform the customer of addition parts and labour Do a walk around the vehicle and check for any damage If installing a LED discuss the placement with customer before installing Note This remote starter is designed for fuel injected and diesel e
32. ter Settings Program Menu 4 Tach Settings Other Features And Operations Page 12 Reservation Mode Transmitter Programming Battery Replacement Service Mode System Operation Page 14 15 Relay Diagrams Page1 DIAGNOSTICS l PARK LIGHTS STATUS LED DIAGNOSTIC CODE 3 Flashes Series of 3 Flashes Door Opened M Models 3 Slow Flashes No Flashes Attempted Start In Service Mode 4 Slow Flashes Series of 4 Flashes Not in Reservation Mode M unit 5 Flashes Series of 5 Flashes Hood Pin Grounded Open 5 Slow Flashes Series of 5 Flashes Brake Pedal Shutdown 6 Flashes Series of 6 Flashes Ignition On During Start Attempt 6 Slow Flashes Series of 6 Flashes Hood Pin Grounded _ 7 Flashes Series of 7 Flashes Tach Lock Out 8 Flashes Series of 8 Flashes 3 Start Attempts with no start If the remote starter has a failed start attempt or if a safety input is activated the Diagnostic Memory will store up to four shutdowns in memory This information can then be accessed to determine the source of the shutdown To Enter Diagnostic Mode Step 1 Turn the ignition on wait two seconds then turn off Press the Program Button and release Step 2 The system will respond with three park light flashes and the siren will chirp the same number of times as the events in memory Maximum four events four chirps NOTE If the siren does not chirp there are no events in memory Step 3 Press the Program Button once to vie
33. the key the LED s on antenna will come when proper tach signal is detected After 30 seconds the park lights will turn off then flash twice to confirm Tach learning The system will flash the park lights seven times if not Tach Tachless learned and the start button is pressed The system must be Tach Tachless learned before remote starting If the LED s do not come on during tach learn a proper Tach signal was not detected Note If the park lights do not flash in auto tach learn mode it may be necessary to connect to a different tach source For best results connect the tach to the coil pack or to a fuel injector wire Tachless Learning TL Models Only 1 Follow Steps 1 amp 2 from above 2 Start the vehicle with the key the LED s on antenna will turn on after 30 seconds then park lights will turn off then flash twice to confirm Tachless learning Note If the first ignition wire is connected to a wire that does not stay 12 volts in the start position the system will not Tach Tachless learn Activate Self Learning Impact Sensor 1 Press the LOCK button on the remote 5 times in a row once every half second The siren will chirp 3 times and the park lights will come and stay on solid 2 While the park lights are on strike the vehicle at the desired level to trigger the alarm 3 The siren will respond with one chirp to confirm that the Shock Sensor is programmed Strike the vehicle 3 times to set the impact level
34. w the last shut down code The siren will chirp once to confirm code one If the siren does not chirp there are no codes in memory Step 4 The LED s on the antenna will flash a code corresponding to a shut down trigger Press the Program Button again to check the second code The siren will chirp twice to confirm code two Step 5 To Clear Diagnostic Memory While in Diagnostic Mode press and hold the Program Button for five seconds The park lights will flash and the siren will chirp once Note Once diagnostic memory has 4 improper shutdown events in memory the system will not record any further shutdown events until the system memory has been cleared INSTALLATION GUIDE TIRING DIAGRAM 27250 30amp Output Starter YELLOW 30amp Output Heater 30amp Input Power 30amp Input Power WHITE 30amp Output Jumper Selectable 30amp Output BLUE Ignition 1 Tau i Eg Tay 13 EE oon g 4 5 a ig 500ma Output SGRANGE Door Trigger GREEN gt Ground a O a Programmable Input This input is a optional connection for TL models This input is programmable and may need to be programmed for Tachless operation See Page 11 C gt r ee E gt rn 12v for Voltage Inverter Onl 500ma Output Door Unlock Output Note The center pin of this connector is low current and designed to power a Voltage Inverter Do not use the center pin of this c
Download Pdf Manuals
Related Search