Triarch CF-31120 User's Manual
Contents
1. MONA e p Motor Blade S ade Screw 2S Motor m 7 Blade Iron NY bo EL g oA Iu Ae Blade Medallion Top eo lt Oooo Cmm Washer Switch Housing Bulb Light Kit Bottom Glass Washer 5 amp Washer Nut moi TS Ca NA P Finial m Triarch International Inc Page 4 TAA51229062. CF 31120 52 Ceiling Fan AMBASSADOR FAN MODEL CF 31120 To Begin Weight 28 88 Lbs lp Check to make sure you have the following Required Helpful es YG SN iS a e 3 F LA electrical tape Phillips screwdriver A C Tester Light do it yourself guide i A lS Qo A Lge Loo pliers safety glasses tape measure wire cutters step ladder wire strippers Page 1 Preparation Important When using an existing outlet box be sure the box is securely attached to the building structure and can support the full weight of the fan Failure to do so can result in serious injury or death Turn off circuit Downrod Mounting breakers and wall switch to the fan supply line leads A Warning Failure to disconnect power supply prior to installation may result in serious injury or death Secure mounting bracket to electrical box Important If using the angle mount make sure t open end of mounting bracket is installed facing the roof Downrod Fan Mounting Check to make sure blades are at least 30 inches from any obstruction Check downrod length to ensure blades are at least 84 7 feet above the floor Helpful Hint Downrod style mounting is best suited for ceilings 8 feet high or higher For taller ceilings you may want to use an extension rod not included Angle style mounting is best suited for angled or vaulted ceilings A lon
3. ends together with pliers white to white black to black and blue to blue or black and blue to black and green to green ground Snip ends Screw on wire nuts in a clockwise direction Tape nuts and wires together A Warning Be sure no bare wire or wire strands are visible after making connection Place green and white connections on opposite side of box from the black and blue if applicable connections Lift canopy to hanger bracket Tighten all screws securely A Warning For downrod mounting be sure that the tab in the bracket rests in the slot of the ball end Remove the knob from switch housing Screw the light kit into the switch housing Install the bottom glass and secure it with washer nut cap and finial Position blade bracket so that it rests flush against blade Tighten all screws securely Install the light kit into the fan Clip on the pull chain Insert only one screw through blade bracket and partially tighten Insert 2nd screw tighten and then tighten 1st screw Hepeat with remaining blades Install three C26 40 watt bulbs included Remove the washer nut and finial from the light kit Page 3 Replacement Parts Keep this guide handy for ordering replacement parts Mounting Bracket g Downrod p c1 Lock Pin Lock Pin Clip Canopy o SS Cover of Collar e Light Kit E90 28 Bulb
4. ger extension rod will be needed to ensure proper blade clearance Hemove the screws on the lower level of the motor Install the top glass and motor cover on the motor Tighten all the screws to secure the cover Install three C26 40 watt bulbs included to the sockets Put on the light pan and connect wires Tighten the light pan on the motor and secure it with screws Slip the downrod Hang the fan in the over the wire mounting bracket sleeve align the Align the slot in the hole and reinstall ball with the tab on the pin and clip the bracket Firmly tighten t both downrod set screws Loosen all the screws on the upper level of the motor but remove only one Insert the downrod through the canopy and cover of collar with the ball toward the ceiling Feed wires from the fan motor through the downrod Page 2 Wiring A Important Make sure wiring box is properly grounded or that a ground green wire is present Note Black wire is hot power for fan Blue wire is hot power for light kit White wire is common for fan and light kit as neutral wires Green wire is ground A Warning If house wires are different colors than referred to above Stop immediately A professional electrician is recommended to determine wiring Connect green wire from downrod to green wire on mounting bracket Final Installation Strip 3 4 inches of insulation from wire ends Twist stripped
Download Pdf Manuals
Related Search