Triarch 31402-27 User's Manual
Contents
1. green Insulated wire other than with copper conductor green with silver conductor Notes When parallel wires SPTI amp SPTII are used The Neutral wire is square shaped or ridged and the other wire Will be round in shape or smooth see us Installation Instructions for Hanging System Ceiling Ceiling outlet box White supply wire Black supply wire Smooth side of wire w o marking Ribbod wire w o marking Screw Crossbar Canopy Bracket threaded screw Top finial nut Top finial loop Chain Fixture support loop2. 31402 27 A loop Q poly ball ER washer i S nut Tiron washer U pipe fixture arm nut secure diffuser flush pan j pipple nipple check ring glass washer nut glass glass washer nut bottom cap finial z2zCOzu Hron m g Assembly instruction for 31402 27 1 connect fixture arm B with flush pan C 2 Install fixture loop A to fixture B for pendant onty with poly ball Q washer R unt S iron washer T 3 Use the lock up nut P to connet with fixture B and loop A 4 Adjust arms to space evenly 5 Install light bulbs not provided 6 Secure glass I with center pipe U nipple D check ring F glass washer G nut H glass washer J nut H bottom cap L and finial M 7 Connect electrical wires at junction box and secure crossbar nipple and canopy loop READ amp SAVE THESE INSTRUCTIONS EEPL TREE NOTE Fixtures weighing over 25 Ibs must be supported independently of the outlet box 1 2 3 4 6 7 8 9 Rotate arms until in line with canter of fixture body Arms should tighten as they are turned if they do not tighten hex nut at top and bottom of arms Screw hex nut on to threaded pipe and screw threaded pipe into coupling on lop of fixture body Secure threaded pipe in place by lightening hex nut against coupling Slip top trim over threaded pipes and screw on loop T
3. urn off power Supply wires shall enter the outlet box through any knockout except the top center knockout Fixture is to be mounted by a steel pipe with 3 4 of 3 8 18 NPSN thread at bottom not supplied Position pipe so that approximately 1 2 of thread protrudes into outlet box Attach pipe to a structural or birding member of sufficient strength to support at least 4times the fixture weigh Thread pipe coupling onto protruding pipe inside outlet box Secure in place by tightening allen head screw Thread hex nut onto threaded pipe Screw threaded pipe into pipe coupling Secure in place by tightening hex nut against pipe coupling and tightening allen head screw Thread hex nut Slip on ground wire and thread a second hex nut onto threaded pipe 10 Connect screw collar loop without threaded ring to threaded pipe 11 Pass canopy over screw collar loop Approximately one half of the screw collar loop extensor thread should be exposed Adjust loop as required Remove canopy and lighten hex nut against screw collar loop Tighten second hex nut against first tohold ground wire in place 12 Attach chain to fixture not shown 13 Slip threaded ring then canopy onto chain 14 Attach chain With fixture connected to bottom of screw collar loop 15 Weave siscitical wire and ground wire up chain through screw collar loop 16 Connect fixture ground wire and ground wire attach to threaded pipe to outlet box ground wire
4. with wire concoctor notprovided Never connect ground wire to black or white power supply wires 17 Make wire connections connectors not provide Reference chart below for correct connections and wire accordingly 18 Raise canopy to ceiling 19 Secure canopy in place by screwing threaded ring onto screw collar loop Carefully slip glasses half plate inside arms and seat on lop of fixture plate allowing studs to pass through holes glass Secure in place with nylon washer and ball knob DO NOT over tighten Repeat for remaining glass half plate Lift ring up to fixture allowing threaded pipe and screw threaded pipe into coupling on bottom of fixture body Secure threaded pipe in place by tightening hex nut against coupling 22 Screw hex nut on to threaded pipe and screw threaded pipe into coupling on bottom of fixture body Secure threaded pipe in place by tightening hex nut against coupling Carefully lift glass up to ring and over threaded pipe into coupling on bottom of fixture body Secure threaded pipe in place by tightening hex nut against coupling 24 Slip trim over threaded pipe and screw on finial 20 21 w 23 lt Connect Black or Connect Red Supply Wire to White Supply Wire to Black White Parallel cord round amp smooth Parallel cord square amp ridged Clear Brown Gold or Clear Brown Gold or Black without tracer Black with tracer Insulated wire other than
Download Pdf Manuals
Related Search