Triarch 29645 User's Manual
Contents
1. washers as shown Rod should extend throungh outlet box a minimum of1 Tighten the two hex nuts above the wood support against each other to lock their position on the nipple Caution Do not tighten hex nuts at outlet box at this time Leave loose until entire fixture weight is suspended 5 Attach hex nut hickey and 2 3 8 nipple onto the end of supportrod 6 Connect screw collar loop onto the threaded nipple Pass canopy over screw collar loop for visual inspection Approximately one half of the screw collar loops exterior threads should be exposed Make necessary adjustments as required and remove canopy 7 Spread a chain link and attach to the fixture loop Slip threaded ring onto the other end of the chain then the canopy then attach chain to screw collar loop 8 Weave electrical wires and ground wire up chain and through the screw collar loop and into the outlet box ELECTRICAL CONNECTIONS 1 Cut off excess wire leaving 6 for electrical connections Split the wire into separate leads 2 Connect grounding wire green or bare copper from the supply circuit to the grounding wire on the fixture 3 Connect one half of the fixture cord to the white wire of the supply circuit Connect the other half of the fixture cord to the black wire of the supply circuit 4 CAUTION No loose strands or loose connections should be present Secure with UL approved wire connectors and electrical tape2. ASSEMBLY INSTRUCTIONS READ AND SAVE THESE INSTRUCTION UNPACK THE FIXTURE 1 2 3 TO PROTECT THE FINISH PLACE ALL PARTS ON A SOFT SURFACE PUT THE GLASS SHADE ONTO THE SOCKET SECURE IT BY SOCKET RING DETERMINE THE LENGTH OF CHAIN REQUIRED TO HANG THE DESIRED HEIGHT USINGPLIERS OPEN END LINK OF CHAIN AND ATTACH TO THE CHAIN LOOP ON TOP OF THE FIXTURE REMOVE OR ADD CHAIN AS DESIRED AT THIS TIME LACE FIXTURE WIRE AND GROUND WIRE UP THROUGH EVERY OTHER LINK OF CHAIN No 29674 29675 No 29742 29743 CEILING SUPPLY GROUND WIRE OUTLET BOX WHIT BLACK SUPPLY WIRE E SUPPLY WIRE WIRE CONNECTORS FIXTURE W ee 2 REQUIRED WHITE OR RIBBED FIXTURE WIRE 8 32 SCREWS SUPPLIED WITH BOX CROSS BAR NIPPLE FIXTURE GROUND WIRE GREEN GROUND SCREW SCREW COLLAR NUT SCREW COLLAR LOOP INSTALLATION INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS CAUTION TO AVOID POSSIBLE ELECTRIC SHOCK MAKE SURE THE ELECTRICITY 15 SHUT OFF AT THE MAIN PANEL IF YOU ARE REPLACING AN EXISTING FIXTURE FIRST TURN THE FIXTURE OFF NEXT TURN THE WALL SWITCH OFF FINALLY GO TO THE MAIN FUSE OR BREAKER BOX IN YOUR HOME TURN THE FUSE OR BREAKER TO THE OFF POSITION SOME TYPES OF FUSES MUST BE UNSCREWED TO SHUT OFF THE POWER ALL WIRING MUST BE DONE IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRIC CODES IF YOU ARE NOT FAMILIAR WITH WIRING YOU SHOULD USE A QUAL
3. IFIED ELECTRICIAN THIS FIXTURE IS INTENDED TO BE MOUNTED TO UL LISTED OUTLET BOX CAPABLE OF SUPPORTING THE FIXTURE 1 ATTACH THE CROSSBAR TO THE CEILING OUTLET BOX USING THE TWO SCREWS PROVIDED WITH THE OUTLET BOX NOTE IF THE SCREWS WITH OUTLET BOX ARE TOO SHORT USE THE 2 8 32 X 1 1 4 SCREWS PROVIDED IN THE MOUNTING HARDWARE PACKAGE NEXT SCREW THE SCREW COLLAR LOOP ONTO THE NIPPLE AND THEN SCREW THE NIPPLE INTO THE CROSS BAR 2 SLIDE THE SCREW COLLAR NUT AND THEN THE CANOPY ONTO THE END OF THE CHAIN THEN FASTEN THE END LINK OF CHAIN TO THE SCREW COLLAR LOOP 3 INSERT THE FIXTURE WIRE AND THE GROUND WIRE UP THROUGH THE NIPPLE ATTACH THE WHITE OR RIBBED FIXTURE WIRE TO THE WHITE SUPPLY WIRE IN THE OUTLET BOX USING THE TWIST ON WIRE CONNECTORS PROVIDED ATTACT THE BLACK OR SMOOTH FIXTURE WIRE TO THE BLACK SUPPLY WIRE IN THE SAME MANNER ATTACH THE FIXTURE AND SUPPLY GROUND WIRES ONTO THE CROSS BAR USING THE GREEN GROUND SCREW 4 TUCK THE WIRES CAREFULLY INSIDE THE OUTLET BOX NEXT RAISE THE CANOPY TO THE CEILING AND SECURE IN PLACE BY SCREWING THE SCREW COLLAR NUT ONTO THE SCREW COLLAR LOOP 5 INSTALL THE THREE GLASS SHADES AND SECURE WITH SOCKET RINGS INSTALL 60 WATT MAX BULBS NOT INCLUDED IN SOCKETS ATTACH TWO SURPPORT RODS FIRST HOOK ONE END OF A SUPPORT ROD ONTO AN S HOOK HOOK THE OTHER END ONTO A HANGER PLATE HOOK INSTALL THE SECOND SUPPORT ROD IN THE SAME MANNER PLACE GLASS BOWL INTO RING AS SHOWN INSTALL THIRD SU
4. PPORT ROD IN THE SAME MANNER AS THE FIRST TWO 6 RESTORE POWER YOUR NEW FIXTURE 15 NOW READY TO USE ASSEMBLY INSTALLATION Disconnect power at main fuse box before installing fixture to prevent possible injury from electrical shock Remove all parts and parts packages from carton Warning Fixtures weighing more than 50Ibs or more must be mounted directly to the building structure Avertissement Les accessoires qui p sent plus que 25 kilogrammes ou doit tre plus mont directement la structure de b timent STEEL WASHER i WOOD SUPPORT M ee 4 XISTING STRUCT 10 NIPPLE RUCTURI 17 STEEL WASHER 4 mm HEX NUT OUTLET BOX _ m WHITE HOUSE WIRE t L Z Z Z Z Z Z CEILING BLACK HOUSE WIRE WIRE CONNECTION FIXTURE WIRE FIXTURE WIRE HOUSE GROUND WIRE HICKEY FIXTURE GROUND WIRE 2 3 8 NIPPLE lt SCREW COLLAR RING VU sCREW COLLAR LOOP _ CHAIN LOOP 1 Remove center knockout in outlet box 2 Position wood support across ceiling joists over outlet box Locate and drill hole for the 3 8 nipple 3 After drilling hole align wood support over the outlet box and secure with nails 4 Install 10 long nipple through wood support and center hole in outlet box with hex nuts and
Download Pdf Manuals
Related Search