TP-Link TL-SF1048 V0 User Guide
Contents
1. TP LINK User Guide TL SF1016 TL SF1016DS TL SF1024 TL SF1024D TL SF1048 16 24 48 port 10 100Mbps Fast Ethernet Switch Rev 2 0 1 7106503501 COPYRIGHT amp TRADEMARKS Specifications are subject to change without notice TP LINK is a registered trademark of TP LINK TECHNOLOGIES CO LTD Other brands and product names are trademarks or registered trademarks of their respective holders No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation transformation or adaptation without permission from TP LINK TECHNOLOGIES CO LTD Copyright 2011 TP LINK TECHNOLOGIES CO LTD All rights reserved http www tp link com FCC STATEMENT HE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense This device complies with part 15 of the FCC Rules Operation i2. contents should be found in your box gt One TL SF1016 TL SF1016DS TL SF1024 TL SF1024D TL SF1048 Switch gt One power cord gt This User Guide gt Mounting screws and two L planks Make sure that the package contains the above items If any of the listed items are damaged or missing please contact with your distributor TL SF1016DS and TL SF1024D do not include mounting screws and two L planks Chapter1 Product Introduction This chapter describes the features of the model of TL SF1016 TL SF1016DS TL SF1024 TL SF1024D TL SF1048 16 24 48 port 10 100Mbps Fast Ethernet Switch TL SF1016 TL SF1024 and TL SF1048 just differ in the size the number of LED indicators and ports and all figures in this guide are of TL SF1016 1 1 Product Overview TL SF1016 TL SF1016DS TL SF1024 TL SF1024D TL SF1048 16 24 48 port Switch provides 16 24 48 10 100Mbps Auto Negotiation RJ45 ports Each port of the TL SF1016 TL SF1016DS TL SF1024 TL SF1024D TL SF1048 supports auto MDI MDI X function eliminating the need for crossover cables or Uplink ports The Switch is Plug and Play and any port can be simply plugged into a server a hub or a switch using straight cable or crossover cable The TL SF1016 TL SF1016DS TL SF1024 TL SF1024D TL SF1048 16 24 48 port 10 100Mbps Fast Ethernet Switch provides you with a low cost easy to use high performance seamless and standard upgrade to improve your old network to a 100Mbps network It wi
3. e equipment Use only the power cord provided with the Switch Make sure the voltage of the power supply meets the requirement of the input voltage of the Switch Do not push any objects into the openings of the Switch Ensure the vent hole is well ventilated and unblocked Do not open or remove the cover of the Switch 2 Location Requirements When you choose a location for the Switch please follow these guidelines Install the Switch on a flat and stable surface that can support the entire weight of the Switch with all fittings Locate the Switch far from strong electromagnetic field generators Such as motors vibration dust and direct exposure to sunlight To ensure adequate air flow around the Switch At least 10 cm 4 inches of space at the front and rear of the Switch is needed for ventilation Make sure that the Switch will be accessible and that the cables can be easily connected Position the Switch away from water and moisture sources be sure to provide an acceptable temperature and humidity operating environment 3 2 Installation This Switch can be either installed on the standard 19 inch mountable rack or located on the desktop 3 2 1 Desktop Installation To install the Switch on the desktop please follow the steps 1 Set the Switch on a flat surface strong enough to support the entire weight of the Switch with all fittings 2 Remove the adhesive backing papers from the rubber feet 3 Tur
4. ll boost your network performance up to full duplex data transfer 1 2 Features Complies with IEEE802 3 IEEE802 3u standards 16 24 48 10 100Mbps Auto Negotiation RJ45 ports supporting Auto MDI MDIX gt Supports IEEE802 3X flow control for full duplex mode and backpressure for half duplex mode LED indicators for monitoring power link activity speed Rack mountable steel case Internal power supply Chapter 2 Identifying External Components This Chapter describes the front panel rear panel and LED indicators of the Switch 2 1 Front Panel The front panel of TL SF1016 consists of switch model switch LED indicators and 16 10 100Mbps RJ 45 ports TP LINK TL SF1016 hernet Switch Figure 2 1 TL SF1016 Switch Front Panel sketch The LED indicators include Power Link Act LED indicators which are used for monitoring and pre troubleshooting of the Switch The following section shows the LED indicators of the Switch along with an explanation of each indicator gt Power LED This indicator will light solid red when the Switch powers up If the LED is not lit please check the power supply and connection gt Link Act LED The LED indicates Link Active status The corresponding LED indicator will light solid green when connected to a network device lt flashes green when data is being transmitted or received on the working connection gt 100Mbps The corresponding port LED indicator wi
5. ll light solid green when its working on 100Mbps speed Not lit indicates working on 10Mbps speed Because of the difference among the mode of switch some switches don t include the 100Mbps indicator such as TL SF1048 TL SF1016DS TL SF1024D and a 2 2 Rear Panel The rear panel of TL SF1016 features a power socket and a Grounding Terminal marked with Figure 2 2 TL SF1016 Switch Rear Panel sketch gt Grounding Terminal TL SF1016 already comes with Lightning Protection Mechanism You can also ground the Switch through the PE Protecting Earth cable of AC cord or with Ground Cable For detail information please refer to section 3 3 Connect to Ground gt AC Power Socket Connect the female connector of the power cord here and the male connector to the AC power outlet Please make sure the voltage of the power supply meets the requirement of the input voltage Because of the difference among the mode of switch some switches don t include the Grounding Terminal such as TL SF1048 and a few of TL SF1016 and TL Chapter 3 Installation 3 1 Precautions To ensure a long term and stable performance of the Switch please pay attention to the following before the installation 1 Safety Requirements Before cleaning the Switch cut off the power supply Do not clean it by the waterish cloth and never use any other liquid cleaning method Take waterproof measures during storage transportation and operation of th
6. nect the Switch to the ground in two ways connecting to the Grounding Bar or connecting to the Ground via the power cord Please connect the Switch to ground in the optimum way according to your specific operation environment e Connecting to the Grounding Bar If the Switch is installed in the Equipment Room where a Grounding Bar is available you are recommended to connect the Switch to the Grounding Bar as shown in the following figure 1 Switch Rear Panel Grounding Terminal 3 Ground Cable 4 Grounding Bar Figure 3 4 e Connecting to the Ground via the power supply If the Switch is installed in the normal environment the Switch can be grounded via the PE Protecting Earth cable of the AC power supply as shown in the following figure 1 Switch Rear Panel 2 AC Power Cord with PE cable Figure 3 5 The figure is to illustrate the application and principle The power plug you get from the package and the socket in your situation will comply with the regulation in your country so they may differ from the figure above If you intend to connect the Switch to the ground via the PE Protecting Earth cable of AC power cord please make sure the PE Protecting Earth cable in the electrical outlet is well grounded in advance 3 4 Power on The TL SF1016 TL SF1016DS TL SF1024 TL SF1024D TL SF1048 16 24 48 port 10 100Mbps Fast Ethernet Switch is powered by an AC Power Supply Connect the Switch and powe
7. nover the Switch and attach the supplied rubber feet to the recessed areas on the bottom at each corner of the Switch Figure 3 1 Attaching Rubber Feet 4 Upturn the Switch and connect it to the network devices while keep enough ventilation space around 5 Connect the Switch to power source with the provided power cord 42 Caution Please avoid any heavy thing placed on the Switch 3 2 2 Rack Installation To install the Switch in an EIA standard sized 19 inch rack follow the instructions described below 1 Secure the supplied rack mounting brackets to each side of the Switch with supplied screws as illustrated in the following figure Figure 3 2 Attaching Brackets 2 After the brackets are attached to the Switch use suitable screws not provided to secure the brackets to the rack as illustrated in the following figure 2 l vi WA Z Z u p l j Z l l 2 O O O O O O O w Ja O O O O O O O O O O Figure 3 3 Mounting Switch 3 Connect the Switch to network devices 4 Supply power to the Switch with the provided power cord 3 3 Connect to Ground Connecting the Switch to ground is to quickly release the lightning over voltage and over current of the Switch which is also a necessary measure to protect the body from electric shock In different environments the Switch may be grounded differently The following will instruct you to con
8. r outlet by power cord Powering on the Switch it will be automatically initialized and the LED indicators should respond as follows 1 All of the LED indicators will flash momentarily for one second which represents a resetting of the system 2 The Power LED indicator will light up Appendix A Specifications General Standards IEEE802 3 10Base T IEEE802 3u 100Base TX Protocol CSMA CD Ethernet 10Mbps Half Duplex 20Mbps FullDuplex Fast Ethernet 100Mbps Half Duplex 200Mbps Full Duplex 10Base T UTP category 3 4 5 cable maximum 100m Network Media EIA TIA 568 100 STP maximum 100m Cable Data Transfer Rate 100Base TX UTP category 5 5e cable maximum 100m EIA TIA 568 100 STP maximum 100m in OGIGse Automatically learning automatically agin Learning L dl l 10Base T 14881pps Port Frame Filter Rate 100Base Tx 148810pps Port Frame Forward 10Base T 14881pps Port Rate 100Base Tx 148810pps Port Environmental and Physical 10 90 non condensing 5 90 non condensing Appendix B Troubleshooting 1 The Power LED is not lit gt Make sure the AC power cord connected the Switch with power source properly gt Make sure the power source is ON 2 The Link Act LED is not lit when a device is connected to the corresponding port gt Make sure that the cable connectors are firmly plugged into the Switch and the device gt Make sure the connected device is turned on and working
9. s subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment CE Mark Warning CE This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures As for TL SF1016DS TL SF1016 TL SF1024D and TL SF1024 a fuse resistor is used in the F1 position on the PCB of the power module The fuse resistor should be used with the following type 10ohm 2W 25 C CONTENTS Package Contents ds Chapter 1 Product IntroductiON occcoccccnnnccccnniccnnconcnnoncnconcnrnnnannnnnarenannnnanos 1 1 Produc FOVEO W ii a a a uk ance ne ng ea 1 2 A L a eat N a eeaen O Chapter 2 Identifying External Components sseennnnnnnnnnnznnnenzanennnzanmnnzzn 2 1 Front Panels d tasa 2 2 Rea Paella daa c Chapters Installation 2 add 3 1 Procardia 3 2 Nal OMT CS ET E A EOE 3 2 1 Desktop installation 3 2 2 Rack Iristalla tie ie e e Ra 3 3 Connechio GOMMA ir A A 3 4 POW Oreste A see Appendix A Specifications ui Appendix B Troubleshooting ccocccocncoccncocnconaconcnnnnnnonanonanenanonanonanrennrenarenaanon Package Contents The following
10. well gt The cable must be less than 100 meters long 328 feet TP LINK TP LINK TECHNOLOGIES CO LTD http www tp link com
Download Pdf Manuals
Related Search