TP-Link TL-POE150S V3 User Guide
Contents
1. cause serious damage to your network device gt If you want to know more details about TL POE10R Splitter please refer to TL POE10R User Guide on our website http www tp link com Appendix Specifications Normal IEEE 802 3 IEEE 802 3u IEEE 802 3ab IEEE 802 3af 1 10 100 1000Mbps Auto Negotiation RJ45 LAN port Ports 1 10 100 1000Mbps Auto Negotiation RJ45 PoE port 1 48V DC Power Input Port Standards Cabling Type RJ45 CAT5 UTP cable LED PWR Safety amp FCC CE Emissions i Environmental and Physical Operating Temp 0 C 40 C 32 F 104 F Storage Temp 40 C 70 C 40 F 158 F Operating Humidity 10 90 RH Non condensing Storage Humidity 5 90 RH Non condensing Dimensions W D H 80 8 54 24 mm2. receiving antenna gt Increase the separation between the equipment and receiver gt Connect the equipment into an outlet on a circuit different from that to which the receiver is connected gt Consult the dealer or an experienced radio TV technician for help This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment CE Mark Warning CE This is a class B product In a domestic environment this product mav cause radio interference in which case the user may be required to take adequate measures NJ IIponykT cepTH IKOBAHO 3riqHo C npaBujaMu cucremu YkpCEIIPO Ha BIJINOBIJIHICTE BUMOTAM HOpMATHBHHX JJOKVMEHTIB Ta BHMOFAM mo TlepeqOaueHi UMHHHMH 34KOHOJIABUHMH AKTAMH YKpaiHH SAFETV NOTICES gt Do not use this product near water for example in a wet basement or near a swimming pool v Avoid using this product during an electrical storm There may be a remote risk of electric shock from lightning CONTENTS Package Contents isisisi naa asks Chapter 1 Introduction 1 Overview of the Product 2 Features 1 1 Overview of the Product seen
3. 1 Chapter 2 Identifying External Components Chapter 3 Connecting the PoE Injector mn Appendix Specifications Package Contents The following items should be found in your package gt TL POE150S PoE Injector gt One Power Adapter gt One Ethernet CAT5 UTP Cable gt This User Guide amp Note Make sure that the package contains the above items If any of the listed items are damaged or missing please contact your distributor Chapter 1 Introduction 1 1 Overview of the Product Thank you for choosing the TL POE150S PoE Injector The Power over Ethernet PoE Injector is able to supply steady power to Powered Device PD or PoE Splitter over the Ethernet cable The Ethernet equipment can work as a Power Sourcing Equipment PSE with the help of the TL POE150S connection PoE technology allows the existing Ethernet infrastructure to transmit electrical power along with data to remote IP endpoints over the Ethernet cables which can greatly save the cost of the external power cables Your network can benefit from PoE technology for it will ensure the normal working status of your network while keep the existing Ethernet infrastructure secure PoE This technology describes a system to transmit electrical power along with data to remote devices over standard twisted pair cable in an Ethernet network PD A device powered by a PSE and thus consumes energy Examples inc
4. TP LINK User Guide TL POE150S PoE Injector 7106503937 COPYRIGHT amp TRADEMARKS Specifications are subject to change without notice TP LINK is a registered trademark of TP LINK TECHNOLOGIES CO LTD Other brands and product names are trademarks or registered trademarks of their respective holders No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation transformation or adaptation without permission from TP LINK TECHNOLOGIES CO LTD Copyright 2012 TP LINK TECHNOLOGIES CO LTD All rights reserved http www tp link com FCC STATEMENT FC This equipment has been tested and found to complv with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequencv energv and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures gt Reorient or relocate the
5. lude powering IP telephones wireless LAN access points network cameras network hubs embedded computers etc PSE A device switch or hub for instance that will provide power in a PoE setup 1 2 Features gt Complies with IEEE 802 3 IEEE 802 3u IEEE 802 3ab IEEE 802 3af standards gt Compatible with PoE compliant PDs and PoE Splitters gt Transmits electrical power along with data in one single cable gt External 48V DC power supply gt Supports Plug and Play for the devices without any configuration gt Elegant appearance with space saving mini size Chapter 2 Identifying External Components m POWER DATA OUT POWER DATA OUT Connect to the PD or PoE Splitter with a CAT5 UTP cable LAN IN Connect to a DC 48V Connect to the network device such as a provided power adapter Switch or Router with which can supply steady CAT5 UTP cable power of 48V DC LAN IN PWR DC 48V PWR Power LED A steady blend color of red and yellow indicates that the power adapter is working properly A steady green light indicates that the PoE system has detected the PD or PoE Splitter and the PoE Injector is supplying power normally A flashing light indicates abnormal power supply Chapter 3 Connecting the PoE Injector You can use TL POE150S PoE Injector with PD or PoE Splitter to expand your network to where there are no power lines or outlets where you wish to fix devices such as AP
6. s IP Cameras or IP Phones etc The following steps will tell you how to connect the PoE Injector correctly 1 2 Use a CAT5 UTP cable to connect port of Ethernet device such as a switch hub or router to the LAN IN port Please connect the power adapter properly to a power socket with provided power cable and then connect the other end of the power adapter to the DC 48V port of the TL POE150S Connect the POWER DATA OUT port of the TL POE150S to a PD or a PoE Splitter with CAT 5 UTP cable Now the device can work normally with data and power There are two schemes to realize the PoE 1 If the device supports PoE take an IP camera with PoE for example following topology will work 7 CATS UTP Cable Power amp Data IP Camera with POE TL POE150S Power Adapter CAT5 UTP Cable Data Switch Scheme 1 2 If the device does not support PoE it is necessary to have a PoE Splitter to separate the power and data transmitting them detached in one UTP cable and one power cable Here we take TP LINK TL POE10R Splitter for example You can use following topology Switch CATS UTP Cable Power amp Data L TL POE1508 JIL EOEJOR lt Pe LG NN CAT5 UTP Cable Data Power Cable CATS UTP Cable Wireless AP Data Scheme 2 amp Note gt Do not mistake the power port of the TL POE150S and TL POE10R when choosing the Scheme 2 or else it will
Download Pdf Manuals
Related Search