Torker Bicycle CX User's Manual
Contents
1. pedal to R crank Tighten se curely w a 15mm wrench This is also a good time to check the F Place seatclamp crank arms and tighten them Ver unistar fork if necessary bolts to attach Bearing Caps 3 Slide seatclamp on top of fork F Apply a thin film of grease to the seatpost and insert it into the fork G Using the 5mm allen wrench tighten the seatpost clamp so that the seatpost does not twist in the fork H Also check that the bolts holding the seat onto the post are secure as well as the bolts on the handle 4 Make sure the tire bead is D1 Left pedal seated evenly on the rim tightens counter Inflate the tire to the recom ray clockwise mended pressure thatis printed py Tighten on the sidewall of the tire seatclamp PARTS Your TX Unicycle Box should include all of the parts listed on the DX LX and CX as well as these additional pieces TOOLS You will need the same 7 tools listed on the previous page cum Adustes tO assemble your Unistar TX Wheel w 28t gear amp tire ASSEMBLING YOUR TX UNISTAR 1 Determine the front back right and left of the unicycle The sprocket is on the right 2 Take the axle nuts off the wheel and install the Chain Ad i justers A Then thread the axle y Tighten chain bolts back on adjusters to pull 3 Slide the wheel into the drop chain tight Be ts 1 ly B and set Chain sure to keep wheel a ee centered below A Att2. if you are new to unicycle riding Make sure all parts are tight and adjusted properly and A f that the tire is inflated to the recommended pressure NEVER gt ride any unicycle if any parts seem loose cracked broken or out of adjustment And when riding please avoid traffic and busy areas Never ride beyond your ability Take responsibility for your actions You are encouraged to ask your local bicycle retailer about unicycling There are also a number of unicycle related resources available on the Internet including clubs and instructional materials Saddle w Post TOOLS You will need Seatclam Beall A these tools to Caps ee assemble your Cl Se Hare Unistar Sey x Note 10mm peas wa Wheel w Cra wrench not i gma ded for S Your Unicycle Box endwrench NEeae y CX LX or DX should include all of these parts ASSEMBLING YOUR CX DX amp LX UNISTAR 1 Determine the front back right and left of the unicycle and the wheel Set the wheel into T R the bearing cradles Place the A Place Wheel in bearing caps A in place and 3 Bearing Cradle tighten the bolts to 45 inch AV and place on Caps pounds B Do not over tighten C Spin the wheel and check ape ae pe pa dates the spokes Adjust if needed ieee ocr ad 2 Apply a small amount of grease to the pedal threads Thread the pedals into their cor responding crank arms D1 L pedal to L crank D2 R
3. Thank you for buying a TORKER unicycle With proper setup and care your new Unistar will provide years of fun and entertainment Please read this manual thoroughly and save it for future reference If you have any doubts about your ability to assemble or adjust your uni cycle please contact your local bicycle dealer for assistance THINGS TO KNOW BEFORE ASSEMBLY Unicycles have a front back left and right It is important to know this to en sure that the saddle and pedals are installed correctly The fork is slotted where the seat post is inserted This slot is on the back The UNISTAR decal on the tube is on the front Align the saddle so that the narrow end or the handle depending on the model is pointed forwards Make sure the seat post is tight in the fork as this is crucial in controlling and steering your unicycle Cranks and pedals are marked left and right with a L and R stamped in to them Make sure the cranks are on the appropriate sides The pedals can only be installed in their respective cranks arms The right pedal tightens clockwise and the left pedal tightens E counter clockwise R RIGHT L LEFT The pedals must be tight in the cranks This helps to prevent the pedals from loosening during riding R RIGHT L LEFT THINGS TO KNOW BEFORE RIDING Always wear a helmet when riding your unicycle We also recommend knee pads elbow pads and wrist guards especially
4. ach chain adjusters to axle adjusters on to fork dropouts C Do not fully tighten yet 4 Place the chain around both sprockets 5 Now tighten up the chain ad justers on each side using the 10mm wrench Be sure to keep the wheel centered inside fork NOTE Check chain tension Chain may deflect 1 2 when squeezed firmly 7 Now firmly tighten axle nuts 8 Apply a small amount of grease to the pedal threads Thread the pedals into their corresponding crank arms D 1 L pedal to otic nites heat L crank D 2 R pedal to R attach correct crank Tighten securely w a pedals on to 15mm wrench correct cranks 9 Slide QR seatclamp on top of eae directions for fork K Apply a thin film of specifics grease to the seatpost and insert seatpost saddle into the fork G Tighten the seatpost clamp with your hand so that the seatpost does not twist in the fork and lock in 10 Make sure the tire bead is ae N AT seated evenly on the rim Inflate K Slide on seat the tire to the recommended clamp insert seat pressure that is printed on the post and tighten sidewall of the tire F 2y C Set Chain Adjusters in to dropouts like so A E Put chain on UNICYCLE ASSEMBLY INSTRUCTION MANUAL Lx 0w w cy TorkerUSA com TORKER BICYCLES Seattle Bike Supply 7620 So 192nd Kent WA 98032 Have a question E mail info torkerusa com
Download Pdf Manuals
Related Search