Timex T301 User's Manual
Contents
1. Il il il l Off Reset Button Buzzer Alarm Button Radio Preset Buttons B Memory Set Button 89 4D9 Sleep Volume Button D Time Zone Button 77 8 Volume Thumbwheel Controls and Indicators Sleep Volume Indicator AM FM Radio Indicator Calendar Mode Preset Station Numbers Auto Set Time Zone Battery Low Indicator PM Clock Indicator Clock Radio Frequency Display Buzzer Alarm Radio Alarm Indicator RADIO BUZZER Indicator EVERYDAY 4 MON FRI 4 SAT SUN Daylight Saving 7 5 2 Alarm Indicators Time Indicator LCD Display With Indicators Auto Set and Manual Time and Date Settings Auto Set Time and Date Settings This model is equipped with the Auto Set feature meaning that the time and date settings have been programmed at the factory and will already be set when you first plug the model in Auto Set will automatically adjust the time and date settings for daylight saving time and leap years Auto Set is programmed for Eastern Standard Time if you do not live in this time zone you can easily switch the setting to one of six other time zones 1 To change your time zone setting press the Time Zone Button The current Auto Set Time Zone in the upper right hand corner of the display will flash for approximately ten seconds after which the display will revert to the standard clock display 2 While the Auto Set Time Zone is flashing2. batteries alkaline is recommended for 47 longer life while making sure that the and ends match up with those inside the battery compartment 3 Slide the battery compartment door back on making sure the door locks into place and gently return the unit to its upright position Battery Compartment Maintenance 1 Place the unit on a level surface away from direct sunlight or sources of excessive heat 2 Protect your furniture when placing the unit on natural wood or wood with a lacquered finish A cloth or other protective material should be placed between the unit and the furniture 3 Clean the casing with a soft cloth moistened only with mild soap and water Stronger cleaning agents such as thinner or similar materials are not recommended as they may damage the surface of the case 4 f the unit is not to be used for a prolonged period such as a month or longer remove the batteries to prevent possible corrosion Should the battery compartment become corroded or dirty clean the compartment thoroughly and replace the batteries Controls and Indicators On Sleep Button Radio Alarm Button Snooze Night Light Button RADIO on ot Chet BUZZER EVERYDAY 4 MON FRI 4 SAT SUN E m MEMSET I p SLEEP VOL 3 n n n E 3 h
3. on a bed sofa rug or similar surface that may block ventilation openings Also it should not be placed in a built in installation Such as a bookcase or cabinet that may impede the flow of air through the ventilation openings Heat The unit should be situated away from heat sources such as radiators heat registers Stoves or other appliances including amplifiers that produce heat Power Sources The unit should be connected to a g De SDN only of the type described in the operating instructions or as marked on the appliance itself Grounding or Polarization This product is equipped with a polarized alternating current line plug a plug having one blade wider than the other As a safety feature this plug will fit into the power outlet only one way If you are unable to fit the plug into the outlet try reversing the plug If the plug still fails to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of your polarized plug by forcing the plug into the outlet Power Cord Protection Power upay cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them Itis always best to have a clear area from where the cord exits the unit to where it is plugged into an AC outlet Cleaning The unit should be cleaned only as recommended See the Maintenance section of this manual for cleaning instructions Objects and Liquid Entry Care should be taken
4. press the Tuning Set Buttons to select your time zone The display will show each zone s current time setting There are seven time zones to choose from Auto Set Time Zones Z 01 Atlantic Standard Time Z 02 Eastern Standard Time Z 03 Central Standard Time Z 04 Mountain Standard Time Z 05 Pacific Standard Time Z 06 Alaskan Standard Time Z 07 Hawaiian Standard Time 3 When you have reached your time zone press the Time Zone Button to lock the setting into place Manual Time and Date Settings 1 To change your time setting press the Time Set Button so that the clock display begins flashing 2 While the display is flashing press the Tuning Set Buttons to set the time Hold a button for a few seconds to advance the time rapidly Be sure to set the correct AM PM time as shown by the PM Indicator 3 When you have set the current time press the Time Set Button again to return to the standard display 4 To change your date setting press the Q Date 7 5 2 Button The display will show the calendar setting 5 The display will show the flashing year Press the Tuning Set Buttons to set the current year When you have selected the year press the Q Date 7 5 2 Button again and follow the above instructions to set the month and then the day 6 After you have set the date press the Q Date 7 5 2 Butto
5. so that objects do not fall and liquids are not spilled into any openings or vents located on the product Attachments Do not use attachments not recommended by the product manufacturer Lightning and Power Surge Protection Unplug the unit from the wall outlet during a lightning storm or when it is left unattended and unused for long periods of time This will prevent damage to the product due to lightning and power line surges Overloading Do not overload wall outlets extension cords or integral convenience receptacles as this can result in fire or electric shock Damage Requiring Service The unit should be serviced by qualified service personnel when A the power supply cord or plug has been damaged B objects have fallen into or liquid has been spilled into the enclosure C theunit has been exposed to rain D theunit has been dropped or the enclosure damaged E theunit exhibits a marked change in performance or does not operate normally Antenna Do not connect an external antenna to the unit Periods of Nonuse If the unit is to be left unused for an extended period of time such as a month or longer the power cord should be unplugged from the unit to prevent damage or corrosion Servicing The user should not attempt to service the unit beyond those methods described in the user s operating instructions Service methods not covered in the operating instructions should be referred to qualified se
6. Model T301 Auto Set Dual Alarm Digital Clock Radio TIMEX TIMEX o p gd ALARM SET RADIO BUZZER gt E w ES FE EE L j TUN CLOCK PRESET 1 3 NA Ww BEL L di o CD c i _ sTIMESET MEMSET E q L 3 em a H AM FM SLEEP VOL RADIO BUZZER EVERYDAY 4 MON FRI SAT SUN For additional information online registration and exclusive special offers please visit our website www timexaudio com CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK OF UNIT NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE The lightning flash with arrowhead in an equilateral triangle is intended to alert the user of the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance Th
7. Set Buttons to find a station to listen to To scan the radio stations hold a button for about three seconds The radio will rapidly advance to the next strong signal 4 You may also use the Radio Preset Buttons to select a preset radio station See the Programming Radio Station Memories section for instructions on programming radio station settings 5 Rotate the Volume Thumbwheel to adjust the volume level 6 Press the amp Off Reset Button to turn the power off Programming Radio Station Settings This Alarm Clock Radio features a total of 18 programmable radio station settings 12 FM stations and six AM stations These allow you to preset your favorite stations and access them quickly 1 Press the On Sleep Button once to turn the radio on Note f the Q On Sleep Button is pressed more than once the unit will enter the sleep mode See the Sleeping to Radio with Timer section for more information about this feature 2 Press the AM FM Button to select a radio band The AM FM Radio Indicator will show which band is in use 3 Press the Tuning Set Buttons to find a station to program into the memory To scan the radio stations hold a button for about three seconds The radio will rapidly advance to the next strong signal 4 When you have reached the station you wish to program press the 9 Memory Set Button once while the station is displayed A station can only be programmed while its call number appears on the displ
8. TE This warranty is valid only if the product is used for the purpose for which it was designed It does not cover i products which have been damaged by negligence misuse or accident or which have been modified or repaired by unauthorized persons ii cracked or broken cabinets or units damaged by excessive heat iii damage to CD s or tape cassettes if applicable iv the cost of shipping this product to the Factory Service Center and its return to the owner This warranty is valid only in the United States of America and does not extend to owners of the product subsequent to the original purchaser Any applicable implied warranties are also limited to 90 days and SDI Technologies will not be liable for consequential damages Some states do not allow limitations on implied warranties or exclusion of consequential damages so these restrictions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state For questions or comments regarding this or other products please call our toll free number 1 800 888 4491 TIMEX is a registered trademark of Timex Corporation in the U S and other countries T301 051802 05 Printed in China
9. ay The Preset Station Number in the upper right hand corner of the display will flash for approximately ten seconds after which the display will revert to the standard clock display Instructions continued on following page 10 Listening to the Radio Continued Programming Radio Station Settings Continued 5 While the Preset Station Number is flashing press the Radio Preset Buttons until the display shows the slot number you wish to store the station as There are 12 FM and six AM slots to choose from Press the Memory Set Button again to save the setting The station can now be accessed using the Tuning Set Buttons as described in the Listening to the Radio section of the instructions Follow the above instructions to continue programming station settings into memory To edit a setting enter a different station as an existing Preset Station Number This overrides the original Sleeping to Radio With Timer Note For more information about playing the radio see the Listening to the Radio section of this manual 1 2 5 6 Press the On Sleep Button twice to enter the sleep mode Continue pressing the On Sleep Button to select a 90 60 30 or 15 minute sleep time When the display shows the desired sleep time stop pressing the button The sleep timer setting remains active for approximately ten seconds before returning to the standard clock display The Sleep Indicator will appear showing that the
10. e store where it was originally purchased Should this fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period SDI Technologies will repair or at its discretion replace this product without charge except for a 5 00 charge for handling packing return UPS postage and insurance This decision is subject to verification of the defect or malfunction upon delivery of this product to the Factory Service Center listed below The product must include proof of purchase including date of purchase The fee for service after the warranty period or without proof of purchase is 10 00 Before returning this product for service please first replace the batteries if applicable with fresh ones as exhausted or defective batteries are the most common cause of problems encountered If service is still required 1 Remove the batteries if applicable and pack the unit in a well padded heavy corrugated box 2 Enclose a photocopy of your sales receipt credit card statement or other proof of the date of purchase if within the warranty period 3 Enclose a check or money order payable to the order of SDI Technologies for the sum of 5 00 10 00 after warranty period 4 Send the unit prepaid and insured to the Factory Service Center listed below Consumer Repair Department SDI Technologies Inc Timex Audio Products Division 1401 Pullman Drive Suite A El Paso TX 79936 7726 NO
11. e symbols above are located at the bottom of the cabinet CAUTION To prevent electric shock do not use this polarized plug with an extension cord receptacle or other outlets unless the blades can be fully inserted to prevent blade exposure ATTENTION Pour pr venir les chocs lectriques ne pas utiliser cette fiche polaris e avec un prolongateur Une prise de courant ou une autre sortie de courant sauf si les lames peuvent tre ins r es a fond sans en laisser aucune partie a decouvert This device complies with part 15 of the Federal Communications Commission Rules Operation is subject to the condition that this device does not cause harmful interference A Consumer Guide to Product Safety When used in the directed manner this unit has been designed and manufactured to ensure your ersonal safety However improper use can result in potential electrical shock or fire hazards lease read all safety and operating instructions carefully before installation and use and keep these instructions handy for future reference Take special note of all warnings listed in these instructions and on the unit 1 2 Water and Moisture The unit should not be used near water For example near a bathtub washbowl kitchen sink laundry tub swimming pool or in a wet basement Ventilation The unit should be situated so that its location or position does not interfere with its proper ventilation For example it should not be situated
12. he alarm will sound at the set time and days 3 When the alarm sounds press the Off Reset Button to turn off the alarm while still maintaining the programmed 7 5 2 alarm settings To turn off an alarm and cancel its 7 5 2 settings press its Alarm Button so that its Alarm Indicator no longer appears on the display 4 To activate the snooze feature press the Snooze Night Light Bar when the alarm sounds The alarm will shut off for approximately nine minutes before sounding again The feature can be repeated several times during the one hour snooze cycle 5 If itis not turned off the alarm will sound for an hour before stopping As long as an Alarm Indicator appears on the display the alarm will sound at the set time according to the 7 5 2 settings Adjusting the Display Backlight e This alarm clock radio features an adjustable display backlight with dim medium and bright settings To select a backlight setting press the Snooze Night Light Bar until the desired brightness is reached Listening to the Radio Operating the Radio 1 Press the On Sleep Button once to turn the radio on Note If the Q On Sleep Button is pressed more than once the unit will enter the sleep mode with the radio operating on a timer See Sleeping to Radio with Timer for more information about this feature 2 Press the AM FM Button to select a radio band The AM FM Radio Indicator will show which frequency is in use 3 Press the Tuning
13. n again to return to the standard display Operating the Dual Alarm System This clock radio features a dual alarm system with two separate alarms that can be operated independently The alarms can be set to wake two people at different times or to have a main alarm and a backup One alarm features your choice of radio stations as an alarm wake sound while the second features a buzzer wake sound You can set the radio alarm the buzzer alarm or both alarms Setting Radio Alarm a Press the Alarm Set Button The display will flash and the Radio Alarm Indicator will appear If you do not begin setting the time within ten seconds of pressing the Alarm Set Button the display will stop flashing and you will need to press the Alarm Set Button again While the display flashes press the Tuning Set Buttons to set the wake time Hold a button for a few seconds to advance the time rapidly Be sure to set the correct AM PM time as shown by the PM Indicator After setting the radio alarm time you will need to select the station to wake up to First press the AM FM Button to select a radio frequency Next select a station using the Radio Preset Buttons For more information on programming radio stations into memory see the Programming Radio Station Settings section of this manual Rotate the 9 Volume Thumbwheel to set a wake sound volume level After setting the radio alarm wake time and sound you will need to select your 7 5 2 setti
14. ng The 7 5 2 setting lets you set the alarm for a full week weekdays only or the weekend Before setting the alarm be sure that the correct date is set as shown in the Auto Set and Manual Time and Date Settings section of the manual While the display is still flashing press the Date 7 5 2 Button until the desired setting is shown After you have set the radio alarm wake time wake sound and 7 5 2 setting press the Alarm Set Button twice so that the display shows the standard non flashing display Setting Buzzer Alarm 1 2 3 Press the Alarm Set Button twice The display will flash and the Buzzer Alarm Indicator will appear While the display flashes press the Tuning Set Buttons to set the wake time as described above After setting the buzzer wake time use the Q Date 7 5 2 Button to select the buzzer 1 5 2 setting as described above After you have set the buzzer wake time and 7 5 2 setting press the Alarm Set Button once so that the display shows the standard non flashing display Operating the Dual Alarm System Continued Activating the Alarms 1 To activate the radio alarm press the Radio Alarm Button so that the Radio Alarm Indicator appears on the display As long as this indicator appears the alarm will sound at the set time and days 2 To activate the buzzer alarm press the Buzzer Alarm Button so that the Buzzer Alarm Indicator appears on the display As long as this indicator appears t
15. radio timer has been activated Select a radio station using the AM FM Radio Button and the Tuning Set Buttons Press the 9 Sleep Volume Button to adjust the sleep volume to a comfortable level without affecting the alarm volume The Sleep Volume Indicator will show the current sleep volume level Turning the 9 Volume Thumbwheel will also adjust the sleep volume The radio will play for the programmed sleep time and then shut off To check how much sleep time is remaining press the On Sleep Button once To turn off the radio before the sleep time has elapsed press the Off Reset Button Antenna Information and Adjustment FM Extend the FM wire antenna to its full length and vary the direction to its strongest signal AM The AM bar antenna is located inside the cabinet Rotate the unit until you find the strongest AM signal Last Station Memory The tuner always remembers the last station selected before the radio was switched off and automatically selects the station again when the radio is turned on 11 Limited 90 Day Warranty Information Timex Audio Products a division of SDI Technologies Inc hereafter referred to as SDI Technologies warrants this product to be free from defects in workmanship and materials under normal use and conditions for a period of 90 days from the date of original purchase Should this product fail to function in a satisfactory manner it is best to first return it to th
16. rvice personnel For questions or comments regarding this or other products please call our toll free number 1 800 888 4491 3 Installation and Maintenance Installation 1 Remove unit and all packing materials from the carton You should save packing materials in case unit needs to be returned for service If you do not wish to save the materials please dispose of them properly 2 Place the unit on a stable level surface close to an AC outlet out of direct sunlight and away from sources of dust dirt heat water moisture vibration or magnetic fields 3 After installing the batteries see below and reading the Maintenance notes plug the AC cord into an outlet Sure Alarm Battery Backup Installation It is strongly recommended that 2 AA batteries be installed into the unit as directed below in order to activate this product s Sure Alarm Battery Backup feature The model should come with two batteries already installed In the event that the AC power cord is disconnected or a power failure or other interruption occurs the Sure Alarm Battery Backup will maintain clock and alarm settings for the life of the battery ensuring that the alarm buzzer only will sound at the set time During any interruptions the time and alarm settings will be saved and automatically restored when AC power is again active 1 Gently turn the unit over and remove the battery compartment door 2 Install 2 AA
Download Pdf Manuals
Related Search