Telular SX3e User's Manual
Contents
1. Fig 2 Optional high gain antenna installed on the building s exterior Always direct the antenna toward the nearest cell tower of your service provider PHONECELL SX3e AMPS 6 USER MANUAL Antenna Location amp Setup Continued How to Connect the Antenna 1 Connect the Power Supply to the DC PWR port on the back of the Phonecell see Figure 3 2 Connect the AC line cord from the power supply to the AC power source After approximately 10 seconds the LED indicator on the front of the FWT should turn RED see Figure 4 3 Connect an antenna to the TNC antenna connector on top of the FWT see Figure 5 AC Line Cord 4 Test the cellular signal strength by checking the LED indicator on the front of your Phonecell Fos e RED No Service LE 4 e YELLOW Moderate signal LED ee e GREEN Good signal Indicator 5 Move the antenna from one location to another until you achieve the best signal strength possible TIP Many things can obstruct the cellular Optional Yagi signal and moving the antenna as little as one meter 3 feet can dramatically improve signal strength and call reception AC Power eej ee L 6 When you re getting a strong GREEN signal you re ready for the next step connecting a Optional ll Standard phone and making a call Magnetic at aes Mount x F e TNC RS Antenna o a Connector WARNING Never operate your Phonecell when an2. the short screws provided see Fig 11 5 Align the holes on the mounting bracket with the two wall mounted screws Then mount the Phonecell onto the screws and slide it down ward until the screw heads lock into the bracket and the unit is secure see Figure 12 Fig 12 PHONECELL SX3e AMPS 12 User MANUAL Phonecell Installation Continued 4b Desktop Tabletop Installation a ma S After all connections are made turn your s fa i Phonecell SX3 face down and attach the four E de T i rubber feet to the bottom see Figure 13 Your a Phonecell SX3 is now ready for use on a R desktop tabletop or other flat surface JI T NOTE Do not attach the rubber feet if the eg ie E unit is to be wall mounted 7 E IMPORTANT Your Phonecell SX3 must be placed or mounted on a flat level surface to allow proper ventilation Do not block the air vents or the space beneath your Phonecell as this could cause the unit to overheat and fail PHONECELL SX3e AMPS 13 USER MANUAL Phonecell Operation Once your Phonecell SX3 is installed and tested it s ready for operation How to Use the LED Status Indicator a 1 Plug in the AC power supply ne Th 2 Wait approximately 10 seconds for the unit RE Wi to initialize LED Indicator ii naw 3 Then the LED indicator on the front of your Phonecell will turn ON The LED Status Table below describes the modes and operation of
3. this 3 color indicator LED Status Table LED Color Description RED Malfunction Hardware fault detected RED No cellular service YELLOW Moderate cellular signal strength voice YELLOW Moderate signal strength fax data GREEN Best cellular signal strength voice GREEN Best signal strength fax data RED GREEN Diagnostic programming mode OFF No Power How to Place a Call 1 Pick up your telephone handset your phone is now off hook 2 Listen for dial tone If service is not available a No Service tone is produced Hang up the phone and try again 3 Dial the phone number How to Receive a Call e When your telephone rings pick up the handset and begin talking How to End a Call e Hang up the phone place the handset back onto the telephone cradle The Hookflash Function When you initiate the Hookflash function it automatically lets you e Speed up the connection after you dial a phone number e Answer an incoming call that occurs when you re dialing a phone number e Use special supplementary cellular services which may be available in your cellular service area see Special Cellular Services on page 16 How to Use the Hookflash Function Depending upon your phone there are two ways to initiate the Hookflash function e Press the dedicated HOOKFLASH or FLASH key on your telephone e Press the hang up or switch hook mechanism on your phone once quickly approximately 2 second PHONECELL SX
4. 2 digit value between 00 and 15 otherwise the FWT will not update or store this value the existing stored parameter will remain For example to program the FWT for ACCOLC 8 enter 2 08 How to Set the Access Method EX Option Use the following key sequence to set the EX option Press Cr 3 x lt EX option gt The lt gt brackets represent the 1 digit EX option enter 1 if the FWT must always send the full MIN Mobile Identification Number when accessing the system enter amp 0 if not You must enter either 0 or 1 otherwise the FWT will not update or store this value the existing stored parameter will remain The factory default setting is 1 How to Set the Roam Option Use the following key sequence to set the Roam option Press C7 6 x lt Roam option gt The lt gt brackets represent the 1 digit Roam option enter amp 0 to enable roaming enter amp 1 to disable roaming You must enter either 0 or 1 otherwise the FWT will not update or store this value the existing stored parameter will remain The factory default setting is 0 How to Set the Dial Tone After Remote On Hook Option Use the following key sequence to set the Dial Tone After Remote On Hook option Press 7 8 x lt Dial Tone option gt The lt gt brackets represent the 1 digit dial tone option enter amp 0 for no dial tone after a remote on hook enter amp 1 to enable dial tone after remote on hook
5. A Key Press 27 x lt A Key gt S i The lt gt brackets represent your 6 to 26 digit A Key Authentication code which is supplied by your cellular service provider If the A key is less than 6 or more than 26 digits it is considered invalid and the SX3i will not update or store this the currently stored value will remain IMPORTANT For security reasons your complete A Key is never transmitted over the phone However you should keep the number in a safe place to prevent counterfeiting fraud or cloning PHONECELL SX3e AMPS 11 USER MANUAL Step 4 Install Your Phonecell After you ve selected a location and made all the necessary connections your Phonecell SX3 is ready for wall mounting or desktop installation PRE INSTALLATION TIPS e Make sure the location is dry away from overhead water pipes and protected from weather conditions e The area should be free of airborne contaminants e The Phonecell should be located within 2 meters 6 feet of an AC power outlet 4a Wall Mount Instructions 1 Hold the mounting bracket against the wall and mark two holes for the long mounting screws see Fig 8 2 Remove the bracket and drill two holes for the long mounting screws see Figure 9 3 Install the long mounting screws into the wall leaving about s inch 3 mm gap between the screw heads and the wall see Fig 10 4 Attach the mounting bracket to the back of the Phonecell SX3 using
6. calls voice mail etc Please consult your service provider for the required Data After Send In Call DTMF Signaling configuration The Data After SEND option is disabled Out of Band signaling at the factory To change the Data After SEND setting follow the steps below How To Set the In Call DTMF Signaling Option Pick up the handset and listen for dial tone Then enter the User Programming mode by pressing EE 0 12345678 The dial tone should change to a steady Programming tone and the LED indicator on the front of your Phonecell should blink alternately RED and GREEN to indicate that you re now in the Programming mode Next press 10 lt in call DTMF option gt The lt gt brackets represents the in call DTMF signaling option You must enter a value between 0 and 3 enter amp 0 for In Band Signaling enter amp 1 for Out of Band Signaling enter gt 2 for both In Band and Out of Band signaling enter amp 3 for neither If you enter the option incorrectly you ll hear three short beeps followed by the programming tone That s your cue to re try the steps above If correct you ll hear the programming tone again Hang up Your Phonecell is ready for use Zero Dial Delay for Frequently Called Numbers A new patent pending feature enables the Phonecell to recognize your frequently called phone numbers and send them immediately without the 3 second Auto SEND Delay The Phonecell stores a list of
7. on the front of your Phonecell should blink alternately RED and GREEN to indicate that you re now in the programming mode You now have two minutes to begin the programming steps below Step 3 Press 7 1 The spaces represent your 10 digit telephone number This is also called a Mobile Identification Number or MIN If you enter the number incorrectly you ll hear three short tones followed by the programming tone if correct you ll hear the programming tone again Step 4 Press 7 5 ____ The spaces represent your 1 to 5 digit System Identifier S D which ranges from 0 to 32 767 This information identifies your cellular ser vice provider For example to set up 555 enter 5 555 If you enter the SID incorrectly you ll hear three short tones followed by the pro gramming tone if correct you ll hear the programming tone again NOTE depending upon whether you enter an odd SID or an even SID the Phonecell will automatically set the remaining NAM parameters to AMPS standards as shown in the table below AMPS Standards Automatically Set NAM Parameters Odd SID Even SID Initial Dedicated Control Channel 334 First Paging Channel 334 Number of Dedicated Control Channels 21 Preferred System B Roam Option to override see page 23 Enabled Enabled If you need to override any of the settings continue with the following steps 5 8 Otherwise hang up The flashing LED indicator will become solid GR
8. up to 50 numbers in its memory This list contains any number that you ve called at least twice successfully NOTE cycling turning ON OFF the power will erase the current list A new list will be started when power is re applied To enable or disable this feature see page 24 PHONECELL SX3e AMPS 17 USER MANUAL Phonecell SX3 Troubleshooting Telephone Service is Not Working If the telephone service is not working first check the operation of the telephone equipment and wiring connected to your Phonecell SX3 Test the equipment on a different service or piece of equipment to ensure proper operation or connect a known good telephone device to the RJ 11 port on the Phonecell SX3 unit This will verify the condition of the telephone equipment and the internal wiring of the telephone service to ensure that it s working properly If the telephone system or wiring is not working properly replace or repair the equipment as required Otherwise contact your cellular provider or your authorized Telular distributor Unable to Receive Incoming Calls If more than one telephone or telephone device is connected to your Phonecell make sure that all devices are on hook hung up If one extension is off hook off its cradle none of the extensions on your phone line will ring when an incoming call occurs Moisture or Ventilation Problems Visually inspect your Phonecell units enclosure Moisture can damage the equip ment Vent
9. 1 e f your Phonecell was not pre programmed for SET NAM information you need to perform the CE gr NAM Phone Number Setup procedure gr Oo e Otherwise continue to Step 4 i Step 4 Wall or Desk Installation 12 13 e After you ve selected a location and made all es the necessary connections and adjustments your Phonecell SX3e is ready for either wall mounting or desktop tabletop use PHONECELL SX3e AMPS 5 USER MANUAL Step 1 Choose an Antenna Location Your Phonecell SX3 receives operating commands from the cellular network and relies upon signal strength for proper operation Therefore finding an antenna location with good signal strength is critical for call quality ANTENNA LOCATION TIPS e Locate the antenna above ground and as close to windows or exterior walls as possible see Fig L e Try to install the antenna in an uninhabited area i e closets attics etc to ensure a minimum separation of 16 inches 40 cm between the antenna and the inhabitants e Preferably the antenna should be mounted on the building s exterior see Fig 2 e High gain Yagi antennas must be directed toward your service provider s nearest cell tower Fig 1 Optional spike antenna e Spike antennas must be pointed upward pointed upward and located near the window for optimum signal strength e Keep antenna cable as short as possible long 3 cable runs affect call quality e Never splice antenna cable
10. 3e AMPS 14 USER MANUAL Phonecell Operation Continued Important Tones and Alerts No Service Tone When cellular service is not available the receiver emits a No Service fast beeping tone instead of the normal steady dial tone ROH Receiver Off Hook Tone If the telephone equipment remains off hook off its cradle with no dialing activity for 45 seconds the receiver emits an ROH tone for 60 seconds Incoming Call Alert If you re dialing a number and an incoming call occurs the receiver will emit an audible ring To answer the incoming call e Press the HOOKFLASH button once This will connect the incoming call e OR hang up immediately This will cause the phone to start ringing How to Adjust the Volume Level If the volume level on your phone is too high or too low you can adjust the levels using the keypad on your telephone Note your telephone must be in Tone Dial DTMF mode to adjust the levels To Increase Audio Level Increase the audio level in steps by pressing CE 8 also known as Up Continue to press 8 until the desired level is reached To Decrease Audio Level Decrease the audio level in steps by pressing CE 3 also known as Down Continue to press 3 until the desired level is reached NOTE The default setting lets you adjust the audio up to three 3 steps in either direction Up or Down Fax Data Transmission Automatic Level Setting ALS Wh
11. 78 The dial tone should change to a steady Programming tone and the LED indicator on the front of your Phonecell should blink alternately RED and GREEN to indicate that you re now in the Programming mode Next press 11 lt Auto SEND Delay gt The lt gt brackets represent the Auto SEND Delay You must enter a value between 2 and 20 seconds For instance to enter a 5 second delay press 11 5 If you enter the delay incorrectly you ll hear three short beeps followed by the programming tone That s your cue to re try the steps above If correct you ll hear the programming tone again Hang up Your Phonecell is ready for use Special Cellular Services Your Phonecell SX3 is compatible with a variety of special services such as call forwarding call waiting and more Depending upon your cellular provider these services may be available on a subscription basis However certain dialing sequences must be entered which vary among service providers Please consult your service provider for the dialing instructions for your system Call Forwarding After you hear a dial tone on your telephone handset dial the code required by the service provider wait for a minimum of 3 seconds or press the HOOKFLASH Your Phonecell automatically transmits the call forwarding information Listen for the cellular carrier response Then hang up the phone If you don t wait for the response your forwarding request may not be fulfi
12. EEN Phone number setup is complete i Continued PHONECELL SX3e AMPS 9 USER MANUAL NAM Phone Number Setup Override Commands NOTE The following NAM Parameters are automatically set by the SID value in Step 4 on the previous page These steps 5 7 are only needed if you want to override the standard AMPS settings listed on the previous page Otherwise continue to Step 4 Wall Mount or Desktop Installation pages 12 13 Step 5a How to Override the Initial Dedicated Control Channel and First Paging Channel If you have an A cellular service provider with an odd SID System Identifier enter the following 2 part key sequence Otherwise continue to Step 5b 1 First press S 24 _ 2 Next press 4 _ Note enter the same 1 to 4 digit channel in both steps above The spaces represent your 1 to 4 digit Initial Dedicated Control Channel and First Paging Channel When you turn on your Phonecell these channels help the service provider find you and vice versa NOTE The default setting is channel 333 for A service providers To change the setting you must enter a 1 to 4 digit number in the range of 0 to 1023 For example to set up channel 565 enter 24 565 If you enter the channel incorrectly you ll hear three short tones followed by the programming tone if correct you ll hear the programming tone again Step 5b If you have a B cellular service provider with an eve
13. RD CPX and AXCELL Part No 56017302 2001 Telular Corporation all rights reserved PHONECELL SX3e AMPS 2 USER MANUAL Table of Contents Introduction aE E an KEE aneia 2 Technical SUPON 5 40 tree aa e alerte raa aeria 2 Getting Started Unpacking the Phonecell SX3e 4 Pre Installation Checklist 4 Installation Summary cccce sete eeeee ee eeeeeneeeee neces eneeeeesenaesaseeeeeeeeeseseeenenees 5 Step 1 Choose an Antenna Location 6 How to Connect the Antenna ccccececceeeeeeceeeeeeeceeeeeeeaeeseeeeeesaeeseenees 7 Step 2 Plug in Your Telephone ses 8 Connect Your Telephone ss 8 Place a Call Adjust Your FWT cccceececceseceeeeeeeeeseceeeeeeeeeseaeeneeeeeee 8 Adding More Phones 8 Additional Telephone Equipment 8 Step 3 NAM Phone Number Setup smeneents 9 Optional A Key Authentication Code Setup 11 Step 4 Install Your Phonecell Wall Mount Installation cccceeeeeceeeeeeeecneeeeeeeaeeeeeeeeaeeeeeeeaaeeeeneeaaes 12 Desktop Tabletop Installation 13 Phonecell SX3e Operation How to Use the LED Display 14 How to Place a Call 14 How to Receive Call ma mirrzo neia piana aa anaa 14 How to End a Call 14 Hookflash Functidn issstssses rss in E de tact ee 14 Important Tones and Alerts 15 How to Adjust the Volume Level 15 Fax Data Transmission 15 Variable Dial Time Auto SEND Delay Opti
14. You must enter either 0 or 1 otherwise the FWT will not update or store this value the existing stored parameter will remain The factory default setting is 1 PHONECELL SX3e AMPS 23 USER MANUAL Technician Programming Commands Continued How to Set the Post Receiver Off Hook ROH Option Use the following key sequence to set the post ROH option Press 9 x lt Post ROH option gt The lt gt brackets represent the 1 digit post ROH option enter amp 0 for continuous ROH tone enter amp 1 to turn off ROH tone and periodically check for an on hook condition You must enter either 0 or 1 otherwise the FWT will not update or store this value and the existing stored parameter will remain The factory default setting is 1 How to Set the Pulse Dial Option Use the following key sequence to set the Pulse Dial option Press gt 12 lt Pulse Dial option gt The lt gt brackets represent the 1 digit Pulse Dial option enter amp 0 to disable pulse dialing capability enter amp 1 to enable pulse dialing capability You must enter either 0 or 1 otherwise the FWT will not update or store this value the existing factory default setting is 1 How to Initiate a Ring Back Request Use the following key sequence to initiate an immediate Ring Back Press 13 There is no Ring Back value to be entered the command activates when the phone is placed on hook How to Restore the Factory Default S
15. ee eee TELULAR 0e PHONECELL SX3e AMPS FIXED WIRELESS TERMINAL USER MANUAL Total communications freedom at your fingertips voice fax data 06 25 01 Part No 56017302 Introduction TE Ph E 7 i z Computer l a ES Modem Battery Back Up Seeds 5 Ter Thank you for choosing the Phonecell SX3 Fixed Wireless Terminal from Telular This innovative product lets you connect up to five pieces of standard telephone equipment into a cellular network for total communications flexibility Please follow this guide to unpack set up and operate your new Phonecell safely and properly Telular is proud to welcome you as a valued customer Your satisfaction is our most important concern Telular Corporation Corporate Headquarters 647 North Lakeview Parkway Vernon Hills Illinois 60061 USA TECHNICAL SUPPORT Tel 847 247 9400 e Fax 847 247 0021 E mail mainoffice telular com hitp www telular com Patents Telular Corporation products are protected and manufactured under one or more of the following U S patents and related international patents and patents pending relating thereto 4 658 096 4 737 975 4 775 997 4 868 519 4 922 517 5 134 651 5 361 297 5 469 494 5 046 085 5 715 296 Trademarks Telular Corporation owns the following registered trademarks TELULAR and design TELULAR CELUACK MAXJACK TELCEL HEXAGON LOGO PHONECELL CELSERV TELGUA
16. en your Phonecell SX3 detects a fax or modem call it automatically adjusts the Transmit and Receive audio levels for optimum data transmission After the fax data transmis sion is completed the FWT resets the audio levels to their previous settings Fax Modem Compatibility Your Phonecell is compatible with all Group 3 facsimile machines and computer modems Depending upon the type of modem used and the cellular network s capability data transmis sion rates of 2400 baud and higher are normally possible D a M a IE Sa PHONECELL SX3e AMPS 15 USER MANUAL Phonecell Operation Continued Variable Dial Time Auto SEND Delay Option When you place a call your Phonecell SX3 automatically sends the phone number over the cellular network after you dial the last digit just like a landline phone However to make sure you have enough time to dial the last digit a 3 second Auto SEND Delay is programmed into the unit This delay also affects Special Functions such as Call Forwarding see Special Cellular Services below You can set the Auto SEND Delay from 2 to 20 seconds using an ordinary tone dial DTMF phone which is sometimes referred to as a POTS Plain Old Telephone Service phone Note you cannot change the delay while you re making a call How To Adjust the Auto SEND Delay Pick up the telephone handset and listen for dial tone Then enter the User Programming mode by pressing CE 0 123456
17. et phone NOTE the Technician Programming mode is not accessible while in a call In the following sections an lt entered value gt is comprised of the digits 0 through 9 The digits and are considered invalid when used inside an lt entered value gt and will cause that command value to be rejected When you enter the programming mode a timer is started If there are no key entries within any 2 minute period the FWT will revert to its normal mode Going on hook hanging up the phone will exit the programming mode How to Enter the Technician Programming Mode Use the following access code to enter the Programming mode Press 0 12344321 The access code is 8 digits If the access code is not 8 digits or does not match the stored access code the Technician Programming mode cannot be not entered This code is pre programmed during production and cannot be changed in the field If you enter the access code correctly the dial tone should change to a different steady Programming tone and the LED indicator on the front of the Phonecell will blink alternately RED and GREEN to indicate that you re in the programming mode PHONECELL SX3e AMPS 22 User MANUAL Technician Programming Commands Continued How to Set the Access Overload Class ACCOLC Use the following key sequence to set the ACCOLC Press gt 2 lt ACCOLC gt The lt gt brackets represent the 2 digit ACCOLC You must enter a
18. ettings Use the following key sequence to restore the factory default settings Press 15 x There is no Restore Defaults value to be entered the command acti vates immediately If you enter a value it will be invalid and the FWT will not restore the factory defaults Note NAM Phone Number Setup data is not affected by this command and will not be changed How to Enable Disable the Zero Dial Delay Option Use the following key sequence to set the Zero Dial Delay option Press E 21 x lt Zero Dial Delay option gt The lt gt brackets represent the 1 digit Zero Dial Delay option enter 0 to disable Zero Dial Delay option enter 1 to enable Zero Dial Delay option You must enter either 0 or 1 otherwise the FWT will not update or store this value the existing stored parameter will remain The factory default setting is 1 PHONECELL SX3e AMPS 24 User MANUAL Technician Programming Commands Continued How to Enter the Periodic Self Test Option Use the following key sequence to program the periodic self test Press Ce x 76 x lt self test interval gt The self test interval is programmed in 1 minute intervals from 1 to 65 535 A value of 0 disables the self test If the value is not between 9 and 65 535 it will be considered invalid The factory default setting is 180 PHONECELL SX3e AMPS 25 USER MANUAL Part No 56017302 2001 Telular Corporation
19. from external RF energy You should also check with the manufacturer of any equipment that has been added to your vehicle Consult the manufacturer of any personal medical devices such as pacemakers hearing aids etc to determine if they are adequately shielded from external RF energy Turn your Phonecell SX3 FWT OFF in health care facilities when any regulations posted in the areas instruct you to do so Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy Aircraft Turn OFF your Phonecell SX3 before boarding any aircraft A e Use it on the ground only with crew permission e Do not use it in the air To prevent possible interference with aircraft systems U S Federal Aviation Administration FAA regulations require you to have permission from a crew member to use your cellular phone or any other cellular product while the plane is on the ground To prevent interference with aircraft systems FCC regulations prohibit using your cellular phone system while the plane is in the air Children Do not allow children to play with your Phonecell to prevent damage to the unit Blasting Areas Construction crews often use remote control RF devices to set ad off explosives Therefore to avoid interfering with blasting operations turn your Phonecell SX3 OFF when in a blasting area or in areas posted Turn off two way radio PHONECELL SX3eAMPS 20 USER MANUAL Safety Informatio
20. he FWT with a damaged antenna If a damaged antenna comes into contact with the skin a minor burn may result Have your antenna replaced by a qualified technician immediately Use only a manufacturer approved antenna Unauthorized antennas modifica tions or attachments could damage the FWT and will void the Grant of Type Acceptance WARNING Your Phonecell SX3 must be placed or mounted on a flat level surface to allow proper ventilation Do not block the air vents or the space beneath your Phonecell as this could cause the unit to overheat and fail PHONECELL SX3e AMPS 19 User MANUAL Safety Information Continued Driving Check the laws and regulations on the use of cellular products in the areas where you drive Some jurisdictions prohibit your using a cellular device while driving a vehicle Even if your jurisdiction does not have such a law we strongly suggest that for safety reasons the driver use extreme caution when operating the cellular device while the vehicle is in motion Always obey the law Electronic Devices Most modern electronic equipment is shielded from RF energy However RF energy from cellular devices may affect inadequately shielded electronic equip ment RF energy may affect improperly installed or inadequately shielded electronic operating and entertainment systems in motor vehicles Check with the manufac turer or its representative to determine if these systems are adequately shielded
21. ilation is also very important If there are moisture or ventilation problems move your Phonecell SX3 to correct as necessary No Power The LED lamp on the front of your Phonecell SX3 indicates the unit s power con dition If the LED is RED YELLOW or GREEN your Phonecell is receiving power If the power cord is connected and the LED lamp is not lit the Phonecell is not receiving power Verify that the AC power source and its corresponding circuit breaker are functioning properly Battery Backup Failure If you re using the optional Battery Backup Unit the unit must be connected to AC power for at least 24 hours to fully charge the batteries before they ll back up your Phonecell SX3 Verify that the batteries have been charged for at least 24 hours and that the power source and its corresponding circuit breaker are functioning properly Then examine the batteries for wear and corrosion Replace the batteries if necessary WARNING Only Authorized Service Personnel should remove the cover of your Phonecell SX3 For further assistance contact your Authorized Telular Representative Please have your unit s model and serial number ready PHONECELL SX3e AMPS 18 USER MANUAL Safety Information IMPORTANT To ensure safe and efficient operation please read the following information and observe these guidelines whenever using your Phonecell SGF WT t Your Phonecell SX3 FWT Fixed Wireless Terminal functions as E bo
22. lled You can set this delay for 2 to 20 seconds See the Variable Dial Time section above NOTE please wait 1 second longer than the delay programmed i e for the 3 second delay mentioned above wait 4 seconds Call Waiting If your cellular provider requires codes to be entered involving dig its 1 9 and to answer a waiting call the Out of Band Signaling option must be enabled See the Data After SEND option on page 17 PHONECELL SX3e AMPS 16 USER MANUAL Phonecell Operation Continued Three Way Conference Calls For three way conference calls the Out of Band Signaling option must be enabled Pressing the HOOKFLASH function transmits the SEND command Please see the Data After SEND option below Voice Mail Out of Band Signaling may need to be disabled to interact with remote voice mail systems to prevent double pulsing See the Data After SEND option below Authentication A Key Depending upon your cellular provider you may be required to enter an Authentication Code A Key before you make or receive any calls A Key is a cellular system solution to prevent cloning counterfeiting and cel lular fraud To program the A Key function see the Technician Programming Section page 25 Data After SEND n Call Signaling Option Depending upon your cellular provider the Data After SEND option may need to be Enabled or Disabled to use special cellular features such as call waiting three way conference
23. n Continued Potentially Explosive Atmospheres Turn your Phonecell SX3 OFF when in any area with a potentially explosive atmosphere It is rare but your Phonecell SX3 or its accessories could generate sparks Sparks in such areas could cause an explosion or fire result ing in bodily injury or even death Areas with a potentially explosive atmosphere are often but not always clearly marked They include fueling areas such as gas stations below deck on boats fuel or chemical trans fer or storage facilities areas where the air contains chemicals or particles such as grain dust or metal powders and any other area where you would normally be advised to turn off your vehicle engine Do not transport or store flammable gas liquid or explosives in the area of your Phonecell SX3 or accessories Vehicles using liquefied petroleum gas such as propane or butane must comply with the National Fire Protection Standard FPA 58 For a copy of this standard contact the National Fire Protection Association One Batterymarch Park Quincy MA 02269 Attn Publications Sales Division FCC Part 15 Class B Compliance This Phonecell SX3 model has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a resi dential installation This equipment generates uses and can radiate radio freque
24. n cy energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guaran tee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment OFF and ON the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the antenna e Increase the separation between the equipment and the terminal e Connect the equipment into an outlet on a circuit different from that to which the terminal is connected e Consult your Authorized Telular Distributor or an experienced radio TV techni cian for help PHONECELL SX3e AMPS 21 USER MANUAL AMPS Technician Programming IMPORTANT The following commands may be used by a trained service technician to change the configuration of the Phonecell SX3 WARNING these commands are intended for use by trained service technicians only Untrained users could damage the Phonecell violate local regulations and breach the service agree ment with the cellular provider For further assistance please contact your Authorized Telular R epresentative AMPS Technician Programming Commands The Phonecell SX3 can be programmed on location with an ordinary telephone which is sometimes referred to as a POTS Plain Old Telephone S
25. n SID System Identifier enter the following 2 part key sequence 1 First press 25 _ 2 Next press CS 4 _ Note enter the same 1 to 4 digit channel in both steps above The spaces represent your 1 to 4 digit Initial Dedicated Control Channel and First Paging Channel When you turn on your Phonecell these channels help the service provider find you and vice versa NOTE the default setting is channel 334 for B service providers To change the setting you must enter a 1 to 4 digit number in the range of 0 to 1023 For example to set up channel 566 enter 25 566 If you enter the channel incorrectly you ll hear three short tones followed by the programming tone if correct you ll hear the programming tone again Continued PHONECELL SX3e AMPS 10 User MANUAL NAM Phone Number Setup Override Commands Step 6 How to Override the Number of Dedicated Control Channels Press gt 26 __ The spaces represent your 2 digit range of Dedicated Control Channels When you first turn on the Phonecell it automatically scans up to 21 control channels looking for your cellular provider Then it locks onto the strongest signal NOTE the factory default setting is 21 channels To change the number of channels you must enter a 2 digit value in the range of 01 to 21 For instance to set up 9 control channels enter 26 09 If you enter the range incorrectly you ll hear three short tones followed b
26. on 16 Special Cellular Services 16 Data After SEND In Call DTMF Signaling Option 17 Zero Dial Delay for Frequently Called Numbers 0 cccsesceeeeeeseees 17 Phonecell SX3e Troubleshooting snes 18 Important Safety Information ns 19 AMPS Technician Programming How to Enter the Programming Mode 22 How to Set the Access Overload Class ACCOLC n se 23 How to Set the Access Method EX Option ccceeeceeeeeeeeesees 23 How to Set the Roam Option 23 How to Set the Dial Tone After Remote On Hook Option 23 How to Set the Post Receiver Off Hook ROH Option 24 How to Set the Pulse Dial Option 24 How to Initiate a Ring Back Request 24 How to Restore the Factory Default Settings ccceseeeeerees 24 How to Enable Disable the Zero Dial Delay Option sseeesseesseeens 24 PHONECELL SX3e AMPS 3 USER MANUAL Getting Started Un Packing Your Phonecell SX3e ms ES H al E b 2 The Phonecell SX3e comes with the following Phonecell SX3e Fixed Wireless Terminal FWT Mounting Bracket with Two Screws Four Rubber Feet for Desktop Tabletop Use Do not attach feet if wall mounting the Phonecell Carefully remove the unit from the shipping carton and check for evidence of shipping damage If damage is found contact your Authorized Telular Distributor or shipping agent immediately P
27. ou can only make one phone call at a time Additional Telephone Equipment If you plan to use a device other than a x f telephone with your Phonecell SX3 such bees fe a ee asa modem make sure that device will equipment to your Phonecell SX3e work with a normal wired telephone line To 1 Modem Fax Machines Connect a fax machine IMPORTANT the same way it needs to be set up for iene odnowienie use on a regular wired telephone line t lephone egulpmenkto your PBX KSU Systems PABX Phonecell SX3 is properly installation should only be performed protected from all transient by experienced telephone technicians voltages including lightning PHONECELL SX3e AMPS 8 USER MANUAL Step 3 NAM Phone Number Setup IMPORTANT If your Phonecell was NOT pre programmed for NAM Number Assignment Module Phone Number information follow the steps below Otherwise continue to STEP 4 pages 12 13 You can program the Phonecell SX3 with an ordinary tone dial DTMF telephone which is sometimes referred to as a POTS Plain Old Telephone Service phone NOTE this programming mode is not accessible while you re in a call Step 1 Pick up the POTS handset and listen for a tone either a steady dial tone or a beeping no service tone Step 2 Enter the Master Programming mode by pressing Ce 0 12344321 The dial tone should change to a different steady Programming tone and the LED indicator
28. re Installation Checklist Before attempting Phonecell SX3e installation make sure you have the following components tools and materials Components Needed Not Supplied External Power Supply with AC Line Cord Antenna Spike Magnetio Mount or Yaa RJ 11 Modular Phone Cord Length varies according to your specific installation and the number of phones you plan to connect CD amp Dr Screwdriver inch 3 75 om Mounting Serews _ PHONECELL SX3e AMPS 4 USER MANUAL Installation Summary There are four steps to installing the Phonecell SX3e FWT properly These steps are summarized below and explained in detail in the remainder of this manual Step 1 Choose an Antenna Location 6 7 i e Choose a location e Next connect power to the ill FWT and turn the unit ON Fr e Then connect the antenna not supplied FF e Check the cellular signal strength and FA move the antenna until you achieve the best signal possible a Step 2 Plug In Your Phone page 8 i e Once the antenna is connected hook up i a phone e Then make a test call to check noise levels and adjust the antenna location accordingly e NOTE If your Phonecell SX3e is not pre pro grammed for NAM Number Assignment Module z information you ll need to perform the y NAM Phone Number Setup in Step 3 Then return to this step 2 EE e Plug in additional phones Fax and or Modem Step 3 NAM Phone Number Setup pg 9 1
29. th a radio transmitter and receiver When it is ON the FWT receives and sends out radio frequency RF energy The unit may FE operate in frequency ranges between 824 MHz and 894 MHz The FWT employs commonly used frequency modulation FM tech a niques When you use your Phonecell SX3 the cellular system pa handling your call controls the power level at which your unit trans k mits The power level can range from 0 006 watt to 3 watts Exposure to RF Radio Frequency Energy In 1991 the Institute of Electrical and Electronics Engineers IEEE and in 1992 the American National Standards Institute ANSI updated the 1982 ANSI Standard for safety levels with respect to human exposure to RF energy After reviewing the available body of research more than 120 scientists engineers and physicians from universities government health agencies and industry developed this updated Standard In March 1993 the U S Federal Communications Commission FCC proposed the adoption of this updated Standard The design of your Telular Phonecell SX3 FWT complies with this updated Standard Of course if you want to limit RF exposure even further than the updat ed ANSI Standard you may choose to control the duration of your calls and oper ate your phone in the most power efficient manner Safe Operation Requirement Do not operate your Phonecell SX when any person is within 16 inches 40 cm of the antenna Antenna Care and Replacement Do not use t
30. y person is within 16 inches 40 cm of the antenna LED Indicator a LI D Fig 5 a PHONECELL SX3e AMPS 7 USER MANUAL Step 2 Plug In Your Telephone The Phonecell SX3 lets you connect up to 5 pieces of standard telephone equipment into a cellular network Follow the steps below for quick installation Connect Your Telephone Oa 1 Locate the modular RJ 11 line port i on your phone and plug in one end Ji of a standard RJ 11 phone cord 2 Connect the other end of the cord 4 to the RJ 11 port on the back of Fig 6 x your Phonecell SX3e see Fig 6 ee Place a Call Adjust Your FWT To RJ 11 Port 1 1 Pick up the phone receiver and listen E for dial tone 2 If you hear dial tone make a call Phone Cord 3 While you re talking with the other party listen for static and echo If you ell hear either move the antenna until ay EF To Phonels z PU mMM E you find the spot where voice ne conversation is strong and static and echo are minimized NOTE If you are unsuccessful in dialing out it s probably due to one of the following e The antenna location needs to be adjusted see Step 1 page 6 7 e The NAM Phone Number needs to be set up see Step 3 page 9 11 e Your cellular phone number has not been activated contact your cellular service provider Adding More Phones Plug in an RJ 11 line splitter not sup plied to connect additional phones to your FWT see Fig 7 NOTE y
31. y the programming tone if correct you ll hear the programming tone again Step 7 How to Override the System Preference Press 7 7 _ The space represents your 1 digit system preference enter 0 for System A preferred enter 1 for System B preferred enter 2 for System A only enter 3 for System B only This sets the preference for your cellular provider If you enter the preference incorrectly you ll hear three short tones followed by the programming tone if correct you ll hear the programming tone again Step 8 Hang up The flashing LED indicator will become solid GREEN Optional A Key Authentication Code Programming Depending upon your cellular service provider you may be required to enter an Authentication Code A Key before you make or receive any calls Contact your service provider to determine whether A Key is required The A Key is a cellular system solution to prevent cloning counterfeiting and cel lular fraud It s a unique 6 to 26 digit code provided by your service provider that validates your MIN Mobile Identification Number and ESN Electronic Serial Number before you make or receive calls Once you ve entered the A Key your Phonecell automatically verifies the code with the cellular provider before every call There s no need to re program the unit unless you switch to a new service provider or change your MIN Use the following key sequence to program the
Download Pdf Manuals
Related Search