Tekkeon ezTalker ET3000 User's Manual
Contents
1. Wearing ezTalker digital ezTalker digital is designed to fit comfortably in your ear The earhook can be positioned to be worn on the right or left ear The battery is housed in the earhook so the earhook must be connected to use the headset To Place the Headset on Your Ear 1 Hook the earhook over the top of your ear and place the speaker in your ear with the tip of the headset angled toward your mouth To Change the Direction of the Earhook 1 Holding the stem of the earhook gently pull the earhook from the headset 2 Insert the earhook into the hole on the opposite side of the headset For right ear v For left ear ezTalker Using ezTalker digital Powering ezTalker digital To Turn On the Headset 1 Press and hold the TALK button approximately four seconds until On then Standby appears on the display or until you hear the ON tone The headset turns on and is placed in standby mode ready to make and receive calls Note To conserve power the display will turn off after being idle for 18 seconds To view the display simply press any button To Turn Off the Headset 1 With both the headset and the display turned on press and hold the TALK button approximately four seconds until Off appears on the display and the headset turns off or until you hear the OFF tone Understanding the Display The display is made up of four sections including status icons caller ID caller name and he2. USER GUIDE 19 FCC Statement for Class B Digital Devices This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try and correct the interference by one or more of the following measures Reorient or locate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesire
3. Call it supported hy your mohile phone 1 When you hear call waiting tone while on a call press and hold the VOLUME DOWN button for three seconds 7 e first call will be placed on hold and the second call is connected 2 To switch between the calls press and hold the VOLUME DOWN button again The current call will be placed on hold and the other call is connected NOTE For some mobile phones you must configure the phone to answer calls directly on your Bluetooth headset Refer to the mobile phone user guide for instructions for initiating this feature USER GUIDE 11 Ending Calls 1 When you have finished your call press the headset TALK button The call will be disconnected Transferring Calls You can transfer calls from your mobile phone to your headset and from your headset to your mobile phone To Transfer Calls from Your Mobile Phone to the Headset 1 Press any button on the headset to turn on the display if off 2 With the call connected to your mobile phone press the TALK button on your headset The call will be transferred to your headset To Transfer Calls from Your Headset if supported by your mobile phone 1 With the call connected to your headset press and hold the TALK button on your headset until you hear the Transfer tone about three seconds The call will be transferred to your mobile phone ezTalker 12 digital Browsing the Phone Book Directly from your headset you can browse and dial n
4. three sections Once these steps are completed you will be ready to use ezTalker digital Charging ezTalker digital Before using ezTalker digital you must charge the headset for a minimum of two hours When fully charged the battery provides up to five hours of talk time and up to 120 hours of standby time The battery status icon and a beep heard every 32 seconds will indicate a low battery less than 1096 of capacity To Charge the Headset 1 Plug the power adapter into the charging jack on the side of the earhook 2 Plug the power adapter into a wall outlet The green charging LED on the headset will light while the headset is charging When the headset is fully charged the battery icon MW will indicate full and the green LED will turn off 3 Unplug the power adapter from the wall outlet and the headset NOTE The battery can be charged when the earhook is either connected to or disconnected from the headset ezTalker 4 digital Pairing ezTalker digital to Your Mobile Phone Pairing is the process of linking the headset with your Bluetooth mobile phone or other Bluetooth device that supports a headset and or handsfree profile Before using ezTalker digital with your mobile phone you must pair the devices After this process is complete you can use the headset with your paired mobile phone You can pair ezTalker digital with up to seven Bluetooth devices Once each device is paired with the headset you must disconnec
5. Audible indication of requested actions is provided through tones heard through the headset Following are descriptions of the visual and audible indicators Visual Indicators Message Indicates Caller ID Phone number of incoming call ID blocked will appear on the display if caller ID is blocked Caller Name Name of calling party is stored in your mobile phone book Pairing In pairing mode Connecting Trying to connect Ready Headset is in standby mode ready to make or receive a call On Headset has been turned on Off Headset has been turned off Ring An incoming call is ringing on the headset Answered An incoming call has been answered Reject An incoming call has been rejected Redial The last called number is being dialed Voice Dial The call is being made using voice commands Calling A call is being placed using the mobile phone book or a stored number ID blocked The caller ID feature has been blocked ID enabled The caller ID feature has been enabled USER GUIDE 15 Visual and Audible Indicators continued LED Status Indicators Status Flashes at two second intervals Indicates Headset is in standby mode ready to make and receive calls Is off Audible Indicators Tone Double beep increasing in pitch Headset is off Indicates Headset has been turned on Double beep decreasing in pitch Headset is about to turn off A beep every 32 seco
6. Press the TALK button The call is automatically connected to your headset NOTE Phone numbers stored on the phone not on the SIM card are displayed in the order they were stored on your mobile phone not in alphabetical order ezTalker 10 digital Receiving Calls When you receive a call on your mobile phone you will hear the mobile phone ring before you hear the ring tone through your headset as there is a small delay before the headset recognizes the incoming call If you do not wish to answer the call you can use the Call Reject feature to reject the call and send the caller to voice mail if available If the Call Waiting feature is supported by your phone you can answer an incoming call while you are connected on another call In this case the connected call is placed on hold and the incoming call is connected While both calls are connected you can toggle between both To Receive a Call 1 When you hear ring tone on your headset or see Ring and the caller ID in the display press the headset TALK button The call is automatically connected to your headset and Answered appears in the display To Reject an Incoming Call it supported hy your mohile phone 1 When you hear ring tone on your headset or see Ring in the display press and hold the TALK button for three seconds until you hear the call reject tone The call will be sent to voice mail and will no longer ring on the headset To Receive a Call Waiting
7. Tekkeon ez lae tli ital Bluetooth Headset with OLED Display ET3000 User Guide O Bluetooth USER GUIDE ez falker Contents VBINION o o eor RU M MEM Rea eaa uai qu M E M E NIE MUS 2 Getting Started Unpacking ezTalker digital Getting to Know ezTalker digital Setting Up ezTalker digital Charging ezTalker digital Pairing ezTalker digital to Your Mobile Phone Wearing ezTalker digital Using ezTalker digital Powering ezTalker digital Understanding the Display Making Calls Receiving Calls Ending Calls Transferring Calls Browsing the Phone Book wld Enabling Caller ID Name Adjusting the Volume Muting ezTalker digital Visual and Audible Indicators Visual Indicators LED Status Indicators Audible Indicators Troubleshooting Limited Warranty Disclaimer of Warranties FCC Statement for a Class B Digital Device ing n e EE Overview ezTalker digital by Tekkeon is a Bluetooth headset with a unique OLED digital display that lets you cut loose from your Bluetooth mobile phone With advanced features like stored number redial last number redial and voice dialing you can use the headset to make and receive calls without every touching your mobile phone You can even access and dial from your mobile phone book for some mobile phones While using your ezTalker digital headset you can store your mobile phone in your pocket backpack or b
8. adset status A sample display is shown on page 8 USER GUIDE 7 Se Ln J C O ul Hb cos i 7148321260 CaerD CL Tekkeon f CaerName 7 Ring Ses The icons in the first two positions will change according to the mode Following is a description of the icons ea Ce Headset has no audio connection Headset is in talk mode E QD Headset is in standby mode Headset is in talk mode alll Volume level Tih Battery level ezTalker 8 digital Making Calls You can make calls from your mobile phone or directly from ezTalker digital using the last number redial feature voice dialing commands the stored number redial feature or by accessing your mobile phone book from the headset if these features are supported by your mobile phone To Make Calls from Your Mohile Phone 1 Dial the number from your mobile phone The call is automatically connected to your headset To Make Calls Using Last Number Redial if supported by your mobile phone 1 Press any button on the headset to turn on the display 2 Press and hold the VOLUME UP or VOLUME DOWN button for three seconds while the phone is in standby mode Redial will appear on the display and the last number dialed from your mobile phone will be dialed automatically if this feature is supported by your mobile phone To Make Calls Using Voice Dialing if supported by your mobile phone 1 Pr
9. caller ID disabled simultaneously press the VOLUME UP and VOLUME DOWN buttons ID enabled will appear on the display Adjusting the Volume The volume can be adjusted using the volume controls on ezTalker digital or your mobile phone To Increase the Volume 1 While in talk mode press and release the VOLUME UP button Repeat until you reach the desired level The volume level icon wll will change accordingly To Decrease the Volume 1 While in talk mode press and release the VOLUME DOWN button Repeat until you reach the desired level The volume level icon wll will change accordingly Muting ezTalker digital You can mute and un mute the microphone temporarily so that you cannot be heard by the connected party To Mute the Headset 1 While in talk mode press and hold the VOLUME UP button for three seconds While the headset is muted you will hear a beep every four seconds To Un Mute the Headset 1 When the microphone is muted press and hold VOLUME UP button for three seconds ezTalker 14 digital Visual and Audible Indicators ezTalker digital uses visual and audible indicators to provide the status of the headset For visual indicators the headset provides caller ID display icons to indicate headset state connection status and volume and battery level and text and a blue LED that provide operation status The icons are described in Understanding the Display and the text and LED are described in this section
10. d operation of the device Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment ezTalker 20 digital Customer Support If you product is in need of repair or replacement please contact the Tekkeon Customer Support Center at Tekkeon Inc c o ezTalker digital 3002 Dow Avenue 134 Tustin CA 92780 888 787 5888 714 832 1266 www tekkeon com Tekkeon Inc will issue a Return Merchandise Authorization RMA number for all repairs or exchanges Tekkeon www tekkeon com 2005 Tekkeon Inc All Rights Reserved ezTalker is a trademark of Tekkeon Inc
11. ess any button on the headset to turn on the display 2 Press the TALK button on your headset Voice Dial will appear on the display 3 After you hear a beep usually between one to four seconds speak the name of the person you wish to call You will hear the spoken name if provided by your phone and the call will be automatically connected to your headset TIP In a noisy environment where the noise may interfere with voice commands you should dial from the mobile phone keypad or use any of the advanced calling features to make the call from the headset if supported by your mobile phone USER GUIDE 9 To Make Calls Using Stored Number Redial 1 With the headset off press the VOLUME UP button to turn on the display and put the headset in stored number browse mode The display will turn on 2 Press the VOLUME UP button forward or VOLUME DOWN button backward to scroll through the numbers stored in your mobile phone until you reach the desired number 3 Press the TALK button The call is automatically connected to your headset To Make Calls Using Your Mobile Phone Book it supported by your mobile phone 1 With the headset off press the VOLUME DOWN button to turn on the display and put the headset in phone book browse mode 7he display will turn on 2 Press the VOLUME UP button forward or VOLUME DOWN button backward to scroll through the numbers stored in your mobile phone until you reach the desired number 3
12. event of a defect in operation during the warranty period Tekkeon Inc will replace the defective product when the owner returns all product contents The limited warranty will be considered void if the unit is tampered with subject to misuse negligence or accidental damage has been improperly serviced or if the security seal is removed This warranty is limited to replacement only and shall not cover any other damages Any product returned to Tekkeon Inc with no fault found will be returned to the owner at the owner s expense To obtain warranty coverage please complete and submit the enclosed ezTalker digital registration card Disclaimer of Warranties Any user of this product does so at the user s own risk To the maximum extent permitted by applicable law Tekkeon Inc and its suppliers provide the hardware and any support services related thereto as is and with all faults and hereby disclaim all warranties and conditions whether express implied or statutory including but not limited to implied warranties of merchantability fitness for a particular purpose non infringement lack of negligence or correspondence to description except for those warranties specifically and expressly provided in the Limited Warranty With respect to the use of this product in no event shall the company be liable for any loss of profit or any other commercial damage including but not limited to special incidental consequential and other damages
13. n you are using ezTalker digital Ensure that your mobile phone supports this feature and is set to voice control mode If your mobile phone supports voice dialing and you are in a noisy environment dial the number from the mobile phone as the loud background noise may interfere with the voice commands Last number redial isn t working Call reject isn t working Ensure that your mobile phone supports this feature Ensure that your mobile phone supports this feature Call waiting isn t working Ensure that your mobile phone supports this feature You cannot transfer a call from your headset to your mobile phone USER GUIDE Ensure that your mobile phone supports this feature 17 Troubleshooting continues Issue When you receive a call on your mobile phone the call is not automatically connected to ezTalker digital after you press the TALK button Solution Ensure that your ezTalker digital headset is charged and turned on hs Ensure that your Bluetooth mobile phone is set to Bluetooth mode and that ezTalker digital BTHS has been selected as the connected Bluetooth device This is important as most Bluetooth phones are designed to pair with more than one Bluetooth device co This problem may persist in some rare cases as the phone may be too busy to process the call and have difficulty establishing the connection with the headset If this is the case answer the call on
14. nds Battery is low Double chime followed by low beep Headset has been put into pairing mode Beeps every four seconds while a call is connected 16 Headset is muted ezTalker Troubleshooting Issue When you initiate the Bluetooth device pairing feature on your mobile phone your phone cannot find ezTalker digital Solution Verify that ezTalker digital is placed in pairing mode Pairing is shown on the display If not place the headset in pairing mode Your ezTalker digital headset is not communicating with your mobile phone Ensure that the headset is on and charged and that you have paired the headset with your Bluetooth mobile phone ezTalker digital will not work with any mobile phone that does use Bluetooth wireless technology You are encountering poor reception via the ezTalker digital headset You cannot browse numbers stored in your mobile phone book Verify that you have good reception on your mobile phone or move closer to your mobile phone If the reception is still poor try moving the mobile phone away from your body or to the same side of your body as your headset Verify that your phone supports this feature This list is available at www tekkeon com mobilephonebook If so verify that the numbers are stored in the mobile phone and not on the SIM card as numbers stored on the SIM card will not be displayed Your mobile phone does not accept voice commands whe
15. riefcase just about anywhere in close proximity that is convenient for you ezTalker digital is designed with Bluetooth v1 2 technology and is backward compatible with all Bluetooth v1 1 devices Getting Started Unpacking ezTalker digital E Your ezTalker digital package includes ma the following ezTalker digital Headset and Earpiece 4 Power Adapter 2 digital ezTalker Getting to Know ezTalker digital VOLUME UP Button TALK Button VOLUME DOWN Button Increases the speaker volume Used to turn headset on off Decreases the speaker volume initiates mutes unmutes the microphone pair and make receive calls last number redial and call waiting and and enables scrolling through stored numbers enables scrolling through phone book Charging LED Indicates when headset is being charged Earhook Houses battery and can be positioned to be Charging Jack worn on either ear Input for power adapter to charge the headset Blue LED OLED Digital Display Provides visual indication Provides caller ID and call status and visual of headset status indication of audio and headset connection volume level and headset battery level USER GUIDE 3 Setting Up ezTalker digital Before using ezTalker digital you must Charge ezTalker digital Pair ezTalker digital to your mobile phone Adjust ezTalker digital to your ear preference Directions for each of these activities are provided in the following
16. t the paired phone or device to connect to a different phone or device While connected to a different paired device ezTalker digital will not be connected to other paired devices BEFORE YOU PAIR THE HEADSET ENSURE THAT THE BATTERY IS FULLY CHARGED AND REVIEW THE INSTRUCTIONS IN YOUR MOBILE PHONE USER GUIDE FOR PAIRING YOUR MOBILE PHONE TO A BLUETOOTH HEADSET To Pair the Devices 1 Turn on the mobile phone device and place it next to the headset 2 Initiate the Bluetooth device pairing discovery feature on the mobile phone device Refer to the mobile phone device user guide for instructions on initiating this feature 3 With the headset turned off press and hold the TALK button until Pairing appears on the display approximately five seconds 4 Release the TALK button 7he headset is now in pairing mode 5 Follow the mobile phone device prompts and when prompted for the passkey also called passcode or BT PIN enter 0000 the ezTalker digital passkey When pairing is complete the headset will be placed in standby mode ready to make and receive calls Ready will appear on the display and the blue LED Will flash at two second intervals USER GUIDE 5 To Cancel Pairing Mode While you are in pairing mode you can cancel the pairing process and turn off the headset 1 While in pairing mode press and hold the TALK button approximately three seconds until Off appears on the display and the headset turns off
17. the mobile phone before pressing the TALK button on the headset The mobile phone should transfer the call to your headset within one second Even though your headset is turned on the call is not automatically connected to ezTalker digital when you dial a number on your mobile phone E Ensure that your Bluetooth mobile phone is set to Bluetooth mode and that ezTalker digital BTHS has been selected as the connected Bluetooth device This is important as most Bluetooth phones are designed to pair with more than one Bluetooth device 2 The problem may persist in some rare cases as the phone may be too busy to process the call and have difficulty establishing the connection with the headset If this is the case make a call from your mobile phone and then press the TALK button on the headset The mobile phone should transfer the call to your headset within one second You hear a crackling noise when connected on a call through the headset You have exceeded the 30 foot range of the Bluetooth connection Move your mobile phone closer to the headset You hear a clicking noise when connected on a call through the headset 18 You are experiencing interference on the connection between your mobile phone and the headset Try changing locations ezTalker Limited Warranty The product enclosed herein is warranted to be free of operational defects for a period of one year from the date of purchase In the
18. umbers stored on your mobile if supported by your mobile phone NOTE Phone numbers stored on the phone not on the SIM card are displayed in the order they were stored on your mobile phone not in alphabetical order Some mobile phones only display the first number stored for a contact such as home and will not display all the numbers for that contact This feature is supported by many phones For a list of phones that support this feature go to www tekkeon com mobilephonebook To Browse the Phone Book 1 With the headset off press the VOLUME DOWN button to turn on the display and put the headset in phone book browse mode The display will turn on 2 Press the VOLUME UP button forward or VOLUME DOWN button backward to scroll through the numbers stored in your mobile phone until you reach the desired number 3 To make a call press the TALK button when the desired number appears The call is automatically connected to your headset NOTE When you browse the phone book the caller ID name function is automatically enabled Enabling Caller ID Name Caller ID name is automatically enabled on your headset if supported by your mobile phone You can disable caller ID name if you do not wish others to see the ID or name of the incoming caller To Disable Caller ID Name 1 Simultaneously press the VOLUME UP and VOLUME DOWN buttons D blocked will appear on the display USER GUIDE 13 To Enable Caller ID Name 1 With
Download Pdf Manuals
Related Search