Teka ND.3 User's Manual
Contents
1. Avoid connecting the appliance to conductors used as exits for fumes produced by a non electric energy source e g boilers chimneys etc If the extractor fan is going to be used simultaneously with equipment powered by a non electric energy source e g gas cookers then the room must have sufficient ventilation 14 Excessive fat accumulation in the kitchen hood and metal filters is a fire risk and may also cause dripping therefore the inside of the kitchen hood and the metal filters must be cleaned at least once a month The lower part of the kitchen hood must be fitted at least 50 cm over electric hobs and 65 cm over gas or mixed hobs Never leave gas hobs lit if not covered by a container The fat accumulated in the filters may drip or catch fire when the temperature increases Avoid cooking under the kitchen hood if the metal filters are not fitted e g while they are being cleaned in the dishwasher You must not produce flames under the kitchen hood Disconnect the appliance before any interior manipulation E g during cleaning or maintenance We recommend the use of gloves and to be extremely careful when cleaning the kitchen hood s interior Your kitchen hood is designed for domestic use and only for extraction and purification of fumes produced during food preparation It will be your responsibility if it is used for other purposes which may be dangerous The manufacturer cannot accept res2. 0 2x20 250 800 m h 216321ND 220 240 50 2x20 150 600 m h 234321ND 110 127 60 2x20 280 TEKA INDUSTRIAL S A reserves the right to make changes and corrections to its 730 m h products as it deems necessary without altering their basic characteristics o 17 ENG Manual ND qxd ENG 12 01 2005 17 10 Accesories supplied 150 125 mm reduction Anti recoil valve Support for tubecover Wall supports Screws M4x12 Wall plugs 98 x 40 Long bolts 95 x 45 Wall plugs G6 x 30 Long bolts 94 x 30 6 4 x 918 washers 6 4 x 912 washers Screws 83 9 x 13 Clips DN DNA FPO DO FN NY H Installation Fig 1 Page 19 On installing the kitchen hood make sure that the Safety Instructions set out on page 14 are complied with To obtain optimum performance the external duct must not be more than FOUR METRES LONG have no more than two 90 angles and its diameter must be at least 9120 1 Using the attached template trace and drill the points for fitting the wall plugs onto the wall P 18 x 40 and J 6 x 30 2 Attach the supports O to the wall using the long bolts Q 5x45 and the support H with the long bolts I 4x30 as in figure 1 3 Fit the support O to the body of the hood using the long bolts L M4 x 12 4 Trace the location of the wall plugs R 98 x 40 through the inside of the kitchen hood 5 Take the kitchen h
3. Manual ND qxd 12 01 2005 17 10 Page 1 F Manual de Instrucciones Campanas Extractoras ND 3 Bedienungsanleitung Dunstabzugshauben ND 3 Instructions Manual Kitchen Hoods ND 3 Manuel d instructions Hottes aspirantes ND 3 Manual de Instru es Exaustores ND 3 en a Manual ND qxd 12 01 2005 17 10 Page HE ENG Dear client Congratulations on your choice We are sure that this modern functional and practical appliance made with top quality materials will fully satisfy your needs Please read every section of this INSTRUCTIONS MANUAL before using your kitchen hood for the first time to ensure maximum performance from the appliance and to avoid breakdowns which may be caused by incorrect use as well as to allow any minor problems to be solved Store this manual as it will provide useful information about your kitchen hood at all times and will also help other people to use it Safety Instructions e Please be aware of current local regulations with reference to domestic electrical fittings and gas eduction Verify that the tension and frequency of the network match those indicated on the label located inside the kitchen hood e The appliance must be connected to the network using a break switch with a universal cut off and minimum contact separation of 3 mm Once the kitchen hood has been installed ensure that the mains cable to the network is not in contact with any live metal edges
4. n filters The active carbon filters have an active life of between three to six months depending on the individual conditions of use These filters cannot be washed nor regenerated They must be replaced once their useful life comes to an end SET type 1 Fig 3 Page 19 1 Put the filters into the lateral draught section of the motor making the holes in the filters match up A with the pivots B of the motor carcass Turn as indicated in the diagram 2 Remove the tubecovers E Fit the diffuser C on to the motor s air outlet vent Fit the tubecovers back on E o
5. ood off 6 Drill into the wall and fit the wall plugs R 88 x 40 7 Hang the kitchen hood tighten the screws M M4 x 12 with the washers A3 96 4 x 12 and the long bolts S 95 x 45 with the washers T 6 4 x 918 18 Page 18 F 8 Adjust the decorative part U fixing it softly to the body of the bell using the screws provided with the decorative part 9 Mount the tubecovers attaching the lower one to the support H as per the detail in figure 1 Lift the upper tubecover up to the desired height and mark its shape on the wall Remove the tubecovers 10 Fit the clips F to the support C 11 Centre the support C around the shape marked trace and drill the fixing points for the wall plugs E 26 x 30 Attach the support C with the long bolts D 4 x 30 12 Fit the part A if the inner tube not supplied is 9150 or A B if it is 120 13 Attach the inner tube with a clamp not supplied to A or B as the case may be 14 Once the inner tube has been fitted fit the lower tubecover around the extractor fan outlet and attach the upper tubecover with the screws G 83 9 x 13 15 Adjust the decorative part U fixing it tightly to the body of the bell using the screws provided with the decorative part When exterior gas extraction is not possible Active charcoal filters Optional then the kitchen hood may be set to purify the air by recycling it through active carbo
6. ough this will not affect its fat retention capacity Once clean leave them to dry off and then fit them onto the kitchen hood Changing light bulbs Proceed as follows Unscrew the lamp cap trimming cover e Change the broken burnt out Maximum lamp power is 20 W G 4 lamp Screw in the lamp cap trimming cover Problem solving Proceed with the following checks before calling Technical Services Problem Possible cause Solution The extractor fan does not work network There is no current in the network The kitchen hood does not extract sufficiently or vibrates Obstruction in the air exit conduct The lamps do not light up The lamps are blown The lamps are slack 16 The mains cable is not connected to the Filters are saturated with fat Connect mains cable to the network Provide current to the network Change or clean the active charcoal and or metal filters as the case may be Remove the obstruction Change the lamps Tighten the lamps Manual ND qxd 12 01 2005 17 10 Page Te Sizes and specifications e TOKO INDUSTRIAL S A SANTANDER E Campana decorativa Serial n A 00000 C digo T cnico VKATAXKETHI ELECT Potencia nom l mpara Pot ncia nom l mpada uissance lampes ES tate 2x20W max Technical Network Network Lights Motor code tension V frequency Hz power W Extraction capacit 214321ND 220 240 5
7. ponsibility for damage caused by improper use of the appliance For repairs please contact the nearest TEKA Technical Assistance Service and always use genuine spare parts Repairs or modifications carried out by unqualified personnel can cause malfunctions or may damage the appliance putting your safety in danger zz Manual ND qxd 12 01 2005 17 10 Page Ee Index Page Description of the appliance 15 Instructions for use 15 Programming timer 15 Cleaning and maintenance 16 Problem solving 16 Sizes and specifications 17 Accessories supplied 18 Installation 18 Active carbon filters 18 Description of the appliance A Electronic programmer control box with buttons to control speed light and power in use indicators B Metal filters C Lamp with two bulbs 20 W G 4 Vertically adjustable tubecovers F Decorative part Not incluided Instructions for use 30min 20min 10min 5min Light Minimum speed Medium speed Maximum speed Extra fan Timer Switch on the extractor fan a few minutes before you start to cook in order to ensure that a steady air flow has been established before fumes appear Allow the extractor fan to run for several minutes after you have finished cooking between 3 to 5 minutes in order to expel all the grease from the outlet duct This prevents the return of grease smoke and smells Programming timer 1 The draft hood will remain on for 10 minutes a
8. t the selected level if pressed at any speed for more than 2 seconds To programme a time other than the pre selected one 10 minutes a Press the Timer button with the draft hood turned off b Select the intake time by pressing the corresponding button see figure c Press the Timer button again d Press the chosen speed for more than 2 seconds and the light will begin to flash 15 ENG Manual ND qxd 12 01 2005 17 10 Page E ENG Cleaning and maintenance During cleaning and maintenance work make sure the safety instructions set out on page 14 are complied with Cleaning the hood body If your kitchen hood is made from stainless steel use proprietary cleaners mentioned in the product instructions Never use metallic scourers nor abrasive or corrosive products e Dry the kitchen hood using a cloth that does not produce fibres Cleaning the metal filters Extract the filters from their housings using the handles specially designed for this purpose The metal filters can be cleaned by soaking them in hot water with neutral detergent until the fat dissolves and then rinsing them under the tap or using special anti grease products They can also be washed in a dishwasher In this case it is advisable to stack them vertically to avoid food residues to stick to them Cleaning in a dishwasher with aggressive detergents or polish may damage the metallic surface blackening it alth
Download Pdf Manuals
Related Search