Teka DF-90 User's Manual
Contents
1. hood has been installed ensure that the mains cable to the network is not in contact with any live metal edges Avoid connecting the appliance to conductors used as exits for fumes produced by a non electric energy source e g boilers chimneys etc f the extractor fan is going to be used simultaneously with equipment powered by a non electric energy source e g gas cookers then the room must have sufficient ventilation Excessive fat accumulation in the kitchen hood and metal filters is a fire risk and may 10 also cause dripping therefore the inside of the kitchen hood and the metal filters must be cleaned at least once a month The lower part of the kitchen hood must be fitted at least 50 cm over electric hobs and 65 cm over gas or mixed hobs FOLLOW THE HOBS MANUFACTURER S MINIMUM RECOMMENDATIONS Never leave gas hobs lit if not covered by a container The fat accumulated in the filters may drip or catch fire when the temperature increases Avoid cooking under the kitchen hood if the metal filters are not fitted e g while they are being cleaned in the dishwasher You must not produce flames under the kitchen hood Disconnect the appliance before any interior manipulation e g during cleaning or maintenance We recommend the use of gloves and to be extremely careful when cleaning the kitchen hood s interior Your kitchen hood is designed for domestic use and only for extraction and purific2. 11 Se i C21141800 DF qgxd 18 4 05 12 24 P gina 12 d ENG Filter saturation indicators F Clean the filters when the saturation indicator lights up See page 12 Filter cleaning section Once you have cleaned the filters and with the hood turned off press the increase and decrease speed buttons at the same time for 3 seconds and the indicator will switch itself off Cleaning and maintenance During cleaning and maintenance work make sure the safety instructions set out on page 10 are complied with Cleaning the hood body e If your kitchen hood is made from stainless steel use proprietary cleaners mentioned in the product instructions Never use metallic scourers nor abrasive or corrosive products e Dry the kitchen hood using a cloth that does not produce fibres Cleaning the metal filters To remove the filters from their fittings press lightly on the locks and then pull them off The metal filters can be cleaned by soaking them in hot water with neutral detergent until the fat dissolves and then rinsing them under the tap or using special anti grease products They can also be washed in a dishwasher In this case it is advisable to stack them vertically to avoid food residues to stick to them Cleaning in a dishwasher may damage the metallic surface blackening it although this will not affect its fat retention capacity Once clean leave them to dry off and then fit them onto the kitche
3. C21141800 DF qxd 18 4 05 12 24 P gina 1 d Manual de Instrucciones Campanas Extractoras DF 90 Bedienungsanleitung Dunstabzugshauben DF 90 Instructions Manual Kitchen Hoods DF 90 Manuel d instructions Hottes aspirantes DF 90 Manual de Instruc es Exaustores DF 90 OAHT TEX XPHXEOX KAMINAAA TOIXOY DF 90 Kullanim Kilavuzu Davlumbaz DF 90 C21141800_DF qxd 18 4 05 12 24 P gina 10 c ENG Dear client Congratulations on your choice We are sure that this modern functional and practical appliance made with top quality materials will fully satisfy your needs Please read every section of this INSTRUCTIONS MANUAL before using your kitchen hood for the first time to ensure maximum performance from the appliance and to avoid breakdowns which may be caused by incorrect use as well as to allow any minor problems to be solved Store this manual as it will provide useful information about your kitchen hood at all times and will also help other people to use it Safety Instructions e Please be aware of current local regulations with reference to domestic electrical fittings and gas eduction Verify that the tension and frequency of the network match those indicated on the label located inside the kitchen hood The appliance must be connected to the network using a break switch with a universal cut off and minimum contact separation of 3 mm THE NET CABLE MUST NOT BE SUBTITUTED Once the kitchen
4. ONE FAX Austria Wien K PPERSBUSCH GES M B H 43 1 86680 0 1 86680 72 Belgium Zellik B V B A K PPERSBUSCH S P R L 32 2466 8740 2466 7687 Chile Santiago de Chile TEKA CHILE S A 56 2 273 19 45 2 273 10 88 China Shanghai TEKA CHINA LTD 86 21 6236 2375 21 6236 2379 Czech Republic Brno TEKA CZ S R O 42 05 4921 0478 05 4921 0479 France Saint Ouen l Aum ne TEKA FRANCE SAS 33 0820072747 0134301596 Greece Athens TEKA HELLAS A E 30 210 9760283 210 9712725 Hungary Budapest TEKA HUNGARY KFT 36 1 354 21 10 1 354 21 15 Indonesia Jakarta P T TEKA BUANA 62 21 39052 74 21 39052 79 Malaysia Kuala Lumpur TEKA K CHENTECHNIK MALAYSIA SDN BHD 60 3 762 001 600 3 762 01 626 Mexico Mexico D F TEKA MEXICANA S A DE C V 52 555 762 04 90 555 762 05 17 Poland Pruszk w TEKA POLSKA SP ZO O 48 22 738 32 80 22 7938 32 89 Portugal Ilhavo TEKA PORTUGUESA LTDA 351 234 32 95 00 234 32 54 57 Russia Moscow TEKA RUS LLC 7 095 737 4689 095 737 4690 Singapore Singapore TEKA SINGAPORE PTE LTD 65 6 73 42415 6 73 46881 Thailand Bangkok TEKA THAILAND CO LTD 66 2 5164954 2 9021484 The Netherlands Zoetermeer TEKA B V 31 79 345 15 89 79 345 15 84 Turkey Istanbul TEKA TEKNIK MUTFAK A S 90 212 274 61 04 212 274 56 86 U K Abingdon TEKA PRODUCTS UK LTD 44 1235 86 19 16 1235 83 51 07 U S A Tampa TEKA USA INC 1 800 419 9344 813 228 8604 Venezuela Caracas TEKA ANDINA S A 58 212 291 28 21 212 291 28 25 e CKO KUCHENTECHNIK Te
5. ake sure that the Safety Instructions set out on page 10 are complied with To obtain optimum performance the external conduct must not be more than FOUR METRES long have no more than two 90 angles and its diameter must be at least 120 1 Trace and drill the points for fitting the wall plugs onto the wall P 28 x 40 and J 26 x 30 2 Attach the Supports O to the wall using the long bolts Q Z5 x 45 and the support H with the long bolts I 04 x 30 as in figure 1 3 Hang the kitchen hood onto the mounted supports O Straighten the appliance by tightening the long bolts L M4 x 12 4 Remove the metal filters Loosen the screws without unscrewing them of the EASYCLEAN panels A19 move the panels aside carefully and take them off 5 Trace the location of the wall plugs R 28 x 40 through the inside of the kitchen hood 6 Take the kitchen hood off 7 Drill into the wall and fit the wall plugs R Q8 x 40 8 Hang the kitchen hood tighten the screws M M4 x 12 with the washers A3 26 4 x 912 and the long bolts S 5 x 45 with the C21141800_DF qxd 18 4 05 12 24 P gina 13 d washers T 26 4 x 18 9 Mount the EASYCLEAN panel again A19 Fit the metal filters 10 Mount the tubecovers attaching the lower one to the support H as per the detail in figure 1 Lift the upper tubecover up to the desired height and mark its shape on the wall Remove the tubecovers 11 Fit the clips F to
6. ation of fumes produced during food preparation It will be your responsibility if it is used for other purposes which may be dangerous The manufacturer cannot accept responsibility for damage caused by improper use of the appliance For repairs please contact the nearest TEKA Technical Assistance Service and always use genuine spare parts Repairs or modifications carried out by unqualified personnel can cause malfunctions or may damage the appliance putting your safety in danger This appliance is marked according to the European directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE This guideline is the frame of a European wide validity of return and recycling on Waste Electrical and Electronic Equipment X C21141800 DF qxd 18 4 05 12 24 P gina 11 d Index Instructions for use You may control the kitchen hood by operating the controls as shown in the diagram Page Description of the appliance 11 oxXooQ0 i 820004060 Instructions for use 11 o 9X EI Program display Filter saturation Cleaning and maintenance 12 Tm Problem solving 12 3e Light Sizes and specifications 12 Reduce speed Accessories supplied 13 E bee O Onoff Installation 13 m 3 R Power display Automatic mode Active charcoal filters 13 Switch on the extractor fan a few minutes before you start to cook in order to ensure that a steady air Description of the appliance flow has been estab
7. ent Fit the tubecovers back on E 13 e zm lu C21141800 DF qxd 18 4 05 12 24 P gina 30 d CAMPANA DECORATIVA Teka a ed TEKA INDUSTRIAL S A ire bes SANTANDER E No KATAEKETHE ELECT POTENCIA N M LAMPARAS POTENCIA NOMINAL DAS LAMPADAS MEFTETH ONOMALTH at 220 230 2 x 20 250 CD Lo mos 60 2x20270 720 m h Ver Placa de Caracter sticas en el interior de la campana ae mamo o raso 820 mh Siehe Typenschild im Innern der Dunstabzughauben LL 22 20 so 2x20 250 820 m h a EE 720 mi h Check Characteristics label inside the hood LL 220 230 220 250 820 m h Voir Plaque des Caract ristiques l int rieur de la hotte E EE 2 x 20 250 820 m h V r Placa de caracter sticas no interior do exhaustor Tegyik s Ko ik z T cr Aucr ov V Evyv rgra Awucr ov Hz Ioy c D roc Mor p W Az ocr Mor p E 220 230 50 2 x 20 250 820 m h Ed y te mm Tou io Teyvik v Xapaxtnpiotikov ca otov azoppognujpa Teknik Kodu Hat Gerilimi V Hat Frekansi Hz Isik Motor G c W Cekis G c 2x20 250 B20 mh Cihaz n zerindeki teknik zellikler etiketini kontrol ediniz 30 B Ea C21141800 DF qxd 18 4 05 12 24 P gina 31 d SS 7 esas C21141800 DF gxd 18 4 05 12 24 P gina 32 c TEKA GROUP COUNTRY CITY COMPANY CC PH
8. ka Kuchentechnik GmbH Sechsheldener Str 122 35708 Haiger Germany Tel 49 2771 8141 0 Fax 49 2771 8141 10 http www teka net Teka Industrial S A Cajo 17 39011 Santander Spain Tel 34 942 35 50 50 Fax 34 942 34 76 94 http www teka net Mod 4 869 Gr ficas Alhambra JKP 06 03
9. lished before fumes appear Allow the extractor fan to run for several minutes A Electronic proarammer control box after you have finished cooking between 3 to 5 ith butt i 9 trol d light and minutes in order to expel all the grease from the w u ans EH ro Speed Mght an outlet duct This prevents the return of grease power in use indicators DISPLAY smoke and smells T B Metal filters Automatic functioning mode A Z c Lamps 20 W G 4 The cooker hood will work automatically in the first 3 speeds according to the humidity level detected and will turn off automatically when humidity stops F Decorative part In order to take off the automatic mode manually select a speed or turn off the cooker hood The automatic mode will restore again when the cooker hood does not work and no humidity is detected D E Vertically adjustable tubecovers Programming timer Proceed as follows 1 Turn the kitchen hood on and choose the required speed 2 Press timer The Program DISPLAY will flash 3 Select the required time by pressing the increase and decrease speed selectors There is a variation of 5 in 5 minutes Min 5 min Max 45 min 4 Once the required time has been selected press timer again to memorise the program 5 The kitchen hood will turn itself off once the programed time has finished The intensive speed H can only be selected manually and will change to speed 2 after approximately 10 minutes
10. n hood Changing light bulbs Proceed as follows Unscrew the lamp cap trimming cover Change the broken burnt out lamp Maximum lamp power is 20 W G 4 Screwin the lamp cap trimming cover Problem solving Proceed with the following checks before calling the Technical Service Problem The extractor fan does not work network There is no current in the network The kitchen hood does not extract sufficiently or vibrates Obstruction in the air exit conduct The lamps are blown The lamps do not light up The lamps are slack Filters are saturated with fat Possible cause Solution The mains cable is not connected to the Connect mains cable to the network Provide current to the network Change or clean the active charcoal and or metal filters as the case may be Remove the obstruction Change the lamps Tighten the lamps Sizes and specifications See page 30 TEKA INDUSTRIAL S A reserves the right to make changes and corrections to its products as it deems necessary without altering their basic characteristics 12 Accesories supplied 150 120 mm reduction Support for tubecover Wall support Wall plugs 28 x 40 Long bolts 05 x 45 Wall plugs 6 x 30 Long bolts 94 x 30 6 4 x 018 washers 06 4 x O12 washers Screws 23 9 x 13 Screws O4 x 12 Clips m SM MM SF o o MM ch Installation Fig 1 Page 31 On installing the kitchen hood m
11. the support C 12 Centre the support C around the shape marked trace and drill the fixing points for the wall plugs E 26 x 30 Attach the support C with the long bolts D 24 x 30 13 Fit the part B if the inner tube not supplied is 9120 14 Attach the inner tube with a clamp not supplied to B or on to the motor s air outlet vent as the case may be 15 Once the inner tube is fitted fit the lower tubecover around the extractor fan outlet and attach the upper tubecover with the screws G 03 9 x 13 Active charcoal filters Optional When exterior gas extraction is not possible then the kitchen hood may be set to purify the air by recycling it through active charcoal filters The active charcoal filters have an active life of between three to six months depending on the individual conditions of use These filters cannot be washed nor regenerated They must be replaced once their useful life comes to an end Fig 2 Page 31 1 Remove the metal filters Loosen the screws without unscrewing them of the EASYCLEAN panels K move the panels aside carefully and take them off 2 Put the filters into the lateral draught section of the motor making the holes in the filters match up A with the pivots B of the motor carcass Turn as indicated in the diagram 3 Mount the EASYCLEAN panel again K Fit the metal filters 4 Remove the tubecovers E Fit the diffuser C on to the motor s air outlet v
Download Pdf Manuals
Related Search