Teka CS-6000 User's Manual
Contents
1. Assembly Instructions and maintenance recommendations Cooker Hoods CS 6000Using this instruction book Montageanleitung und Pflegehinweise Dunstabzugshauben CS 6000 Instructions d installation et recommandations d entretien Hottes aspirantes CS 6000 Safety instructions Dear Customer Thank you for choosing our cooker hood We are sure that appliance you have acquired will fully satisfy all your needs This model is made using top quality materials and undergoes rigorous testing throughout the manufacturing process Read this manual carefully before installing or using the product and faithfully follow the ins tructions in order to guarantee optimal perfor mance of the appliance for many years Keep this instruction book in a safe place so that you can consult it whenever necessary and fulfil guarantee requirements Before using your hood for the first time plea se take note of the installation and connection instructions Never unplug your hood by pulling the power cable always by removing the plug from the socket Never switch the hood on if the electrical feed cable is in a state of disrepair or is cut or if the appliance shows visible signs of wear on the part where the controls are found If the hood stops working or works abnormally disconnect it from the mains unplug and inform the Technical Assistance Service Do not leave gas burners turned on under the hood without their2. NG e Never use metallic scourers e Do not use abrasive products that may damage the metallic surface e Do not scratch with hard objects such as knives scissors etc Carbon filter The activated carbon filter cannot be washed or regenerated Once it has become soiled obstructed it must be replaced A Cleaning the grill and ventilator Wait for the motor to cool before carrying out this operation e Remove the screw that holds the grill to the support e Turn the grill in an anticlockwise direc tion e Using a pair of pliers situate the ventila tor bolt over the axle e Clean the grill and ventilator and then dry them e To fit the ventilator place the axle in the bolt as far as it will go and then press it in Fit the grill by turning it clockwise WARNING The hood should never be switched on without the grill Non compliance with this warning shall be the sole responsibility of the user when faced with a damaged appliance Changing the light bulbs Remove the filter support to access the light bulbs B Make sure that the hood has previously been disconnected from the mains supply and that the bulbs to be replaced are not hot The maximum bulb power is 40 W If something doesn t work Before calling the repairs service make the following checks Technical information Fault Possible causeSolution The hood doesn t work Mains cable not conne
3. being covered by a recipient such as a pot or pan Do not allow grease to build up on any part of the hood especially on the filter TO DO SO WOULD CONSTITUTE A FIRE HAZARD Do not flamb food underneath the hood ndex Description of the appliance Special requirements before use for the first time How to use the appliance Motors Light switches Suggestions and recommendations Cleaning and maintenance Cleaning the filter Cleaning the filter support and the hood body Carbon filter Grill and ventilator cleaning Changing the light bulbs If something does not work Technical Information Installation Upper Outlet Re circulation through activated carbon Changing the mains cable page 4 o O O 0 10 11 12 14 14 15 Description of the appliance These hoods are fitted with A B c 7 H amp l J amp K Light switch Sliding three speed motor control switch Operation indicator light Controllable visor that enables better smoke collection gases Filter body and supports Filter support closures Light bulb illumination over the coo king area and set behind a light diffu ser Easily extractable filter fitted in the lower part of the suction surface optional Anti return fins H included in the bag with the appliance documenta tion These are fitted a at the mouth of the outlet with their ends fitted in the holes prepared to h
4. cted Connect mains cable Power not reaching plug Check repair mains supply MOD CS 6000 TYP S 622325 Hood not extracting sufficiently or vibrating N de fabric Fabrik Nr Serial N Made in European Community C I F A 39004932 89 555551 LAMPS RATE Filter saturated with grease Obstruction in venting duct Clean or replace filter PUISSANCE LAMPES POTENCIA NOM LAMPARAS NENLEISTUNG GLUHLAMPEN POTENCIA NOM DAS LAMPADAS ELECT 220 230 V 50 Hz N 190 W Remove obstruction Inadequate venting duct Contact installer and follow the instructions in this manual Lights do not work Bulbs blown Replace bulbs Bulbs loose Tighten up bulbs 10 Dimensions mm Voltage Frequency Maximum load 600 900 x 500 x 150 Width x length x height SEE CHARACTERISTICS LABEL 11 Installation Before installing the hood consult the require ments of the appropriate authorities concer ning air and smoke extraction regulations Extracted air must not be channelled through ducts used for exhaust fumes from appliances powered by any form of energy other than elec tricity The room kitchen must be well ventilated if the extractor hood is to be used at the same time as other extractor fans or other applian ces powered by any form of energy other than electricity When the hood is to operate a
5. de breaking the lower thickness plastic area that has been prepared for cases like this and cutting off any remaining burrs 15
6. n lt lt E gt gt situated in the casing An outlet tube non return is fitted checking to ensure that the other outlets are duly cove red Re circulation through active carbon Place the lever situated in the casing in the position lt lt I gt gt ensuring that the round cover is placed over the opening A The active carbon filter is then placed in the suction mouth If the kitchen is fitted with furnishings such as wall cupboards the hood may be placed directly underneath them by using the set that is drawn on the following page If gas extraction is required through the hood s upper outlet A then a sufficiently large orifi ce should be left for the gas outlet pipe to be fitted ttt ttt cL att tit att 14 Replacing the mains cable e Ensure that the hood is disconnected from the mains supply e Open the electrical connections box removing the screws securing its cover and release the mains cable safety retai ner e Loosen the screws on the terminals mar ked N Land remove the four screws which secure the intermediate unit to the chassis and guide the new cable to the drillhole in the connections box connec ting the blue wire to the N terminal and the brown wire to the L terminal If the external cable is of a diameter greater than the one supplied entry to the connection box is achieved by pressing its si
7. n order to ensure that a steady air flow has been establis hed before cooking fumes appear Allow the extractor fan to run for several minutes after you have finis hed cooking 3 to 5 minutes in order to expel all the grease from the outlet duct This prevents the return of grease smoke and smells Cleaning and maintenance BIFORE CLEANING AND MAINTENANCE BE SURE THAT THE APPLIANCE IS DISCONNEC TED FROM THE MAINS SUPPLI Limpieza del Filtro e Open the filter support by moving the closures Remove the support take special care to avoid dropping it e Remove the filter by pulling it out and pro ceed with cleaning either in a dishwasher or leaving it under hot running water clea ning it with a non abrasive brush e It should be dried once cleaning is completed NOTE Cleaning in a dishwasher with strong detergents may darken the metallic surface without affecting its grease retaining perfor mance WARNING Filter cleaning should be carried out at least once a month depending on the extent of hood use It should be remembered that grease accu mulates in the hood and in the filters even though it is not switched on Cleaning the filter support and the hood body e Soapy water at a temperature of about 40 C is recommended A damp cloth is used with this water for cleaning the hood paying particular attention to crevices It should then be dried using a dry cloth that does not leave any fibres WARNI
8. ouse them l Grill and ventilator that can be remo ved for cleaning O02000 cs 6000 The hood in designed in the evacuation of gases to the outside or for his movement thrugh carbon filter The allow that gases can retum to the kitchen purified For place the carbon filter the anchorage of motor must coincide with the anchorage of carbon filter and we fix in turning it in the sen se of the hands of the clock Life of de carbon filter is theree to six months depending on particuler conditions of use To replace old filters we do it in reverse sense to the instalation Special Requirements befo re using for the first time Before connecting the hood to the electricity mains make sure that the mains voltage and frequency correspond to the values indicated on the rating plate inside the hood How to use the appliance Motors Use the controls on the frontal part switching them to the required suction speed The hood motor has three speeds and a pilot to indicate operation of any of them 3 20 10 00 SS ee a ae Off position First speed Second speed Third speed WNPS Light switch This is independent of the motor This enables the lights to be used regardless of whether the hood is in use Suggestions and recommendations Switch on the extractor fan a few minutes before you start to cook 3 to 5 minutes i
9. t the same time as other appliances powered by any form of energy other than electricity the air output pressure must not be more than 4 Pa 4 x 10 5 bar To ensure optimum hood performance the length of the venting duct should not exceed four metres and should not have more than two right angles 90 If the hood is supplied without a plug for mains connection or if this is replaced it must be disconnected from the mains by means of an omnipolar cut off switch with a minimum contact separation of 3 mm at all the poles incorporated into the fixed installation The installation connection should be carried out using flexible wire It must not be done using a rigid tube The hood should be connected to an earthed electrical installation 12 The lower part of the hood should be placed at a minimum height of 60 cm above the hob for electric cookers and 70 cm for gas coo kers Although it is recommended that gases be extracted to the exterior active carbon filters may be installed This enables the gases to return to the kitchen through the outlet Opening for the outlet fumes 98 173 TEMPLATE FOR ASSEMBLY UNDER FORNITURE Upper edge of the hood lean on the wall TEMPLATE FOR ASSEMBLY ON THE WALL 13 Extraction through the upper part A The system requires an outlet conduit The gas extraction lever should be set in the positio
Download Pdf Manuals
Related Search