Targus 400-0086-001A User's Manual
Contents
1. TARGUS Essential Accessories for Mobile Computing Wireless 5 Button Scroller Optical Mini Mouse TARGUS Essential Accessories for Mobile Computing USER S GUIDE Making Your Mobile Life Easier Making Your Mobile Life Easier Visit our Web site at www targus com Features and specifications are subject to change without notice 2002 Targus Corp 400 0086 0014 BrRusseLs HAannoveR BAaRceLona Tokyo MIiLaNno AMSTERDAM SINGAPORE LonDpon PaRi s NewYork Los AnGceLes Toronto Honc Kone SYDNEY PMS Black 100 PMS Black 15 Wireless 5 Button Scroller Optical Mini Mouse Introduction Congratulations on your purchase of the Targus Wireless 5 Button Scroller Optical Mini Mouse This ergonomically designed mouse uses a radio frequency RF link that enables you to use the mouse anywhere within 4 5 feet of its receiver No line of sight between the mouse and its receiver is required The optical mouse also provides a scrolling wheel and three user programmable buttons for multimedia use In addition to this user s guide this package contains e Wireless 5 Button Scroller Optical Mini Mouse e Receiver e AA NiMH rechargeable battery e Three inch USB extension cable e Charger base e AC power adapter e Device driver software CD ROM System Requirements To use the optical mouse your computer must meet the following hardware requirements and run one of the operating systems listed below H2. and 2 This device must accept any interference received including interference that may cause undesired operation FCC Statement Tested to Comply This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Move the computer away from the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Microsoft IntelliMouse Windows and Windows NT are registered trademarks of Microsoft Corporation All other trademarks are the property of their respective owners 15
3. for the pointer The Snap to default feature allows you to assign the pointer to jump to default buttons in dialog boxes Hardware Tab Selecting the Hardware tab displays general information about the Wireless 5 Button Scroller Optical Mini Mouse Wheel Tab The Scrolling Mode option allows you to choose between the Intelli Mouse Compatible Mode and the Enhanced Scroll Mode e Intelli Mouse Compatible Mode enabling this mode simulates Microsoft IntelliMouse and supports features used with Microsoft applications such as zoom scrolling and Auto scrolling e Enhanced Scroll Mode this mode supports all applications that use scroll bars with zoom Auto panning and scrolling functions The Scrolling Settings option allows you to adjust how many lines of text will scroll and the direction of the scroll movement Button Assignment Tab Mouse Properties 24x Buttons Pointers Motion Hardware Wheel Button Assignment Third Button 3rd r N 3 Auto Scroll x Setting a N Fourth Button 4th Page Back Default ha Setting Fifth Button 5th Page Forward Default x Setting Cancel Apply Mouse Properties screen Button Assignment tab The Button Assignment feature allows you to assign frequently used mouse and keyboard functions such as Auto Scroll Page Back and Page Forward to the third fourth and fifth mouse buttons To do this 1 Click the drop down arr
4. of the mouse by pressing the battery cover tab and siding it off 2 Insert the supplied battery making sure that the positive and negative end of the battery match the polarity indicators inside the battery housing 3 Slide the battery cover back into position until it clicks firmly into place The optical sensor located on the bottom of the mouse glows red WARNINGS When replacing the battery if you are using the mouse with the charger base you must use heavy duty NiMH rechargeable batteries to avoid possible damage to the mouse and charger If you are using the mouse without the charger base you may use alkaline or other heavy duty NiMH batteries Setting the Radio Frequency Channel Before you establish a link between the optical mouse and its receiver you must set the radio frequency channel To do this slide the channel switch to A or B on both the mouse and the receiver For the mouse the switch is located inside the battery compartment For the receiver the switch is located directly opposite the USB connector NOTE The optical mouse and its receiver must be set to the same channel to function properly Establishing a Communications Link The optical mouse has 256 identification codes that allow the mouse and its receiver to operate without interference from other radio frequency devices To set the identification code and establish a radio link between the mouse and the receiver 1 Press an
5. tendons and muscles may be related to repetitive motion an improperly set up work area incorrect body posture and poor work habits To reduce the risk of injury follow these precautions Stand stretch and move around several times every hour Switch hands while performing tasks Use shortcut keys to avoid repetitive or awkward mouse movements Relax your shoulders and keep your elbows at your sides Adjust the keyboard s position so that you don t have to stretch to reach it Adjust your position so that you don t have to bend your wrists to type avoid placing your wrists on a sharp edge If you feel discomfort or numbness in your hands wrists arms shoulders neck or back while typing consult a qualified medical professional Specifications Mouse Carrier Frequency 27 MHz Dimensions Mouse 4 8 x 2 64 x 1 6 inches 122 x 67 x 40 mm Receiver 2 48 x 0 86 x 0 66 inches 63 x 22 x 17 mm NOTE Receiver dimensions do not include the extended USB connector Weight Mouse 4 1 ounces without battery 116 grams Receiver 98 ounces 28 grams 10 Receiver Interface USB version 1 1 Operating Voltage Mouse 1 2V DC powered by a battery Receiver 5V DC powered by the USB port Battery 1 AA NiMH rechargeable Electromagnetic Characteristics EMC CE Type acceptance ETS 300 220 short range devices Distance Between Mouse and Receiver Up to 3 feet 1 m Operating Current Mouse 35 45 m
6. 49 0 21 16 579 1151 Italy 39 024 827 1151 Netherlands 31 053 484 9470 Spain 34 091 745 6221 Sweden 46 0 8 751 4058 Switzerland 41 0 1 212 0007 United Kingdom 44 0 20 7744 0330 Eastern Europe amp others 31 053 484 9479 Product Registration For more efficient customer service and to activate the product s warranty Targus recommends that you register your Targus accessory shortly after purchasing it To register your Targus accessory go to http www targus com registration asp You will need to provide your full name email address phone number and company information if applicable Warranty Targus warrants this product to be free from defects in materials and workmanship for one year If your Targus accessory is found to be defective within that time we will promptly repair or replace it This warranty does not cover accidental damage wear and tear or consequential or incidental loss Under no conditions is Targus liable for loss of or damage to a computer nor loss of or damage to programs records or data nor any consequential or incidental damages even if Targus has been informed of their possibility This warranty does not affect your statutory rights 14 Warranty Registration at http www targus com registration asp Regulatory Compliance This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference
7. A maximum Receiver 30 mA typically 100 mA maximum Mouse Standby Current 10 mA or lower Mouse Sleep Mode Current Below 5 uA Modulation Type FSK Transmission Rate 4 Kbps Error Detection 8 bit CRC 11 Troubleshooting What do I do if the optical mouse does not work Check that the channel setting on both the mouse and the receiver are the same Make sure that the polarity of the battery is correct The positive and negative ends of the battery must match the positive and negative connections in the battery housing The battery may need recharging Connect the mouse to the charger base Check that the receiver s USB connector is firmly attached to the USB port on your computer Verify that the device drivers are installed Make sure you have established a radio link between the mouse and its receiver See Establishing a Communications Link on page 6 When I use the optical mouse other wireless devices work more slowly or fail temporarily what should I do The mouse may cause interference with any cordless radio based device that operates at 27 MHz such as a telephone baby monitor or toy To reduce interference move the mouse s receiver and the base unit of the affected device as far away from each other as possible What do I do if the response time of the optical mouse is slow or the mouse intermittently stops working Increase the distance between the mouse s rec
8. ardware Operating System e PC with a Pentium processor or Windows 95 98 Me 2000 equivalent and a hard disk drive XP and Windows NT 4 0 e USB version 1 1 interface Connecting the Mouse Receiver To connect the mouse receiver 1 Turn off your computer 2 Plug the standard USB end of the cable into an available USB port on your computer You are now ready to install the device drivers for your operating system Installing the Device Drivers NOTE You must install the supplied device drivers to use the fourth and fifth buttons Otherwise the mouse will function as a standard three button mouse To install the supplied device driver Turn on your computer 2 Insert the driver software CD into your computer s CD ROM drive 3 Click Start Run then enter D Setup exe where D is the path of your CD ROM drive and then click OK The Welcome screen appears Click Next Select Typical or Custom installation and then click Next Click Yes Click Finish to complete the driver installation and restart your computer NY A Nn RA Once your computer restarts the mouse icon appears in the system tray You are now ready to install the battery in the mouse set the radio frequency channel and establish a communications link between the mouse and its receiver See Establishing a Communications Link on page 6 4 Using the RF Mouse Installing the Battery 1 Remove the battery cover from the bottom
9. d release the link button located on the bottom of the optical mouse 2 Press and release the link button on the receiver The receiver s status light flashes while it scans the identification codes for the mouse Once a code is selected the status light stops flashing 3 Press and release the screen scroller middle button You are now ready to use the optical mouse NOTE You must reestablish the communications link every time you change the batteries Personalizing the Mouse Features You can assign functions to the third fourth and fifth mouse buttons and control cursor movement by personalizing the mouse features from the Mouse Properties screen To do this 1 Click Start Settings and Control Panel 2 Double click the Mouse icon The Mouse Properties screen appears This screen has six tabs with options for selecting and controlling mouse features Buttons Tab The Button configuration feature allows you to assign the primary mouse button for right or left handed use The Files and Folders option allows you to assign the number of clicks that are required to open an item The Double click speed option adjusts how fast you have to click the mouse button to register a double click Pointers Tab This tab allows you to choose how the mouse pointer looks on the screen Motion Tab The Speed option adjusts the speed at which the pointer moves across the screen The Acceleration option adjusts the acceleration rate
10. eiver and the rest of your computer equipment Use the USB extension cable if necessary 12 e Increase the distance between the mouse s receiver and the base units of other wireless devices Turn off any wireless devices and their base units that are near the mouse s receiver If you are using the optical mouse on a metal surface move it and the receiver to a non metal surface Metals such as iron aluminum or copper shield the radio frequency transmission and may slow down the mouse s response time or cause the mouse to fail temporarily I can t use the optical mouse while another RF mouse is in use what should I do Change the channel selection A B on both the mouse and its receiver If this does not work reset the identification code See Establishing a Communications Link on page 6 Technical Support In the unlikely event that you encounter a problem with your Targus accessory please contact our technical support team at Email techsupport targus com Internet http www targus com support asp Our knowledgeable staff is also available to answer your questions through one of the following telephone numbers US Monday through Friday 8 00 a m 08 00 to 8 00 p m 20 00 Eastern time 800 283 6325 Canada Monday through Friday 9 00 a m 09 00 to 5 00 p m 17 00 Eastern time 888 827 4877 13 Europe Belgium 32 002 717 2451 Denmark 45 0 35 25 8751 France 33 0 1 64 53 9151 Germany
11. ow next to the button number you want to assign The functions list appears 2 Select the function you want to associate with the selected button 3 Click Apply Repeat for each button you want to assign a function to 8 Operating Hints For optimal performance and RF reception Place the receiver at least 8 inches 20 cm away from all electrical devices such as your monitor speakers or external storage devices Avoid using the optical mouse on a metal surface Metals such as iron aluminum or copper shield the radio frequency transmission and may slow down the mouse s response time or cause the mouse to fail temporarily The optical mouse will enter a suspend mode at the same time your computer does To wake the mouse press and release the screen scroller middle button If your computer has a metal case that contains aluminum or magnesium use the optical mouse to the side The display panel may interfere with the radio frequency signal if you use the mouse directly in front of the computer Never use the optical mouse on a glass or mirrored surface as these surfaces will cause the mouse to fail temporarily To maximize battery life use the optical mouse on a white or light colored surface Dark surfaces cause the mouse s light emitter diode LED light to glow brighter which causes the battery to discharge more rapidly Comfortable Usage Research suggests that physical discomfort and injury to nerves
Download Pdf Manuals
Related Search