Tanaka TED-210 User's Manual
Contents
1. This setting is the WA type carburetor only when the unit is installed NARNING When the engine is idling the bit must under no circumstances rotate NOTE FOR THE US MARKET Fig 3 1C We would like to inform that the power drills TED 262L R HS of the US model which carry the following label on the unit are different from the ones for other market in carburetor adjustment Adjustment of Standard openings of L H screws are not necessary www tanaka usa com 8 Finale NT AAKA Kart d Bet ENGINE CONFORMS 995 Ma Wee EMISSION REGULATIONS LY irse XXXXXXXXXXXX XXXX REFER TO OWNER S MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS D Fig 3 1C contacttanaka tanaka ism com TED 210 TED 262L R DH HS Owner s Manual TED 210 Fig 3 2B Air filter Fig 3 2 2B The air filter must be cleaned from dust and dirt in order to avoid e Carburetor malfunctions e Starting problems e Engine power reduction e Unnecessary wear on the engine parts e Abnormal fuel consumption Clean the air filter daily or more often if working in exceptionally dusty areas Cleaning the air filter Remove the air filter cover and the filter Rinse it in warm soap suds Check that the filter is dry before reassembly An air filter that has been used for some time cannot be cleaned completely therefore it must regularly be replaced by a new one A damaged filter must always be replaced NOTE TED 210 Saturate the2. Replace damaged parts Check for fuel leaks and make sure all fasteners are in place and securely fastened Replace parts that are cracked chipped or damaged in any way before using the tool Keep others away when making carburetor adjustments Use only accessories as recommended for this tools by the manufacturer N WARNING Never modify the tool in any way Do not use your drilling tool for any job except that for which it is intended Fuel safety Mix and pour fuel outdoors and where there are no sparks or flames Use a container approved for fuel Do not smoke or allow smoking near fuel or the tool or while using the tool Wipe up all fuel spills before starting engine Move at least 3 m 10 ft away from fueling site before starting engine Stop engine before removing fuel cap Empty the fuel tank before storing the tool Tt is recommended that the fuel be emptied after each use If fuel is left in the tank store so fuel will not leak Store tool and fuel in area where fuel vapors cannot reach sparks or open flames from water heaters electric motors or switches furnaces etc N WARNING www tanaka usa com Antivibration systems do not guarantee that you will not sustain whitefinger disease or carpal tunnel syndrome Therefore continual and regular users should monitor closely the condition of their hands and fingers If any of the above symptoms appear seek medical advice immediately TED 210 TE
3. Lock Control Oe eee ee TRAITER EE TED 262L Q Q R Sound pressure level dB A en 91 9 105 0 103 3 113 4 111 6 Vibration level m s Front handle srasteshetcoenutbttul ett dssethtKrtataussues ransesas 2 7 5 5 Right 9 9 Rear handle T ILC 3 9 4 9 Left 9 8 NOTE Equivalent noise level vibration level are calculated as the time weighted energy total for noise vibration levels under various working conditions with the following time distribution 2 idle 2 full speed All data subject to change without notice www tanaka usa com 12 contacttanaka tanaka ism com TED 210 TED 262L R DH HS Owner s Manual Declaration of conformity D claration de conformit Dichiarazione di conformita Konformitatserklarung Declaraci n de conformidad Konformitetsdeklaration We Tanaka Kogyo Co Ltd 3 4 29 Tsudanuma Narashino Chiba Japan Nous soussign s Noi Der unterzeichnete Nosotros Vi Declare under our sole responsibility that the product engine drill model TED 210 TED 262L R DH D clarons sous notre seule responsabilit que le produit en question perceuse mod le Dichiariamo sotto la nostra unica responsabilit che il prodotto il mototrapano modello Erklart unter eigener Verantwortung daB das Produkt bohrmaschine modell Declaramos dajo nuestra nica responsabilidad que el producto motorborrmaskin modelo F rklarar harmed pa eget ansvar att denna produkt taladro motorizado modell to which t
4. instructions that apply to your unit d 2 TED 210 TED 262L R DH HS Owner s Manual Handle Plug cap Ignition Switch Muffler Chuck unit Throttle trigger Recoil starter Gear case Fuel tank cap 10 Fuel tank 11 Shift lever 12 Air cleaner 13 Hole for strap po ee ON Ie TED 262L HS TED 262R TED 262DH www tanaka usa com 2 contacttanaka tanaka ism com D j j f T i r i f I j j ij j 2 Warnings and safety instructions Operator safety Always wear a safety face shield or goggles Always wear heavy long pants boots and gloves Do not wear loose clothing jewelry short pants sandals or go barefoot Secure hair so it is above shoulder length Do not operate that tool when you are tired ill or under the influence of alcohol drugs or medication Never let a child or inexperienced person operate the machine Wear hearing protection Never start or run the engine inside a closed room or building Breathing exhaust fumes can kill Keep handles free of oil and fuel Keep hands away from drilling equipment Do not grab or hold the unit by the drilling equipment When the unit is turned off make sure the drilling attachment has stopped before the unit is set down When operation is prolonged take a break from time to time so that you may avoid possible whitefinger disease which is caused by vibration Tool safety Inspect the entire tool before each use
5. element in 2 cycle oil or the equivalent Squeeze the element to distribute the oil completely and to remove any excess oil Spark plug Fig 3 3 The spark plug condition is influenced by e An incorrect carburetor setting e Wrong fuel mixture too much oil in the gasoline e A dirty air filter e Hard running conditions such as cold weather These factors cause deposits on the spark plug electrodes which may result in malfunction and starting difficulties If the engine is low on power difficult to start or runs poorly at idling speed always check the spark plug first If the spark plug is dirty clean it and check the electrode gap Readjust if necessary The correct gap is 0 6 mm 024 The spark plug should be replaced after about 100 operation hours or earlier if the electrodes are badly eroded Fig 3 3 NOTE In some areas local law requires using a resistor spark plug to suppress ignition signals If this machine was originally equipped with resistor spark plug use same type of spark plug for replacement www tanaka usa com 9 contacttanaka tanaka ism com TED 210 TED 262L R DH HS Owner s Manual Fig 3 4 Fig 3 4B Flg 3 5 Fuel filter Fig 3 5 Gear case Fig 3 4 4B Remove the fuel filter from the fuel tank and inspect Apply a good quality lithium based grease through the Replace with new filter if damaged or soiled Replace grease fitting Lubrication should be applied at 50 hour with new filter if
6. D 262L R DH HS Owner s Manual Drilling safety Do not drill any material other than that for which is intended Inspect the area to be drilled before each use Remove objects which can be thrown or become entangled For respiratory protection wear an aerosol protection mask when drilling the area after insecticide is scattered Keep others including children animals bystanders and helpers outside the 5 m 17 ft hazard zone Stop the engine immediately if you are approached Hold the tool firmly with both hands Keep firm footing and balance Do not over reach Keep all parts of your body away from the muffler and drilling attachment when the engine is running Maintenance safety Maintain the tool according to recommended procedures Disconnect the spark plug before performing maintenance except for carburetor adjustments Keep others away when making carburetor adjustments Use only genuine replacement parts as recommended by the manufacturer Transport and storage Carry the tool by hand with the engine stopped and the muffler away from your body Allow the engine to cool empty the fuel tank and secure the tool before storing or transporting in a vehicle Empty the fuel tank before storing the tool It is recommended that the fuel be emptied after each use If fuel is left in the tank store so fuel will not leak Store tool out of the reach of children Clean the unit carefully and store it in a dry place M
7. aka ism com TED 210 TED 262L R DH HS Maintenance Fig 3 1 Owner s Manual Fig 3 1B MAINTENANCE REPLACEMENT OR REPAIR OF THE EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY ANY NONROAD ENGINE REPAIR ESTABLISHMENT OR INDIVIDUAL Carburetor adjustment Fig 3 1 1 B NWARNING The bit may be spinning during carburetor adjustments NWARNING Never start the engine without the complete clutch cover and gear case assembled Otherwise the clutch can come loose and cause personal injuries In the carburetor fuel is mixed with air When the engine is test run at the factory the carburetor is basically adjusted A further adjustment may be required according to climate and altitude The carburetor has one adjustment possibility T Idle speed adjustment screw Idle speed adjustment T Check that the air filter is clean When the idle speed is correct the bit will not rotate If adjustment is required close clockwise the T screw with the engine running until the bit starts to rotate Open counter clockwise the screw until the bit stops You have reached the correct idle speed when the engine runs smoothly in all positions well below the rpm when the bit starts to rotate If the bit still rotates after idle speed adjustment contact your service workshop NOTE The standard openings returns of L H screws from lightly seated positions are as follows nmt TED 262L R DH LSCREW OL
8. ake sure engine switch is off when transporting or storing When transporting in a vehicle cover bit with bit cover or rug If situations occur which are not covered in this manual take care and have good judgement Contact your dealer if you need assistance Pay special attention to statements preceded by the following words CAUTION Indicates a possibility of personal injury or equipment damage if instructions are not followed NOTE Helpful information for correct function and use WARNING Indicates a strong possibility of severe personal injury or loss of life if instructions are not followed contacttanaka tanaka ism com TED 210 TED 262L R DH HS Owner s Manual Fig 1 1 Fig 1 1B Fig 1 1C Assembly procedures Assembling Fig 1 1 1B 1C 1 Assemble the handle 1 which is supplied with the unit to the gear case 2 Screw the chuck unit 2 into the drive shaft clockwise after the collar B 3 has been installed NOTE The collar B 3 is not used on Model TED 262 series 3 Insert the drill bit to be used after opening the chuck by the chuck handle 4 and tighten the chuck by the handle Selection of a Suitable Bit Choose a drill bit according to material to be drilled Operating procedures Fuel Fig 2 1 AS WARNING The power drill is equipped with a two stroke engine Always run the engine on fuel which is mixed with oil Provide good ventilation when fueling or handling fuel Fuel e Alw
9. ays use branded 89 octane unleaded gasoline e Use Tanaka two cycle oil or a quality two cycle oil at mixing ratio of 25 50 1 Gasoline A Oil B only for the state of California at 50 1 e Never use multi grade oil 10 W 30 or waste oil e Always mix fuel and oil in a separate clean container e Always start by filling half the amount of fuel which is to be used Then add the whole amount of oil Mix shake the fuel mixture e Add the remaining amount of fuel e Mix shake the fuel mix thoroughly before filling the fuel tank Fueling NWARNING e Always shut off the engine before refueling e Slowly open the fuel tank when filling up with fuel so that possible over pressure disappears e Tighten the fuel cap carefully after fueling e Always move the unit at least 3 m 10 ft from the fueling area before starting Before fueling clean the tank cap area carefully to ensure that no dirt falls into the tank Make sure that the fuel is well mixed by shaking the container before fueling www tanaka usa com 4 contacttanaka tanaka ism com Naka TED 210 TED 262L R DH HS Owner s Manual TED 262DH Fig 2 2 Fig 2 2B Starting 1 Set ignition switch 1 to RUN position Fig 2 2 2B Push priming bulb 4 several times so that fuel flows through the bulb or return pipe 5 If so equipped Fig 2 2C 2 Set choke lever to CHOKED position Fig 2 3 3B Pull the recoil starter handle briskly taking ca
10. gine speed to idle and move shift lever 2 to R Reverse position then accelerate to pull out e Shift lever may not move unless engine is running If so turn drill chuck a little bit by hand e The purpose of Lock control and Reverse control is mainly for easy removal of bit www tanaka usa com 6 contacttanaka tanaka ism com TED 210 TED 262L R DH HS Owner s Manual TED 262L 262DH TED 262R TED 262L 262DH Fig 2 6 Fig 2 6B TED 262R Fig 2 7B e To tighten the chuck more securely set a 19mm spanner 1 between gear case and drill chuck to lock drive shaft Turn on lock lever 2 first then hit the mounted chuck handle with a hammer to screw in clockwise the chuck TED 262L 262DH Fig 2 6 e To loosen the chuck set the spanner on the other side and hit the chuck handle from this side to screw out counterclockwise the chuck with the lock lever on TED 262L 262DH Fig 2 6B e Note In case of TED 262R use chuck mount wrench 3 in place of chuck handle and tighten or un tighten manually instead of hitting Do not hit the chuck mount wrench Fig 2 7 7B D 2 wi SU Es WR PT ei We S etn 1 e a MAE HO Oe CG eh RH E We Si e a e fi H Md D TED 262DH TED 210 e Fig 2 8 Fig 2 8B Fig 2 8C Stopping Fig 2 8 SB SC Gradually decrease the engine speed to an idle speed and then slide ignition switch 1 to STOP position www tanaka usa com 7 contacttanaka tan
11. harp and without cracks An off center bit induces heavy vibrations that may damage the unit Check that the drilling attachment is sufficiently tightened Check that nuts and screws are sufficiently tightened Weekly maintenance Check the starter especially cord and return spring Clean the exterior of the spark plug Remove it and check the electrode gap Adjust it to 0 6 mm 024 or change the spark plug Clean the cooling fins on the cylinder and check that the air intake at the starter is not clogged Check that the gear case is filled with grease up to 3 4 Clean the air filter Monthly maintenance Rinse the fuel tank with gasoline Clean the exterior of the carburetor and the space around it Clean the fan and the space around it www tanaka usa com 11 contacttanaka tanaka ism com la dh TED 210 TED 262L R DH HS Owner s Manual Specifications En MODEL TED 210 TED 262L R HS TED 262DH Bathntsttueraetsshecsutestesoteneresanasceeteeenna 22 1 34 Cu in 26 1 6 cu in Spark Plug EE NGK BPM 8A or BPMR 6A NGK BM 8A or BMR 6A 0 35 11 8 fl oz 0 5 16 89 fl oz TED 262L 4 5 9 9 Ibs 6 1 13 4 Ibs TED 262R 5 0 11 0 Ibs 3 9 B 6 bei TED 262HS 44 9 7 Ibs Chuck Capacity mm SAU ree Tete eter eee TET ee ey 12 7 1 2 in TE Drive Shaft Diameter eMe 1 2 20 UNF e Max Bit Size mm ee ee Ee ee ee ee ee 25 4 1 in Wood Bio Reverse Control rr TED 262R Q
12. his declaration relates is in conformity with the essential safety requirements of directives laquelle se rapporte la pr sente d claration est conforme aux directives concemant les conditions de s curit essentielles al quale questa dichiarazione si riferisce conforme ai requisiti di sicurezza essenziali delle direttive f r das these Erkl rung gilt den wesentlichen Sicherheitsanforderungen der Directive entspricht que corresponde a esta declaracl n satisface la s siguiente s exigencia s de seguridad esencial es de las directivas till vilken denna deklaration tillh r uppfyller samtliga v sentliga s kerhetskrav f reskrivna i ber rda direktiv 89 392 EEC 91 368 EEC 93 44 EEC 93 68 EEC EMC89 336 EEC The following standards have been taken into consideration ISO 3864 EN 292 2 Les normes suivantes ont t prises en consid ration Sono stati presi in considerazione i seguenti standard Die nachfolgenden Standards wurden in Betracht gezogen Se han tenido en consideraci n las siguientes normas Vi har tagit h nsyn till f ljande standards Manufactured at Chiba Japan Serial No up from 2001001 Fait No de s rie partir de Luogo Num di serie da Erstellt in Serien Nr ab Fabricado en No de Serie de en adelante Tillverkad av Serienr fr o m Signature Signature Firma Unterschrift Fimado Signatur Seiji Tanaka Position Vice president Function Vice pr6sident I
13. lanak Owner s Manual Model Numbers DIN 24929 TED 210 TED 262DH NM TED 262L R HS DRILLS TED 210 TED 262L Supplier To The Outdoor Power Equipment Industry ISM Inc 1028 4 Street SW e Auburn WA 98001 Phone 253 333 1200 Fax 253 333 1212 www tanaka usa com contacttanaka tanaka ism com TED 210 TED 262L R DH HS Owner s Manual Before using this unit Read the operator s manual carefully Check that the cutting equipment is correctly assembled and adjusted Start the unit and check the carburetor adjustment See Maintenance AA WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer birth defects and other reproductive harm Read understand and follow all warnings and Always wear eye head and ear protectors instructions in this manual and on the unit when using this unit It is important that you read fully understand and observe the following safety precautions and warnings Careless or improper use of the unit may cause serious or fatal injury Do not touch the bit when running the engine Explains choke position Upper sign indicates choke closed and the lower fully open Do not touch the bit when running the engine www tanaka usa com 1 contacttanaka tanaka ism com n 1 What is What Since this manual coves several models there may be some difference between pictures and your unit Use the
14. ncarico Vicepresidente Titel Stellvertretender Vorsitzender Cargo Vicepresidente Befattning Vice President www tanaka usa com 13 contacttanaka tanaka ism com
15. needed After that push the filter into intervals and more frequent under heavy use the tank completely Cleaning the cylinder fins Fig 3 6 When wood chips are caught between cylinder fins 1 the engine may overheat resulting in lower output To avoid this always keep cylinder fins and fan case clean Every 100 Operating hours or once a year more often if conditions require clean fins and external surfaces of engine of dust dirt and oil deposits which can contribute to improper cooling Cleaning the muffler Fig 3 7 Remove the muffler and spark arrestor if so equipped and clean out any excess carbon from the exhaust port or muffler inlet every 100 hours of operation For long term storage Drain all fuel from the fuel tank Start and let engine run until it stops Repair any damage which has resulted from use Clean the unit with a clean rag or the use of high pressure air hose Put a few drops of two cycle engine oil into the cylinder through the spark plug hole and spin the engine over several times to distribute oil Cover the unit and store it in a dry area www tanaka usa com 10 contacttanaka tanaka ism com TED 210 TED 262L R DH HS Owner s Manual Maintenance schedule Below you will find some general maintenance instructions For further information please contact your servicing dealer Daily maintenance Clean the exterior of the unit Check that the drilling attachment is properly centered s
16. re to keep the handle in your grasp and not allowing it to snap back Fig 2 4 TED 210 4 Once the engine is running move the choke to the Fig 2 3 run position Fig 2 3 3B NOTE At this stage if the engine does not start repeat procedure from 2 to 4 5 After starting the engine allow the engine about 2 3 minutes to warm up before subjecting it to any load Fig 2 3B Fig 2 4 www tanaka usa com 5 contacttanaka tanaka ism com TED 210 TED 262L R DH HS Owner s Manual Fig 2 5 Fig 2 5B Drilling Fig 2 5 5B e Always hold unit firmly with both hands on handles and body well balanced e Operate at a high engine speed and let the drill bit do the work Do not force bit into the hole e If materials become twisted around drill bit stop engine allow unit to cool and remove wire from spark plug before attempting to clear bit e Stop engine and inspect unit if abnormal vibration or noise is generated F TED 25LPF 262L TED 262DH TED 25RPF 262R Fig 2 5C Fig 2 5D How to operate Lock control on TED 262L 262DH Fig 2 5C NOTE Always stop the engine before operation of lock control e When bit has stuck in object stop engine and turn on lock lever 1 e Rotate whole unit counter clockwise so that the bit can be pulled out easily e If the unit would not move rotate it clockwise a little and then counter clockwise again How to operate Reverse control on TED 262R Fig 2 5D e Decrease en
Download Pdf Manuals
Related Search