Swann 1060 User's Manual
Contents
1. Help Desk Support Details All Countries E mail tech swann com au Telephone Helpdesk UNITED STATES toll free 877 274 3695 Sun Thurs 2pm 10 30pm PST 800 627 2799 Mon Fri 9am pm PST USA Exchange amp Returns 562 7 255 Mon Fri 9am 4pm PST AUSTRALIA toll free 1300 13 8324 Mon Fri 9am 5 30pm Aus EST International TOL 842 4010 Mon Fri Jam 5 30pm Aus EST See http Awww worldtimeserver com for information on different time zones and the time in Melbourne Australia compared to your local time WARRANTY INFORMATION Swann Communications warrants this product against defects in workmanship and material for a period of one 1 year from it s original purchase date You must present your receipt as proof of date of purchase for warranty validation Any unit which proves defective during the stated period will be repaired without charge for parts or labour or replaced at the sole discretion of Swann The repair or replacement will be warranted for either ninety days or the remainder of the original one year warranty period whichever is longer The end user is responsible for all freight charges incurred to send the product to Swann s repair centres The end user is responsible for all shipping costs incurred when shipping from and to any country other than the country of origin The warranty does not cover any incidental accidental or consequential damages arising from the use of or the inability to use this product Any co2. e same time Hot Weather Fan on at 98 6 F 37 C Cold Weather Heater on at 59 F 15 C If any of these items are missing please contact your retailer Connecting the Heater Blower Power Turn the camera on and adjust the focus to suit your requirement then close the top of the 1060 housing Using a Philios Head screwdriver re tighten the two screws at the side of the 1060 housing to ensure the best possible weather seal Connect the wires you passed through the seal plug to the Heater Blower power terminals with the positive and negative wires as marked in this illustration Once the wires are in the screw terminal holes tighten the screws down to give the wires a good electrical connection Opening the 1060 Housing Turn the 1060 Housing upside down and then using a Philips Head screwdriver loosen the two screws at the side of the 1060 housing until the top of the casing can be lifted towards the opposite side of the housing Turn the 1060 housing back to right side up and open the top sideways to allow access to the camera mounting plate fitted to the mounting rails at the bottom of the inside of the housing Gently prise the base plate up with your hand or use a screwdriver if this is too difficult Installing a Camera Connecting your Camera Fit your CCTV camera to the Insert the cables for camera mounting plate the Camera Power using the supplied mounti
3. g the 1060 Housing 7 and Swivel stand is available for Technical Specifications 7 separate purchase Product code Help Desk Support Details Back Cover SW A CBI Check with yo local Warranty Information Back Cover retailer for more details The Swann 1060 Camera Housing is designed to keep your CCTV camera safely enclosed to minimise the risk of damage by vandals or storms and also from being affected by inclement weather Its flexible design allows it to accommodate most CCTV cameras currently available The 1060 Housing also comes equipped with a low voltage heater bar and cooling fan to assist with keeping your images clear during periods of poor Technical Specifications weather Specification of Housing Dimensions L x W x H 15 x 514 x 4 400mm x140mm x1 12mm UB PES Ge GOTE Wo Weight 3 4lb 5Kg without camera e x CCTV Camera Housing Camera Opening Diameter 274 72mm e 2 x Cable Seal Plug with Rubber Grommet and Locking Nut Material Case Powder Coated Aluminium e x Camera Mounting Screw Camera Opening 7 3mm Glass e 2x Camera Base Plate Mounting Screws e x Imitation Camera Fascia Camera Mounting plate Impact Resistant Plastic e This Instruction Sheet Specification of Heater Blower Power Requirement 12 Volt DC 0 5amp 500mA Temperature Activation he fan or heater will activate automatically at the following temperatures The fan and heater do not both run at th
4. ng Camera Video and screw or the screws that may Heater Blower have come with your through the seal plug camera on the underside of the back end of the 1060 housing and pass the cables through in to the housing Once this is done tighten the nuts on the seal to prevent moisture and Cust entering Fit The Camera mounting plate back into The mounting rails Connect the Video and Power at the bottom of the housing and push down firmly until it wires you passed through the seal Clicks into place Make any necessary adjustments to the plug to your camera Connect distance from the glass or angle of the camera then screw the opposite end of the cables to in The supplied mounting screws to stop the mounting a video viewing device and plate from moving check for correct operation
5. sts associated with the fitting or removal of this product by a tradesman or other person or any other costs associated with its use are the responsibility of the end user This warranty applies to the original purchaser of the product only and is not transferrable to any third party Unauthorised end user or third party modifications to any component or evidence of misuse or abuse of the device will render all warranties void Swann wWwww swann com au Swann 1060 Camera Housing All Weather Camera Protection with inbuilt heater blower Swann Helpdesk Has the answers If this device does not work correctly when you first use it do not take it back to the store Contact the Swann Helpdesk using our fast e mail service tech swann com au or call us on one of the Toll Free numbers shown on the back cover of this booklet Most problems can be quickly and easily fixed with a simple e mail or a quick chat with one of our friendly technical staff Toll Free available in the US and Australia only Installation Guide INDEX Mounting the 1060 Housing Introduction 2 _ ae This package comes with 2 Using the built IN adjustable Opening the 1060 Housing 3 mounting points you can mount the Installing a Camera 4 1060 Housing on a stand pole or Connecting your Camera 5 wall bracket FOr alternative Connecting the Heater Blower Power mounting options the Universal mn Mountin
Download Pdf Manuals
Related Search