Sunrise Medical Guardian 93000 User's Manual
Contents
1. 45 The other end of the rail should easily be released from the post Figure 18 9 Place the rail in a box or bag to protect it from dust and or other damage 10 To remove the post slide the blue locking device up out of the bottom part of the Figure 29 post to unlock it 11 Loosen the post by twisting as follows Figure 29 a Turn top part of post to the left b Hold the bottom part of post firmly 12 Once the post is loose enough to allow you to move the post slide the top portion of the post down a Press the blue locking device back into the bottom part of the post b Raise the top portion of the post slightly Figure 12 c Press in metal pin on both sides of the post Figure 13 d Push top portion of post downwards e Repeat until the metal pins are no longer visible and the top of the post is only 6 8 152 200 mm above the blue locking handle 13 Remove the top plate from the post by pressing up evenly 3 Post System Specifications Maintenance II NOTE Metal pins cannot be pressed in when there is downward pressure on them Pressure must be released to press in pins 14 Remove the post from the foot plate by stepping on both sides with your feet and pulling the post up 15 Place all pieces into a box or bag to protect them from dust and or damage 16 Repeat steps 11 16 for the second and third posts NOTE Put the level and the Allen key with the rest of the Easytrack System for the next time you n2. Make sure the padding on the foot and top plate is clear of any foreign substance and is not damaged If neoprene rubber on either top or bottom plate appears damaged the plate must be replaced 4 Make sure the level is still working 5 Look for signs of wear or breakage on all parts Replace any parts that appear worn or damaged AWARNING Follow guidelines in your portable lift manual for maintenance and procedures on the lift 3 Post System Troubleshooting 13 TROUBLESHOOTING PROBLEM CORRECTION Trolley moves substantially on its own when the Easytrack System is fully assembled Are posts straight Use level see assembly instructions step 11 Are the rails secured to the posts Press up on the rail to make sure that the rail is latched onto the post Is the ceiling level An uneven ceiling will make the rail uneven See Requirements section in manual Extended rail comes completely apart during assembly Rail has been extended too quickly forcefully Rail was pulled past the locking device Check locking device inside rail top of rail above the trolley to make sure it is not damaged Replace trolley if damaged See Easytrack Kit Contents amp Part Numbers section of manual 3 Put rail back together at a slight angle and slide together Slowly extend rail out again to make sure locking device clicks into place 5 Slowly compress rail again Not able to push pin to as
3. a joist or truss is not required but preferable 24 max Joists Joists Suspended wire or roas 41 2 min T hi et FS hse rock ba Sheet rock or tile Floor Requirements e Ensure flooring meets local building code standards Termites or water damage may affect the structure of the floor e Ensure floor is clear of any dust grease water or any foreign substance e Floor must not have a slope of more than 0 5 See drawing below to determine the floor slope Use a level or contact a contractor if unsure of floor slope P1 i X 12 300mm 24 600mm 36 900mm 48 1200mm Y 0 10 2 6mm 0 21 5 2mm 0 31 7 9mm 0 42 10 5mm AWARNING e Ensure posts are straight using the level provided failure to do so may cause injury e Every month a maintenance check should be done to ensure all posts are level See Maintenance section in this manual e Make sure the padded surface of the top plate and foot plate are kept clean and are intact e Protect the Easytrack System and its accessories during transport 3 Post System Before You Begin 5 BEFORE YOU BEGIN AWARNING Read Requirements and Important Safeguards before attempting to assemble the Easytrack System 1 Survey the room where you plan to install the Easytrack System Make sure the room meets all the specifi cations outlined in Requirements 2 Use the measurements below to determine the best place to
4. Guardian Easytrack System Installation 3 Post Assembly er Model 93000 Instruction Manual DICAL 2 Introduction TABLE OF CONTENTS INtrOd UCI Dec dm Gisela dal 2 Important Satequardsecssecon ssciimastsmiicttcesmssst mmerssit nies ts treia 3 R quiremehtS asoni a a a fs devel a E 4 Before YOU BeGin iseccnesceaxssezessedcdesscccagseaeduasadcecavascesdesses e L ei 5 Kit Contents 8 Part Numbers ssirmecsreriieree deiri a E EEA 6 Assembly of 3 Post System ssessssssssssessseeessssosssssssseesssseesssessseeesssesseeesse 6 Disassembly of 3 POSt Sytem cccessecccsssccceesseecceeeeceeeseceeessceeeaseeeeeeeees 9 3 P st SpecificationS cecs tit alta ttes it tiet ies citi e olla 10 Maintenance versi iaia ee E EA AE EAA ER 11 Tro blesh otingi nseni ennaa a aaa EERE EE a LETE OE 13 Easytrack Products amp Accessories ssssssssesssssesssseessseeesssesssessssesesssesssseesse 14 Warranty iii tieta micos i a aas a 15 AWARNING This manual contains important safety and maintenance instructions Please read it carefully before using your Easytrack System and refer to it as often as needed for safe and efficient use If you have questions regarding the safe use and or assembly maintenance or specifications of your Easytrack System you should call Customer Service at 800 333 4000 303 218 4600 or from Canada at 800 263 3390 For service and repair remember your authorized Sunrise supplier is able to provide the assist
5. ance you need Save this manual for future reference SUNRISE LISTENS Thank you for choosing a Guardian Easytrack System We want to hear your questions or comments about this manual the safety and reliability of your Easytrack System and the service you receive from your Sunrise Medical Supplier Please feel free to write or call us at the address and telephone number below Sunrise Medical Customer Service Department 7477 East Dry Creek Parkway Longmont Colorado 80503 303 218 4600 or 800 333 4000 FOR ANSWERS TO YOUR QUESTIONS Your authorized supplier knows your Easytrack System best and can answer most of your questions about its safety use and maintenance For future reference fill in the following Supplier Address Telephone Serial Date Purchased 3 Post System Important Safeguards 3 IMPORTANT SAFEGUARDS AWARNING Do not operate this equipment without first reading and understanding this manual AWARNING Should you be unable to understand the warnings cautions and instructions contact our technical support or your local dealer before attempting to use this equipment otherwise injury or damage may result Important information is highlighted by these terms A WARNING Notices as used in the manual apply to hazards or unsafe practices which could result in serious bodily harm CAUTION Notices as used in this manual apply to hazards or unsafe practices which could result
6. e post quickly towards the ceiling by pulling the top portion and holding the bottom portion Click The post should be within 3 76 mm of touching the ceiling If the top of the post is more than 3 76 mm from the ceiling a Raise the top portion of the post slightly Figure 12 b Press in metal pin on both sides of the post Figure 13 CAUTION Metal pins cannot be pressed in when there is downward pressure on them Pressure must be released to press in pin Figure 10 Figure 11 Figure 12 c Pull top portion of post up towards the ceiling d Repeat until the top of the post is less than 3 76 mm from the ceiling Figure 13 Figure 14 10 Lift the blue locking handle out of the lower portion of the post Using the blue piece as a handle twist the post as follows Figure 14 a Turn the top portion counter clockwise b Hold the bottom portion firmly 11 Before the Easytrack post tightens against the ceiling check the clip on level to make sure the bubble is in the center of the circle Tilt the post until the bubble reaches the center of the circle Figure 15 AWARNING Make sure clip on level is fully attached to the post Failure to attach level properly could give an incorrect reading Level should click into place Figure 15 3 Post System 8 Assembly of 3 Post System 12 Once the bubble is in the center of the clip on level continue to tight en ONLY un
7. eason of repairs made to any component without the specific consent of Sunrise Medical or to products damaged by circumstances beyond Sunrise Medical s control Evaluation of warranty claim will be solely determined by Sunrise Medical The warranty does not apply to problems arising from normal wear or failure to adhere to the instructions in this manual Sunrise Medical Inc slings are void of warranty if not laundered as per instructions on the Sling Label Sunrise Medical Inc shall not be liable for damages losses or inconveniences caused by a carrier This warranty replaces any other warranty expressed or implicit and constitutes Sunrise Medical Inc s only obligation towards the purchaser Sunrise Medical shall not be liable for any consequential or incidental damages whatsoever 15 3 Post System SUNRISE MEDICAL www sunrisemedicalonline com Distributed by Sunrise Medical 7477 East Dry Creek Parkway Longmont Colorado 80503 800 333 4000 In Canada 800 263 3390 Printed in Canada 2001 Sunrise Medical 10 01 900 0610 Rev A
8. ed Step 2 onto the second post The rail should click in place Press up on the rail to make sure it is locked into place NOTE Do not squeeze sides of rail together when attempting to extend or contract the rail Squeezing the rail makes it more difficult to slide 19 Take the Pivoting Extendable Rail with standard trolley out of the box a Take the flat blue cap off of the end of the rail Figure 19 3 Post System Assembly of 3 Post System 9 b Find the end stopper from inside the top of the rail The top por tion is the section without the small trolley in it Figure 20 c Using the Allen key provided loosen the stopper in the upper portion of the rail and slide it out of the rail Figure 21 20 Place the end of the rail with the hooks onto the pivot post Figure 22 NOTE Tilt the rail upward 45 to latch the rail onto the post 21 Extend the rail and thread the wheels of the trolley through the upper portion of the rail Figure 23 22 Continue to extend the rail through the metal U shaped attachment Rail should extend a minimum of 21 3 55 1 540 1400mm beyond the U shaped attachment 23 Add the stopper to the top portion of the rail a Place the stopper in the upper I portion of the rail vvith the rub Figure 22 Figure 23 ber bumper leading Figure 24 Slide stopper so it is approximately 1 25 mm from the end of the rail b Using the Allen key tighten the
9. eed to assemble it SPECIFICATIONS Item NUMDEL sssseereeccreeeseees 93000 Weight Capacity 440 lbs 200 kg Length of Rail eens 74 124 5 1900 3160mm Length of Posts sses 84 108 2130 2745mm Material Anodized Aluminum A Weight ssssssesesseees 93 5 lbs 42 5kg gi Ceiling Plate siesta 20 510 mm s Floor Plates 4 8 120 mm MAINTENANCE AWARNING Maintenance must be performed only by qualified personnel AWARNING Failure to follow maintenance instructions below when indicated could result in injury or damage AWARNING Periodic inspection should be performed by a person who is suitably and properly qualified and well acquainted with the design use and care of the Easytrack System Inspection should be carried out both routinely at least as often as specified and as necessary All defects and damage that have lead to corrective actions should be noted signed and dated by the inspector Defects and resulting actions should be reported in writing to your supplier 3 Post System 12 Maintenance Upon receipt of your Easytrack System 1 Make sure you received all components listed in Figure 6 Inspect all parts for possible damage in transit Ensure all components are in working order Arrange for repair replacement of any faulty parts Keep a log of any repair replacement required om amp WwW N Before each use of the Easytrack Syste
10. f flooring is not according to local building code standards flooring may be damaged e Do not install on a sloped floor e Do not drop product may cause breakage e Do not completely submerge in water Do not attempt to over extend the rail past the locking point e Do not install product if neoprene on top or bottom plate appears to be damaged or absent When the Easytrack is in Use AWARNING e Do not hit posts this might cause unit to become unstable If posts are hit reassemble Easytrack System to ensure the posts are straight e If you use a power wheel chair use extreme care Hitting posts may cause unit to become unstable If posts are hit reinstall the Easytrack System to ensure the posts are straight e Do not lean against posts e Do not use the Easytrack System as a swing e Refrain from swinging user sideways of rail 3 Post System 4 Requirements REQUIREMENTS AWARNING Failure to meet requirements listed below could result in serious bodily harm Ceiling Requirements e Install to a rigid ceiling must have a framework above it e Must have a maximum of 24 610mm between the trusses in the ceiling e Ceiling must be made of wood or 1 2 12 7mm sheet rock or thicker e Ensure ceiling and floor are clear of any dust grease water or any foreign substance AWARNING A build up of nicotine grease or water on the ceiling will affect the integrity of the Easytrack System Installing a post directly under
11. for rail stopper not shown 900 4580 ASSEMBLY OF 3 POST SYSTEM Tools Required e Step ladder e Tape measure e An assistant 1 Decide where you will place your pivot post and the other two stan dard posts There must be a minimum of 75 1 90 m of space between each of the standard posts and a Figure 7 Figure 8 minimum of 21 3 55 1 540 1400mm between the standard posts and the nearest wall Figure 3 NOTE Posts are not the same see Figure 6 for more details 2 Remove the round blue plastic caps from the top of each post by pulling them away from the post Figure 7 3 Remove the blue plastic strips from each side of the posts Take one end and pull gently Figure 8 4 Place one round foot plate on the floor where you want to place the pivot post of the Easytrack System 3 Post System Assembly of 3 Post System 7 5 Take the pivot post out of the box and the post top for pivot post Insert the post top into the post until it snaps into place Figure 9 6 Take top plate and clip on level out of the box Place the clip on level onto the post at approximately waist height Figure 10 7 Place the post onto the foot plate and press down to tighten Pay attention to the shape of the post and foot plate before pressing down onto the foot plate 8 Place the top plate into the top of the post pressing firmly and evenly downward until the top plate clicks into place Figure 11 9 Extend th
12. hey dry completely before reassembling post 3 Replace foot plate s or top plate s if neoprene is damaged Is ceiling clean Clean ceiling and or floor See Requirements section of manual Trolley does not roll in rail smoothly Is rail clean Clean rail with damp cloth Is trolley centered in rail Re center trolley Is the trolley damaged Replace trolley See Easytrack Kit Contents amp Part Numbers Pivoting rail does not slide all the way over to one or both sides Is the pivoting rail extended far enough beyond the other rail Lengthen pivoting rail by pulling fur ther Is the pivoting post too far from the two standard post If the pivoting rail can t reach the swivel trolley rail you need to decrease this distance Follow Disassembly instructions and reassemble the 3 post Easytrack See Figure 3 for information on dimensions and layout Does the pivoting rail need to be more centered between the two standard posts Figure 30 Pivoting post may need to be moved so it is more centered between the two standard posts Follow Disassembly instructions and reassemble 3 post Easytrack 8 Pivoting rail seems to be at an angle and rail slides freely towards one direction Is the ceiling level See Requirements section of this manual for more information Is the pivoting rail properly attached to the pivoting post See Figure 3make sure that the proper post was used The piv
13. in minor personal injury or property damage NOTES Highlight procedures and contain information which assist the operator in understanding the information contained in this manual NOTE The information contained in this document is subject to change without notice SAVE THESE INSTRUCTIONS AND KEEP WITH EASYTRACK AT ALL TIMES AWARNING The Easytrack System and its accessories are intended to be used as an assistive device for transferring a person between the posts The Easytrack system is only to be used with the Guardian Voyager Portable lift AWARNING USE ONLY AS INTENDED This product may cause serious injury if not installed and operated according to the instruction manu al Failure to observe warnings listed below could result in serious injury Before You Install the Easytrack AWARNING e Carefully inspect product upon arrival If any pieces are missing or appear damaged do not install Contact your local supplier for further instructions e If you are unsure of the strength or stability of your floor and or ceiling do not install the Easytrack System consult you local supplier e Easytrack can not be used with any type of suspended ceiling including suspended drywall acoustic tile etc e Installation on a plaster ceiling may cause cracking Sunrise Medical cannot be held responsible for damage e Do not install on a ceiling with water damage e Do not over tighten ceiling plate as this may cause ceiling to crack e I
14. m 1 Make sure posts are straight If they do not appear straight use level to check If posts are not straight remove rail see Disassembly and re install posts see Assembly 2 Ensure that the red zone on top of the post under the top plate is not visible 3 Check that the rail is secured in place Press up on the rail to make sure that the rail is locked onto the post 4 Check for any appearance of damage If there is apparent damage do not use the Easytrack System Every month 1 Use level supplied to ensure all posts are straight 2 Clean inside of rail with a damp cloth to ensure there is no dust or grease build up inside of rail 3 Make sure the red zone is not visible If red zone is visible tighten posts according to assembly instructions 4 Check to ensure you still have all your original parts If any parts are missing they should be replaced before using the Easytrack again 5 Check to make sure that the trolley in the rail moves freely Trolley may need to be cleaned or replaced 6 Check for the appearance of rust If rust is starting to appear simply scrub the piece clean 7 Examine all joints and pieces for wear and fatigue Replace any part that looks dam aged or worn 8 Document inspection and any repairs If equipment is moved on a regular basis 1 Make sure all components are accounted for 2 Check Requirements and Important Safeguards before reinstalling the Easytrack System 3
15. oting post and standard post are not the same Is the extendable rail with swivel trolley secured on the post Push up on the rail to ensure it is locked 3 Post System 14 Easytrack Products amp Accessories EASYTRACK PRODUCTS amp ACCESSORIES Easytrack 2 Post SYStGM i s ncis ccaceccesesasentesecssessesdccoesedsecepacenennasewet st vepeeesarys 92000 Easytrack 4 Post SYSteM cciecsaseconnntesnsssvsovescesvesscooetececesopsannensivansatssessosedese 94000 Easytrack 2 Post with Tub Bracket ccceseseeseecceeeeeeeeeeeeeeeeeesssseseeseeeeees 92001 Easytrack 3 Post with Tub Bracket ccceseeeeeseccceeeeeeeeeeeeeeeeessssseeseseeees 93001 Easytrack Portable Carry Bag cccccsssssecccccetseececcceeeseececeseeesececeeeeeeeeeees 92341 3 Post System Warranty WARRANTY This warranty is extended only to the original purchaser user of Sunrise products Sunrise Medical Inc warrants its products to be free from defects in material under normal use and service and will within the periods stated below from the date of purchase If within such warranty period any such product shall be proven to be defective such product shall be repaired or replaced at Sunrise Medical s option This warranty does not include any labor or shipping charges incurred in replacement part installation or repair of any such product Sunrise Medical s sole obligation and your exclusive remedy under this warranty shall be limited to such re
16. pair and or replacement Lifter including Hydraulics 1 year Accessories on Lifter 1 year Slings 1 year Batteries 3 months Easytrack System 1 year For warranty service please contact the provider from whom you purchased the Sunrise Medical product In the event that you do not receive satisfactory warranty service please contact Sunrise Medical customer service at 1 800 333 4000 Do not return products to our factory without prior authorization Sunrise Medical will issue a Return Merchandise Authorization RMA Number C 0 D shipments will be refused all shipments to Sunrise Medical must be prepaid For this warranty to be valid the purchaser must present its original proof of purchase at the moment of the claim The defective unit assembly or part must be returned to Sunrise Medical for inspection The part or compo nents repaired or replaced are guaranteed for the remaining period of the initial warranty Limitations and Exclusions The above warranty does not apply to serial numbered products if the serial number has been removed or defaced No warranty claim shall apply where the product or any other part thereof has been altered varied modified or damaged either accidentally or through improper or negligent use and storage Warranty does not apply to products modified without Sunrise Medical s express written consent including but not limited to products modified with unauthorized parts or attachments products damaged by r
17. put the Easytrack System a Over a bed approx 36 40 915 1020 mm from the head of the bed Figure 1 b Over a tub approx 16 18 400 460 mm from the end of the tub Figure 1 c Allow 36 1000 mm of open area for transfer working space Figure 2 d Transfers should only take place between the Easytrack System posts Figure 3 3 Though it is not a requirement to place the posts directly under a joist in the ceiling it is preferable It does not matter which direction the top plate is facing Figures 4 amp 5 E o nN N I o mM N 84 108 PREFERABLE OX Joists gt Joists aa J Sheet STEN Fastac L rock Sheet rock post Easytrack OK ost Easytrache DE oF post Figure 4 Figure 5 3 Post System 6 Assembly of 3 Post System EASYTRACK 3 POST SYSTEM KIT CONTENTS amp PART NUMBERS Figure 6 Description Part Qty 1 Pivoting extendable rail w standard trolley 900 0850 1 2 Extendable rail w swivel trolley 900 0800 1 3 Pivot post 22 1 4 Post top for pivot post N A 4 5 Standard post 900 0500 2 6 Blue locking handle N A 3 7 Round blue cap 900 0720 3 8 Allen key 900 3280 1 9 Clip on level 900 0600 1 10 Top plate 900 0400 3 11 Round foot plate 900 0350 3 12 Blue plastic strips 2 post 900 0230 6 13 Flat blue cap 900 1050 1 14 C H protector 900 0780 1 15 Swivel trolley 900 0900 1 16 Standard trolley 900 0650 1 Figure 6 Set screw
18. semble disassem ble post Not able to tighten post enough to hide red zone Is the post still tight against the ceiling Release pressure on posts by unscrewing blue locking device See Disassembly instructions step 11 Are you lifting the upper portion of the post slightly to release pressure Raise upper portion of post first and push the pin in See Assembly instructions step 9 or Disassembly instructions step 12 Have you extended the post enough Unscrew using the blue locking handle see Disassembly instruction step 10 slide post up one or more notches then screw the upper portion of the post to tighten See Assembly instructions step 10 If the post has been unscrewed to the maximum and will not turn anymore reverse direction to shorten the post several inches then slide the post up another notch See Assembly instructions steps 9 10 Are you holding the bottom portion of the post firm while twisting the upper portion of the post towards the right See Assembly instructions step 10 Is the blue locking handle up out of the lower portion of the post when turning the upper portion to the right See Assembly instructions step 10 Posts do not appear stable Is red zone still visible See Assembly instructions step 12 and Troubleshooting problem 4 Is neoprene rubber on either top plate or foot plate damaged or dirty Clean both foot plate and ceiling plate with soap and warm water Make sure t
19. stopper in place c Slowly move the rail from post to post to make sure it moves freely If it does not move freely the rail needs to extend further out CAUTION Make sure the stopper is snug DO NOT OVER TIGHTEN d Snap the flat blue cap onto the Figure 24 Figure 25 end of the rail Figure 19 24 Place one round blue end cap on the top of each post Figure 25 NOTE Put the level and the Allen Key in a safe place as you may need them in the future 25 Slide the blue plastic strips into the sides of the posts by pinching the strip on each side to press it into the grooves Start at the bottom of the post Figure 26 26 See Figure 27 for photo of assembled 3 Post Easytrack System Figure 26 3 Post System 10 Disassembly of 3 Post System AWARNING BEFORE USING THE EASYTRACK SYSTEM GO THROUGH THE FOLLOWING CHECKLIST Make sure the red zone on top of all posts are not visible Make sure the posts are straight Did you use the clip on level Make sure the rail is locked into place see step 15 and that it looks level Make sure the stopper is snug see step 22b Make sure the pivoting rail slides smoothly from side to side Check your installation against Figure 27 Is the blue locking handle secured down into the lower portion of both posts SSRSSSRSS DISASSEMBLY OF 3 POST SYSTEM AWARNING Ensure no one is in the lift and remove the lift from the Easytrack before adjust ing or disassembling the Easytrack S
20. til the red zone at the top of the post is no longer visible Figures 16 A amp B AWARNING Red zone must not be visible for the post to be safely secured AWARNING o not over tighten the post Figure 16 A Figure 16 B Tighten only until red zone disap pears Over tightening post may cause damage to the ceiling 13 Remove the level from the post by sliding it up off the bottom portion of the post Slide the blue locking handle down to fit into the bottom part of the post to lock the post in place Figure 17 14 Repeat steps 4 12 for second and third posts NOTE Once the blue locking handle is pressed a cag except top and foot plates This will not lower post The post must turn to enable you to attach the rail Figure 18 NOTE Make sure the three posts are far enough away from each other to allow the rail to attach 75 1 90 m 15 Get the Extendable Rail with swivel trolley 16 Place the end of the rail marked Step 1 onto one standard post not the post designated to be the pivot post Figure 18 If pins on top of post are not facing in direc tion desired place rail onto pins and Figure 19 rotate post to desired direction 17 Raise the rail slightly and extend the rail to the second standard post not the post designated to be the pivot post Figure 19 NOTE Tilt the rail upward 45 to latch the rail onto the post Figure 18 18 Latch the end of the rail mark
21. ystem Tools Required Figure 27 e Step ladder e An assistant 1 Remove plastic strips from the sides of the posts To remove take one end of the strip and pull outward gently Figure 8 2 Remove the round blue caps from the ends of the rails by pulling them away from the post Figure 7 3 Using a step ladder a Remove the flat blue end cap from the end of the pivoting rail Figure 19 b Take the Allen key and loosen the stopper inside the upper portion of the pivot ing rail Remove the stopper from inside the rail Figure 24 4 Slowly contract the rail so the 4 wheeled trolley is exposed Once the rail is free of the trolley lower the rail slightly and contract the rail all the way in Figure 23 5 Tilt the rail 45 and lift the other end off of the pivoting post Figure 22 NOTE Do not squeeze sides of rail together when attempting to extend or contract the rail Squeezing the rail makes it more difficult to slide Figure 28 6 Place the stopper back into the upper portion of the pivoting rail and tighten with the Allen key Figure 21 Put the flat blue end cap back onto the rail NOTE Place the rail in a box or bag to protect it from dust and or other damage 7 Using a step ladder reach under the section of the remaining rail labeled Step 2 and pull the blue tab away from the post slightly to release the lock on the rail Figure 28 8 Push end of rail to contract the rail and tilt the rail downward
Download Pdf Manuals
Related Search