Sunpentown Intl WA-1205E User's Manual
Contents
1. 0388 or visit www sunpentown com This GRARANTEE is in addition to your Statutory Rights Dear Customer Please keep this warranty for your record DO NOT return it2. the batteries Otherwise battery leakage may damage the remote controller 3 The average battery life under normal use is about 6 months 4 Replace the batteries when there is no answering beep from the indoor unit or if the Transmission Indicator light fails to appear Q AUTOMATIC OPERATION When the Air Conditioner is ready for use switch on the power and the OPERATION indicator lamp on the display panel of the indoor unit starts flashing 1 Use the MODE select button to select AUTO 2 Push the TEMP button to set the desired room temperature The most comfortable temperature settings are between 21 C 70 F to 28 C 82 F 3 Push the ON OFF button to start the air conditioner The OPERATION lamp on the display panel of the indoor unit lights The operating mode of AUTO FAN SPEED is automatically set and there are no indicators shown on the display panel of the remote controller 4 Push the ON OFF button again to stop the unit operation NOTE 1 In the AUTO mode the air conditioner can logically choose the mode of COOL FAN HEAT and DRY by sensing the difference between the actual ambient room temperature and the set temperature on the remote controller 2 If the AUTO mode is not comfortable for you the desired mode can be selected manually Q COOL HEAT and FAN Operation 1 If the AUTO mode is not comfortable you may manually override the settings by using COOL DRY HEAT HEAT PUMP units only or FAN ONLY m
3. to window 5 FAN OPERATION Press the MODE button several times until the FAN indicator light comes on Press the FAN SPEED button to choose the fan speed Do not put the duct to window 6 TIMER OPERATION Setting the on timer Press the TIMER ON button when the air conditioner is off Select the time you need the unit start to operate The Operation Paned Window will display ON The starting time is adjustable from 0 00 to 24 Setting the off timer Press the TIMER OFF button when the air conditioner is on Select the time you need the unit turn off The Operation Panel Window will display OFF The turning off time is adjustable from 0 00 to 24 WATER PUMP DRAINAGE Connect the water pump drain hose to the unit before operate When the water level of the internal water tank reaches a predetermined level the water pump will be activated and drain the condensed water outside through the connected drain hose The maximum delivery lift is 3 5m Under this condition attach the rubber blockage to the back hole to prevent continuous drainage 8 CONTINUOUS DRAINAGE When you plan to leave this unit unused for a long time remove the rubber blockage form the back hole and attach a section of the continuous drain hose to drain hose connector All the water in the water tank would drain outside through the drain hose Under this condition the water pump is not activated N INSTALLATION 1 IMPORTANT Instal
4. AMAGED IT MUST BE REPLACED BY A REPAIR SHOP APPOINTED BY THE MANUFACTURER BECAUSE SPECIAL PURPOSE TOOLS ARE REQUIRED NOTE The air conditioner can be connected only to a supply with system impedance no more than 0 4582 ohm In case necessary please consult your supply authority for system impedance information NAMES OF PARTS OPRATION PANEL AIR INLET INDOOR pum REAR COVER FRONT COVER AIR OUTLET AIR OUTLET OUTDOOR WATER PUMP DRAIN HOSE AIR INLET OUTDOOR AIR INLET REMOTE CONTROLLER OUTDOOR CONTINUOUS DRAIN HOSE i MI a QU CASTER FRONT VIEW SIDE VIEW REAR VIEW Fig 1 ACCESSORIES PARTS NAME QUANTITY ADAPTOR A FOR PERMANENT DUCT MOUNTING ADAPTOR FOR TEMPORARY DUCT MOUNTING SCREWS ALKALINE BATTERIES REMOTE CONTROLLER WATER PUMP DRAIN HOSE Fig 2 wn Check all the accessories are included in the package and please refer to the installation instructions for their usage OPERATION PANEL OF THE All AND HEATING COOL DRY FAN HEAT INDICATIOR DIGITAL DISPLAY FAN SPEED INDICATOR Green lamp will light when the mode is selected WATER FULLINDICATOR Red lamp will blink when the tank is full TEMP SETTING BUTTON Press your desired room temperature setting by pressing the button A up or button S7 down INFRARED SIGNAL RECEIVER POWER INDIC
5. ATOR POWER BUTTON Turn on off the unit TIMER ON OFF INDICATOR MODES BUTTON Select the operation mode from COOL DRY FAN HEAT FAN SPEED BUTTON TIMER ON OFF BUTTON Select the fan speed from Program the on off timer function HIGH MED or LOW OPERATING PANEL Fig 3 OPERATION PANEL OF THE Alle CONDITIONER COOLING ONLY TYPE COOL DRY FAN INDICATOR DIGITAL DISPLAY FAN SPEED INDICATOR Green lamp will light when the mode is selected WATER FULLINDICATOR Red lamp will blink when the tank is full TEMP SETTING BUTTON Select your desired room temperature setting by pressing the button A up or button S7 down POWER INDICATOR INFRARED SIGNAL RECEIVER POWER BUTTON Turn on off the unit TIMER ON OFF INDICATOR MODES BUTTON Select the operation mode from COOL DRY FAN FAN SPEED BUTTON TIMER ON OFFBUTTON Press the button to select the fan speed from t loff ti i rogram the on off timer function HIGH MED or LOW OPERATING PANEL Fig 4 OPERATING INSTRUCTING FOR THE AIR CONDITIONER Before Starting This Unit 1 Select a suitable location make sure you have easy access to an electrical outlet 2 Install the Flexible Exhaust Hose and the Adjustable Window Slider Kit as depicted in Fig 5 amp Fig 5a 1 BEFORE USE Dehumidifying and Cooling Operations The operating range for cooling operating is 17 C 30 C 63 F 86 F Ifthe cooling or dehumidifying operations have been switched off and
6. DO NOT OVER BEND THE DUCT SEE Fig 10 Window Kit Installation Your window kit has been designed to fit most standard Vertical and horizontal window applications However it may be necessary for you to improvise modify some aspects of the installation procedures for certain types of window Please refer to Fig 11 amp Fig 11a for minimum and maximum window openings Drain Tank Safety Feature This unit is equipped with a internal water tank two full safe switch mechanisms one is used to control the water pump drainage the other is used to monitor the water level inside the internal water tank When the water level reaches a predetermined level the full safe switch mechanism is activated The digital display shows P1 and the water full indicator light illuminates Carefully move the unit outside remove the rubber blockage from the back drainage hole and drain the water off The unit will continue operating properly MAINTENANCE IMPORTANT 1 BE SURE TO UNPLUG THE UNIT BEFORE CLEANING Horizontal window Window Slider Kit Minimum 67 5cm 2 22ft Maxmum 123cm 4 04ft Fig 11 Horizontal window Window Slider Kit Minimum 67 5cm 2 22ft Maxmum 123cm 4 04tt Fig 11a 2 DO NOT USE GASOLINE THINNER OR OTHER CHEMICALS TO CLEAN THE UNIT 3 DO NOT WASH THE UNIT DIRECTLY UNDER A TAP OR USING A HOSE THE ELECTRICAL CAUSE DANGER 4 IF THE POWER CORD IS DAMAGED IT SHOULD BE REPAIRED B
7. P ONLY LOCK display is displayed by pushing the LOCK button Push the LOCK button again to clear display 3 TIMER Display This display area shows the settings of TIMER That is if only the starting time of operation is set it will display the TIMER ON If only the turning off time of operation is set it will display the TIMER OFF If both operations are set it willshow TIMER ON OFF which indicates you Fig 2 have chosen to set both the starting time and off time FAN Display When the FAN button is pushed this signal indicator lights Digital Display Area This area will show the temperature and ifin the TIMER mode will show the ON and OFF settings of the TIMER A NOTE All items are shown in the Fig 2 for the purpose of clear presentation But during the actual operation only the relative functional items are shown on the display panel Operating of the Remote Controller Install Replace Batteries The Remote Controller uses two alkaline dry batteries RO3 Ir03X2 1 To install batteries slide back the cover of the battery compartment and install the batteries according to the directions and shown on the Remote Controller 2 To replace the old batteries use the same method as mentioned above A NOTE 1 When replacing batteries do not use old batteries or a different type battery This may cause the remote controller to malfunction 2 If you do not use the remote controller for several weeks remove
8. Y MANUFACTURE OR ITS AGENCY 1 AIR FILTER Clean the air filter at least once every two weeks to prevent interior fan operation because of dust Removal Pull out the filter cover and remove the air filter from the filter cover Cleaning Wash the air filter by immersing it gently in warm water about 40 C 104 F with a neutral detergent Rinse the filter and dry it in a shady place Mounting Attach the air filter to the filter cover using the attachment hooks on the inner surface of the cover Put the filter cover back to the unit 2 UNIT ENCLOSURE Use a lint free cloth soaked with neutral detergent to clean the unit enclosure Finished by a dry clean cloth TROUBLE SHOOTING TROUBLES POSSIBLE CAUSES SUGGEST REMEDIES 1 UNIT DOES NOT START WHEN PRESSING 1 0 BUTTON 2 NOT COOL ENOUGH 3 POWER SHUT OFF AT HEATING MODE 4 NOISY OR VIBRATION 5 GURGLING SOUND Water full indicator blinks water tank is full Room temperature is higher than the set temperature Heating mode Room temperature is lower than the set temperature Cooling mode The windows or doors in the room are not closed There are heat sources inside the room Exhaust air duct is not connected or blocked Temperature setting is too high Air filter is blocked by dust The automatic over heat protection function When the temperature at the air outlet exceed 70 C 158 F the device will stop T
9. e SUNPENTOWN PORTABLE AIR CONDITIONER OWNER S MANUAL Models WA 1205E Thank you for purchasing this product Please read this Owner s Manual carefully before operating Table of Contents CONTENTS RULES re en orco con 1 Z NAMES PARTS SM EFIE 2 SACGGESSORIES 2 4 0PERATION PANEL OF THE AIR CONDITIONER 3 5 0PERATING INSTRUCTION FOR THE AIR CONDITIONER 4 INSTALLATION zn 6 DEMAIN TENE E srein arre nacen ke nara 7 SG TROUBLE SHOOTING E dE EXP E ERR MR AK YEN 8 REMOTE CONTROLLER rin 9 13 TO GUARANTEE sssi nannte 14 SAFETY RULES 1 DO NOT CONNECT UNIT TO ANY AC SOCKET IN DISREPAIR OR WITH CONNECTIONS 2 DO NOT USE IN THE FOLLOWING LOCATIONS NEXT TO SOURCE OF FIRE AN AREA WHERE OIL IS LIKELY TO SPLASH ANAREA EXPOSED TO DIRECT SUNLIGHT ANAREA WHERE WATER IS LIKELY TO SPLASH NEAR A BATH A SHOWER OR A SWIMMING POOL IN THE GREEN HOUSE 3 NEVER INSERT YOUR FINGERS OR ANY FOREIGN OBJECTS INTO THE AIR OUTLET TAKE SPECIAL CARE TO WARN CHILDREN OF THESE DANGERS 4 ALWAYS STORE THE UNIT UPRIGHT IN ORDER TO MAINTAIN THE COMPRE SSOR IN A PROPER CONDITION 5 BE SURE TO UNPLUG THE UNIT BEFORE CLEANING 6 THE HEATER MUST NOT BE LOCATED IMMEDIATELY BELOW A SOCKET OUTLET 7 IF THE APPLIANCE IS COVERED THERE IS A RISK OF OVERHEAT 8 IF THE SUPPLY TOOL OF THIS APPLIANCE IS D
10. e controller transmits the signal to the air conditioner Then after approximately another 2 seconds the signal h disappears and the set temperature will re appear on the digital display 2 To set the stopping time 2 1 Push the TIMER OFF button and the remote controller will show TIMER OFF the last set time for the stopping operation and the signal h will be shown on the DIGITAL DISPLAY area You are now ready to reset the time of the STOP operation 2 2 Push the TIMER OFF button again to set the time you want to stop the operation 2 3 After setting the TIMER OFF there will be a one half second delay before the remote controller transmits the signal to the air conditioner Then after approximately another 2 seconds the signal h disappears and the set temperature will re appear on the digital display 3 Set the starting amp stopping time 3 1 Push the TIMER ON button the remote controller will show TIMER ON the last set time for START operation and the signal h will be shown on the DIGITAL display area You are now ready to readjust the TIMER ON to start the operation 3 2 Push the TIMER ON button again to set the time you want to start the operation 3 3 Push the TIMER OFF button the remote controller will show TIMER OFF the last set time for STOP operation and the signal h will be shown on the DIGITAL display area You are now ready to reset the time to STOP operation 3 4 Push the TIMER OFF button again to set the time y
11. he ground is not level or not flat enough The sound comes from the flowing of the refrigerant inside the air conditioner Dump the water in the water tank Reset the temperature Reset the temperature Make sure all the windows and doors are closed Remove the heat sources if possible Connect the duct and make sure it can function properly Decrease the set temperature Clean the air filter Switch on again after the unit has cool down Place the unit on a flat level ground if possible It is normal CONTENTS 10 2 Remote Controller Specifications 11 3 Performance Features e eene 11 S U TOWN 4 Introduction of Function Buttons on the Remote Controller 11 5 Names and Functions of indicators on Remote Controller 12 OWNER S MANUAL 6 Operating of the Remote Controller MM 12 REMOTE CONTROLLER Note FOR PORTABLE AIR CONDITIONER 1 This operating manual is applicable to the following models of remote controller R51H R51H C 2 Model R51H is used for cooling amp heating type or heating pump type air conditioner Model R51H C is used for cooling only type air conditioner SET TEMPERATURE C F Warning AUTO FAN res 1 sure there are no barriers between the remote controller and t
12. he receiver of indoor unit otherwise the air conditioner will not work Lem um A Ud 2 Keep the Remote Controller away from all liquids C C 2 3 Protect the Remote Controller from high temperatures and exposure to radiation owjoer 4 Keep the indoor receiver out of direct sunlight or the Air Conditioner may malfunction Cc 2 5 Keep controller away from EMI Electro Magnetic Interference supplied by other household SEN NER appliances RESET LOCK a SUNPENTOWN Remote Controller Specifications Lowest Voltage of CPU 20 Emitting Signal j Reaching Distance Signal Range Environment 5C 60C 41 F 140 F Performance Feature 1 Operating Mode COOL HEAT DRY FAN and AUTO 2 Timer Setting Function in 24 hours 3 Indoor Setting Temperature Range 17 C 30 C 63 F 86 F 4 LCD Liquid Crystal Display of all functions 5 Control function of charactron tube Introduction of Function Buttons on the Remote Controller TEMP Button W Push the button to decrease the indoor temperature setting 2 MODE Select Button Each time you push the button a mode is selected in a sequence that goes from AUTO COOL HEAT and FAN as the following figure AUTO COOL DRY HEAT WT NOTE HEAT only for Heat Pump 3 RESET Button When the RESET button is pushed all of the current settings are cancelled and the control will return to
13. l the mobile air conditioner in a flat and spacious location where the air outlets will not be covered up A minimum clearance of 11 8in from a wall or other obstacles should be kept The appliance shall not be used in the laundry The plug shall accessible after appliance is positioned Wiring shall be done according to National rules 2 DUCT MOUNT INSTRUCTIONS 3 Fig 8 Exhaust Air Oulet Duck A TEMPORARY 1 Attach one end of the duct to the exhaust air outlet of the mobile air conditioner first fit the left side of the duct on the exhaust air panel then the right side duct Push it downwards be sure to fix thoroughly See the Fig 8 2 Attach the other end of the duct to adaptor B 3 Put the end of duct to a nearby window B PERMANENT 1 Attach one end of the duct to the exhaust air outlet of the mobile air conditioner According to the arrow direction 11 81in first fit the left side of the duct on exhaust air panel 5 then the right side duct Push it downwards be sure to fix Fig 9 thoroughly See the Fig 7 2 Install the adaptor A onto the wall by using 4 wall plug and screws be sure to fix thoroughly See the Fig 9 3 Attach the other end of the duct to adaptor A 4 Cover the hole using the adaptor cap when not in use The duct can be compressed or extended between 20in and 80 but it is desirable to keep the duct length to a minimum max 47 25in IMPORTANT
14. need switching on again ina short time allow approximately three minutes for the cooling or dehumidifying operations to resume Make sure the water pump drain hose is correctly connected to the unit Power supply Insert the AC Power Plug to a AC socket Do not connect the air conditioner to a multiple socket outlet which is also being used for other electrical appliance Besure the power supply is AC 115V 60Hz 2 COOLING OPERATION Operating temperature range 17 C 32 C 63 F 90 F Press the MODE button several times until the COOL indicator light comes Press the TEMP SETTING buttons A select your desired room temperature 17 C 30 C 63 F 86 F Press the FAN SPEED button to choose the fan speed 3 DEHUMIDIFYING OPERATION Operating temperature range 13 C 32 C 55 F 90 F Press the MODE button several times until the DRY indicator light comes The fan will run at a fixed speed at this setting Keep windows and doors closed for the best dehumidifying effect Do not put the duct to window 4 HEATING OPERATION Cooling only type without heat feature Operating temperature range 5 C 30 C 41 F 86 F Press the MODE button several times until the HEAT indicator light comes on Press the TEMP SETTING buttons V to select your desired room temperature 17 C 30 C 63 F 86 F Press the FAN SPEED button to choose the fan speed Do not put the duct
15. odes 2 Push the TEMP button to setthe desired room temperature When in COOLING mode the most comfortable settings are 21 C 70 F or above When in HEATING mode the most comfortable settings are 28 C 82 F or below 3 Push the FAN SPEED to select the FAN mode of AUTO HIGH MED or LOW 4 Push the ON OFF button The operation lamp lights and the air conditioner starts to operate per your settings Push the ON OFF button again to stop this unit operation A NOTE The FAN ONLY mode cannot be used to control the temperature While in this mode only steps 1 3 and 4 may be performed Q DRY OPERATION 1 Push the MODE button to select DRY 2 Push the TEMP button to set the desired temperature from 21 C 70 F to 28 C 82 F 3 Push the ON OFF button The operation lamp lights and the air conditioner starts to operate in the DRY mode Push the ON OFF button again to stop this unit operation TIMER Operation TIMER ON button can set the auto on time of the unit TIMER OFF button can set the auto off time of the unit 1 To set the starting time 1 1 Push the TIMER ON button then the remote controller shows TIMER ON the last set time for the starting operation and the signal h will be shown on the DIGITAL DISPLAY area You are now ready to reset the time to START the operation 1 2 Push the TIMER ON button again to set desired unit start time 1 3 After setting the TIMER ON there will be a one half second delay before the remot
16. ou want to stop the operation 3 5 After setting the TIMER there will be a one half second delay before the remote controller transmits the signal to the Air Conditioner Then after approximately another 2 seconds the set temperature will re appear on the digital display ANOTE 1 Please reset the TIMER after cancelling the former time settings 2 The setting time 15 relative time That is the time set 15 based on the delay of the current time Portable Air Conditioner By Sunpentown Your Guarantee If this product is found to be faulty as a result of faulty materials or workmanship within one year from date of purchase it will be repaired or replaced free of charge The compressor is covered for five year warranty This guarantee is subject to the following terms Sunpentown must be notified of the fault Proof of purchase must be presented to Sunpentown s nominated representative The warranty will be void if the product is modified misused or repaired by an unauthorized person The guarantee after repair or replacement will not be extended beyond the original one year period replacement parts or units will be new or reconditioned Parts or units which are replaced become the property of Sunpentown The warranty applied for the use ofthe product in the USA Warranty does not include freight charges Sunpentown International Inc 18249 Valley Blvd City of Industry CA 91744 Note For Service please call 1 800 330
17. the initial settings LOCK Button Push this button to lock in all the current settings To release settings push again TIMER ON Button Press this button to preset the time ON start to operate Each press will increase the time ON setting in 30 minutes increments When the setting time displays 10 00 each press will increase the time ON setting in 60 minutes increments To cancel the time ON program simply adjust the time ON to 0 00 TIMER OFF Button Press this button to preset the time OFF turn off the operation Each press will increase the time OFF setting in 30 minutes increments When the setting time displays 10 00 each press will increase the time OFF setting in 60 minutes Fig 1 increments To cancel the time OFF program simply adjust the time OFF to 0 00 ON OFF Button Push this button to start the unit operation push the button again to stop the unit operation FAN SPEED Button This button is used for setting Fan Speed in the sequence that goes from AUTO LOW MED to HIGH then back to Auto TEMP Button A Push the button to increase the indoor temperature setting Names and Functions of indicators on Remote Controller TRANSMISSION Indicator This indicator lights when remote controller Display Panel transmits signals to indoor unit MODE Display Shows the current operation AUTO COOL DRY HEAT and FAN HEAT only available for heat pump model HEAT PUM
Download Pdf Manuals
Related Search