Stiga SILENCIUM 8217-3033-01 User's Manual
Contents
1. GUARANTEE This guarantee 1s valid for one year from the date of purchase Any defects due to faulty materials or workman ship will be repaired free of charge at an authorised service station Any machine returned by the purchaser for repair must be in a clean condition Carriage costs to and from the service station are the responsibility of the purchaser This guarantee does not apply to Routine wear Careless use Personal injury or damage to proper ty Machines that have been repaired at an unau thorised workshop ENGLISH OPERATIONAL FAULTS Motor does not start Motor hums but does not start Shredding material is not drawn into the shredder Shredding material not cut cleanly Device starts but blocks under as slight load and switches off via protective motor switch No power supply Mains cable defective Machine overloaded Cutting roller blocked Capacitor faulty Incorrect switch position Shredding material caught in funnel Shredding material to soft or wet Cutting roller worn Incorrect setting of shaving plate Extension cable too long or cross section to small Socket too far from mains supply and cross section of mains cable too small Check fuses Have these checked electrician Overload protection triggered Turn On Off switch to O and let machine cool down Turn On Off switch to left then switch machine off and remove shredding ma terial2. If the blockage cannot be re moved immediately switch the On Off switch between cutting and reverse a number of times until the cutting roller runs free Bring machine to manufacturer or au thorised workshop for repair Turn On Of switch to correct position Turn On Off switch to left to release shredding material remove any dirt Push down with a branch and shred Adjust shaving plate as described in Adjusting the shaving plate replace cutting roller if heavily worn Adjust shaving plate if this cannot be adjusted it has to be replaced by the customer service department Extension cable at least 1 5 mm max imum 25 m long If a longer cable is used minimum cross section 2 5 mm
3. 8217 3033 01 Silencium ENGLISH GENERAL Your garden shredder is a high quality efficient machine Please read the following instructions carefully to ensure a long life of your garden shredder Do not operate machine before having read the operating instructions under stood all the notes and assembly the ma chine as described here PROPER USE The garden shredders are suitable for private use in gardens and allotments Regarded as garden shredders for private gardens and allotments are those units which are not em ployed in public grounds parks sports grounds and in agriculture and forestry SAFETY INSTRUCTIONS Repairs on electrical parts of the ma chine and on the safety cut out must be done by the producer or by a company designated by the producer Please read the following safety instruc tions carefully e Within his area of work the operator will be re sponsible to third parties e The machine may not be used by operators un der the age of 16 Keep children away form machine Wear protective goggles gloves and noise pro tection while working with the machine The connecting lead to DIN 57 282 H 07 RN F should be equipped with a rubber plug The lead section should be a minimum of 3 x 1 5 mn Never use faulty connecting lines Connect the machine using a fa
4. ne is overloaded a protective motor switch ensures that the machine turns itself off au tomatically turn the shredder on again after about 5 minutes during those five minutes you cannot turn the machine on See Operational faults AUTOMATIC SWITCH OVER IN THE DI RECTION OF ROTATION If the unit suddenly clogs the blades may start to turn in the opposite direction and push the shred ded material back out switch off unit wait until the blades come to a standstill switch unit back on and use material which is easier to process ADJUSTING THE SHAVING PLATE The cutting mechanism is adjusted in the works and does not have to be set during initial commis sioning Switch on device switch top right position 9 Adjusting knob o o ze ID Turn adjusting knob in a clockwise direction with the motor running until scraping noises are heard and fine aluminium chips fall out of the delivery chute Worn points on the shaving plate are opti mally compensated This improves the cutting of the shredding material MAINTENANCE AND CARE Each time before starting maintenance work switch off the motor and withdraw the mains plug wear protective gloves to prevent injury ENGLISH Generally garden shredders require little mainte nance To maintain their efficiency and a long life observe the following keep vent slits clean and free from obstructions check the locking screw
5. onnections tears cuts etc all screws are tight ENGLISH CHANGING THE DIRECTION OF ROTATION Always switch the device off wait until it comes to a standstill and shift the safety catch before chang ing the direction of rotation left position cutting rollers run back wards and release blocked shredding material right position cutting rollers draw in and cut shredding material safety catch Switch on Turn On Off switch to T Switch off Turn On Off switch to 0 CHOPPING What can I chop Yes all types of branches withered garden refuse which has lain a num ber of days Only shred in alternation with branches hard wood though only with sharp cutter No glass metal plastic plastic bags stones cloth roots with soil refuse which does not have a solid consistency e g kitchen waste SPECIAL TIPS ON CHOPPING Please do not exceed the maximum branch diame ter specified for your appliance see page 38 Branches twigs and wood should be broken down immediately after they have been cut Material of this kinds gets very hard when it is dry and it there fore makers sense to reduce the maximum branch diameters so that it is ready for chopping Remove any side shoots from branches with a large number of twigs The cutter automatically draws the shredding ma terial into the machine through the slow rotation of the cutting rollers If the machi
6. s tighten where ne cessary clean the device after shredding the shredder should not be cleaned with high pressure cleaners or running water treat the cutting roller after every use with a biodegradable spray oil as protection against corrosion the cutting roller and shaving plate are ex pendable parts though with normal use and correct adjustment they have a service life of many years SPECIFICATION Name of model AH 280 Motor AC motor 230 V 50 Hz S6 40 ED 2800 40 min On Off switch With overload protection With cutting and reverse function Acoustic pressure level at work Lpa 79 dB A Measured to RAL UZ 54 DIN 45635Teil 1 05 84 Acoustic capacity level Lwa 86 dB A Measured to RAL UZ 54 DIN 45635Teil 1 05 84 Max branch diameter only for fresh cut wood I Safety class SERVICE Authorised service agents carry outrepairs and service They use genuine spare parts Do you do basic repairs yourself Then make sure you use genuine spare parts They fit immediately and make your task easier When ordering spare parts please state the model part number and serial number This information 1s on the rating plate on the machine Do not fit any parts other than genuine A spare parts This is a requirement of the Testing Institute The machine has been tested and approved with these parts The manufacturer reserves the right to modify the prod uct without prior notice
7. ult current pro tection switch Always switch off motor before maintenance and cleaning of shredder Remove mains plug from socket also during transport and when leaving machine unattended Do not operate without the funnel e Faulty or damaged parts in the device must be replaced immediately e Never reach into the filling or ejection opening when the machine is running e Do not spray machine with water this is haz ardous due to live components e Wear safety gloves during assembly and clean ing work e Never modify the machine or parts thereof e Only use the machine for the purposes listed un der Section Chopping e Do not leave the machine standing in the rain or use when raining Store the machine in a dry place ASSEMBLY See pages 4 5 Use the enclosed disposable screws MS x 16 to fit the funnel a to the pre assembled machine b Otherwise no li ability will be assumed START UP Check that the machine is completely and correctly assembled To avoid toppling place the chopper on a firm hor izontal surface Connect the machine to an appropriate and correct ly wired electric socket Only use extension leads with sufficient diameters cable up to 25 metres diameter at least 1 5 mn cable over 25 metres diameter at least 2 5 mm Fuse protection for model 2000 16 A inert Before using the shredder make sure each time that there are no faulty c
Download Pdf Manuals
Related Search