Star Trac FITNESS E-TBTi User's Manual
Contents
1. Gate dow ae oe MA i ae 33 SOUNA MENU ee eae eo ee eee ee ae ee oe 34 Socii Mete cana ea HUM Uu RE 35 FAQ s and Troubleshooting 16 ED iu Hee RE ee Ra ees dau 37 CIE AMINO FVS pin EET RT TETTE RTT T EET D T peeled ok Ae LL 37 TOUDICSNOOUNG ek eain ac ace o asd nee a haw eq atc dia uod cal o ac adie 37 Ihe Headphone Jack iudex bee tae ee teh eee NACE Reni ORE Er irl do apa 39 Regulatory Information 34 4d es Re elo or ica da ade ed rode uer DOE Pa tod ue sara ee Lad 40 Copyright 2008 Star Trac by Unisen Inc All rights reserved including those to reproduce this book or parts thereof in any form without first obtaining written permission from Star Trac Every effort has been made to keep this information current however periodically changes are made to the information herein and these changes will be incorporated into new editions of this publication All product names and logos are trademarks of their respective owners Printed in the USA 2 STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE INTRODUCTION Thank you for adding the STAR TRAC PERSONAL VIEWING SCREEN PVS to your Star Trac Pu2. 9 Installing Your STAR TRAC Personal Viewing Screen PVS 10 E DUB E RB E TIBI 517 5 x p rorem rosse dea E HE oe URS Rue Sec ate 10 OQ ee done E ioe 18 Setting Up Your STAR TRAC Personal Viewing Screen PVS 24 ypically US Japan 2 os M rete Rr E aad od eee EE LEE 24 Accessing the WISTS d a o redu o mL ts AE LM o CR D Nuda Wed 24 Sening UP ithe Channels 2 eee e ER eee eh tS aos bower RE Spi PIRE rate dunes utt 25 Adiusung Mage Qualys 2 2 2 ue cat wo cae nor cc oe beth Gd au vr ane e pati is 27 five Avdi Qualy M Sen I ccr 28 Adjusting Special features 29 PAL SECAM typically Europe Middle 30 Maintenance Mode for uestes oe PLA EX Ea Ea pe etal oes 30 Maintenance Mode for E TBTi E STi E RBi and E UBi 31 Accessing On Screen Display Menus OSD 32 PICTURE
3. SET TIME It is recommended that you set the Time Set Mode to Manual Adjust all other settings as desired SLEEP MODE TIMER Will allow you to tell the screen to turn of 30 60 or 90 minutes from activation OSD TRANSPARENCY Adjusting transparency of all OSD such as program information Volume control amp channel edit etc Except main Menu OSD above picture SET PASSWORD Allows you to put a menu access password Enter a four digit code with the keypad and then press OK PARENTAL CONTROL Digital broadcasting includes several ratings grades This feature will allow you to set which ratings or grades to block DISPLAY CAPTION OPTIONS Allows you to adjust how you would like the captions to appear STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE 29 PAL SECAM Personal Viewing Screen Set up QUICK QUICK STOP START START CHANNEL SELECT CHANNEL SELECT VOL CH TRK 1 2 3 VOL CH TRK DAG Pa O 999 DOS BS JU J OO Yv Before you can set up the Personal Viewing Screen you must first get into the Maintenance Mode of the Star Trac Cardio Equipment while is this mode you will tell the equipment what type of Personal Viewing Screen you are installing For the Maintenance Mode on the E TR follow the steps below 1 Press and hold the 2 keys together the display keypad of the Cardio Equipment 2 A beep will sound and MAINTE
4. Provides regulatory information for the Star Trac Personal Viewing Screen 4 STAR TRAC PERSONAL VIEWING SCREEN OWNER s MANUAL BEFORE YOU GET STARTED CHECK FACILITIES PREPAREDNESS For a proper installation please read this guide thoroughly and follow the instructions Star Trac s goal is to help you have a successful and reliable installation for this reason we have come up with some helpful tips and check list to accomplish this goal EQUIPMENT LAYOUT Check to see that the equipment you will be adding the PVS to are place where they will be used It is recommended that you follow your installation guides for each one of your Star Trac pieces of equipment in making sure that there is ample space around them to insure a safe and enjoyable experience INPUT SIGNAL In the world of entertainment today you have many choices Star Trac recommends you know what type of video signal cable analogue digital satellite antenna is in the club facility and if it has a good signal Don t forget every installation is different Check to see that you have ample video coaxial cable connections to the locations where the PVS will be installed CABLING When Radio Frequency signals travel through cabling the signal will degrade over distance Connectors may degrade the signal as well Check each output before connecting to your PVS and make sure you have a clean strong signal to insure an enjoyable experience The Star Trac PVS requires
5. will display in the Information Window The following keys are available in MAINTENANCE SETTINGS Upper and Lower Data Information Window ScRoLL Keys Display the next and pre vious parameters respectively Keys will repeat if held Increase and Decrease LeveL Keys Adjust the value of the displayed parameter up and down respectively in increments of 1 unit These keys do not save the new value see OK Key below OK Key Updates saves the value of the displayed parameter in Flash memory and exits Maintenance Mode NOTE To exit Maintenance Mode without saving any values or settings press the Quick START key The items that you may display and change with the previous keys are 4 Press either to navigate to the PVS variable 5 Press the level up to change the variable from ATCS NTSC to PAL SECAM 6 Press the to save the change and exit This completes the E TBT E ST E RB and E UB setup now turn to Accessing The On Screen Display to continue STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE 3l PAL SECAM ACCESSING THE ON SCREEN DISPLAY OSD To enter the On Screen Display OSD setup menu you need to press and hold the voL and on and at the same time press the the Entertainment Center Console keypad The On Screen Display requires either a strong video signal or no video signal If you are unable to get into the On Screen Display try changing the channel if that does not work discon
6. Auto Search then press the LJ to start the Auto Search This will scan for channels and exit the OSD STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE 35 PAL SECAM SETTINGS MENU Clock On Time PM05 57 Off AM12 00 Off AM12 00 Off West English Off Time SleepTimer TTX Language OSD Language lt lt lt lt lt lt lt v gt Select E xit This menu is for adjusting the following items Clock PVS clock time On Time On time Off Time Off Time SleepTimer Enable on off timers TTX Language Timed text OSD Language On Screen Display Language Use the UJ to navigate to the Sound menu To enter the sub menu press Use the 28 and Jg to navigate to the desired sub menu Use the Jg to select the element you wish to modify Once a sub menu element is selected use the GJ to modify that item When you are finished with that item press the to exit that item Use the g to select a different element or press the J to exit the sub menu and return to the Main menu 36 STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE FAQ s AND TROUBLESHOOTING Your Star Trac Personal Viewing Screen is designed with little maintenance in mind and rarely should you experience a problem once it is installed However you may find the cleaning and troubleshoot ing information in this section useful We
7. a minimum signal strength of 45dBmV for analogue channels and 40 for digital channels Your club may require signal amplifiers to achieve a good strong signal Star Trac recommends you use a qualified installer for your Audio Visual needs ELECTRICAL RECEPTACLES The Personal Viewing Screen requires a plug in 60 watt power supply to operate included Check with your club facility to ensure ample electrical receptacles are placed next to the equipment for a safe and proper install Check with your con tractor to make sure you have enough power STAR TRAC PERSONAL VIEWING SCREEN OWNER S MANUAL 5 WARNINGS AND CAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR PRECAUCION RIESGO DE CHOQUE ELECTRICO NO ABRIR CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This lighting flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons This exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instruction in the literature accompanying the appliance WARNING To reduce the
8. are finished with that item press the to exit that item Use the g to select a different element or press the J to exit the sub menu and return to the Main menu 34 STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE PAL SECAM SETTING UP THE CHANNELS Country amp Others Search Option v All Auto Search Py Manual Search A Manual Search D Time Offset lt gt Select ENDE xit This menu is for adjusting the following items Country Provide a list of country settings supported by PVS Search Option All FTA Scramble Auto Search Press OK to start Auto Search Manual Search A Used to manually Scan and add selected channels Manual Search D Used to manually Scan and add selected channels Time Offset From 12 00 to 12 00 Use the g to navigate to the Sound menu To enter the sub menu press Use the and to navigate to the desired sub menu Use the g to select the element you wish to modify Once sub menu element is selected use the 9 g to modify that item When you are finished with that item press the to exit that item Use the of es to select different element or press the to exit the sub menu and return to the Main menu AUTO Search Use this feature to automatically scan your service and add channels to the PVS To do this follow this procedure Use the 981 or to navigate to the
9. be connected to the display Use the image below to help reference the needed points on the display 12 Pin Connector 4 RCA Connector Center Console Ground Connector STEP 14 Take the coax cable from the PVS mount and attach it to the coax cable on the base unit Tighten the connectors snug to each other STEP 15 Take the 5 piece of tape from the PVS kit and wrap the connectors so that all of the metal surface is covered 14 Heart Rate Ground Connector Heart Rate Connector 2 DC Power PVS Remote Connectors Connector lt d e Coax Cable SHALE STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE STEP 16 Using wrap from the PVS kit bind the cables from the PVS neck to one side of the display mount Take the tie and put it through the hole on one of the display mount tubes STEP 17 Now take the front display plastics with the new Center Console to the base unit Hold the front display plastics at the top with one hand while con necting the cables harnesses with the other There 5 particular order in connecting the cables harnessing However it may be best to start off connecting the cables harnessing coming from the neck of the base unit STEP 18 CABLES to be connected Refer to drawing on previous page for connection points on the display front Connect the 12 pin serial cable from the base frame neck to the O 12 pin socket on the display e
10. sure the correct INPUT is selected by pushing the INPUT button Make sure your signal source is prop erly connected Try changing channels it may be a station problem Turn off the PVS and then back on after one minute Menudo Increase the audio level with the Make sure the Headphone jack is secure Replace Headphone jack if necessary STAR TRAC PERSONAL VIEWING SCREEN OWNER S MANUAL 37 Bars Snow the screen Poor TV reception Ghost in the picture Missing TV Channels Center Console Keypad seems unresponsive No Signal displayed on screen PAL SECAM Display Unable to get into the OSD 38 Check the input signal cable make sure it is in good shape and is con nected snug to the RF input Adjust the Brightness Hue Sharpness and Contrast in the Video Setup of the PVS Check the input signal cable make sure it is in good shape and is con nected snug to the RF input Try a new channel it may be the station is having difficulties Check for local interference Check the input signal cable make sure it is in good shape and is con nected snug to the RF input Try a new channel it may be the station is having difficulties Check for local interference Try adjusting the Sharpness in the PVS video setup Check the input signal cable make sure it is in good shape and is con nected snug to the RF input Try a new channel it may be the station is having di
11. Connect the Heart Rate cable from the display support tube to the Heart Rate board on the display e Connect the DC power from the base frame neck to either one of the DC connec tors on the front display center console board e Connect the DC power from the PVS display neck to the other DC connector on the front display center console board Connect the Remote cable from the PVS display neck to the O Remote connector on the front display center console board e Connect the RCA cable from the PVS display neck to the 4 connector on the front display center console board Connect the Ground cable from the front display 2 Heart Rate board to one of the ter minals on the display mount Connect the Ground cable from the front display 5 Center Console to one of the ter minals on the display mount STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE 15 STEP 19 Feed the Head Phone Jack cable from the PVS display neck through the hole in the front display plastics where the blank cover was removed earli STEP 20 Now that all the cables their places fined to the post on the display mount Place the display front plastic onto the back Make sure the bottom of the display front is under the 2 tabs on the display mount Press the front display against the round tube and rotate it to the back Be care ful not to pinch any wires STEP 21 Using a 2 Phillips screwdriver secure the
12. EEN PVS UNPACK YOUR PERSONAL VIEWING SCREEN Inspect the shipping carton for any parts that may be missing BEFORE discarding the carton Items can shift during transportation and may be accidentally discarded with the carton If any parts are missing please contact Star Trac Product Support at 800 503 1221 Have the serial number of the PVS and a list of the missing parts ready so they may be shipped to you The Personal Viewing Screen is shipped in one box separate from your exercise equipment The following items will be in the box PVS kits are available in two different signal formats NTSC ATSC typically US Japan and PAL SECAM typically Europe Middle East make sure the kit you have is appropriate for the country of the club facility NTSC NTSC ATSC Kit US Japan NOTE there are 4 different kits ie E TRi E TBTi E UBi E RBi AND E STi PVS assembly with Mounting Bracket Cables and Display Cap with Grommet There are 5 cables in the neck Center Console Keypad Assembly Entertainment Headphone Jack and Mount 2 5 Tie straps 2 M8 x 20mm Buttonhead Screws 1 M8 x 20mm Buttonhead screw E TRi only 1 M8 Nut E TRi only 60w Power Supply Power Cord AS NZS 3112 NOT INCLUDED IN THE E TRi KIT STAR TRAC PERSONAL VIEWING SCREEN OWNER s MANUAL Power Cord 6 15 NOT INCLUDED IN THE KIT Power Cord 5 15 INCLUDED IN THE E TRi KIT e Owners Manu
13. NANCE will display momentarily in the Information Window Release the keys MCI VX XX will display in the Information Window The following keys are available in MAINTENANCE MODE Incline Keys Displays the next and previous parameter respectively Keys will repeat if held Speed Keys Adjust the value of the displayed parameter up and down respectively in increments of 1 unit or 0 01 unit as appropriate for the parameter These keys do not save the new value see Key below Enter Key Updates saves the value of the displayed parameter in Flash memory Alternatively the key may be used see above Number Program Select Keys Enter new data item values for numeric parameters Stop Key Exits Maintenance Settings Mode and restarts the treadmill greeting 4 Press the AA incline up to navigate to the PVS variable 5 Press the HA speed up to change the variable from ATSC NTSC to PAL SECAM 6 Press the to accept the change 30 STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE 7 Press the X to exit This completes the E TR setup now turn to the Accessing The On Screen Display to continue For Maintenance Mode on the E TBT E ST E RB and E UB follow the steps below 1 Press and hold the keys together 2 Abeep will sound and MAINTENANCE SETTINGS will display momentarily in the Information Window 3 Release all keys SERIAL NUMBER
14. STAR TRAC 55 PERSONAL VIEWING SCREEN OwNER s MANUAL expect different TABLE OF CONTENTS IDITOOHC sus s dr d oan eru Ease dat a me su Mane Sm NT iude mIRC ete 4 ADOUE THIS Manual uui e od d e decet xe e e od ote ee Owe at ard ace V actu d Vor de era 4 Betore You Get Slanted RE DER Rorate gd a Rate Ed ac app 5 Check Facilities Preparedness 5 2265 MP 5 MPULSIGMAlS ee Eee eee es 5 E AN 5 Power Receptacles 5 Warnings and lt MAGES nadine 6 STAR TRAC Personal Viewing Screen PVS 8 Unpack WOU TS rur 8 215204 coc eS ohare hae 8 PALISECAMW deel eh ee 8 Too Needed X NCC Gene We we
15. able in the jack opening Use the previously retained screw to reinstall the Headphone Jack Tighten snugly Phone Jack STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE 21 STEP 13 From below the display connect the Center Console Ground Cable to the Q Quick Disconnect Tab on the display mount Connect the Keypad Tail to the Keypad con nector on the display PC board Connect the Interface Cable to the Interface connector on the display PC board STEP 14 Go to the base of the treadmill neck Using a 2 Phillips screwdriver remove the 2 screws that hold in the RF cable Mounting Bracket Retain the screws for later use STEP 15 Remove the nut and washer from the F Type con nector on the end of the coax cable you fed down the treadmill neck then put connector through the Mounting Bracket Replace the nut and washer and tighten the nut snugly Next replace Mounting Bracket into the neck using the screws retained from previous step Tighten with a 2 Phillips screwdriver STEP 16 Replace the bottom back plastic Using a 2 Phillips screwdriver insert the 6 screws retained from earlier step into the plastic and tighten snug Caution Do Not over tighten screws 22 Screws Mounting P i Bracket ae WT L ua my SS YA 11 Screws Screws STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE Screws Screws STEP 17 Replace the top back plastic U
16. al PAL SECAM Kit Europe Middle East NOTE there are 4 different kits ie E TRi E TBTi E UBi E RBi AND E STi PVS assembly with Mounting Bracket Cables and Display Cap with Grommet There are 5 cables in the neck Center Console Keypad Assembly e Entertainment Headphone Jack and Mount 2 5 Tie straps 2 M8 x 20mm Buttonhead Screws 1 M8 x 20mm Buttonhead screw only 1 M8 Nut E TRi only e 60w Power Supply F Type to PAL SECAM Coaxial Adapter Power Cord 7 7 NOT INCLUDED IN THE E TRi KIT Power Cord 6 15 NOT INCLUDED IN THE E TRi KIT Power Cord BS 1363 NOT INCLUDED IN THE E TRi KIT e Owners Manual Required Tool for Installation Supplied 5MM Hex Allen Key Not Supplied e 2 Phillips Screwdriver 1 2 Wrench for E TRi Kits only e Wire Cutters e Step Stool STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE INSTALLING YOUR PERSONAL VIEWING SCREEN PVS The Star Trac Personal Viewing Screen is different for each of your Star Trac E Series Cardio prod ucts Make sure you have the proper kit for the E Series product you are installing The E UBi E RBi E TBTi and the E STi will follow the same basic steps for installation For the E TRi turn page 18 in this section To install on the E UB E RB E TBT and the E ST follow these steps STEP 1 Using a 2 Phillips screwdriver remove the 8 screws on the back of the display plastic Set the screws
17. aside you will need them for reassembly STEP 2 After the screws have been removed carefully open the display plastic so as to not detach the inner cables from the display Disconnect the ground wire C between the Heart Rate board and the display mount STEP 3 Disconnect the 12 pin serial connector 2 and the Heart Rate cable 3 from the display falis 10 STAR TRAC PERSONAL VIEWING SCREEN OWNER s MANUAL After all the cable harnessing has been disconnected place the front display plastics aside for later use Be careful with the display and place it face down on top of a non scratching surface STEP 4 Remove the cap cover with the Star Trac logo from the plastics by removing the 2 screws using a 2 Phillips screwdriver Retain the screws for later use You will no longer need the cap cover and if desired you can store it away for any possible future use STEP 5 Remove the 2 M8 buttonhead screws retaining the crossbrace using the 5mm Hex Key found in the hardware kit Retain the screws for later use You will no longer need the crossbrace and if desired you can store it away for any possible future use STEP 6 It is now time to install the Personal Viewing screen Remove the PVS with its mounting brack et and cables from the packaging Also remove the 2 8 buttonhead screws from the hardware kit in the packaging STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE You can use the f
18. dify that item When you are finished with that item press the to exit that item Use the of ER to select different element or press the J to exit the sub menu and return to the Main menu This menu is for adjusting the following items Picture Mode Brightness Adjust to brighten or darken the picture Contrast Adjust the white level of the picture Sharpness Adjust to sharpen or soften the picture Saturation Adjust Saturation of the picture Tint Adjust color tone Color Temp Default to NORMAL Aspect Ratio Image size on screen Default to NORMAL STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE 33 PAL SECAM SETTING THE SOUND Sound Mode Standard gt Bass Treble 5 5 MTS e MONO Off gt Select ENDE xit This menu is for adjusting the following items Sound Mode Default is Standard Bass Will adjust the bass tone of the sound output Treble Will adjust the treble tone for the sound output Balance Will adjust the sound volume between the right and left ear MTS Multi Channel Television Sound ANC Auto Volume Control Use the UJ to navigate to the Sound menu To enter the sub menu press Use the 28 and Jg to navigate to the desired sub menu Use the Jg to select the element you wish to modify Once a sub menu element is selected use the GJ to modify that item When you
19. emove the 8 screws from the upper back of the display Place the cover somewhere safe to keep it from being damaged Next remove the 6 screws from the lower back of the display Place the cover with the other one Retain all the screws for later use STEP 2 Now remove the upper cap cover that has the STAR TRAC logo on it This cap is held in by the upper back cover You will no longer need this cap cover and if desired you can store it away for any possible future use STEP 3 Using a 2 Phillips screwdriver remove the screw that holds in the Blank Head Phone Jack Cap at the lower front of the display Retain the screw You will no longer need the cap and if desired you can store it away for any possible future use Now take the Entertainment Head Phone Jack from the PVS hardware kit Use the previously retained screw to reinstall the Headphone Jack Tighten snugly 18 Cap 7 d New Head Phone Jack STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE STEP 4 Detach the Center Console Ribbon Cable from the display board by gently pulling on the ribbon con nector Using a 2 Phillips screwdriver to remove the 4 screws that hold the center console in place Retain the screws for later use Remove the center console You will no longer need this center console and if desired you can store it away for any possible future use STEP 5 Take
20. ewdriver remove the screw that holds in the blank cover where the new Head Phone Jack mount will go Next remove the blank cover You will no longer need this item and it can be stored away for any possible future use Retain screw for later use STEP 11 Take the PVS center console from the kit STEP 12 Insert the new center console into the front display Using a 2 Phillips screwdriver screw in the 4 screws that were saved from the original center console Tighten the screws so they are snug STEP 13 With the center console now installed it is time to attach the interface cable and center console rib bon Take the seven pin interface cable from the center console and attach it to the display PC board Next take the center console ribbon cable and attach it to the display PC board STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE ni Center Console Interface Ribbon Cable Make sure pin one on the cable is connected to pin one on the board 13 With the changes now completed the display it is now time to re install the display to the base unit There are the 3 cables from the PVS mount that will need to be attached to the display One cable from the PVS mount will be fed through the display which will be connected to the head phone jack later The fifth cable from the PVS mount which is the coax will be connected to the coax on the base unit There are 2 cables from the base unit that will
21. fficulties Check for local interference Check the Channel setup of the PVS The specific channel may not be programmed If necessary rerun the Auto Channel feature in the PVS setup Check to see that the ribbon cables are connected firmly and properly rib bon may be reversed Check Center console PC board LED will be green or red if there is no light the center console it is not receiving any power Check to see if the Maintenance Settings PVS value is set to the proper PVS type See Setting up your Star Trac PVS see NO PICTURE You may have to rerun the setup routine for the display Check that all input values are correct for you service provider Press the input to change from AV input to RF input Push Channel UP or Down to see if you are getting any clean channels Turn Display off then wait for a minute and turn back on Disconnect the RF cable get into the OSD and reconnect the RF cable STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE Headphone Jack Replacement When you are experiencing poor audio output from your PVS you should check the entertainment headphone jack to see if it needs replacement The headphone jack was designed for an easy and quick replacement Before you begin make sure your have the proper replacement part available For the E TRi use part number 715 3668 For the E TBTi E STi E RBi and E UBi use part number 718 5098 Look under the Display unit in the front you
22. from analog broadcasting As for digital however weak signals or signals without broadcasting info are ignored MANUAL CH SET Move to a channel you want by using cH 9 gt Push to change between Viewable Not Viewable and Favorite Favorite will act the same as Viewable When you are finished modify ing the Channel set press 2 3 at the same time to exit this menu and return to the Channel Sub Menu 26 STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE CHANNEL LABELS You can change the channel labels for each of the viewable channels Analog channels are shown as because there is channel name info Digital channels without channel info will also be dis played as Some channels of digital broadcasting may be misnamed Use the 98 1 CJ to navigate between channels Use the and gt the next letter of the selected channel or back to the channel selection area Once you are in the label area use and J to scrol through the Alpha Numeric Use to move to the next space When you are finished labeling the channels you want press the to return to the Channel Sub Menu MENU LANGUAGE Push to change between Menu Languages English French and Spanish Menu Language changes as you select but the Main Menu remains in English NTSC ADJUSTING IMAGE QUALITY VIDEO MENU Contrast Brightness Sharpness Color Tint Color Te
23. front display to the back with the 8 screws you previ ously removed and saved STEP 22 Take the Entertainment Head Phone Jack from the PVS kit and attach it to the cable that is hanging out of the front of the display Make sure the con nector is seated all the way into the jack Now slide the jack into the front of the display Using a 2 Phillips screwdriver fasten the head phone jack into the front display with the screw that was saved from the earlier step 16 Screw STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE STEP 23 Now with the Personal Viewing Screen installed on your Star Trac equipment it is time to connect your entertainment cable and power to the unit Look at the bottom of the neck next to the floor Connect your in house Entertainment cable to the RF input Take the power supply from the PVS kit and plug the small barrel connector to the DC input Now take the appropriate Power Adapter Cable from the kit and plug it into the power supply and the elec trical receptacle Only use the power supply that was provided in your Personal Viewing Screen Kit Using the wrong supply may damage your PVS This completes the installation of the Personal Viewing Screen Now it is time to set it up Turn to the appropriate section for your Personal Viewing Screen STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE 17 To install the E TR follow these steps STEP 1 Using a 2 Phillips screwdriver r
24. moerature Normal Aspect Ratio Normal Settings Preset Select Exit The Video Menu on you Personal Viewing Screen is much like any standard Video display This section will allow you to change the visual look of the screen Use the 28 move between selections Press the to enter the the selected item Use the and J to adjust the item when you are finished press to return to the Video Menu CONTRAST Adjust the white level of the picture STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE 27 BRIGHTNESS Adjust to brighten or darken the picture SHARPNESS Further you go left more the screen softens and further you go right more the screen sharpens Caution When sharpness is too high video noise soars in some videos which may cause problems in image quality Normal setting is recom mended COLOR Adjust to increase or decrease the Color intensity TINT Adjust color tone COLOR TEMPERATURE Default to NORMAL ASPECT RATIO Image size on screen Default to NORMAL SETTING When you execute this menu all video related values which were previously set will reset to the factory default NTSC ADJUSTING AUDIO QUALITY AUDIO MENU Audio Language English Bass ceo Treble 5o Balance L Digital Audio Output Raw Settings Preset The Audio Menu will allow you to adjust the sound features for your Personal Viewing Screen Use the or 28 g move between selections P
25. nect the RF cable at the base of the unit Main Menu Sub Menu Menu Name Picture Mode User Brightness T Contrast ELEEELELLLE Sharpness Tint Color Temp Normal 5 Saturation 5 Aspect Ratio lt Zoom gt gt Select ENDExit Below you will see the setup screen for the PAL SECAM unit with its window descriptions Follow the step by step directions to set up your screen Use the 9 g to navigate between Main menu items To enter a sub menu press 9 nd oaeee press LJ Once you are in a sub menu use the 9 J to navigate between sub menu items Press the Jg to select an element to modify To increase or decrease a selected item use the and 9 When finished press the to exit that element Press the 7 J to exit the sub menu 32 STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE PAL SECAM ADJUSTING THE ON SCREEN DISPLAY Picture Mode User Brightness Contrast Sharpness Saturation Tint Color Temp Normal Aspect Ratio lt gt Select ENDE xit PICTURE MENU Use the LJ to navigate to the Picture menu To enter the sub menu press voL Use the and to navigate to the desired sub menu Use the Jg to select the element you wish to modify Once a sub menu element is selected use the UJ to mo
26. oam bag that ships inside the Personal Viewing Screen package to place the display face onto This will help protect it from being damaged Screws 7 11 7 Install the 4 M8 Buttonhead Screws through the PVS mounting bracket into the display mount Note 2 of the screws are in the PVS kit 2 retained from step 5 Do not tighten them at this time Screws EN STEP 8 Adjust the cap with the grommet into place Using the 5mm Hex Key tighten the M8 Buttonhead ocrews to 190 Ib in 21 5 N m of torque Take the 2 Phillips head screws you removed from the original cap and snugly tighten screws down using a 2 Phillips screwdriver Check the back side of the display to see that the cap is seated properly If not loosen the two Phillips Head Screws adjust the cap and then retighten the screws STEP 9 It is now time to make changes to the front display Disconnect the center console ribbon cable from the back of the display PC board Using 2 Phillips screwdriver remove 4 screws that hold the center console to the main display Retain Z screws for later use Detach the center console mm S from the display You will no longer need this item and it can be stored away for any possible future use Ellin 100009 w PEN P 4 Screws Ribbon Cable 12 STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE STEP 10 Using a 2 Phillips head scr
27. rchase The Personal Viewing Screen has been designed to provide the user with the most rewarding experience based upon the carefully planned features it possess The design elements of this Personal Viewing Screen will provide you with a comfortable intu itive safe and reliable experience guiding you to a habit forming lifestyle Star Trac s mission is to provide products to mold lifelong habits for health and fitness ABOUT THIS MANUAL This manual is applicable to the STAR TRAC E UB UPRIGHT BIKE E RB RECUMBENT BIKE E ST STEPPER E TBT TOTAL BODY TRAINER and the E TR TREADMILL The manual is divided into eight sections as follows Introduction Provides an overview of each section within the manual Before You Get Started Provides guidelines to help you have a successful installation Warnings and Cautions Helpful safety tips to keep you out of harms way STAR TRAC Personal Viewing Screen PVS Provides a description of what you will find in your PVS kit Installing Your STAR TRAC Personal Viewing Screen PVS Provides a step by step instruction set for installing your PVS on the E UB E RB E ST E TBT and E TR Setting Up Your STAR TRAC Personal Viewing Screen PVS Provides step by step instruction set for configuring your PVS with either the NTSC ATSC or PAL SECAM screen FAQ s and Troubleshooting Frequently asked questions and troubleshooting methods to help solve problems that may occur with your PVS Regulatory Information
28. ress the to enter the the selected item Use the r adjust the when you are finished press to return to the Audio CH Menu AUDIO LANGUAGE Audio Language supports digital broadcast audio as digital broad casts may include several channels of audio Note In some digital channels audio lan guage is not English although English is set as audio language It can be regarded as an error in terms of broadcasting information but there should not be any problem func tioning BASS Will adjust the bass tone of the sound output 28 STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE TREBLE Will adjust the treble tone for the sound output BALANCE Will adjust the sound volume between the right and left ear DIGITAL AUDIO OUTPUT Push the OK button and it changes to PCM or RAW SETTINGS When you execute this menu all Audio related values which were previ ously set will reset to the factory default NTSC ADJUSTING SPECIAL FEATURES SETTING MENU Set Time Sleep Mode Timer Off OSD Transparency Opacity Set Password Parental Control Closed Caption Options Display Closed Caption Select Exit The Setting Menu will allow you to adjust the special features for your Personal Viewing Screen Use the 7 g move between selections Press the to enter the the selected item Use the to adjust the item when you are finished press to return to the Setting Menu
29. risk of fire or electric shock do not expose this appliance to rain or moisture CAUTION These service instructions are for use by qualified service personnel only to reduce the risk of electric shock DO NOT perform any servicing other than that contained in the operating instructions unless you are qualified to do so 6 STAR TRAC PERSONAL VIEWING SCREEN OWNER S MANUAL This STAR TRAC Personal Viewing Screen has been engineered and manufactured to assure your safety Before using this product be sure to read your user s manual in order to maximize the life of your display DO NOT disassemble the PVS Any Un authorized maintenance will void the warrenty Un experienced technicians can cause serious damage electric shock and other hazards Contact your dealer or an experienced technician for repair DO NOT place sharp tools such as pin or metallic object near the display May result in scratching the surface of the monitor as well as the frame Keep your monitor away from liquid or a humid place May cause electric shock and damage the display DO NOT spray any fluid directly on the surface of the monitor Spray the cleaner fluid on a soft cloth to wipe the surface of the monitor When strange sound or smoke occurs be sure to unplug your power cord These problems can cause a serious electric shock and other hazards STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE 7 STAR TRAC PERSONAL VIEWING SCR
30. setup screens Refer the remainder of this section for a more complete description of each sub category STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE 25 TUNING BAND Air Use this selection when a terrestrial indoor outdoor antenna is used Cable Use this selection for standard analogue cable Consult cable provider of cable type prior to set up HRC Harmonically related carriers IRC Incrementally related carriers CABLE AUTO Use to automatically sense the cable type CABLE MODE When you set Tuning Band to CABLE your menu selections will change Cable mode will set the type of cable service you are using Consult cable provider for cable type For digital cable VSB QAM is supported depending on transmission system When QAM is set 64 256 QAM is automatically detect ed and set VSB When transmission is 8VSB set cable mode to VSB QAM When transmission is 64 256 QAM set cable mode to QAM NONE When Digital cable is not used set cable mode to NONE This works only when Tuning Band is set to cable For digital cable please check whether the transmission system is 8VSB 64QAM or 256QAM with your cable provider In addition encrypted signals cannot be displayed AUTO CH SEARCH Navigate to the Auto CH Search and push the button Broadcasting frequencies are automati cally searched and saved The search starts from analog broadcasting to digital and it takes 2 4 min Channel numbers are allocated for weak signals
31. sing a 2 Phillips screwdriver insert the 8 screws retained from earlier step into the plastic Do Not tighten at this time STEP 18 Check the cap with the neck and grommet Make sure the cap is flush with the top back plastic Adjust if necessary Use the screwdriver to tight en the screws snug from the previous step Caution Do Not over tighten screws This completes the installation of the Personal Viewing Screen on the E TR treadmill Now it is time to set it up Turn to the appropriate section for your Personal Viewing Screen STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE 23 SETTING Up YOUR PERSONAL VIEWING SCREEN Now that your Personal Viewing Screen is installed on your Star Trac Cardio Equipment it is time to set it up There are 2 types of Personal Viewing Screens turn to the section that applies to your unit NTSC ATSC Personal Viewing Screen Set up QUICK QUICK STOP MM CHANNEL SELECT CHANNEL SELECT VOL CH TRK eae J EJ OO E UBi E RBi E STi AND E TBTi enter the setup menu you need to press mE 3 on the Center Console key pad at the same time Below you will see the basic screen for the unit with its window descriptions Follow the step by step directions to set up your screen Tuning Band Cable Mode Sub Menu M a n M e n u Manual Setting Channel label Options Menu Lang
32. t into a separate outlet that uses a different circuit than the receiver Consult a Star Trac Service Representative or an experienced radio TV technician for help Warning Per FCC rules changes or modifications not expressly approved by Star Trac could void the user s authority to Operate the equipment 40 STAR TRAC PERSONAL VIEWING SCREEN OWNER S MANUAL STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE 4 GZ TRAC expect different STAR TRAC 14410 Myford Road Irvine California 92606 Telephone 800 228 6635 714 669 1660 Fax 714 508 3303 http www startrac com email support startrac com Part Number 620 7838 REV A July 2008
33. ter Console 7 NL Ground PVS Remote Connector RCA Connectors _ ES Backside of Entertainment Center Console 2 DC Power Connectors 20 STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE STEP 10 While holding the New Center Console near the opening of the display connect the following cables to there approprate connector There is no particular order Plug in the 2 DC power cables to the 2 DC connectors they are the same so it does not matter which goes to which Plug in the PVS Remote Cable to the PVS Remote Connector Plug in the RCA Cable to the Video 6 pin and the Audio 2 pin connector respective ly RCA Connectors Take the Keypad Tail and the 7 Center Console Ground feed them through the O Cable Window STEP 11 Screws Screws Close the Center Console Using a 2 Phillips screwdriver take the screws retained from earlier and screw in the 4 screws from below that hold in the center console Tighten the screws snug STEP 12 Note If you have E TR skip this step Using a 2 Phillips screwdriver remove the screw that holds in the Blank Head Phone Jack Cap at the lower front of the Hot Bar Retain the screw You will no longer need the cap and if desired you can store it away for any possible future use Now take the Head Phone Jack from the PVS CC hard ware kit Conect the Head Phone Jack to the c
34. the Personal Viewing Screen from the PVS kit Next take the 3 M8 Buttonhead screws the M8 Hex nut with washer and the 5mm Hex key from the PVS hardware tool kit STEP 6 Mount the Personal Viewing Screen on the Treadmill Using the 5mm hex key screw in the 2 M8 Buttonheads at the base of the PVS first do not tighten yet Using the 5mm hex key put one of the 8 Buttonhead screws into the hole on the PVS neck then put the hex nut with washer on the back side do not tighten STEP 7 Adjust the display cap up or down to align with the holes on the display front Once the cap is aligned tighten the buttonhead screws with the 5mm hex key STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE Align NR 9 19 STEP 8 Now that the 5 is mounted to the Treadmill you need to route the wires to their proper places 2 9 SA Center Console Take the coax cable O and feed it all the way down the treadmill neck Feed the DC power cable 2 from the treadmill ii neck through the center console hole Next take the Head Phone Jack cable 2 from the PVS neck connect it to the Head Phone Jack y fs Now feed the other 3 cables 4 through the dis Bottom View play and out the center console hole STEP 9 Take the Entertainment Center Console from the PVS Kit Cable Window Cen
35. uage English Basic Functions 24 STAR TRAC PERSONAL VIEWING SCREEN OWNER S MANUAL To navigate through the setup screens you will use the Entertainment Center Console keypad move between the items on the Main Menu press the i or To move to the items on the Sub Menu press the dun While in the sub menu use the 5 98 12 down to move bew teen items to select an item press the Use the and 9t UJ to modify the selected item as applicable then press the to return to the sub menu Use the 7 J to return to the Main Menu When you are finished modifying your Personal Viewing Screen settings press any number key in the Entertainment Center Console keypad to exit If no keys are pressed on the keypad for 30 seconds the setup screen will automati cally close You will need to press and 3 to enter back into the setup screens o CHANNEL MENU SETTING UP THE CHANNELS Tuning Band ern Cable Mode DTV Signal Auto CH Search VIDEO Manual CH Setting Channel label Options Menu Language English SETTING e Move Select 25 In the Channel Menu you will tell your system what type of signal it will be receiving Check with your provider to insure the best possible output In this menu you will also select what channels you would like your Personal Viewing Screen to show You will also select the Language that will appear in the Sub Menus
36. will see a printed headphone screw logo Use a 2 Phillips screwdriver to remove the screw holding the headphone jack in place Retain the screw for later use Gently pull the Headphone jack out of the display Be careful the headphone is connected to a cable Disconnect the cable Take the new Headphone jack and connect the cable Slide new Headphone jack into the Display plastic front using the screwdriver re install the screw This completes the Headphone replacement STAR TRAC PERSONAL VIEWING SCREEN OWNER S GUIDE Headphone Jack Screw eU 39 REGULATORY Radio Frequency Interference RFI Federal Communications Commission Part 15 Warning To prevent fire or electrical shock do not expose this equipment to rain moisture or excessive heat The unit has been tested and found to comply with the limits for Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equip ment is operated in a commercial environment The Personal Viewing Screen generates uses and can radiate radio frequency energy and if not installed and used in accordance with the assembly installation and maintenance instruction manu als may cause harmful interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipmen
37. will also explain how to replace the headphone jack when it no longer provides good audio quality Cleaning the Personal Viewing Screen Periodically dust the Personal Viewing Screen with a clean soft cloth For your Star Trac Cardio equipment refer to the owners manual for daily cleaning instructions and cautions information Caution DO NOT use liquid cleaners or aerosol cleaners to clean screen DO NOT use any solvents such as alcohol and paint thinner or any acidic cleaners to clean screen This will void the warrenty Each week or as needed clean the Center Console keypad with a mild soap and water solution Lightly dampen a clean cloth with the solution and wipe the keypad Do not use too much solution on the cloth or spray cleaning solution onto the center console Doing this could cause moisture to enter the controller and cause damage The following information may help you understand and troubleshoot any problems the you may encounter with your Star Trac Personal Viewing Screen If the suggestions in this table do not help solve the problem that you encounter please contact Star Trac s Service Hotline at 800 503 1221 or USA 1 714 669 1660 No Power Make sure that all the power cables are connected and secure Check that the plug is in a functional outlet Check the power supply at the base of the unit and see if the green LED is lit Push the Power button on the Center Console No Picture Make sure the PVS has power Make
Download Pdf Manuals
Related Search