Stanton SK 6F User's Manual
Contents
1. REPLACING INSTRUCTIONS 1 Remove the PROTEKT panel Cleaning instructions step 1 2 Remove the 2 outer screws from the toggle switch plate removing the 2 inner screws will detach the switch from the plate 3 Remove the switch assembly and disconnect the cable coming from the mixer 4 Set the replacement switch assem bly in the desired position and place the screws back in the top and bottom holes Line inputs 2 RCA 150 mV 27K ohm Phono inputs 2 RCA 3 47K ohm Send 2 1 4 150 mV 27K ohm Return 2 1 4 775 mV 1K ohm DJ mic input 1 1 4 inch 1 5 mV ohm 1 1 4 TRS Balanced RCA unbalanced 1 2 V 100 ohm 1 RCA 245 mV 100 ohm 1 1 4 inch 32 200 ohms recommended 20 Hz 20 KHz 2 dB 9 26 dB Hi Low 20dB 1 Khz Master output Record output Headphone output Frequency Response Tone Control Gain Control S N Ratio Less than 70dB T H D less than 0 2 Dimension LxWxD 12 3 8 x 10 1 4 x 4 314 x 260 x 102 mm Weight 7 lbs 3 2 Kg WARRANTY This unit has been designed and manufactured using quality components Therefore it is warranted to be free from defects in materials limited as specified below and workmanship for a period of twelve 12 months from the original pur chase date During this period all service and parts necessary to repair a defect will be free of charge This limited warranty applies to mechanical pa2. 2001 Stanton Magnetics LLC SK G6OF PROFESSIONAL MIXER is ee tren ses sats di 2 oats ne ia a pie ees ee en a ates ayes n tee el wa er ee SSE i Es Tey neers ef Oe eee u OWNER S MANUAL STANTON STANTON MAGNETICS LLC info stantonmagnetics com 954 929 8999 www stantonmagnetics com TROUBLESHOOTING Thank you for making Stanton your first choice in professional DJ mixers This innovative family of mixers has been developed with input from the professional DJ community bringing to the marketplace a previously unavailable affordable combination of user friendly functional design rugged construction and professional quality features Stanton and your authorized Stanton dealer are dedicated to your complete satisfaction by offering benchmark service and support throughout the long life of your Stanton product Again we appreciate your patronage and look forward to many years of making music together PLEASE READ CAREFULLY BEFORE USE FAILURE TO FOLLOW THE INSTRUCTIONS PRINTED BELOW MAY VOID WARRANTY e Follow all security advice printed on your mixer e When removing the unit s AC plug from the power source grasp and pull the plug NEVER the cord itself Avoid placing your mixer near heat sources such as power amplifiers e When in use place your mixer a stable surface away from vibration Always use
3. not on Faulty output connections Improper level adjustment Improper connection Improper level or cue mix settings SOLUTION Properly connect turntable ground wire to mixer ground terminal Properly ground the AC source Check all input and output connections for secure fit Isolate and replace damaged cable Connect amplifier or out board gear to master out put Properly connect AC cord to AC power source Turn power on Properly connect amplifier or outboard gear to mixer Properly set crossfader channel faders gain con trols and input selector tog gles Check headphone connec tion to mixer Tighten if nec Adjust headphone level and mix to the proper level and channel settings DESCRIPTION OF FUNCTIONS 1 Mic level Controls the overall microphone output level 2 Send Controls the level of the effect send output this is used to set the level of the signal going to the outboard effects processor or stomp box 3 Return Controls the level of the effect return input This is used to control the level of the processed signal going back into the mixer 4 FX Effect ON OFF for each channel MIC and cue 5 Gain Controls the input level of each chan nel 6 EQ Individual controls for low and high frequen cy equalization with 9 26 dB Note Any changes made to EQ set tings will change the over all output level 7 Master level C
4. TER position the pre selected signal of controls 13 and 17 will be monitored as a stereo signal in the headphones 19 Headphone outputs Connection for 1 4 and 3 5mm headphone jacks Recommended imped ance is 32 200 ohms for maximum volume 20 Crossfader Curve adjustment Adjusts the shape of the crossfader curve from a quick cut for scratching and cutting to a longer fade for mixing 21 Crossfader Reverse Reverses the direction of the crossfader 22 Power switch Selects power ON or OFF 23 Power supply con nector Input connection for the accompanying power supply 24 Master output TRS balanced 1 4 master out puts 25 Outputs Record out and unbalanced master RCA 26 Inputs Line and phono signal inputs for channels 1 and 2 27 Microphone input 1 4 connector 28 Ground posts Connect to the turntables ground connectors to eliminate electrical hum Ground connectors are usually supplied with turntables 29 Send amp return con nections The send out put is used to connect the mixer to the line input of your effects processor or sampler The return input is used to feed the signal back from the line output of the outboard unit This creates the effects loop 30 Program reverse Interchanges the outputs of channels 1 and 2 Notes on audio signal inputs outputs Line inputs are used to connect to line level sources such as CD play ers sample
5. care when carrying your mixer Impact or heavy vibration may compromise the unit s mechanical integrity The manufacturer is not responsible for damage resulting from an impact or misuse e When in use place your mixer away from sources of hum or noise such as transformers or electric motors To prevent overheating always provide your mixer with adequate ventilation air space e Avoid stepping on your mixer s cord Repeated compression of the cord may lead to electrical shorting To avoid damage due to AC voltage peaks always disconnect your mixer from the power source during electrical storms e Your mixer contains no user serviceable parts The manufacturer is responsible for any damage or personal injury resulting from unauthorized user servicing or modifications In addition the warranty will be void if any unauthorized service by the user is detected Always return your mixer to an authorized Stanton dealer for servicing PROBLEM Excessive hum when using phono source Low frequency hum while operating source unit Program volume can t be adjusted with master volume control No power The amplifier is turned up but there is no signal No signal in headphones CAUSE Poor ground connection Poor AC source ground Loose input output tion Shorted cable Amplifier or outboard gear connected to the record output Improperly connected AC cord or power line source
6. ontrols the overall signal output level 8 Headphone level Controls the overall head phone output level It is recommended head phones with an imped ance rating of 200 ohms or less be used for maxi mum volume 9 Cue pan Fades the headphone output between channels 1 and 2 effectively allowing the user to preview a mix 10 Power indicator Blue LED indicates whether mixer is ON or OFF 11 Input selector switches Selects phono or line inputs FLASH position allows users to quickly trigger the phono input 12 Input Fader Reverse Reverses the direction of each respective input channel fader Includes bi color LED to indicate the status of the reverse function When LED is green the fader is nor mal When LED is red the fader direction is reversed 13 Channel fader Controls the input chan nel level 14 Headphone mute Mutes the headphones without having to change its level 15 Input Level Meter Monitors each channel s input level with peak hold function 16 Crossfader Reverse LED Bi color LED indi cates the status of the crossfader reverse func tion When LED is green the crossfader is normal When LED is red the crossfader direction is reversed 17 Crossfader Fades the master output between channels 1 and 2 18 Cue select In CUE position the pre selected signal of control 9 will be monitored as a stereo sig nal in the headphones In MAS
7. rs tape play ers etc Phono inputs are used to connect to turntables Master output connects to an amplifier EQ crossover or other out board signal processing Record out connects to any line level recording device such as a tape deck DAT MD FADER CLEANING TECHNICAL SPECIFICATIONS The SK FOUR faders may need lubrication from time to time This will extend the fader life and eliminate any potential damage due to extended heavy usage Follow the instruction below the lubricate your faders 1 Remove the fader knobs and 4 screws located in the corners of the face plate and take the plate off the mixer 2 Remove the fader to be cleaned by unscrewing the 2 outer screws remov ing the 2 inner screws will detach the fader from the fader plate and discon nect the cable coming from the mixer 3 Spray a small amount of cleaner or lubricant into both ends of the fader and slide the fader back and forth a few times to spread the fluid evenly throughout the fader 4 Shake and wipe off excess fluid before re assembling the fader ROTATING AND REPLACING THE INPUT SWITCHES ROTATING INSTRUCTIONS 1 Remove the PROTEKT panel Cleaning instructions step 1 2 Remove the 2 outer screws from the toggle switch plate removing the 2 inner screws will detach the switch from the plate 3 Rotate the plate to the desired posi tion and tighten the screws back in the top and bottom holes
8. rts which are subject to wear and tear as specified Faders specified durability 15 000 cycles Rotary potentiometers specified durability 10 000 cycles Switches specified durability 10 000 cycles Consequently the parts listed above are warranted to be free from defects in materials and workmanship for a period of thirty days 30 days from the original purchase date R E P LAC E M NT PA RT S For the warranty to be valid please complete the warranty registration card To replace the cross or channel faders follow steps 1 and 2 of the cleaning instructions The following replacement parts are available from Stanton or your local Stanton dealer LF SK6 Channel fader CF SK6 Crossfader CFF1 Focus Fader PP SK6F Silver face plate PP SK6F B Blue face plate PL SK6 Two way input toggle switch 3PL SK6 Three way input toggle switch with FLASH PS 18US US Power Supply 110v PS 18EU European Power Supply 220v PS 18UK UK only Power Supply 240v attached or fill out the online registration at www stantonmagnetics com Mail completed warranty cards to Stanton Magnetics LLC 2821 Evans Street Hollywood FL 33020
Download Pdf Manuals
Related Search