Speco Technologies CVCM6DC User's Manual
Contents
1. may be replaced with or without the liner 3 If lighting is coming from behind the camera use the dome liner to hide the camera position 4 Before inserting the liner note the position of the camera lens so the lens will be placed at the opening of the liner when the dome is locked in 5 Align the dome cover tabs with the slots in the base gently press the cover into the slots and rotate clockwise until it is secure and the dome liner opening is aligned with the camera lens o speco technologies2. Mirror Finish Color Dome Camera CVCM6DC Specifications Image Sensor Number of Pixels Scanning System Horizontal Resolution Minimum Illumination Lens Signal to Noise Ratio Gain Control BLC Synchronization Electronic Shutter Gamma Correction White Balance Video Output Dimensions Voltage Requirement Current Draw Temperature Relative Humidity 1 3 Sony Super HAD CCD 510 H x 492 V NTSC 2 1 interlace 420 TV lines 0 2 lux 3 6mm gt 50dB Auto Auto Internal 1 60 1 100 000 sec 45 Auto 2500 9500 K 1V P P into 75Q 4 3 8 diameter x 3 5 8 high 12 10 VDC regulated 100 mA DC 14 F 122 F operating 22 F 158 F storage 0 95 o speco technologies Mirror Finish Color Dome Camera Wall or Ceiling Mount CVCM6DC Installation Instructions Always use discretion when installing video and or audio surveillance equipment especially when there is an expectation of privacy Inquire regarding federal state and or local regulations applicable to the lawful installation of video and or audio recording or surveillance equipment Party consent may be required 2 Ae 5 Z Z K AY ug Z j 4 Z z aU 4 y 4 A A H 7 aaa AF a p Z 4 g 3 5 4 7 A CIETIE IIIT PIIIITT Z A 7 o 77 4 CPI ite steel SAIELEEL EAPO This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful int
3. erference and 2 This device must accept any interference received including interference that may cause undesired operation Design and specifications are subject to change without notice Box Contents 1 CVCM6DC color camera 1 EZ mount base plate 1 Dome liner 3 Mounting screws with plastic anchors 1 Power supply pigtail 1 Installation guide 200 New Highway O Amityville NY 11701 1 800 645 5516 speco technologies www specotech com Mirror Finish Color Dome Camera CVCM6DC Installation Instructions Preparation Remove Dome Cover 1 Gently pull the inner liner away from the dome cover 2 Carefully turn the dome cover counterclockwise to unlock and pull it free from the housing then set both aside Camera Mounting Wall or Ceiling Mount 1 Remove EZ Mount Plate from i LLLLLL LALLA AAA L LL de bottom of camera by turning counterclockwise t 2 Determine if the connection wires Pa will exit from the bottom or side of se oe the base l 3 If wires are going through the side carefully remove the wire clearance tab on the side of the base 4 Mark holes for mount position as required 5 Attach plate to the mounting surface using anchors and screws supplied 6 Feed the connectors into the wire hole and align holes in camera base with EZ mount plate studs 7 Slip base over studs gently press base against the mounting surface and rotate until the base locks in place 8 If not us
4. ing EZ Mount Plate slip base over screws press base against the mounting surface and rotate until the base locks in place Tighten screws until base is firmly held but do not over tighten Note Depending on the material of your mounting surface you may require different screws and anchors than those supplied 05 30 08 Connections Note Observe Polarity This is a 12V DC camera to avoid damage please observe polarity Connect Wiring 1 Attach BNC connector from camera to a BNC male connector on your video cable 2 IF using a plug in power supply with attached connector verify that the center pin is the plus wire and the outer shell is the negative wire 3 IF extending power wire from a remote power supply verify polarity on feed from power supply Connect positive wire to red wire from pigtail supplied and attach negative wire to black wire from pigtail Verify that the center pin of pigtail connector is positive before connecting to the camera 4 Connect to power supply O Camera Adjustment Loosen screws on top amp sides to adjust rotation 3 Axis gimbal tilts up amp down 90 Loosen two side screws to adjust tilt angle Can be adjusted 360 Use these adjustments to align the camera position to obtain the image desired Replace Dome Cover 1 Use a soft lint free cloth to wipe the dome cover and remove finger prints 2 The dome cover
Download Pdf Manuals
Related Search