Spalding M662034 User's Manual
Contents
1. m cap 7 as shown Place assembled unit in desired location Fill tank completely with water 14 gallons 53 8 liters or sand approx 170 lb 77 kg and snap tank cap 9 in place ADD ONE GALLON 3 78 LITERS OF NON TOXIC ANTIFREEZE IN SUB FREEZING CLIMATES IF USING SAND 2 GALLONS OF ANTI FREEZE IS NOT REQUIRED ID M5800011 01 06 12 Install net 6 Attach height and moving label 23 to front of i pole as shown Regulation rim height is 10 feet READ AND UNDERSTAND FAILURE TO FOLLOW OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR DAMAGE TO PROPERTY R st unit on support table Remave adjustment knobs A and carriage bots B to extend or retract backboard and rim Height adjustment fom 4 1 2 6 1 2 AWARNING Backboard may rotate during height adjustment WARNING Do na adjust height of system Irupiht poston System must be in down positon to adjust 7 Read and understand warnings listed below before using this product Failure to follow these warnings may result in serious injury andlor property damage Owner must ensure that all players know and follow these rules for safe operation of the system DO NOT HANG on the rim or any part of the system including backboard support braces or net During play especially when performing dunk type activities keep player s face away from the backboard rim and net Ser2. 00 558 5234 In the U S 1 888 713 5488 In Canada 1 800 284 8339 ID 558200 05 05 A SAFETY INSTRUCTIONS A FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY Owner must ensure that all players know and follow these rules for safe operation of the system To ensure safety do not attempt to assemble this system without following the instructions carefully Proper and complete assembly use and supervision are essential for proper operation and to reduce the risk of accident or injury A high probability of serious injury exists if this system is not installed maintained and operated properly If using a ladder during assembly use extreme caution Check base regularly for leakage Slow leaks could cause the system to tip over unexpectedly Seat the pole sections properly if applicable Failure to do so could allow the pole sections to separate during play and or during transport of the system Climate corrosion or misuse could result in system failure If technical assistance is required contact Customer Service Minimum operational height is 4 6 1 37m to the bottom of backboard NOTICE TO ASSEMBLERS Adult Assembly Required Dispose of ALL packaging materials promptly As with all children s products periodically inspect for loose small parts Assembled unit MUST be filled with water at ALL times ALL basketball systems including those used for DISPLAYS MU
3. REQUIRED MATERIALS European Technical File A e Two 2 Capable De Ruyumbeke Adults 20 Bd Bourre NOT SUITABLE FOR CHILDREN 13008 Marseille France 88 378 UK 003 UNDER THREE YEARS OF AGE Tech File at DUE TO SMALL De Ruyumbeke e Wood Board PARTS CHOKING HAZARD France scrap e Sawhorse or This manual accompanied by sales receipt should be saved and kept on hand as a Support Table convenient reference as it contains important information about your model Garden Hose or Sand Portable System a wees Owners Manual and or Socket Wrenches and Sockets Customer Service Center N53 W24700 South Corporate Circle Sussex WI 53089 U S A 1 2 99 16 AND OR e Write Model Number 1 2 9 16 READ AND UNDERSTAND From Box Here OPERATOR S MANUAL BEFORE USING THIS UNIT OPTIONAL TOOLS FAILURE TO FOLLOW AND MATERIALS OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR DAMAGE TO PROPERTY Large and Small Adjustable Wrenches Toll Free Customer Service Number for U S 1 800 558 5234 For Canada 1 800 284 8339 For Europe 00 800 555 85234 Sweden 009 555 85234 For Australia 1 800 632 7921 Internet Address http www huffysports com COPYRIGHT 2005 by SPALDING 1 01 06 ID M5800011 HEIGHT ADJUSTMENT Rest unit on support table Remove adjustment knobs A and carriage bolts B to extend or retract backboard and rim Height adjustment from 4 1 2 6 172 Backboard
4. ST be assembled and ballasted with sand or water according to instructions Failure to follow instructions could result in SERIOUS INJURY It is NOT acceptable to devise a makeshift weight system IMPORTANT Remove all contents from boxes Be sure to check inside pole sections hardware and additional parts are packed inside Questions or Missing Parts DON T go hack to store ie ee to complete your product registration form either www huffysports com customer_support product_registration Call TOLL FREE Customer Service or mail in the enclosed postcard Number listed on the front page WARRANTY CARD 3 01 06 ID M5800011 ELEVATOR ASSEMBLY h LLLA E a I A AGSSG N 3 Q x S gt bh G 2 Q Q Y Q x o O MIDDLE POLE ID M5800011 01 06 Silver W Item Qty OO NDMNO RPM PE El VISE EES SE EEE a EEE eye ei 1 1 1 1 1 1 1 3 1 1 2 1 1 1 1 2 4 1 1 3 1 1 1 Part No 20664903 918130 918133 918132 203099 20378701 203223 203617 203740 201344 908134 908129 203739 203218 203309 203679 203100 910454 910255 558170 PARTS LIST Description Tank Black Top Pole Section Middle Pole Section with Label Bottom Pole Section Nut Ny Lock 5 16 18 Net Cap Pole Bolt Carriage 5 16 18 x 1 Long Cap Tank Bolt Hex 5 16 18 x 2 63 Long Kn
5. anism from shifting Keep pole top covered with cap at all times Do not allow water in tank to freeze During sub freezing weather add 2 gallons of non toxic antifreeze sand or empty tank completely and store Do not use salt While moving system do not allow anyone to stand or sit on base or have added ballasting on base Do not leave system unsupervised or play on system when wheels are engaged for moving Use Caution when moving system across uneven surfaces System may tip over Use extreme caution if placing system on sloped surface System may tip over more easily See instruction manual for proper installation and maintenance HYDRA RIB RUSSELL ATHLETIC 13 01 06 ID M5800011
6. ation Check pole system for signs of corrosion rust pitting chipping and repaint with exterior enamel paint If rust has penetrated through the steel anywhere replace pole immediately Check system before each use for proper ballast loose hardware excessive wear and signs of corrosion and repair before use Check system before each use for instability Do not use system during windy and or severe weather conditions system may tip over Place system in the storage position and or in an area protected from the wind and free from personal property and or overhead wires Never play on damaged equipment When moving system use caution to keep mechanism from shifting Keep pole top covered with cap at all times Do not allow water in tank to freeze During sub freezing weather add 2 gallons of non toxic antifreeze sand or empty tank completely and store Do not use salt While moving system do not allow anyone to stand or sit on base or have added ballasting on base Do not leave system unsupervised or play on system when wheels are engaged for moving Use Caution when moving system across uneven surfaces System may tip over Use extreme caution if placing system on sloped surface System may tip over more easily See instruction manual for proper installation and maintenance ALDING HYDRA RIB In the U S 1 800 334 9111 Inthe U S 1 800 558 5234 a ee RUSSELL BATHLETIC HUFFY SPORTS In the U S 1 8
7. ious injury could occur if teeth face come in contact with backboard rim or net Do not slide climb shake or play on base and or pole After assembly is complete fil system completely with water or sand Never leave system in an upright position without filing base with weight as system may tip over causing injuries When adjusting height or moving system keep hands and fingers away from moving parts Do not allow children to move or adjust system During play do not wear jewelry rings watches necklaces etc Objects may entangle in net Surface beneath the base must be smooth and free of gravel or other sharp objects Punctures cause leakage and could cause system to tip over Keep organic material away from pole base Grass litter etc could cause corrosion and or deterioration Check pole system for signs of corrosion rust pitting chipping and repaint with exterior enamel paint If rust has penetrated through the steel anywhere replace pole immediately Check system before each use for proper ballast loose hardware excessive wear and signs of corrosion and repair before use Check system before each use for instability Do not use system during windy and or severe weather conditions system may tip over Place system in the storage position and or in an area protected from the wind and free from personal property and or overhead wires Never play on damaged equipment When moving system use caution to keep mech
8. may rotate during height adjustment AWARNING Do not adjust height of system in upright position System must be in down position to adjust 558170 07 05 ID M5800011 01 06 Read and understand warnings listed below before using this product Failure to follow these warnings may result in serious injury and or property damage Owner must ensure that all players know and follow these rules for safe operation of the system DO NOT HANG on the rim or any part of the system including backboard support braces or net During play especially when performing dunk type activities keep player s face away from the backboard rim and net Serious injury could occur if teeth face come in contact with backboard rim or net Do not slide climb shake or play on base and or pole After assembly is complete fill system completely with water or sand Never leave system in an upright position without filling base with weight as system may tip over causing injuries When adjusting height or moving system keep hands and fingers away from moving parts Do not allow children to move or adjust system During play do not wear jewelry rings watches necklaces etc Objects may entangle in net Surface beneath the base must be smooth and free of gravel or other sharp objects Punctures cause leakage and could cause system to tip over Keep organic material away from pole base Grass litter etc could cause corrosion and or deterior
9. ob Plastic 3 sided Rim Backboard Backboard Mounting Bracket Rim Bracket Bolt Carriage 5 16 18 x 3 25 Long Washer Flat 5 16 Washer Flat 1 0 O D Bolt Hex 3 8 16 x 2 Long Nut Flange 5 16 18 Strut Left Strut Right Label Height Adjustment You may have extra parts with this model 01 06 ID M5800011 PARTS IDENTIFIER Actual Size mm eg 5 1 17 4 ANN Y 20 3 PA we a 21 1 22 1 13 1 ID M5800011 01 06 6 SECTION A ASSEMBLE THE POLES 1 Correctly identify each pole section Poles have an identification sticker a that will be used as a reference point in the next step Reference Stickers BOTTOM 7 01 06 ID M5800011 IMPORTANT ONCE POLE SECTIONS ARE POUNDED TOGETHER THEY CANNOT BE TAKEN APART middle poles together by bouncing them on a scrap piece of e slionment m rk a wood on the ground as shown in FIG A until they no longer g move toward pole identification stickers THEN add bottom pole section and pound together in the same way 2 Align poles using alignment marks First pound top and THE IDENTIFICATION STICKER IS LOCATED 3 3 4 FROM THE END OF THE POLE WHEN PROPERLY POUNDED TOGETHER THE POLE SECTIONS SHOULD HAVE A 2 1 2 MINIMUM OVERLAP LEAVING 1 1 4 BETWEEN THE OVERLAPPING POLE AND THE IDENTIFICATION STICKER alignment mark MIDDLE IDENTIFICATION STICKER scra
10. p wood Not Supplied 7 alignment mark BOTTOM IDENTIFICATION f ICKER ID M5800011 01 06 8 Attach pole assembly to tank as shown Secure pole assembly to tank by turning the pole assembly clockwise as shown CAREFULLY TIPPING THE SYSTEM FORWARD WILL ALLOW EASIER ACCESS TO UNDERSIDE OF BASE TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND OR PROPERTY DAMAGE 9 01 06 ID M5800011 4 Secure tank struts 21 amp 22 to pole E TIGHTEN BOLT 10 IN LOCK NUT 5 UNTIL FLUSH EVEN WITH LOCK NUT S OUTER EDGE FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND OR PROPERTY DAMAGE Rotate struts down and bend struts outward to line up with holes on base as shown Secure free ends of tank struts to tank with carriage bolt 8 and nut 20 as shown Repeat for other side ID M5800011 01 06 completely into place Attach rim to backboard and pole bracket 14 with nut 20 Pole bracket will need to be lightly pressed into backboard ribbing Be sure to press 6 a reinforcement bracket 15 and carriage bolt 8 as shown Tighten nut completely PRESS BRACKET 14 INTO PLACE Carefully tip unit forward and slide backboard assembly onto pole as shown SAWHORSE OR SUPPORT TABLE 11 01 06 ID M5800011 Attach board assembly to pole with carriage bolts 16 and knobs 11 as shown Install pole
Download Pdf Manuals
Related Search