Spalding 211376A User's Manual
Contents
1. aa 11 05 03 P N211376A REAR VIEW OF Y FRAME 27 Looselv assemble bolt 28 and nut 29 to Y frame support bracket 27 as shown Repeat for opposite side NOTE Bolt 28 heads face outward toward backboard 2 NOTE Two people recommended for this operation Attach Y frame support bracket 27 to elevator tubes 15 as shown IMPORTANT NOTE DO NOT OVER Same hardware TIGHTEN used for upper and lower installation PIN 211376A 05 03 12 til a3 Lift backboard upright and insert bolt 28 heads into kev slots Slide backboard downward to position bolt 28 into channel as shown Align rim mounting holes on Y frame support bracket 27 to rim holes on backboard and tighten completely AWARNING TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY IMPORTANT ALIGN RIM MOUNTING HOLES WITH HOLES IN Y FRAME 13 05 03 P N 211376A Install net clips 34 The Quick Clip rapid release net system lets the net pull away from the rim This reduces the risk of player injury or property damage However improper installation or a ball making contact at an odd angle may disengage the net clip from the goal rim Usually the clip is reinstalled with little or no problem We hope that you agree this inconvenience is minor when compared to the safety of the players Quick Clip US Patent No 5 792 010 5 795 253 OUTSIDE VIEW Attach rim 332. The two outer hooks on net clip must face towards inside of goal rim Insert larger hole in net clip onto rim stud push down on net clip then slide net clip right locking or snapping securely into position clips must snap into place to insure a secure fit NOTE Net clips should not slide with ease It is very important that the net clips are in the locked position before going on to next step Note Mounting nuts 29 and bolts 31 supplied with rim hardware Refer To Instructions Included With Rim Hardware For Rim Assembly P N 211376A 05 03 14 OUTER HOOKS AWARNING USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF NET CLIPS OR WHEN ALL NET CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM BE SURE TO FOLLOW DIRECTIONS CAREFULLY Install net 35 A Slide net into outer hook as shown B Slide net into second outer hook creating a loop as shown Push loop to back of clip C Pull loop up and through back of clip snapping over the middle hook D Pull net down to make sure it is held securely by all three hooks NOTE If net releases during normal play net was improperly installed Please review instructions to install net properly FRONT VIEW BACK VIEW IMPORTANT MAKE SURE NET IS HELD BY ALL THREE HOOKS ON THE NET CLIP Position looped end of height adjustment crank 36 onto hook as shown Rotate crank handle to raise or lower backboard View label 20
3. 12 onto bottom section 3 Bend back exposed top flange sections of secured ground sleeve 4 as shown Then insert pole into ground sleeve 4 Secure clamps 7 around pole section as shown Refer to Step 4 Tighten completely 15 Beginning with top hole in left and right screw jack support plates 16 amp 17 install elevator tubes 15 to pole as shown Then secure lower holes in support plates to pole NOTE Not all holes in support plates 16 amp 17 are used in this assembly IMPORTANT DO NOT OVER TIGHTEN i 9 05 03 P N 211376A Attach height decal 20 on screw jack 21 Align lower edge of decal 20 with bottom of black indicator tube SCREW JACK BOTTOM Center screw jack 21 between support plates 16 8 17 and secure as shown below Attach logo label 22 to height indicator cover 23 Place cover 23 over screw jack 21 Install pole cap 11 IMPORTANTI DO NOT OVER TIGHTEN P N 211376A 05 03 10 a Secure upper elevator tubes 15 to pole assembiv as shown IMPORTANTI DO NOT OVER TIGHTEN Insert spacer 25 through top holes of height indicator cover 23 and screw jack assembiv as shown Align spacer 25 and screw jack assembly between elevator tubes 15 and secure IMPORTANT WHEN SECURING SCREW SCREW JACK JACK 21 TO TOP ASSEMBLY ELEVATOR TUBES 15 USE SPACER 25 BETWEEN ELEVATOR TUBES AS SHOWN
4. 4 Thick 906266 Y Frame Support Bracket 206263 Bolt Carriage 5 16 18 x 3 Long 203100 Nut Flange 5 16 x 18 206261 Bolt Hex Head 1 2 13 x 3 Long 202662 Bolt Hex Flange 5 16 18 x 4 1 2 808804 Pole Pad Rim 200121 Clip Net Holder Black 200120 Clip Net Holder Red 204282 Net 806259 Crank Height Adjustment 201248 Label Height Adjustment OO JO Om P GO a ch hb sch MAM sch KH BRON AN HAND AH sch ch a P DW NANNAN sch ch AH sicht it CH YOU MAY HAVE EXTRA PARTS WITH THIS MODEL HARDWARE IDENTIFIER GCN SY mm jee O Item 10 2 Item 5 2 Item 6 4 Item 8 2 2 Item 14 167 jan E Item 18 10 Item 19 1 Item 13 3 HARDWARE IDENTIFIER CONTINUED a 17 05 03 P N211376A HARDWARE IDENTIFIER CONTINUED mm L JO Item 24 2 Item 25 1 0 ommna Item 28 2 Item 29 6 Item 26 2 T m Jo Item 34 127 Item 30 4 fs Item 31 4 YOU MAY HAVE EXTRA PARTS WITH THIS MODEL P N 211376A 05 03 18
5. Customer Service e N53 W24700 South Corporate Circle Sussex WI 53089 U S A A Huffv Companv WRITE IN VOUR MODEL NUMBER In Ground Basketball Svstem Owner s Manual A SAFETY INSTRUCTIONS A FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY PROPERTY DAMAGE AND WILL VOID WARRANTY Owner must ensure that all players know and follow these rules for safe operation of the system To ensure safety do not attempt to assemble this system without following the instructions carefully Proper and complete assembly use and supervision is essential for proper operation and to reduce the risk of accident or injury A high probability of serious injury exists if this system is not installed maintained and operated properly Check entire box and inside all packing material for parts and or additional instructional material Before beginning assembly read the instructions and identi arts using the hardware identifier and parts list in this document If using a ladder during assembly use extreme caution Two 2 people are recommended for this operation Seat the pole sections properly Failure to do so could allow the pole sections to separate during play Before digging contact utility company to locate underground power cables gas and water lines Ensure there are no overhead power lines within 20 ft 7 m radius of pole location Climate corrosion excessive use or misuse could result in system failure If te
6. chnical assistance is required contact Huffy Sports Minimum operational date is 6 6 1 98 m ni seat of backboard REQUIRED TOOLS AND This equipment is intended for home recreational use only and NOT MATERIALS excessive competitive play Read and understand the warning label affixed to pole Label is shown on page 6 The life of your basketball pole depends on many conditions The climate placement of the pole the location of the pole exposure to corrosives such as Tape pesticides herbicides or salts are all important Shovel and Spade Adult supervision is recommended when adjusting height Concrete 900 Ib 408 kg and Container to Mix Serious injury could occur if teeth face come in contact with backboard net or rim Two People Tape Measure Carpenter s Level Wood Board Scrap Most injuries are caused by misuse and or not following instructions Step Ladder 8 ft 2 4 m Use caution when using this system Wrenches Two 1 2 9 16 3 4 or two Large and B 7 W Small Adjustable Wrenches For more information on assembiv placement proper use and maintenance visit The American Basketball Council website at http www smarthoops com Drill Safetv Goggles In U S and Canada oniv Have questions don t go back to the storel We appreciate vour purchasing one of our manv fine products We are sure that vou will be verv satisfied with vour selection Although great care and effort have been taken occasionally prob
7. in contact with backboard rim or net Do not slide climb shake or play on pole When adjusting height keep hands and fingers away from 201248 2 99 moving parts Do not allow children to move or adjust system During play do not wear jewelry rings watches necklaces etc Objects may entangle in net Keep organic material away from pole base Grass litter etc could cause corrosion and or deterioration Check pole system for signs of corrosion rust pitting chipping and repaint with exterior enamel paint If rust has penetrated through the steel anywhere replace the pole immediately Check system before each use for proper ballast loose hardware excessive wear and signs of corrosion and repair before use Check system before each use for instability Never play on damaged equipment Keep pole top covered with cap at all times See instruction manual for proper installation HUFFY SPORTS In the U S 1 800 558 5234 and Canada 1 800 284 8339 201240 2 99 05 03 P N 211376A IMPORTANT WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL G Questions or Missing Parts DON T go back to store Call TOLL FREE Customer Service Number listed on the front page Correctly identify each pole section and mark indicated distance from ends with tape 5 1 2 14 cm TOP MIDDLE NOTE Maximum distance Make sure ground is level with from edge of hole to edge of pla
8. lems may occur To ensure prompt and correct handling of any problems or to answer any questions please contact our Toll Free Customer Service Number listed below Service will be quicker if you have your Model Number found on carton and assembly instructions ready when calling PLEASE WRITE YOUR MODEL NUMBER IN THE SPACE PROVIDED ABOVE Toll Free Customer Service Number for U S 1 800 558 5234 For Canada 1 800 284 8339 For Europe 00 800 555 85234 Sweden 009 555 85234 For Australia 1 800 333 061 Internet Address http www huffvsports com COPYRIGHT 2001 by HUFFY SPORTS 1 taa printed on recvcled paper 05 03 P N 211376A BEFORE VOU STARTI To ensure optimal plavabilitv of backboard svstem a close tolerance fit between the elevator components and hardware is required Test fit large bolts into large holes of elevator tubes backboard brackets and triangle plates Carefully rock them in a circular motion to ream out any excess paint from holes if necessary AVANT DE COMMENCER Pour garantir l utilisation optimale du panneau les composants du syst me l vateur et la visserie doivent tre bien ajust s serr s titre d essai ins rez les gros boulons dans les gros trous des tubes du syst me l vateur des supports du panneau et des plaques triangulaires Basculez les avec pr caution en imprimant un mouvement circulaire pour liminer l exc dent de peinture si n cessaire ANTES DE COMENZAR Para asegu
9. ons should have a 4 1 2 11 4 cm minimum overlap IMPORTANTI Add bottom pole section 3 to assembiv Bounce pole sections together 3 times rotate 90 and repeat rotation bounce procedure Continue this step until pole sections are completelv tight NOTE Pole sections should have a 4 1 2 11 4 cm minimum overlap Drill a hole in the backside of each of the two pole sections joint areas 1 2 54 cm above bottom of poles and install screws 10 as shown NOTE Drill bit 9 provided WOOD SCRAP Insert pole cap 11 onto end of bottom pole 3 Mix concrete approximatelv 100 Ibs 45 4 kg and fill pole 1 2 2 54 5 0 cm below bottom elevator hole on top pole section 1 as shown IMPORTANTI TWO PERSON MINIMUM WAIT MINIMUM OF REQUIRED FOR THIS 24 HOURS BEFORE PROCEDURE GOING ON TONEXT NOT FOLLOWING STEP CONCRETE RECOMMENDATION MAV MUST CURE RESULT IN BODILY INJURY IMPORTANT FAILURE TO FILL YOUR POLE COMPLETELY WITH CONCRETE AS DESCRIBED IN THESE INSTRUCTIONS WILL VOID ALL WARRANTIES WRITTEN OR IMPLIED A 7 05 03 P N211376A IMPORTANTI ELEVATOR HOLES MUST BE PARALLEL WITH PLAVING SURFACE PLAVING SURFACE Lower clamp cover 12 over clamps and snap into proper position P N 211376A 05 03 AWARNING TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY Remove pole cap 11 from bottom pole section and insert clamp cover
10. rar el ptimo rendimiento del sistema del respaldo en el juego se requiere un ajuste de tolerancia estrecha entre los componentes del elevador y el herraje Pruebe el ajuste de los pernos grandes en los orificios grandes de los tubos elevadores soportes del respaldo y placas triangulares Cuidadosamente mu valos en c rculos para eliminar cualquier exceso de pintura si es necesario VORBEREITENDE MASSNAHMEN Um sicherzustellen dass das Korbwandsystem optimal f r den Spielbetrieb geeignet ist m ssen die Komponenten der Verlangerungsvorrichtung und die verschiedenen Befestigungsteile fest miteinander verschraubt werden Grofe Schrauben zur Probe in die groBen L cher der Verl ngerungsrohre Korowandklammern und Dreiecksplatte stecken und diese vorsichtig in einer Kreisbewegung hin und herbewegen um eventuelle Farbr ckst nde aus den Bohrungen zu entfernen P N 211376A 05 03 2 al FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND OR PROPERTY DAMAGE TO ADJUST BACKBOARD Owner must ensure that all players know and follow these rules for safe operation of the system Position looped end of crank onto hook as shown DO NOT HANG on the rim or any part of the system Rotate crank handle to including backboard support braces or net raise or lower backboard During play especially when performing dunk type activities keep player s face away from the backboard rim and net Serious injury could occur if teeth face come
11. to determine approximate backboard height NOTE If height adjustment is difficult to operate you may have over tightened the areas indicated Refer to Steps 15 19 20 and 22 AWARNING STORE CRANK OUT OF REACH OF CHILDREN DO NOT ALLOW CHILDREN TO ADJUST HEIGHT WITHOUT ADULT SUPERVISION COULD RESULT IN SERIOUS BODILY HARM AND OR PROPERTY DAMAGE a 15 05 03 P N211376A Apply height adjustment label 37 to front of pole as shown 10 feet 3 05 m REGULATION RIM HEIGHT IS 10 FEET 3 05 M Secure pole pad 32 as shown P N 211376A 05 03 16 ta PARTS LIST Item Qty PartNo Description Item Qty PartNo Description 900757 Top Pole Section 900874 Middle Pole Section Flared End 908215 Bottom Pole Section 206500 Ground Sleeve Square 201124 Lock Nut Hex Head 3 8 x 16 203232 Washer Flat 3 8 x 3 4 O D 206512 Clamp V shaped 206252 Bolt Hex Head 3 8 16 x 1 Long 202872 Drill Bit 3 16 202871 Screw Tap 1 4 x 3 4 206899 Pole Cap Square 206502 Clamp Cover 201640 Bolt Hex Head 1 2 13 x 7 1 4 Long 203474 Washer 1 2 I D 900883 Elevator Tube 906277 Jack Support Plate Left 906276 Jack Support Plate Right 201646 Lock Nut Hex 1 2 13 206262 Bolt Hex Head 1 2 13 x 5 Long 211236 Decal Height Indicator 805231 Screw Jack 202795 NBA Logo Label 206234 Cover Height Indicator 206272 Bolt Hex Head 1 2 13 x 1 206275 Spacer 3 4 O D x 4 9 16 201651 Spacer Plastic 1
12. ying surface then dig pole hole playing surface 6 15 2 cm A WARNING CONTACT UTILITIES BEFORE DIGGING PLAYING SURFACE 6 B m GROUND SURFACE P N 211376A 05 03 G Insert bottom pole section 3 into ground sleeve 4 Assemble clamps 7 around bottom pole and ground sleeve 4 as shown Fill hole approximately 3 4 full with concrete Tamp down concrete to release air pockets PLAYING SURFACE IMPORTANT CLAMP ASSEMBLY MUST BE POSITIONED AS SHOWN BELOW A 5 05 03 P N211376A Insert ground sleeve 4 and pole section 3 into hole Fill remaining hole with concrete Tamp down concrete to release air pockets and build drainage hill Center and level ground sleeve assembiv in hole Check leveling on all sides several times while concrete is curing NOTE Make sure concrete is set up to clamp assembly as shown below IMPORTANT FRONT OF POLE MUST BE PARALLEL WITH PLAYING SURFACE PLAYING SURFACE PLAYING SURFACE After concrete cures remove clamp assembly and lift bottom pole section 3 from ground sleeve 4 as shown FILL TO HERE SIS 0 0 4 lo J l ALS E LE IMPORTANTI WAIT MINIMUM OF 24 HOURS BEFORE GOING ON TO NEXT STEP CONCRETE MUST CURE PIN 211376A 05 03 6 ai IMPORTANTI Bounce pole top 1 and middle section 2 together as shown until thev no longer move toward taped reference mark NOTE Pole secti
Download Pdf Manuals
Related Search