Sony UWP-C1/C2 User's Manual
Contents
1. 29 Detecting and selecting the available channels automatically diversity tuner module URX M1 only 30 Setting the attenuation level of the audio input 31 Resetting the accumulated battery use time indication 32 Setting the RF output level 32 Setting the monitor level portable diversity tuner URX PI only 33 Operation 211 211 1 n2 1 34 System Configurations 35 Error Messages 1 38 Troubleshooting 39 Specifications 11 11111112 41 Appendix 2222 122 s n1n0011 45 Wireless microphone system frequency ist 121121112112 45 AC adapter for use with the URZERT yy NIE 47 Configuration of the Packages UWP C1 This operation manual is for the UWP C1 C2 S 1 S2 X1 X2 wireless microphone packages The contents of each package are described below The UWP C1 consists of a body pack transmitter UTX B1 and a portable diversity tuner URX P1 When used in conjunction with a compact camcorder the UWP C1 makes a mobile system for ENG Electronic News Gathering or EFP Electronic Field Production purposes Body pack transmitter Portable diversity tuner UTX B1 1 URX P1 1 Supplied accessories e Omni directional lavalier microphone Wind screen 1 Holder clip 1 1 Q XLR BMP conversion cable for us2. 2 Press the SET button repeatedly until the accumulated time indication appears in the display section GC dt Sit i tnie 32 3 Press the button The time indication resets to 00 00 While 00 00 is still displayed you can return to previous value by pressing the button 4 a For transmitters UTX B1 H1 Set the POWER switch to OFF to complete the setting or press the SET button to set other items The results are stored in memory The change becomes effective the next time you turn on the unit by setting the POWER switch to ON 4 bFor the portable diversity tuner URX P1 Leave the tuner for about 10 seconds until the time indication stops flashing and the setting is stored in memory Setting the RF output level The procedure below is the same for all UWP series transmitters UTX B1 H1 You can select an RF output level of H 10 mW or L 2 mW in setting mode Set the RF output level to L 2 mW for simultaneous operation of multiple channels and set it to H 10 mW for long distance operation 1 Turn on the transmitter while pressing down the SET button 2 Press the SET button repeatedly 2 Press the button to increase the until the RF output level monitor level or press the indication appears in the display button to decrease the level section When you leave the tuner for MM k i I 7 about two seconds or more hr ae current monitor level settin
3. O N Y 2 347 711 32 2 Wireless Microphone Package Operating Instructions Before operating the unit please read this manual thoroughly and retain it for future reference UWP C1 C2 UWP S1 S2 UWP X1 X2 2003 Sony Corporation Table of Contents Configuration of the Packages 11 111111111111111111 4 UWP Cl wozi tei ete 4 UWP CZ az sad 5 UW P S let soi czy 6 UWBZSZ a i nats 7 UWP X I eiieeii tsis 8 UWPZX2 aenn 9 Features sesssessseeunsenunsennennnsennne 10 Precautions 111 2 111 1211112 12 Parts Identification 13 Body pack transmitter UTXEBT dzi 13 Hand held microphone UTX HI za ic zada 14 Portable diversity tuner URZEPO Jedni a 15 Half rack size diversity tuner URZERT wench ada dA 17 Diversity tuner module URX MI 4 4224211212 1 18 Power Supply 12 1111 21 1 20 Inserting the batteries 20 Attachment and Installation Procedures 1 111112 23 Attaching the supplied accessories to the body pack transmitter UTX B1 23 Attaching the supplied accessory to the hand held microphone UTXEHL eieae nmaa 24 Attaching the supplied accessories to the portable diversity tuner CURX PY aaa zo cee 24 Installing the diversity tuner module URX M1 25 Settings 1 2 12221110 n111 12 1 28 Setting the transmission Channels wes ind 28 Setting the reception channel
4. 13 795 625 68 19 796 375 68 17 796 125 68 25 797 125 68 22 796 750 68 30 797 750 68 28 797 500 68 34 798 250 68 36 798 500 68 37 798 625 68 38 798 750 Group H1 Group H2 Grouping 7 channels Grouping 7 channels CH MHz CH MHz 69 09 801 125 69 10 801 250 69 11 801 375 69 13 801 625 69 19 802 375 69 17 802 125 69 25 803 125 69 22 802 750 69 30 803 750 69 28 803 500 69 34 804 250 69 36 804 500 69 37 804 625 69 38 804 750 46 AC adapter for use with the URX R1 Please prepare an AC adapter which satisfies the following conditions for normal operation of the URX R1 Half rack Size Diversity Tuner e Specifications AC input voltage Differs according to the countries DC output voltage 9 0 V DC Rated load current more than 300 mA DC e The size of the DC output connector DC jack see O 47 Sony Corporation Printed in Korea http www sony net
5. F Details on inserting the batteries and the battery condition indication are given below 20 Inserting the batteries Body pack transmitter UTX B1 portable diversity tuner URX P1 The procedure below uses the body pack transmitter UTX B1 in the illustrations Batteries are however inserted in the portable diversity tuner URX P1 in the same manner 1 Slide the latches on both sides of the transmitter tuner at the same time and open the battery compartment 2 Align two new LR6 size AA alkaline batteries with the polarity markings and insert them into the battery compartment and then close the cover Hand held microphone UTX H1 1 Turn the grip in the direction of the arrow to open the battery compartment 3 Turn the grip in the direction opposite to the arrow in step 1 to close the battery compartment 2 Align two new LR6 size AA ESA i If you open the battery compartment alkaline batteries with the polarity RAE during signal transmission the noise markings and insert them into the B h battery conan may occur Be sure to turn the y P microphone off before opening the battery compartment Battery indication When you turn the power on the battery condition is shown by the BATT indication in the display section When the indication in column 4 starts to flash replace the batteries with new ones Be sure to check the
6. install or uninstall the diversity tuner module URX M1 while the unit is turned on as this may damage the connector or cause noise 25 Attachment and Installation Procedures ESS ee ZOE AZER T e The buttons and display on the front panel of the diversity tuner module URX M1 may be damaged if they are gripped too strongly Always hold the diversity tuner module by the side e Do not put your fingers on the connectors on the rear panel of the diversity tuner module URX M1 or into the slot on the unit into which the diversity tuner module URX MI will be installed e Keep the diversity tuner module URX M1 away from static electricity Installing a diversity tuner module URX M1 into an MB 806A Tuner Base Unit The MB 806A Tuner Base Unit can accommodate up to 6 diversity tuner modules URX M1 1 Holding both sides of the diversity tuner module URX M1 insert it into the slot Push it in until you hear a click 26 2 To install two or more diversity tuner modules URX M1 detach the necessary number of blank panels by pressing the top and bottom tabs on each panel towards each other and pulling the panel out Then do step 1 for each module Removing a diversity tuner module URX M1 On the bottom panel of the MB 806A locate the lever corresponding to the slot of the diversity tuner module URX M1 to be removed and pull the lever forward The diversity tuner module URX M1 is eject
7. the connector cover Nate The supplied conversion cables are for use with the URX PI only Attaching the cable to the audio input connector of the UTX B1 may cause damage to the transmitter or the device connected to the transmitter Attaching the belt clip See Attaching the belt clip on page 23 Attaching the shoe mount adapter Attaching the microphone stand adapter Be sure to hold the horizontal part of the belt clip with the horizontal groove on the shoe mount adapter After attaching the belt clip insert the shoe mount adapter between the portable diversity tuner URX P1 and the belt clip with the vertical parts of the belt clip aligned with the two vertical parallel grooves on the shoe mount adapter Then push the shoe mount adapter in the direction of the arrow and then catch the horizontal part of the belt clip with the horizontal groove on the shoe mount adapter to hold the belt clip in place After attaching the belt clip and the shoe mount adapter insert the microphone stand adapter into the screw hole at the top of the shoe mount adapter and then rotate the microphone stand adapter until it is securely attached Installing the diversity tuner module URX M1 e Before installing the diversity tuner module URX M1 make sure the unit into which the diversity tuner module URX MI will be installed is turned off Do not
8. to the body pack transmitter UTX B1 Attaching the microphone Microphone supplied For a secure connection be sure to turn and lock the connector cover Attaching the holder clip to the microphone Push the holder clip against the bottom of the microphone until the holder clip clicks into place Attaching the wind screen to the microphone Z Insert the microphone into the hole at the bottom of the windscreen Attaching the belt clip A Insert one end of the belt clip into one of two holes on either side of the transmitter and then insert the other end into the hole on the other side 23 Attachment and Installation Procedures Sa ee Z T Removing the belt clip Insert a pointed object such as a ballpoint pen between the belt clip and the transmitter to make some space between them and then remove the end of the belt clip from the hole on the side of the transmitter Attaching the supplied accessory to the hand held microphone UTX H1 Attaching the microphone holder Insert the bottom part of the microphone into the holder 24 Attaching the supplied accessories to the portable diversity tuner URX P1 Connecting the supplied conversion cable to the OUTPUT connector Example XLR BMP conversion cable supplied For a secure connection be sure to turn and lock
9. 44 805 500 68 21 796 625 68 45 799 625 69 21 802 625 69 45 805 625 68 22 796 750 68 46 799 750 69 22 802 750 69 46 805 750 68 23 796 875 68 47 799 875 69 23 802 875 69 47 805 875 68 24 797 000 69 24 803 000 45 Appendix Groups for tuner Group 11 Group 12 Group 13 Grouping 11 channels Grouping 8 channels Grouping 8 channels CH MHz CH MHz CH MHz 68 05 794 625 69 01 800 125 68 03 794 375 68 14 795 750 69 05 800 625 68 13 795 625 68 25 797 125 69 11 801 375 68 18 796 250 68 41 799 125 69 25 803 125 68 26 797 250 68 47 799 875 69 28 803 500 68 37 798 625 69 12 801 500 69 36 804 500 68 40 799 000 69 16 802 000 69 41 805 125 68 44 799 500 69 30 803 750 69 43 805 375 68 46 799 750 69 37 804 625 69 40 805 000 69 42 805 250 Group A1 Group A2 Group A3 Grouping 8 channels Grouping 7 channels Grouping 7 channels CH MHz CH MHz CH MHz 68 06 794 750 69 11 801 375 68 10 795 250 68 20 796 500 69 22 802 750 68 21 796 625 68 24 797 000 69 30 803 750 68 29 797 625 68 40 799 000 69 36 804 500 68 35 798 375 69 04 800 500 69 40 805 000 68 39 798 875 69 17 802 125 69 43 805 375 68 42 799 250 69 23 802 875 69 45 805 625 68 44 799 500 69 47 805 875 Group L1 Group L2 Grouping 7 channels Grouping 7 channels CH MHz CH MHz 68 09 795 125 68 10 795 250 68 11 795 375 68
10. 45 Pressing the button cycles the indications in the opposite direction Hold down the or button to change the channel number or frequency faster 28 4 When the desired channel number or frequency appears set the POWER switch to OFF to complete the setting or press the SET button to set other items The results are stored in memory The stored channel number or frequency will appear in the display section the next time you turn on the transmitter by setting the POWER switch to ON e When you are setting the transmission channel the transmitter cannot be used to transmit signals e Do not remove the batteries while setting the transmission channel If they are inadvertently removed re insert them immediately and redo the procedure Setting the transmission channel from step 1 e Make sure that the selected channel is the same on the transmitter and tuner being used in the same system e If you turn off the transmitter and then immediately turn it on right after setting the transmission channel the unit may not operate normally Wait a few seconds before turning it on again Setting the reception channel The procedure below is the same for all UWP series tuners URX P1 R1 M1 See Wireless microphone system frequency list on page 45 for details on the selectable channel groups and channels 1 Press down the SET button for more than one second Keep pressing the SET button
11. RF radio frequency indications The number of dots indicates the RF input level AF audio frequency indication Appears whenever the output audio signal is stronger than the reference level BATT battery indication Shows the battery condition For details see Power Supply on page 20 GP group CH channel indication Shows the reception channel group and channel number Each time you press the SET button the channel indication changes as follows For details see Settings on page 28 Reception channel LLL LIL i groupand number 1 Press ETS the 2 SET J button Reception J I frequency Accumulated battery use rt time 16 selection selection reset buttons Press these buttons to set the reception channel and frequency The button resets the accumulated battery use time to 00 00 These buttons can also be used to adjust the monitor level Q Battery compartment Accommodates two LR6 size AA alkaline batteries For details on how to insert the batteries see Power Supply on page 20 SET button Press to change display parameters For details see Settings on page 28 POWER switch Turns the power of the tuner ON or OFF OUTPUT audio output connector 3 5 mm diameter stereo mini jack Connect one end of the supplied XLR BMP conversion cable or the stereo mini plug BMP conversion c
12. UTX H1 This microphone is equipped with a built in antenna and a unidirectional dynamic microphone unit The RF power output can be set at 10 mW or at 2 mW Diversity tuner module URX M1 This tuner module can be incorporated into the MB 806A Tuner Base Unit or SRP X700P Powered Mixer 11 Precautions The UWP series product must be used within a temperature range of 0 C to 40 C 32 F to 104 F e Operating the UWP series product near electrical equipment motors transformers or dimmers may cause it to be affected by electromagnetic induction Keep the UWP series product as far from such equipment as possible The presence of the lighting equipment may produce electrical interference over the entire frequency range Position the UWP series product so that interference is minimized e To avoid degradation of the signal to noise ratio do not use the UWP series product in noisy places or in locations subject to vibration such as the following near electrical equipment such as motors transformers or dimmers near air conditioning equipment or places subject to direct air flow from an air conditioner near public address loudspeakers where adjacent equipment might knock against the tuner Keep the UWP series product as far from such equipment as possible or use buffering material e Clean the surface and the connectors of the UWP series product with a dry soft cloth Never us
13. UWP series is used in the following configuration examples Sample configurations for ENG Electronic News Gathering or EFP Electronic Field Production with a digital camcorder Portable diversity tuner URX P1 with the shoe mount adapter attached C lo lo DSR PDX10 PDX10P PD150 PD150P DVCAM Digital Camcorder Body pack transmitter or UTX B1 Portable diversity tuner URX P1 with the shoe mount adapter attached i CE Hand held microphone UTX H1 DSR PDX10 PDX10P PD150 PD150P DVCAM Digital Camcorder XLR BMP conversion cable supplied Lavalier microphone supplied 35 System Configurations Sample configurations for AV presentations Portable diversity tuner URX P1 with the shoe mount adapter attached Ra U e UTX H1 Body pack transmitter UTX B1 To DVD player PC or VTR etc SRP X700P Powered Mixer or Hand held microphone UTX H1 Half rack size diversity tuner URX R1 To DVD player PC or VTR etc I lo 6 SRP X700P A Powered Mixer AN 820 UHF Diversity tuner antenna module URX M1 NJ g Body pack tra
14. able here and the other end to the microphone input on a camcorder mixer or amplifier If the microphone input connector on the device connected to the tuner is a stereo mini jack connect the straight BMP plug 2 pole to the tuner and the L shaped stereo mini plug 3 pole to the microphone input connector on the device Half rack size diversity tuner URX R1 Front panel POWER switch Turns the power of the tuner ON or OFF Antennas a b The angle of the antennas can be adjusted manually MONITOR connector phone jack To monitor the tuner output connect the headphones to this connector and adjust the monitor level with the MONITOR control Use either stereo or monaural headphones MONITOR control Turn to adjust the output monitoring level through the headphones selection selection reset buttons Press these buttons to set the reception channel and frequency Display section RF radio frequency indications The number of dots indicates the RF input level AF audio frequency indication Appears whenever the output audio signal is stronger than the reference level GP group CH channel indication Shows the reception channel group and channel number Each time you press the SET button the channel indication changes as follows For details see Settings on page 28 17 Par
15. ansmitters are not set to the channels within the same channel group The channel plan which the UWP series components use is set so that no signal interference occurs when 2 or more transmitters are used simultaneously Set each transmitter to a different channel within the same channel group 40 Specifications Transmitters UTX B1 H1 Items common to all transmitters Oscillator type Crystal controlled PLL synthesizer Carrier frequencies 794 to 806 MHz Operating frequency band 12 MHz RF output level 10 mW 2 mW selectable Pre emphasis 50 us Reference deviation 5 kHz Frequency characteristics 50 Hz to 18 kHz Distortion 1 0 or less Signal to noise ratio 60 dB or more Tone signal 32 kHz Attenuation 0 to 21 dB in 3 dB steps Display Channel frequency audio level RF level accumulated battery use time Indicator Power on Power requirements 3 0 V DC two LR6 AA size alkaline batteries Battery life Approx 6 hours Body pack transmitter UTX B1 Antenna 1 44 wave length wire Audio input connector 3 5 mm dia mini jack Audio input level 60 dBV to 39 dBV Dimensions 63 x 100 x 27 mm 2 2 x 4 x 1 s inches w h d excluding the antennas Mass Approx 140 g 5 oz including batteries 41 Specifications Hand held microphone UTX H1 Microphone unit Dynamic Directivity Unidirectional Anten
16. ates the RF input level AF audio frequency indication Appears whenever the output audio signal is stronger than the reference level GP group CH channel indication Shows the reception channel group and channel number Each time you press the SET button the channel indication changes as follows For details see Settings on page 28 frequency Reception nae channel LiL LI I Press group and the number L ser Reception Tzn 122 button p 77400 3 selection selection reset buttons Press these buttons to set the reception channel and frequency 19 Power Supply This section explains the power supply for each component Half rack size diversity tuner URX R1 Connect the supplied AC adapter to the DC IN 9V connector on the rear panel and then connect the AC adapter to a wall outlet Diversity tuner module URX M1 When incorporated into another component e g MB 806A SRP X700P etc the tuner module draws its power from that component For details on the power supply to the diversity tuner module refer to the operating instructions of the component in which the diversity tuner module is installed Body pack transmitter UTX B1 hand held microphone UTX H1 and portable diversity tuner URX P1 These components can be powered by two LR6 size AA alkaline batteries for about six hours of continuous operation at 25 C 77
17. channels within the selected channel group 1 Turn off all the microphones and transmitters 2 Select the channel group on the tuner module installed into the slot 1 of the MB 806 3 After confirming that the channel group indication has stopped flashing about 10 seconds after you have selected the channel group keep pressing the button on the tuner module installed into the slot 1 of the MB 806 AII the tuner modules installed into the MB 806 are set to the available channels within the selected channel group After the automatic detection and selection of available channels finish you can change the group and channel on each tuner module manually e Do the automatic detection and selection of available channels with the channel group other than channel group 00 e When there are unavailable channels due to extraneous radio wave and the channel could not be selected on some tuner modules NO CH appears on the display of those tuner modules If this happens select the channel group with no interference from extraneous radio wave and repeat the procedure above Setting the attenuation level of the audio input The procedure below is the same for all UWP series transmitters UTX B1 H1 The attenuation level can be set during signal transmission 1 Do the following while there is no signal transmission Turn on the transmitter while pressing down the SET button and press the SET b
18. e Shoe mount adapter 1 Belt clip 2 with the URX P1 only 1 Stereo mini plug BMP conversion cable for use with the URX P1 only 1 e Microphone stand adapter 1 e Operation manual 1 UWP C2 The UWP C2 consists of a hand held microphone UTX H1 and a portable diversity tuner URX P1 When used in conjunction with a compact camcorder the UWP C2 makes a mobile system for ENG Electronic News Gathering or EFP Electronic Field Production purposes Hand held microphone Portable diversity tuner UTX H1 1 URX P1 1 Supplied accessories e Microphone holder 1 e Belt clip 1 e Shoe mount adapter 1 e XLR BMP conversion cable for use with the URX P1 only 1 Stereo mini plug BMP conversion cable for use with the URX P1 only 1 e Microphone stand adapter 1 e Operation manual 1 z Configuration of the Packages EEFETZEGEPTZZF R PTTEZZEWEWE e UWP S1 The UWP S1 consists of a body pack transmitter UTX B1 and a half rack size diversity tuner URX R1 The UWP S1 is suitable for constructing a wireless system for AV presentations Body pack transmitter Half rack size diversity tuner UTX B1 1 0 URX R1 1 Supplied accessories e Unidirectional lavalier e Wind screen 1 e Holder clip 1 microphone 1 e AC adapter 1 See Belt clip 1 e Operation manual 1 page 47 A UWP S2 The UWP S2 consists of a
19. e thinner benzene alcohol or any other chemicals since these may mar the finish 12 To prevent electromagnetic interference from portable communication devices The use of portable telephones and other communication devices near the UWP series product may result in malfunction and interference with audio signals It is recommended that portable communication devices near the UWP series product be turned off Parts Identification AF audio frequency indication Appears whenever the input audio signal is stronger than the reference level Body pack transmitter UTX B1 RF antenna output indication Appears during signal transmission from the antenna RF antenna output level indication Shows the RF output level setting For details see Setting the RF output level on page 32 BATT battery indication Shows the battery condition For details see Power Supply on page 20 CH channel indication Shows the transmission channel Each time you press the SET button in transmission mode the channel indication changes as follows For details see Settings on page 28 Antenna Audio input connector Connect the supplied lavalier microphone here Power indicator Transmission i mr Lights up red when the transmitter is channel NN I tuned on J Transmission lt u 25 a Display section frequency L J utc 3 a 1 but
20. ed from the slot Installing a diversity tuner module URX M1 into an SRP X700P Powered Mixer The SRP X700P Powered Mixer can accommodate up to 2 diversity tuner Diversity modules URX M1 tuner module URX M1 1 Remove the tuner slot cover from the SRP X700P and inspect the top and bottom sides of the diversity tuner module Then holding the tuner module on both sides insert it into the slot Diversity tuner module URX M1 Removing the diversity tuner module URX M1 Insert a screwdriver with a shaft diameter of between 2 to 4 mm and a shaft length of 30 mm or longer into the hole under the lower part of the tuner slot and remove the tuner module 27 Setting the transmission channel The procedure below is the same for all UWP series transmitters UTX B1 H1 See Wireless microphone system frequency list on page 45 for details on the selectable channel groups and channels 1 Turn on the transmitter while pressing down the SET button Keep pressing the SET button until the display section parameters that were displayed when the unit was last turned off start to flash 2 Press the SET button repeatedly until the channel number or frequency indication appears 3 Press the or button to select the channel number or frequency Pressing the button cycles the indication in the order shown in the tables in Wireless microphone system frequency list on page
21. expiration date printed on the new batteries before using them 1 2 3 4 BATT indication Lights Lights Lights Flashes mm Lm G koi Battery status Good Less than Less than Almost 50 charged 20 charged drained 21 Power Supply The indicated battery condition may not be correct if the batteries were not new when installed If you plan to use the component for a long period it is recommended that you replace the batteries with brand new ones Notes on batteries Batteries may leak or explode if mistreated Be sure to follow these instructions e Be sure to install the batteries with the correct polarity e Always replace the two batteries together e Do not use different types of batteries or old and new one together e The batteries are not rechargeable e When not using the component for a long period of time remove the batteries to avoid leakage If the batteries do leak clean all leakage from the battery compartment and the component Leakage left in the compartment and the component may cause poor battery contact If there seems to be poor battery contact consult your Sony dealer 22 Attachment and Installation Procedures This section describes the procedures for attaching the supplied accessories to components and the installation of the diversity tuner module URX M1 into the MB 806A Tuner Base Unit or SRP X700P Powered Mixer Attaching the supplied accessories
22. g is LM stored in memory and the normal display resumes Note that 3 Press the button to select H 10 monitor level setting is effective mW or press the button to after you turn off the tuner then select L 2 mW turn it on again Set the POWER switch to OFF to complete the setting or press the SET button to set other items The results are stored in memory The change becomes effective the next time you turn on the transmitter by setting the POWER switch to ON Setting the monitor level portable diversity tuner URX P1 only You can set the monitor level for monitoring the tuner output within the range of 01 to 24 1 While the parameters on the display section are not flashing press the or button once The monitor level indication appears in the display section 33 Operation The procedure below is the same for all UWP series components UTX B1 H1 and URX P1 R1 M1 1 Make all necessary connections on the tuner For examples of UWP series component connections see System Configurations on page 35 2 Set the transmission channel on the transmitter and then turn off the unit For details on setting the transmission channel see Setting the transmission channel on page 26 3 Turn on the tuner The parameters that were in the display section when the tuner was last turned off appear again Before turning on the tuner turn down the v
23. hand held microphone UTX H1 and a half rack size diversity tuner URX R1 The UWP S2 is suitable for constructing a wireless system for AV presentations Hand held microphone Half rack size diversity tuner UTX H1 1 URX R1 1 Supplied accessories e Microphone holder 1 e AC adapter 1 See page 47 KO e Operation manual 1 Configuration of the Packages UWP X1 The UWP X1 consists of a body pack transmitter UTX B1 and a diversity tuner module URX M1 By installing the tuner module into a tuner base unit or a powered mixer the system construction to meet the desired purpose of use and required system scale becomes possible Body pack transmitter Diversity tuner module UTX B1 1 URX M1 1 Supplied accessories e Unidirectional lavalier e Wind screen 1 Holder clip 1 microphone 1 Q Belt clip 1 e Operation manual 1 UWP X2 The UWP X2 consists of a hand held microphone UTX H1 and a diversity tuner module URX MI By installing the tuner module into a tuner base unit or a powered mixer the system construction to meet the desired purpose of use and required system scale becomes possible Hand held microphone Diversity tuner module UTX H1 1 URX M1 1 Supplied accessories e Microphone holder 1 e Operation manual 1 Each of the UWP C1 C2 S1 S2 X1 X2 wireless microphone packages referred to as the UWP
24. ing For details see Setting the RF output level on page 32 BATT battery indication Shows the battery condition For details see Power Supply on page 20 CH channel indication Shows the transmission channel Each time you press the SET button the channel indication changes as follows For details see Settings on page 28 Transmission Emm channel Transmission mir 1 41 Press frequency 111 IZA the SET 4 button Attenuation levelofthe H77 05 input signal Accumulated x battery use woe time selection selection reset buttons Press these buttons to set the transmission channel frequency or attenuation level of the input signal The button resets the accumulated battery use time to 00 00 Q SET button Press to change display parameters For details see Settings on page 28 0 dBu 1 UVEmF Portable diversity tuner URX P1 Antennas a b The angle of the antennas can be adjusted manually MONITOR connector 3 5 mm diameter stereo mini jack To monitor the tuner output connect the headphones to this connector RF radio frequency indicator Indicates the strength of the RF input signal On in green RF input is 15 dBu or more Off RF input is less than 15 dBu 15 Parts Identification Display section
25. ith an adapter for mounting the tuner on the compact camcorder DSR PDX10 PDX10P PD150 PD150P etc UWP S1 Body pack transmitter UTX B1 This is a small and lightweight transmitter with a crystal controlled PLL phase lock loop synthesized system and a BMP type microphone input connector The RF power output can be set at 10 mW or at 2 mW Half rack size diversity tuner URX R1 This tuner employs a space diversity system with little signal dropout and two angle adjustable antennas It comes with two types of audio connectors 1 4 inch jack and XLR type on the rear panel UWP S2 Hand held microphone UTX H1 This microphone is equipped with a built in antenna and a unidirectional dynamic microphone unit The RF power output can be set at 10 mW or at 2 mW Half rack size diversity tuner URX R1 This tuner employs a space diversity system with little signal dropout and two angle adjustable antennas It comes with two types of audio connectors 1 4 inch jack and XLR type on the rear panel UWP X1 Body pack transmitter UTX B1 This is a small and lightweight transmitter with a crystal controlled PLL phase lock loop synthesized system and a BMP type microphone input connector The RF power output can be set at 10 mW or at 2 mW Diversity tuner module URX M1 This tuner module can be incorporated into the MB 806A Tuner Base Unit or SRP X700P Powered Mixer UWP X2 Hand held microphone
26. na 1 44 wave length wire internal Dimensions 9 52 x 240 mm 2 s x 9 a inches dia length Mass Approx 300 g 11 oz including batteries 42 Tuners URX P1 R1 M1 Items common to all tuners Type of reception Space diversity Oscillator type Crystal controlled PLL synthesizer Reception frequencies 794 to 806 MHz Operating frequency band 12 MHz Signal to noise ratio 60 dB or more De emphasis 50 us Reference deviation 5 kHz Frequency characteristics 50 Hz to 18 kHz Distortion 1 0 or less at 1 kHz modulation Tone signal 32 kHz Indicator RF input level Portable diversity tuner URX P1 Antenna 1 44 wave length wire adjustable angle Squelch level 15 dBu Audio output level 58 dBm Audio output connector 3 5 mm dia mini jack Headphones output level 5 mW 160 Display Channel frequency audio level RF level accumulated battery use time monitor level Power requirements 3 0 V DC two LR6 AA size alkaline batteries Battery life Approx 6 hours Dimensions 63 x 100 x 30 mm 2 2 x 4 x 1 3 16 inches w h d excluding the antennas Approx 180 g 6 oz including batteries Mass Half rack size diversity tuner URX R1 Antenna 1 44 wave length wire adjustable angle Squelch level 25 dBu Balanced audio output level 28 dBm LINE level 58 dBm MIC level selectable Unbalanced audio output level 30 dBm A
27. nd Keep pressing the SET button until the display seciton parameters start to flash 2 Press the SET button repeatedly until the frequency indication appears and starts flashing PALL hey TORA IZ CD EJ HH 3 Press the or button to select the frequency 4 When the desired frequency appears leave the tuner for about 10 seconds until the selected channel frequency stops flashing and the selection is stored in memory e When you are setting the reception channel the tuner can be used to receive signals e Do not remove the batteries while setting the reception channel If they are inadvertently removed re insert them immediately and redo the procedure Setting the reception channel from step 1 e Make sure that the selected channel is the same on the transmitter and tuner being used in the same system 30 e If you turn off the tuner and then immediately turn it on right after setting the reception channel the unit may not operate normally Wait a few seconds before turning it on again Detecting and selecting the available channels automatically diversity tuner module URX M1 only When multiple diversity tuner modules URX M1 are installed into the MB 806 to perform simultaneous multiple channel operation select the channel group on the tuner module installed into the slot 1 of the MB 806 then all the tuner mudules installed into the MB 806 can be set to different
28. nsmitter UTX B1 XLR cable with the XLR BMP conversion cable supplied Lavalier microphone supplied BNC cable XLR cable or pin cable 36 Sample configuration of a PA system Hand held microphone UTX H1 N AN 820 UHF antenna Diversity rego Ol Bear OF Body pack transmitter UTX B1 To DVD player PC i HEF or VTR etc SRP X700P Powered Mixer LEJE Lavalier microphone supplied Diversity tuner BNC cable module URX M1 XLR cable XLR cable or pin cable 1 WD 820A Antenna Divider 2 MB 806A Tuner Base Unit 3 SRP X100 Audio Mixer 37 Error Messages When a problem occurs one of the following error messages may appear on the display Messages Meanings Remedy Err 01 An error has occurred in the backup memory Contact your Sony dealer data Err 02 The PLL synthesized circuit is abnormal Restart the unit If the message appears again contact your Sony dealer Err 03 The battery voltage exceeds the allowable limit Use the specified batteries Body pack transmitter UTX B1 hand held microphone UTX H1 portable diversity tuner URX P1 only 38 Troubleshooting If you have any problem using the UWP system use the following checklist Should any problem persist consult your Sony dealer Symp
29. olume of the equipment connected to the tuner Otherwise noise will be produced when the tuner is turned on 4 Set the reception channel on the tuner For details on setting the reception channel see Setting the reception channel on page 29 5 Turn on the transmitter 34 If noise is heard Depending on the environment where the UWP series components are installed external noise or radio waves may disrupt transmission on certain channels When selecting a channel under these circumstances turn off the transmitter Then on the tuner select a channel for which the RF indications do not appear in the display section or for which the RF indicator does not light up i e a channel free from noise or radio wave interference Set the same channel on the transmitter To prevent interference or noise please take the following precautions e Do not use two or more transmitters with the same wireless channels e When operating two or more UWP series simultaneously set each series to a different channel within the same channel group e Keep the reception antenna and the transmitter separated more than 3 meters 9 feet 11 inches e When operating two or more UWP series simultaneously with the same channel group make sure that they are at least 100 meters 330 feet apart but within clear sight of each other The actual distance may differ depending on the circumstances System Configurations The
30. s microphones transmitters Group for transmitter and tuner Group 00 TV 68 TV 69 CH MHz CH MHz CH MHz CH MHz 68 01 794 125 68 25 797 125 69 01 800 125 69 25 803 125 68 02 794 250 68 26 797 250 69 02 800 250 69 26 803 250 68 03 794 375 68 27 797 375 69 03 800 375 69 27 803 375 68 04 794 500 68 28 797 500 69 04 800 500 69 28 803 500 68 05 794 625 68 29 797 625 69 05 800 625 69 29 803 625 68 06 794 750 68 30 797 750 69 06 800 750 69 30 803 750 68 07 794 875 68 31 797 875 69 07 800 875 69 31 803 875 68 08 795 000 68 32 798 000 69 08 801 000 69 32 804 000 68 09 795 125 68 33 798 125 69 09 801 125 69 33 804 125 68 10 795 250 68 34 798 250 69 10 801 250 69 34 804 250 68 11 795 375 68 35 798 375 69 11 801 375 69 35 804 375 68 12 795 500 68 36 798 500 69 12 801 500 69 36 804 500 68 13 795 625 68 37 798 625 69 13 801 625 69 37 804 625 68 14 795 750 68 38 798 750 69 14 801 750 69 38 804 750 68 15 795 875 68 39 798 875 69 15 801 875 69 39 804 875 68 16 796 000 68 40 799 000 69 16 802 000 69 40 805 000 68 17 796 125 68 41 799 125 69 17 802 125 69 41 805 125 68 18 796 250 68 42 799 250 69 18 802 250 69 42 805 250 68 19 796 375 68 43 799 375 69 19 802 375 69 43 805 375 68 20 796 500 68 44 799 500 69 20 802 500 69
31. series hereafter combines a transmitter body pack transmitter UTX B1 or hand held microphone UTX H1 and a receiver portable diversity tuner URX P1 half rack size diversity tuner URX R1 or diversity tuner module URX M1 The UWP series can be used with a compact camcorder for ENG Electronic News Gathering purposes and with a powered mixer for AV presentations or as a PA public address system The UWP series is not compatible with conventional WRT series transmitters WRR series tuners or WRU series tuner units The features of each package are described below UWP C1 Body pack transmitter UTX B1 This is a small and lightweight transmitter with a crystal controlled PLL phase lock loop synthesized system and a BMP type microphone input connector The RF power output can be set at 10 mW or at 2 mW 10 Portable diversity tuner URX P1 This tuner employs a space diversity system with little signal dropout and two angle adjustable antennas It comes with an adapter for mounting the tuner on the compact camcorder DSR PDX10 PDX10P PD150 PD150P etc UWP C2 Hand held microphone UTX H1 This microphone is equipped with a built in antenna and a unidirectional dynamic microphone unit The RF power output can be set at 10 mW or at 2 mW Portable diversity tuner URX P1 This tuner employs a space diversity system with little signal dropout and two angle adjustable antennas It comes w
32. tom The unit does not turn on Meanings Remedy The polarity orientation of the batteries in the battery compartment is incorrect Insert the batteries with the correct polarity orientation The batteries are exhausted gt Replace the batteries with new ones The battery terminals in the transmitter are dirty gt Clean the and terminals with a cotton swab The batteries become drained quickly The batteries are exhausted gt Replace the batteries with new ones Manganese batteries are being used Use alkaline batteries The battery life of a manganese battery is less than half that of an alkaline battery The UWP series is being used under cold conditions The batteries drain quickly under cold conditions The channel cannot be changed An attempt was made to change the channel by pressing the SET button only Restart the unit while holding down the SET button Then change the channel with the and buttons There is no sound The channel setting on the transmitter is different from that on the tuner gt Use the same channel setting on both the transmitter and tuner The RF indications RF indicator on the tuner do not appear at all or does not turn on gt Confirm that the transmitter is turned on The sound is weak The attenuation level on the transmitter is too high gt The output level of the transmitter is low Press the button on the
33. ton Attenuation levelofthe ATT 05 AF RF BA input signal _ I ped H Accumulated ma time 13 Parts Identification selection selection reset buttons Press these buttons to set the transmission channel frequency or attenuation level of the input signal The button resets the accumulated battery use time to 00 00 QO Battery compartment Accommodates two LR6 size AA alkaline batteries For details on how to insert the batteries see Power Supply on page 20 SET button Press to change and enter display parameters For details see Settings on page 28 POWER switch Turns the power of the transmitter ON or OFF Hand held microphone UTX H1 The rear side of the battery compartment Power indicator Lights up red when the microphone is turned on POWER switch Turns the power of the microphone ON or OFF Battery compartment Accommodates two LR6 size AA alkaline batteries For details on how to insert the batteries see Power Supply on page 20 Display section AF audio frequency indication Appears whenever the input audio signal is stronger than the reference level RF antenna output indication Appears during signal transmission from the antenna RF antenna output level indication Shows the RF output level sett
34. transmitter in attenuation level setting mode to decrease the attenuation level The volume on the amplifier or mixer is low Adjust the volume Body pack transmitter UTX B 1 hand held microphone UTX H1 portable diversity tuner URX P1 only 39 Troubleshooting Symptom There is distortion in the sound Meanings Remedy The attenuation level of the transmitter is too low gt The input level of the tuner is extremely high Press the button on the transmitter in attenuation level setting mode to raise the attenuation level The transmitter and the tuner are set to different channels gt Set the transmitter to the same channel There is sound interruption or noise The RF indications on the tuner appear the RF indicator lights up even when the transmitter is off Jamming radio waves are being received Determine which channels are usable i e channels for which the RF indications on the tuner do not appear or for which the RF indicator on the tuner does not light up and set the tuner and transmitter to the same usable channel When two or more transmitters are used simultaneously use another channel group that is unaffected by jamming radio waves The transmitter and the tuner are set to different channels gt Set the transmitter to the same channel Two or more transmitters are set to the same channel Set each transmitter to a different channel The tr
35. ts Identification Reception __ _ _ _ channel LLG Lt Press group and the number l SET Reception button frequency RF radio frequency indicator Indicates the strength of the RF input signal On in green RF input is 25 dBu or more Off RF input is less than 25 dBu SET button Press to change display parameters For details see Settings on page 28 TUNER OUTPUT audio output connector XLR type Connect to the audio input connector of a mixer or amplifier etc LEVEL audio output level switch Sets the output level of the TUNER OUTPUT connector XLR type to 28 dBm or 58 dBm Select the setting according to the input level of the equipment connected to the tuner TRS PHONE tuner audio output connector 1 4 inch jack Connect to the audio input connector of a mixer or amplifier etc The output level from this connector is 30 dBm 0 dBu 1 Vem 18 DC IN 9V DC power input connector Connect the supplied AC adapter here Diversity tuner module URX M1 SET button Press to change display parameters For details see Settings on page 28 RF radio frequency indicator Indicates the strength of the RF input signal On in green RF input is 25 dBu or more Off RF input is less than 25 dBu Display section RF radio frequency indications The number of dots indic
36. udio output connectors XLR 3 32 type balanced 1 4 inch jack unbalanced LINE level only Headphones output level 5 mW 160 Display Channel frequency Power requirements 9 0 V DC Dimensions 212 x 44 x 209 mm 8 7 s x 1 3 4 x 8 1 4 inches w h d excluding the antennas 43 Specifications EFTETFTY FX TFTP EEE ZEE FK Mass Approx 1 3 kg 2 Ib 14 oz Diversity tuner module URX M1 Squelch level 25 dBu Display Channel frequency Dimensions 57 x 26 x 121 mm 2 4 x 1 1 16 X 4 7 s inches w h d Mass Approx 150 g 5 oz Design and specifications are subject to change without notice 44 Appendix Wireless microphone system frequency list The following tables show the channels and frequencies selectable on your wireless microphone transmitter and tuner The group 00 permits the unit to operate on any of 47 carrier frequencies in 125 kHz steps of TV channels 68 and 69 For the setting procedures of the transmitting channels frequencies on your unit refer to the Instruction Manual of your unit Be sure to save this list together with the Instruction Manual of your unit Guidance on the use of a multi channel system When building up a multi channel system Sony recommends that one of the groups listed under Groups for the tuner is selected to avoid mutual interference from other Sony wireles
37. until the display section parameters start to flash Press the SET button repeatedly until the channel group and the channel number indications appear The channel group indication starts to flash Hold down the or button to change the channel group faster When the desired channel group number appears press the SET button The selected group is entered The right four digits start to flash to allow the selection of the channel number zo LIAS LI AAAF mo a if 0 Press the or button to select the channel number The channel indication changes in the order shown in the tables in Wireless microphone system frequency list on page 45 Example When the channel group 00 Press the or button to select the channel group Pressing the button cycles the indication in the order shown in the tables in Wireless microphone system frequency list on page 45 Pressing the button cycles the indications in the opposite direction is selected mmr l ZZM ZZL ZZL t mer H DIT I 4 Tn t NAT I H zza m t aau GJL I 6 When the desired channel number appears leave the tuner for about 10 seconds until the selected channel number stops flashing and the selection is stored in memory 29 Settings To selct the channel by frequency indication 1 Press the SET button for more than one seco
38. utton repeatedly until the attenuation level indication appears in the display section Ai arom iw EPR E Do the following while there is signal transmission Press the SET button repeatedly until the attenuation level indication appears in the display section Press the or button to select the attenuation level The selectable range is from 0 dB to 21 dB in steps of 3 dB the factory setting is 0 dB Do the following while there is no signal transmission Set the POWER switch to OFF to complete the setting or press the SET button to set other items The results are stored in memory The change becomes effective the next time you turn on the transmitter by setting the POWER switch to ON 31 Settings Resetting the accumulated battery use time indication The procedure below is the same for all UWP series transmitters UTX B1 H1 and the portable diversity tuner URX P1 The accumulated battery use time is the total time in hours and minutes that the batteries have been used It is recorded whenever the transmitter microphone tuner is on Reset the indication to 00 00 whenever you replace the batteries 1 aFor transmitters UTX B1 H1 Turn on the unit while pressing down the SET button 1 bFor the portable diversity tuner URX P1 Press down the SET button for more than one second Keep pressing the SET button until the display section parameters start to flash
Download Pdf Manuals
Related Search