Sony DRN-XM01C User's Manual
Contents
1. Clean the mounting surface before mounting Cable guide 2 Mount the water proof cushion on the back side of the trunk lid To prevent rain water leakage inside the car along the cord mount the water proof cushion above the rubber packing when the trunk lid is closed Cable guide Water proof cushion LLLLAAA ISN SSY Trunk lid Rubber packing e Cut the cable guide if required e It is difficult to attach the cable guide to a body or window which has fluorine resin coating For DRN XMO1C KMO1CK Connecting the Unit to the Cigarette Lighter Socket Car cassette deck to a cassette insertion slot to a cigarette lighter socket Car connecting pack Power lamp Car battery cord TER XM antenna to the ANT to the ANT SAT jack TER jack toate to the DC IN 6V LINE OUT jack jack When the electric power is supplied to the car battery cord the power lamp lights up Notes e Route the cords so that they will not interfere with your driving e Take care not to accidentally insert a portion of the car connecting pack cord into the cassette insertion slot This may cause the cord to break or damage the car cassette deck e To disconnect the cord from your audio equipment pull it out by grasping the plug Never pull it by the cord e If the inside of the cigarette lighter socket is dirty with cigarette ash the cigarette lighter plug may be heated due to2. After installing and connecting the unit run cord so as not to interfere with the operation of the vehicle Run and fix the cord on the passenger side of the center console with the supplied cord clamp e Clean the mounting surface before installing the cord clamp e Leave the installed cord clamp for 24 hours before installing the cord Otherwise the cord clamp may come off because of weak attachment Note Make sure the cord does not get caught in the sliding rails under the front seats or the front doorsills as this may cause the cord to be severed For DRN XMO1H XMO1HK Using the Unit on House Current Use the AC power adaptor and the audio cord supplied with DRN XM01H XM01HK Attaching the Home Stand Tighten the screw at the bottom of the home stand To the stand to secure the cradle receptacle at the bottom of the cradle Be Z Connecting the Unit to the input jacks to an AC outlet of the audio equipment XM antenna Audio cord AC power adaptor SAT TER tothe ANT to the ANT SAT jack TER jack to the LINE OUT jack Note on the DC plug of the AC power adaptor This AC power adaptor uses a unified polarity type plug JEITA standard Damage will occur if it is connected to a DC power input jack without the polarity symbol or with another symbol If the jack of your audio equipment does not match the AC power adaptor consult your dealer S
3. body The antenna cannot be installed on an aluminum or plastic body with the magnet In this case use the supplied seal Painting the antenna The antenna can be painted according to the body color of the car however do not use paint that contains metal powder This may cause deterioration or inability of reception Do not disassemble the antenna when painting Placement of the car antenna Place the antenna on a flat and even surface on your car roof The angle from the ground to the satellite should be about 20 60 degrees If you place the antenna on the trunk lid make sure your car roof does not block the satellite signal Depending on where you live you may be able to receive radio waves that are retransmitted by ground repeaters Figure of the top Water proof cushion Cord clamp Inside of the trunk Rubber packing Put the water proof cushion parallel on the rubber packing using the double sided adhesive tape Figure of the side Water proof cushion Rubber e packing Double sided Cord clamp adhesive tape Put the water proof cushion on the rubber packing with the flat surface downward using the double sided adhesive tape Be sure to install the antenna firmly on a flat surface Do not install on the corner of the roof Figure of the back Water proof cushion Rubber packing Cord clamp XM antenna Cable guide Cable guide Double sided adhesive tape Cord cl
4. circuit e Do not break up the battery or throw it into a fire which might cause it to explode Carefully dispose of the used battery Note When the unit is not to be used for a long period of time remove the battery to avoid damage from battery leakage and corrosion Specifications Accessories supplied XM antenna 1 Remote commander 1 For DRN XM01C XM01CK XMOIR Car cradle 1 Car stand 1 Screw 5 Cover 1 Water proof cushion 1 Cable guide 3 Cord clamp 4 Cushion with the double sided adhesive tape 1 Seal 1 For DRN XM01C XMOI1CK only Car battery cord 1 Car connecting pack 1 For DRN XMOIR only RF modulator 1 For DRN XM01H XMO01HK Home cradle 1 Home stand 1 Audio cord 1 AC power adaptor 1 Optional accessories AC power adaptor AC E60A Car battery cord DCC E260 Car connecting pack CPA 9C Precautions e Do not install the unit where the ambient temperature exceeds 55 C 131 F it will be exposed to direct sunlight or hot air from a heater it will be exposed to rain water or high humidity it will be exposed to a lot of dust it will be subject to excessive vibration hinder normal driving activities jeopardize the passengers e Be sure to turn off the power of each component before making the connections For DRN XM01C XMO1CK Customers Be sure to check that the voltage of the equipment connected to this unit is correct Incorrect voltage
5. may cause the equipment to malfunction e This unit is designed for negative ground 12 or 24 V DC operation only e Avoid high temperatures such as direct sunlight or hot air from the heater e You cannot use this unit with some car cassette deck e Used with some car cassette decks the car connecting pack may rattle This is not a malfunction of the car connecting pack Note on the DC plug of the car battery cord This car battery cord uses a unified polarity type plug JEITA standard Damage will occur if it is connected to a DC power input jack without the amp gt lt polarity symbol or with another symbol For DRN XMO1R Customers e This unit is designed for negative ground 12 V DC operation only e Before making connections disconnect the earth terminal of the car battery to avoid short circuits e Connect the red power input leads only after all other leads have been connected Be sure to connect the red power input lead to the positive 12 V power terminal which is powered when the ignition switch is in the accessory position e Run all earth wires to a common earth point For DRN XM0O1H XMO1HK Customers On installing the AC power adaptor Do not place the AC power adaptor in a location where it is subject to extreme high temperature E g in a car with its windows closed direct sunlight or near a heat source mechanical vibration or shock a magnetic field E g near a magnet speake
6. to avoid the direct sunlight e Do not install the cradle the main unit and RF modulator in the following places Underneath the driver s seat There may be a danger of the unit getting lodged under the brake pedal On the door or ceiling There may be a danger of the unit falling down or obscuring the driver s view while driving For DRN XM01C KMO1CK XMO1R Installing the XM Antenna to your Car The bottom surface of the XM antenna is made of a magnet Install the antenna horizontally in a location where the radio wave from the satellite is not interrupted by the body of the car E g roof or trunk lid SK eo CO Notes on installing the antenna to your car e Mount the antenna gently so that it does not damage the body of the car e Do not leave the cord slackened outside of the car e Use the cord clamp when fixing the cord if required e When removing the antenna do not pull it by the cord This may cause the cord to come off the antenna because of the powerful magnet e The antenna cord is charged with the XM signal and the power supply to the antenna When wiring the antenna be careful not to pinch the cord in the moving parts of the car The damaged cable may cause a malfunction of the antenna and the main unit e When washing the car in an automatic car wash remove the antenna Otherwise it may damage the body of the car Installing the antenna to an aluminum or plastic
7. 3 234 493 12 1 SONY Digital Audio Receiver Accessory Kit Installation Guide OWNER S RECORD The model number is located on the bottom and serial number also on the bottom Record the serial number in the space provide below Refer to these numbers whenever you call upon your Sony dealer regarding this product Model No Serial No DRN XM01C DRN XM01R DRN XM01H DRN XM01CK DRN XM01HK SATELLITE RADIO Printed on 100 recycled paper using VOC Volatile Organic Compound free vegetable oil based ink Sony Corporation 2001 Printed in Japan http www sony net For customers in the USA Please register this product on line at http www sony com productregistration Proper registration will enable us to send you periodic mailings about new products services and other important announcements Registering your product will also allow us to contact you in the unlikely event that the product needs adjustment or modification Thank you For DRN XM0O1H KMO1HK Customers To prevent fire or shock hazard do not expose the unit to rain or moisture You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protecti
8. abnormal contact Be sure to clean the inside of the cigarette lighter socket before inserting the plug e After using the receiver eject the car connecting pack from the car cassette deck and disconnect the car battery cord from the receiver and the cigarette lighter socket e Do not use the receiver when the car s engine is not running Using the Car Connecting Pack 1 Turn down the volume of the car cassette deck 2 Set the tape selector to the normal TYPE I position and the DOLBY NR REPEAT or BLANK SKIP switch to the OFF position if such are equipped 3 Insert the car connecting pack into the cassette deck 4 Start playback on the car cassette deck 5 Adjust the volume If no sound is heard or the car connecting pack is removed change the playback direction on the car cassette deck To Remove the Car Connecting Pack Press the eject button of the car cassette deck Note You cannot use this car connecting pack with certain car cassette decks Fuse Replacement Fuse 1 A to tighten to remove Cigarette lighter plug End of the plug 1 Pull the cigarette lighter plug out of the cigarette lighter socket 2 Detach the end of the plug by turning it counterclockwise 3 Replace the fuse with a new one 4 Reattach the end of the plug by turning it clockwise firmly Notes e When replacing the fuse be sure to use one with the correct amperage as stated on the fuse case 1 A 125 V 20 mm e Do not use a
9. amp e Be sure to install the cord clamp in a lower position where the water proof cushion is mounted Otherwise it will cause a water leak into the trunk e Clean the mounting surface before installing the cord clamp e Leave the installed cord clamp for 24 hours before installing the cord Otherwise the cord clamp may come off because of weak attachment e Cut the cable guide if required e It is difficult to attach the cable guide to a body or window which has fluorine resin coating Leading the antenna cord into the car through the space between door and body When installing the antenna on the roof you can also lead the antenna cord into the car through the space between door and body Cord clamp Cord clamp P Water proof cushion e Clean the mounting surface before installing the cord clamp e Leave the installed cord clamp for 24 hours before installing the cord Otherwise the cord clamp may come off because of weak attachment Mounting the Antenna with the Supplied Seal and Cushion with the Double sided Adhesive Tape Attach to the antenna S gt Cushion with the double sided ON Pa adhesive tape Seal of Attach to the trunk lid Note When removing the seal preheat the mounting surface with a hairdryer then pull up slowly to remove or use a commercially available solvent to remove the seal Installing the Antenna on the Trunk Lid 1 Mount the antenna on the trunk lid
10. ff the antenna line is connected to the car audio Besides you can set the RF modulator to always cut off the antenna line and output the XM radio sound to the car audio in this case you cannot hear the normal FM broadcast POWER SEL select switch POWER SEL P A 1 Normal use detecting more than 100 mA load 2 Not used detecting more than 50 mA load ON Not used cutting off the antenna line The optional antenna converter cord XA 82 is AUDIO required The shape of the antenna terminal is different depending on the model of the car Others The optional antenna converter cord may be required Check with the retailer to the car antenna Changing the Transmitting Frequency This unit changes the signal of the XM satellite radio broadcast into an FM frequency and outputs the sound through an FM tuner There may be interference noise while playing the receiver when the frequency selected for the receiver is used for transmitting the actual FM broadcast In such a case change the transmitting frequency on the unit The factory set is 87 9 MHz Frequency select switch F SEL Default 4 87 9 MHz 88 5 MHz 123 1 2 3 4 88 1 MHz 88 7 MHz B 88 9 MHz Note When you change the frequency on the unit be sure to tune your FM tuner to the newly selected one For the DRN XM01C XMO1CK XMO1R When the Installation and Connections Have Been Made Securing the Cord
11. it where it may obstruct your view through the windshield or your view of your vehicle s indicator displays e Do not install the unit where it may hinder the function of safety devices such as an air bag Doing so may prevent the air bag from functioning properly in the event of an accident e The installation and use suggestions contained in this manual are subject to any restrictions or limitations that may be imposed by applicable law purchaser should check applicable law for any restrictions or limitations before installing and or operating this product e Failure to follow these safety instructions and warnings may result in a serious accident Parts for Installation and Connection for DRN XM01C XM01CK XMO1R XM antenna 1 Remote commander 1 Car cradle 1 Water proof cushion 1 S Cord clamp 4 Cushion with the Seal 1 double sided H adhesive tape 1 lt 5 Screw 5 Cover 1 Cable guide 3 for DRN XM0O1C XMO1CK only Car battery cord 1 Car connecting pack 1 for DRN XM01H XMO1HK Home cradle 1 XM antenna 1 Remote commander 1 Home stand 1 Audio cord 1 For DRN XM01C KMO1CK XMO1R Installing the Cradle in your Car Install the cradle with the supplied car stand 1 Choose the mounting position then shape the base of the stand to match the mounting surface Note Bend the base gently so there are no gaps between the base and the mounting s
12. on against harmful interfer ence in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accor dance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation For all Models Caution e Do not operate the unit in a way that might divert your attention from driving safely As a driver you alone are responsible for safely operating your vehicle in accordance with traffic safety laws at all times e Do not install the un
13. piece of wire instead of a fuse e If the replaced fuse opens again consult your dealer For DRN XMO1R Connecting the Unit to your Car with a RF Modulator to the 12 V power terminal which is powered when the ignition key switch is Fuse 1 A in the accessory position Be sure to connect the black earth lead to it first Power connecting cord Supplied XM antenna A POWER a A ANT Black to a metal point on the car Car audio Antenna connecter Connect it as follows when a diversity antenna is used for the car audio TOYOTA Connect to the bigger antenna connector RF Modulator NISSAN SAT TER DC OUT zZ to the ANT SAT jack to the ANT TER jack to the LINE OUT jack Fuse Replacement If the fuse blows check the power connection and replace the fuse If the fuse blows again after replacement there may be an internal malfunction Warning Use a fuse with the specified amperage rating Use of a higher amperage fuse may cause serious damage Setting the POWER SELECT Switch This RF modulator supplies power to the receiver and detects the on off state by monitoring the load of the power When the receiver is turned on the RF modulator automatically cuts off the antenna line and directly outputs the sound of the receiver to the car audio with the selected FM frequency This prevents the sound from disturbing the FM broadcast signal When the receiver is turned o
14. r or TV excessive dust On operating the AC power adaptor e Make sure the current and voltage of the equipment matches that of the outlet e For safety if the input current is too high the unit will automatically shut down e Do not use the unit near a TV set If you place equipment too close to the unit while they are being used you may experience some interference e To prevent damage be careful not to drop or otherwise cause a mechanical shock to the unit e After using disconnect the unit from the wall outlet and the equipment e Disconnect the unit from the AC outlet by pulling on the plug Do not pull on the cord e To avoid short circuiting do not allow the terminals of the unit or connector to touch any metal object e Use only the recommended AC power adaptor For all Customers On cleaning e Clean the unit with a soft dry cloth If the unit is very dirty wipe it off with a soft cloth lightly moistened with a mild detergent solution and then wipe with a soft dry cloth e Do not use any type of solvent such as alcohol thinner or benzine as it may damage the finish of the cabinet e If you use any chemical cleaner observe the instructions provided with the product e If the cabinet of the unit is splashed with any type of solvent such as insecticide or remains in contact for a long time with rubber or vinyl the finish or the cabinet may be damaged
15. urface 2 Clean the mounting surface well 3 Peel off the protective film from the base of the stand and attach the base to the mounting surface Make sure the base attaches to the mounting surface completely Notes e The double sided tape will not stick firmly if the mounting surface temperature is lower than 20 C 68 F Use a hairdryer etc to warm up the mounting surface before mounting e Consider the mounting position carefully beforehand If you change the position after mounting the double sided tape will weaken e When removing the stand preheat the mounting surface with a hairdryer then slowly pull up to remove or use a commercially available solvent to remove the seal 4 Fix the stand with the supplied screws Note Before drilling holes in the mounting surface make sure there is nothing behind the mounting surface 6 Attach the supplied cover over the base of the stand as shown below 7 Attach the cradle to the stand 8 Adjust the angle To the stand receptacle at the bottom of the cradle You can also adjust the angle after installing the main unit into the cradle Notes e Do not install the unit in a location where it may be subjected to extremely high or low temperatures as the cabinet may become deformed or damaged After parking your car the temperature inside the car may raise considerably Therefore cover the cradle and the main unit with a white cloth or remove it from the cradle
16. ymbol of unified polarity type jack Se Placement of the Home Antenna The satellite is located in the south sky Place the antenna as follows for proper reception Outside the house Place the antenna in an area where there are no obstacles within 20 60 degrees facing the southern sky On a flat surface so that it is parallel to the ground When you place it indoors or if there is a building or tree in the direction of the satellite the antenna may not be able to receive the radio wave Depending on where you live you may be able to receive radio waves that are retransmitted by ground repeaters Replacing the Lithium Battery into the Remote Commander Replace the battery when the buttons on the remote commander do not work Remove the old battery and insert a new one 1 Insert a long and thin object into the hole then pull out the lithium battery holder 2 Place the lithium battery with the positive side facing up 3 Insert the battery holder into the remote commander until it clicks Battery life Approx Sony lithium battery CR2025 1 year Notes on lithium battery e Keep the lithium battery out of reach of children Should the battery be swallowed immediately consult a doctor e Wipe the battery with a dry cloth to assure good contact e Be sure to install the battery in the correct polarity position e Do not hold the battery with metallic tweezers as doing so may cause a short
Download Pdf Manuals
Related Search