Sony PEGA-WL100 User's Manual
Contents
1. OK J Cancel J Advanced Setup 9 Select the encryption level in WEP Be sure to select the same encryption level for both your CLIE handheld and the other communication device WirelessLANSetup ProfileName Profile 2 NetworkID SSID Sony Ad WEP 40 64 acters 10 figures Hex Conne 104 128bit 13 characters infr 104 128bit 26 figures Hex OK VC Cancel J Advanced Setup Tip When you select None in WEP you do not need to enter a WEP key In this case skip the next step and go to Step 11 Il Continued on next page 25 10 Enter a WEP key Be sure to enter the same WEP key in both your CLIE handheld and the other communication device For details on WEP key see pages 17 18 WirelessLAN Setup ProfileName Profile 2 NetworkID SSID Sony Ad WEP 40 64bit 5 characters KEY Input 5 characters OK J Cancel Advanced Setup 11 Tap Adhoc in ConnectM ode The Ad hoc mode is selected as the connection type WirelessLAN Setup ProfileName Profile 2 NetworkID SSID Sony Ad WEP 40 64bit 5 characters ConnectMode Infrastructure ch Ich OK J Cancel Advanced Setup 26 12 Tap V of ch below Adhoc and select a channel Be sure to select the same channel for both your CLIE handheld and the other communication device Select a channel from 1 to 11 WirelessLANSetup Pro2. 3 Tap Y in the upper right corner of the screen and select Netw ork The Network screen appears 4 Tap Y of Service and select Wireless LAN Prefer ences Network Service Wireless LAN Details Connect Tip If you have set only one profile go to Step 8 Il Continued on next page 21 5 Tap Details in the lower left corner of the screen The Wireless LAN Setup screen appears Wireless LAN Setup Profile Name w Profile 1 OK Create Edit J Delete 6 Tap V below Profile Name and select the profile name you want to use Wireless LAN Setup Profile Name NewProfile Profile 1 Profile 2 OK Create Edit J Delete 7 Tap OK The Preferences screen appears again 8 Tap Connect at the bottom of the screen Your CLIE handheld begins to connect to a wireless LAN When a connection is established start up the application you like 22 Performing Communications Directly between your CLIE Handheld and Another Device on a Wireless LAN Ad Hoc Mode Your CLIE handheld can communicate directly with another device on a wireless LAN without using a wireless LAN access point The Ad hoc mode settings and communications require network knowledge Basic Settings 1 Insert the Wireless LAN card in Wireless Communication Slot of your CLIE handheld 2 Tap the Prefs icon on the home screen of your CLIE
3. 90 m Outdoor 1000 ft 300 m Supported protocol TCP IP Applied standard IEEE 802 11b Frequency band 2 4 GHz band 1 11 channels ISM band WEP data encryption 128 bit 40 bit Modulation method DS SS in conformity to IEEE 802 11b Operating temperature 41 F 95 F 5 C 35 C Actual range will vary depending on factors such as obstacles between devices magnetic fields around a microwave oven static electricity interference radio wave conditions reception sensitivity or antenna performance or the operating system or software application etc Design and specifications are subject to change without notice 38 Customer Support For the latest support information check our official Sony CLIE Web site Customers in USA Canada and Mexico http www ita sel sony com support clie access Customers in European Countries http www clie link com Customers in Asia Pacific Countries http vaio online sony com clie http www sony net Printed on 100 recycled paper using VOC Volatile Organic Compound free vegetable oil based ink Printed in Japan
4. Cancel to cancel the deletion 3 Tap the Q Home icon The home screen appears Do not modify the settings while the Wireless LAN card is being connected to the wireless LAN access point Il Continued on next page 29 Connecting your CLIE Handheld to Another Device on a Wireless LAN 1 insert the Wireless LAN card in Wireless Communication Slot of your compatible CLIE handheld 2 Tap the Prefs icon on the home screen of your CLIE handheld The Preferences screen appears 3 Tap Y in the upper right corner of the screen and select Netw ork 4 Tap Y of Service and select Wireless LAN Preferences Network w Service Wireless LAN uu Details Connect Tip If you have set only one profile go to Step 8 30 5 Tap Details in the lower left corner of the screen The Wireless LAN Setup screen appears Wireless LAN Setup Profile Name w Profile 1 OK Create Edit j Delete 6 Tap Y below Profile Name and select the profile name you want to use Profile Name OK J Create Edit J Delete 7 Tap OK The Preferences screen appears again 8 Tap Connect at the bottom of the screen Your CLIE handheld begins to connect to a wireless LAN When a connection is established start up the application you like 31 Performing a HotSync Operation via a Network with a Wireless LAN Card This Wireless LAN card can be use
5. Network ID is case sensitive between capital letters and small letters Be careful when entering a Network ID 16 9 Select the encryption level in WEP WEP encryption level is fixed depending on the access point you use Be sure to select the encryption that is used by your access point Wireless LAN Setup i ProfileName NetworkID SSID Sony WEP 40 6 racters 10 figures Hex Conne 104 128bit 13 characters m 104 128bit 26 figures Hex OK Cancel Advanced Setup Tip When you select None in WEP you do not need to enter a WEP key In this case skip the next step and go to Step 11 10 Enter a WEP key The WEP key is fixed depending on the access point you use Be sure to enter the WEP key that is specified by your access point WirelessLAN Setup ProfileName Profile NetworkID SSID Sony WEP 40 64bit 5 characters KEY aaao ConnectMode KEY Input 5 characters OK J Cancel Advanced Setup Il Continued on next page 17 When you select 40 64bit alphanumeric string 5 characters Enter a 5 digit password using alphabet a z numbers 0 9 and symbols When you select 40 64bit hexadecimal notation 10 figures Hex Enter a 10 digit password using alphabet a f and numbers 0 9 When you select 104 128bit alphanumeric string 13 characters Enter a 13 digit password using alphabet a z numbers 0 9 and symb
6. appears 14 4 Tap Y of Service and select Wireless LAN Prefer ences w Network Service Wireless LAN Details Connect 5 Tap Details in the lower left corner of the screen The Wireless LAN Setup screen appears Profile Name w NewProfile OK Create Edit J Delete 6 Tap Create A new input screen of Wireless LAN Setup appears ProfileName NewProfile NetworkID SSID WEP None ConnectMode OK J Cancel advanced Setup Check that Infrastructure is selected highlighted in ConnectModel If it is not selected tap Infrastructure to select it Il Continued on next page 15 Tip Tapping the mark in the upper right corner of the screen shows a brief explanation for the setting 7 Entera profile name in ProfileName Specify a name freely according to the name of the other communication device access point etc WirelessLAN Setup ProfileName Profile NetworkID SSID amn WEP None ConnectMode OK ie Cancel Advanced Setup 8 Enter a network ID in Netw orkID SSID Network ID SSID is fixed on the part of the access point you use Be sure to enter the network ID SSID that is specified by your access point Wireless LAN Setup i ProfileName Profile NetworkID SSID Sony WEP ow None ConnectMode OK Cancel Advanced Setup
7. not modify the settings while the Wireless LAN card is being connected to the wireless LAN access point 19 Advanced Settings Setting a network manually When it is necessary to set a network IP address or DNS address follow the procedure below 1 Tap Advanced Setup in the lower right corner of the Wireless LAN Setup input screen 2 Tap the checkbox of Auto in IP Address or DNS Address and remove the tick The IP Address input screen or the DNS Address input screen appears IP Address O Auto SubnetMask Gateway Address DNS Address Auto PrimaryDNS SecondaryDNS PowerSaveMode X Enable 3 Enter necessary addresses 4 Tap OK when you complete the setting Disabling the power saving mode 1 Tap Advanced Setup in the lower right corner of the Wireless LAN Setup input screen 2 Tap the checkbox of Enable in PowerSaveM ode and remove the tick The power saving mode is disabled Tip When the communication conditions are not good you can disable the power saving mode to maximize the battery power and achieve better communications However it will make the battery life shorter Normally the power saving mode is recommended 20 Connecting your CLIE Handheld to a Wireless LAN 1 Insert the Wireless LAN card in Wireless Communication Slot of your CLIE handheld 2 Tap the Prefs icon on the home screen of your CLIE handheld The Preferences screen appears
8. GS ONY 4 668 080 11 1 Wireless LAN Card Operating Instructions CLI GEAR PEGA WL100 2002 Sony Corporation Owner s Record The model number and serial number are located at the rear of the product Record the model number and the serial number in the space provided below Refer to them whenever you call upon your Sony dealer regarding this product Model Number PEGA WL100 Serial Number For the customers in USA and Canada NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which
9. S 7 handheld LAN access point e To access the Internet through a LAN access point you need to be a subscriber to a telecommunications company and an Internet Service Provider ISP in advance You may need a personal computer to set a wireless LAN For details see the Operating Instructions of your wireless LAN access point Names of Parts Wireless LAN Card F ront LED indicator Blinks slowly while your CLI handheld is connected to an access point etc Blinks rapidly during data transfer Flashing speed varies depending on the amount of data being transferred Does not blink when your CLI handheld is not connected to an access point etc Rear MAC Address This address may be used by your System Administrator Other items included CD ROM 1 Hard case 1 Operating Instructions 1 Warranty card 1 End User s License Agreement 1 Inserting Removing the Wireless LAN Card Inserting the Wireless LAN card in your CLIE handheld Insert the Wireless LAN card in Wireless Communication Slot of the CLIE handheld e Insert the Wireless LAN card straight in Wireless Communication Slot of the CLIE handheld Do not insert the Wireless LAN card in the wrong way Forcing it in the wrong way will damage it and cause a malfunction e You may be unable to use the Wireless LAN card when the remaining power of the battery in the CLIE handheld is low Before using c
10. ase the distance between the device and the CLIE handheld or turn off the power of the device You forget a WEP gt After changing all the settings of the encryption key access point to its factory default setting set the access point again To restore the default settings see the operating instructions of the access point You cannot send or gt Check the settings of the emailing receive email software you are using For details on how to set the emailing software see its operating instructions You cannot perform a gt Check the settings of HotSync HotSync operation For details on how to set HotSync see the operating instructions supplied with your CLIE handheld You cannot browse gt Check the settings of the web browser homepages you are using For details on how to set the web browser see its operating instructions Tip You can view the data of the communication preferences While performing communications using your CLIE handheld in which this Wireless LAN card is inserted show the Network screen of Preferences Select Option on the menu then select View Log 36 Precautions on Use Handling this Wireless LAN Card e Do not subject the card to excessive shock and take care not to drop it to prevent malfunction e Do not use or store this unit in locations subject to extremely high temperature such as in direct sunlight or near a heater excessive dust high humidi
11. cted Before using it make sure you read the regulation leaflet of this product e In some situations or environments the use of the IEEE 802 11b technology might be restricted by the proprietor of the building or responsible representatives of the organization for example on board of airplanes in hospitals or in any other environment where the risk of interference with other devices or services is perceived or identified as harmful e If you are uncertain about the policy applying to the use of IEEE 802 11b technology in a specific organization or environment you are encouraged to first ask for authorization prior to switching it on Consult your physician or the manufacturer of personal medical devices pacemakers hearing aids etc regarding any restrictions on the use of IEEE 802 11b technology 4 Sony SONY CLIE CLI CLIE GEAR GSAS UNIO Jog Dial and Memory Stick are trademarks of Sony Corporation Palm OS and HotSync are registered trademarks of Palm Inc or its subsidiaries Palm Desktop and HotSync logo are trademarks of Palm Inc or its subsidiaries e Microsoft Windows and Windows NT are registered trademarks of Microsoft Corporation in the United States and or other countries e Adobe and Adobe Acrobat Reader are trademarks of Adobe Systems Incorporated e All other names of systems products and services are trademarks of their respective owners In the manual the TM or marks are not specified Befor
12. d in various ways For example you can perform a HotSync operation with a Windows computer via a wireless LAN Follow the procedures below Preparing your computer 1 Click the 5 icon in the Windows task tray bottom right corner of the taskbar and select Netw ork from the shortcut menu 2 Click the icon in the Windows task tray again and select Setup from the shortcut menu The Setup screen is displayed 3 Click the Netw ork tab then click the check box next to the user name for HotSync 4 Click TCP IP Settings and enter a Subnet Mask 5 Click OK 6 Connect your CLIE handheld to your computer and perform a HotSync operation The computer information is transferred to your CLIE handheld When you perform a HotSync operation via a wireless LAN your CLIE handheld identifies the computer based on the information transferred Preparing your CLIE handheld Follow the steps below to set up your CLIE handheld for a HotSync operation via a wireless LAN 1 Select Wireless LAN in Service on the Network screen of Preferences and select a profile name for a HotSync operation on the Wireless LAN details screen For details see the Steps 1 to 6 of Connecting your CLIE Handheld to a Wireless LAN on pages 21 and 22 32 2 Rotate the Jog Dial navigator to select HotSync and press the Jog Dial navigator on the Application Launcher screen The HotSync screen is displayed You can also tap the HotSync icon
13. e using the PEGA WL100 be sure to read the End User Software License Agreement that accompanies it e Copyright laws prohibit reproducing the software or the manual accompanying it in whole or in part or renting the software without the permission of the copyright holder e In no event will SONY be liable for any financial damages or loss of profits including claims made by third parties arising out of the use of the software supplied with this unit e If a problem occurs with this product as a result of defective manufacturing SONY will replace it However SONY bears no other responsibility e The software provided with this unit cannot be used with other units e Please note that due to continued efforts to improve quality the software specifications may be changed without notice e Operation of this unit with software other than that provided is not covered by the warranty Table of Contents Introduction tisse Ne MR Msn ste a 7 Names of Parts Inserting Removing the Wireless LAN Card 310 Installing the Software ccccsesseseeseeesseseeeseeseseseeseseseessstesesesneseeneseenes 12 Performing Communications via a Wireless LAN Access Point Infrastructure Mode dre errant 14 Basic Settings rene es ieran EERE aeaee SREE 14 Advanced Settings ss 20 Connecting your CLI Handheld to a Wireless LAN 21 Performing Communications Directly between your CLI Handheld and Another Device on a Wireless LAN Ad H
14. fileName Profile 2 NetworkID SSID Sony Ad WEP 40 64bit 5 q KE Col Infrastructure amp ch ch 10ch palier fre 13 Tap Advanced Setup in the lower right corner of the screen 14 Tap the checkbox of Auto in IP Address and remove the tick The IP address input screen appears IP Address Q Auto SubnetMask Gateway Address DNS Address Auto PowerSaveMode Enable Ad hoc mode may not be established if Auto is checked The connection works only when both of the PC without DHCP and CLIE handheld select Auto Most of the time user has to enter static IP on CLIE handheld for the Ad hoc mode LI 27 15 Enter an IP address and a sub netmask Enter different IP addresses in your CLIE handheld and the other communication device Enter the same Subnet mask in your CLIE handheld and the other communication device Eg IP address Subnet mask Wireless LAN Setup O Auto IP Address Gateway Address DNS Address PowerSaveMode SubnetMask 255 266 255 M Enable Tip CLI handheld 192 168 0 1 Other device 192 168 0 2 CLI handheld other device 255 255 255 0 User has to find the Subnet mask from the PC that he she wants to connect to The following is referred to find Subnet mask on a PC Windows 98 and Windows ME From Start gt Run gt type in winipcfg gt the IP configuration dialog b
15. handheld The Preferences screen appears 3 Tap Y in the upper right corner of the screen and select Network The Network screen appears 4 Tap Y of Service and select Wireless LAN Prefer ences Network Service Wireless LAN Details Connect Il Continued on next page 23 5 Tap Details in the lower left corner of the screen The Wireless LAN Setup screen appears Profile Name w NewProfile OK Create Edit j Delete 6 Tap Create A new input screen of Wireless LAN Setup appears Wireless LAN Setup i ProfileName NewProfile NetworkID SSID amn WEP None ConnectMMode OK Cancel Advanced Setup Tip Tapping the G mark in the upper right corner of the screen shows a brief explanation for the setting 7 Entera profile name in ProfileName Specify a name freely according to the name of the other communication device access point etc WirelessLAN Setup ProfileName Profile NetworkID SSID ann WEP None ConnectMode 24 OK J Cancel Advanced Setup 8 Enter a network ID in NetworklD SSID Specify an alphanumeric string freely The same network ID SSID needs to be entered in both your CLIE handheld and the other communication device Wireless LAN Setup GJ ProfileName NetworkID SSID Sony Ad WEP None ConnectMode
16. harge the battery fully Insert the Wireless LAN card all the way into the slot until it fully mates with the t connector 10 Removing the Wireless LAN card from your CLIE handheld After use terminate communications Then pull the wireless LAN card up straight When using this Wireless LAN card with a Flip amp Rotate style CLIE handheld Do not rotate the display when the wireless LAN card is inserted in the Wireless Commnunication Slot of the CLIE handheld This may press the display panel against the Wireless LAN card and cause a malfunction During communication do not remove the Wireless LAN card or subject the CLIE handheld to excessive shock 11 Installing the Software When you try to perform wireless LAN communications for the first time after inserting the Wireless LAN card in your CLIE handheld you need to install the Wireless LAN utility in your CLIE handheld You can install the Wireless LAN utility by using the supplied CD ROM Before installation it is necessary to have Palm Desktop for CLIE installed and to perform a HotSync operation Connect the CLIE handheld to a Windows computer using a cradle etc For details on how to connect the CLIE handheld to the computer see the Operating Instructions of your CLIE handheld 1 Perform a soft reset on your CLIE handheld For details on how to perform a soft reset see the Operating Instructions of your CLIE handheld 2 Insert the supplied CD ROM i
17. his will increase the power consumption Be careful of the remaining battery power e The channels of the access point are not set at 1 11 gt Change the channel setting of the access point You cannot access the Internet The access point you are using is not configured for internet access gt Connect the access point to the Internet following the operating instructions of the access point e There is a mistake in the Network settings gt Ask your System Administrator about the settings The data transfer rate is slow e Some other access points are interfering with communication gt Change the channel number of the access point you are using For details on how to change the setting see the Operating Instructions of your access point The access point is being heavily used gt Wait a while and try access again ll Continued on next page 35 Symptom Cause Remedy The data transfer rate is There is an obstacle that could block off slow radio waves e g metal plate concrete block between your CLIE handheld and the access point gt Move your CLIE handheld and or the access point to a different place gt Disable the power saving mode This will increase the power consumption Be careful of the remaining battery power There is a device operating at the 2 4 GHz band of frequencies microwave oven Bluetooth enabled device etc around the CLIE handheld gt Incre
18. line sony com clie If the problem persists contact the Sony dealer where you purchased this product or a Sony service representative serving your area Symptom Cause Remedy Your CLIE handheld e The Wireless LAN card is not installed does not recognize this correctly in your CLIE handheld Wireless LAN card gt Insert the Wireless LAN card into Although connection Wireless Communication Slot of your has started the LED compatible CLIE handheld in the indicator on the correct way until it fully mates with the Wireless LAN card connector does not flash e A service other than Wireless LAN is selected in the Network of Preferences gt Select Wireless LAN in Service You cannot connect your CLIE handheld to an access point e A wrong profile is selected gt Check the Profile Name you have selected on the Wireless LAN Setup screen e The settings for communications are not correct gt Check the settings of Network ID WEP key etc 34 Symptom Cause Remedy You cannot connect your CLIE handheld to an access point e Your CLIE handheld and the access point are placed too far apart gt Decrease the distance between them e There is an obstacle that could block off radio waves e g metal plate concrete block between your CLIE handheld and the access point _ gt Move your CLIE handheld and or the access point to different places gt Disable the power saving mode T
19. n the CD ROM drive of your Windows computer The installer starts and the initial screen appears Tip If the installer does not start automatically double click setup setup exe which can be found in the CD ROM 3 Proceed with the installation following the installer s instructions On the user name selection screen select a user s name If you want to use more than one CLIE handheld you need to install this utility in each CLIE handheld 12 4 Click Done when the installer closing screen appears Your computer is ready to install the Wireless LAN utility to your CLIE handheld In the next step you will perform a HotSync operation to carry out the installation 5 Click the 9 icon on the task tray that is located in the lower right corner of the Windows display on your computer Check that Local USB is ticked in the shortcut menu on the display Tip If you cannot find the 6 icon on the task tray click Programs AIl Programs in Windows XP Sony Handheld and then HotSync Manager to start up the HotSync manager from the Start menu 6 Execute a local HotSync operation on your CLIE handheld The Wireless LAN utility is installed into your CLIE handheld Part of this software application extends into the system of CLIE handheld Therefore it cannot be uninstalled After you perform a hard reset Be sure to reinstall this utility After a hard reset normally the backup data in a personal comp
20. nce and 2 this device must accept any interference including interference that may cause undesired operation of the device L utilisation de ce dispositif est autoris e seulement aux conditions suivantes 1 il ne doit pas produire de brouillage et 2 l utilisateur du dispositif doit tre pr t accepter tout brouillage radio lectrique recu m me si ce brouillage est susceptible de compromettre le fonctionnement du dispositif LT continued on next 3 To prevent radio interference to the licensed service this device is intended to be operated indoors and away from windows to provide maximum shielding Equipment or its transmit antenna that is installed outdoors is subject to licensing Pour emp cher que cet appareil cause du brouillage au service faisant l objet d une licence il doit tre utilis l int rieur et devrait tre plac loin des fen tres afin de fournir un cran de blindage maximal Si le mat riel ou son antenne d mission est install l ext rieur il doit faire l objet d une licence This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada For the customers in European countries Sony hereby declares that this product is in compliance with the essential requirements and other relevant provisions of European Directive 1999 5 EC In some countries the use of the Wireless LAN Card is restri
21. oc Mode Basic Settings ccccscsesscseeseesessesseeseeseseseesesneseesesnessseseesesneseenesneneas Connecting your CLI Handheld to Another Device on a Wireless LAN aactvuniiicimntitinniiatdannes 30 Performing a HotSync Operation via a Network with a Wireless LAN Card nn MR Rens nues ete None 32 Troubleshooting cecccccscesesseseessesessesesseseesesseseeseseseeseaeseessseeseseseessaneseenes 34 Pr cautions on Uses snc gies NT ets 37 Sp cifications sser MER Reste 38 Introduction This product is a Wireless LAN Card for the Sony Personal Entertainment Organizer mentioned as CLIE handheld after this of the Palm OS 5 ver5 0 This product complies with IEEE 802 11b and allows you to access the Internet wirelessly in locations where there is a Wi Fi certified wireless LAN access point Wi Fi certified Performing a HotSync operation You can perform a HotSync operation via a network synchronize data wirelessly between your CLIE handheld and a personal computer For details on HotSync operation see the Operating Instructions of your CLIE handheld PEGA WL100 and CLIE handheld Personal computer LAN access point Il Continued on next page 7 Accessing the Internet You can access the Internet from your CLIE handheld in which this Wireless LAN card is inserted through a LAN access point and enjoy browsing various websites or sending receiving email a Internet PEGA WL100 mr ES and CLIE AS
22. ols When you select 104 128bit hexadecimal notation 26 figures Hex Enter a 26 digit password using alphabet a f and numbers 0 9 WEP key distinguishes between capital letters and small letters Be careful when entering a WEP key Tips e WEP key is the function that encrypts data that are to be sent by radio waves Depending on the manufacturer the above WEP keys may be assigned a different name 11 Tap OK The basic settings are completed by the profile name you set in Step 7 12 Tap the Q Home icon on your CLI handheld The home screen appears 18 Modifying the settings 1 Tap the Prefs icon on the home screen of your CLIE handheld The Preferences screen appears 2 Tap V in the upper right corner of the screen and select Netw ork The Network screen appears 3 Tap Y of Service and select Wireless LAN 4 Tap Details in the lower left corner of the screen The Wireless LAN Setup screen appears 5 Tap Y below ProfileName and select the profile name you want to modify 6 Tap Edit at the bottom of the screen The Wireless LAN Setup input screen appears 7 Modify the settings 8 Tap OK 9 Tap the Q Home icon The home screen appears Deleting the profile you have set 1 In Step 6 of Modifying the settings above tap Delete at the bottom of the screen The selected profile is deleted 2 Tap OK 3 Tap the Q Home icon The home screen appears Do
23. ox appears gt check the IP address and Subnet mask Windows 2000 and Windows XP From Start gt Run gt type in cmd gt type ipconfig all check the IP address and Subnet mask Enter a gateway address if necessary When it is necessary to enter a DNS address tap and tick the checkbox of Auto in DNS Address before entering the DNS address 16 Tap OK The Wireless LAN Setup screen appears 17 Tap OK The settings are completed in the profile name you set in Step 7 18 Tap the 28 Q Home icon on your CLI handheld The home screen appears Modifying the settings 1 Tap the Prefs icon on the home screen of your CLIE handheld The Preferences screen appears 2 Tap Y in the upper right corner of the screen and select Netw ork The Network screen appears 3 Tap Y of Service and select Wireless LAN 4 Tap Details in the lower left corner of the screen The Wireless LAN Setup screen appears 5 Tap Y below ProfileName and select the profile name you want to modify 6 Tap Edit at the bottom of the screen The Wireless LAN Setup input screen appears 7 Modify the settings 8 Tap OK 9 Tap the Q Home icon The home screen appears Deleting the profile you have set 1 In Step 6 of Modifying the settings above tap Delete at the bottom of the screen The Delete Profile confirmation dialog window appears 2 Tap OK to confirm deletion or
24. the receiver is connected Consult the dealer or an experienced radio TV technician for help FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Declaration of Conformity Trade Name SONY Model No PEGA WL100 Responsible Party Sony Electronics Inc Address 1 Sony Drive Park Ridge NJ 07656 USA Telephone No 201 930 6972 This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC Radiation Exposure Statement This transmitter complies with FCC radiation exposure limits set forth for an uncontrolled environment To comply with the FCC RF exposure compliance requirements no change to the antenna or the device is permitted Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user In addition this transmitter must not be co located or operating in conjunction with any other antenna or transmitter The term IC before the radio certification number only signifies that Industry Canada technical specifications were met Operation is subject to the following two conditions 1 this device may not cause interfere
25. to display the HotSync screen 3 Tap the Menu icon and tap Primary PC Setup from the Option menu 4 Check that correct data is entered in Primary PC Address and Subnet Mask optional and tap OK 5 Tap the Menu icon and tap Modem Sync Prefes from the Option menu 6 Tap Network and tap OK 7 When the HotSync screen appears tap Modem and then tap Select Service 8 Tap Y of Service select Wireless LAN and tap Done Tip It is unnecessary to enter a telephone number in Enter phone It is also necessary to select Wireless LAN in Service on the Network screen of the Preferences that can be started from the home screen Performing a HotSync operation When you finish the preparation of your CLIE handheld and your computer tap the HotSync icon on the HotSync screen Your CLIE handheld automatically connects to the network and begins a HotSync operation When communication is not possible Following the above Step 3 erase the Primary PC Name 33 Troubleshooting If any problem occurs for example if communication is not possible or if the unit does not operate normally please check the points listed in this troubleshooting guide Visit Sony CLIE support website Customers in USA Canada and Mexico http www ita sel sony com support clie access Customers in European Countries http www clie link com Customers in Asia Pacific Countries http vaio on
26. ty vibrations poor ventilation It may cause a malfunction e Do not use the card in a shaky unstable place e Do not put a metal object such as a metal clip etc inside the card e When inserting the card in the CLIE handheld take care not to force it in the wrong way It may cause a malfunction e When there is a device operating at the 2 4 GHz band of frequencies around the CLIE handheld the card and the CLIE handheld may not work correctly Condensation Condensation is a phenomenon that occurs when moisture in the air becomes water drops when it contacts a metal plate etc Condensation may occur on the surface or inside of the Wireless LAN Card on occasions when you quickly move it from a cold place to a warm place when you turn on the heater in the room on a cold winter morning Using the Wireless LAN Card with condensation on it may cause a malfunction If condensation occurs on the Wireless LAN Card leave it without turning on the power of the CLIE handheld until the condensation disappears 37 Specifications Power source Powered by CLIE handheld Power consumption When transmitting Approx 560 920 mW typ Idle Approx 90 mW typ At the default setting Note The Wireless LAN card consumes no electricity when the LED indicator is off Dimensions Approx 1 11 16 x 2 1 4 x 1 4 in width length thickness 42 8 x 55 4 x 5 9 mm Mass Approx 0 5 oz 14 g Maximum communication range Indoor 300 ft
27. uter is automatically restored to your CLIE handheld through a HotSync operation However this utility restores only the setting file when a HotSync operation is performed and it does not restore the utility itself Therefore it is necessary to reinstall this utility after a hard reset 13 Performing Communications via a Wireless LAN Access Point Infrastructure Mode You can wirelessly access the Internet or perform communications with other communication device through a wireless LAN access point Basic Settings Before setting You first need to input a couple of values to set the wireless LAN access point you use Check the following values in advance NetworkID SSID It is also called ESS ID or Network Name WEP Wired Equivalent Privacy It is also called Encryption For details ask your System Administrator When you have a wireless LAN access point for your personal use refer to the operating instructions of the wireless LAN access point The Wireless LAN card uses the 1 11 channels 2 4 GHz band of frequencies If your access point uses the 12 14 channels it is impossible to perform communications using the Wireless LAN card 1 Insert the Wireless LAN card in Wireless Communication Slot of your CLIE handheld 2 Tap the Prefs icon on the home screen of your CLIE handheld The Preferences screen appears 3 Tap Y in the upper right corner of the screen and select Netw ork The Network screen
Download Pdf Manuals
Related Search