Snap-On 870011 User's Manual
Contents
1. The clipped head nailer is equipped with a trigger lock to prevent operation of the tool when not actively being used To lock trigger move trigger lock lever up to the locked position To unlock trig ger in preparation for use move the trigger lock lever down to the unlocked position Figure 7 Figure 7 CHANGING DIRECTION OF EXHAUST AIR The direction of exhaust air on the air nailer can be 0 directed 360 degrees by placing hand on exhaust cover and turning See Figure 8 Figure 8 CLEARING JAMS Typically jams are caused when a fastener or a fastener fragment becomes wedged between the driver blade and nail guide Using the wrong fastener can also cause jams TO CLEAR A JAM 1 Disconnect the air supply and remove the fastener strip Leave the pusher assembly open 2 Loosen hex screws from back of magazine and pull magazine back See Figure 9 Figure 9 3 Remove jammed fastener 4 Slide magazine back in position and refasten hex screws Figure 10 Figure 10 MAINTENANCE STORAGE OF NAILS Always handle nail strips and their box very carefully If the nail strips have been mis handled they may be out of shape or have breaks in the connecting strips This will cause the nails to feed poorly and possibly result in misfiring or jams in the air nailer Avoid storing nails in a very humid or hot environment or place in direct sunlight OVERALL MAINTENANCE OF AIR NAILER2. 4 WARNING Always disconnect the air hose from clipped head nail er before attempting any type of maintenance or visual inspection of tool 16 Always visually inspect clipped head nailer before every use Check on the overall condition and for any loose screws Tighten any screws that have come loose See Figure 11 Visually inspect the work piece contact and trigger to ensure there is free movement See Figure 12 When the tool is not going to be used for an extended period wipe off all dust and debris that have collected on it Tighten all loose screws Lubricate the firing mechanism with pneumatic tool oil See page 9 for Lubrication Figure 11 Store the clipped head nailer in a safe loca tion or in suitable carrying case It is recom mended that the air nailer be secured in a locked location to prevent unauthorized usage Avoid exposure to direct sunlight and or locations with high humidity and heat A WARNING Remove the clipped head nailer from use and schedule to have it repaired at an authorized repair facility if the work piece contact is binding or not moving freely Do not attempt to repair the clipped head nail er Failure to comply can result in malfunction of the tool and severe injury to the operator or any bystanders 17 MANDATORY MAINTENANCE A WARNING All maintenance and repairs should be performed by an authorized repair facility Call 1 888 278 8092 to obta
3. Driver MUST move up N Select Contact Actuation Operation Holding nailer away from work piece pull trigger The tool MUST NOT operate While still pulling trigger press the nailer against work piece The tool MUST operate oo If Steps 1 through 7 function properly prepare the tool for use Select opera tion mode and load fasteners 9 Set the required depth of drive 10 Repeat these steps daily Test again if the nailer is dropped jammed etc USING THE AIR NAILER To drive a nail place the work piece contact of the clipped head nailer against the work piece and pull the trigger See Figure 6 To avoid any unexpected nailings perform the operation as follows 1 Avoid placing the work piece contact against the work piece with excessive force 2 Pull the trigger fully and hold it in the fired position for 1 to 2 seconds before releasing the trigger This will give the clipped head nailer time to completely expend the previous nail and build enough pressure for the next nail Figure 6 14 A WARNING po NOT hold the trigger in a half pulled position This could cause an unexpected nailing to occur if the work piece contact is permit ted to re contact the work piece Failure to comply could result in damage to work piece LOCKING AND UNLOCKING THE TRIGGER 4 WARNING Always move lever to the locked position immediately after using the nailer to prevent unintended firing of fastener
4. SPECIFICATIONS MODEL NUMBER 870011 70 120 PSIG 5 0 8 5 kg cm 2G 2 50 8 mm 3 1 2 88 9 mm AIR PRESSURE NAIL LENGTH COLLATION ANGLE 30 34 1 4 6 5 mm 7 2 LBS 3 2 KG MINIMUM HOSE DIAMETER NET WEIGHT 1 YEAR LIMITED WARRANTY Express and Exclusive Limited Warranty to Original Retail Buyer Alltrade Tools LLC hereinafter Alltrade expressly warrants to the original retail purchaser of the accompanying SNAP ON portable air tool and no one else all parts of the product except those parts referred to below which are specifically excluded from such warranty see Exclusions to be free from defects in materials and workmanship for a period of one year from the original date of purchase The date of purchase shall be the date of shipment to the original purchaser or the date the original purchaser took possession custody or control of the product whichever occurred first This warranty shall be null and void if the product or any component thereof is modified or altered This warranty does not apply to any other product and or component thereof manufactured or distributed by Alltrade and does not apply to products and or components thereof designed manufactured and or assembled by others for which Alltrade makes no warranties whatsoever THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF WARRANTY PERFORM ANCE By purchasing this product purchaser expressly acknowle
5. air coupler can allow the clipped head nailer to discharge a fastener while the tool is dis connected from the power source Failure to comply with this warning can result in serious or permanent injury or even death to the operator or to bystanders When the air hose is disconnected the pressure reservoir in the air nailer will discharge removing any built up air inside the tool REQUIRED DAILY PREPARATION The following steps should be performed on a daily basis to ensure the clipped head nailer is operating correctly 1 Disconnect air supply from nailer and remove fastener strip 2 Check all screws nuts and pins and ensure all are tight 3 Press the pusher release button and slide back the pusher assembly Overriding the dry fire lockout Press the work piece contact against a work piece ensuring smooth movement 4 With work piece contact against the work piece pull trigger The trigger must operate smoothly 5 Connect air supply and set regulator for 70 psi DO NOT load a fastener strip 13 6 Select Single Sequential Actuation Operation Check for leaks Without pulling the trigger press the work piece contact against the work piece The tool MUST NOT operate Holding the tool away from the work piece pull trigger and hold for 5 seconds The tool MUST NOT operate Repeat steps several times Without pulling trigger press nailer against work piece and pull trigger The tool MUST operate Release trigger
6. before it happens and by observing appropriate safety rules and procedures as outlined in this manual Basic safety precautions are outlined in the SAFETY portion of this manual and throughout text in this manual where a potential hazard might occur Hazards that MUST be avoided to prevent serious injury follow headers marked DANGER or WARNING These same precautions are placed as labels on the tool itself NEVER use this nailer for applications that are NOT specified in this manual SAFETY WARNINGS AND PRECAUTIONS 4 DANGER Do not operate clipped head nailer anywhere fastener may contact hidden electrical wiring Contact with a live wire will make all metal parts of the clipped head nailer live This can result in severe electrical shock severe burns or death to the operator Contact a qualified electrical contractor to ensure a safe working environment exists Be aware of conduits or gas pipes Striking a gas pipe could result in an explo sion causing serious injuries or even death to the operator or bystanders Be aware of what is behind the work piece A fastener could travel through the work piece and out the other side striking a bystander resulting in serious injury or even death Do not operate the clipped head nailer in the presence of flammable liquids such as gasoline thinner paint or adhesives gases or dust Sparks created by the tool can cause flammable materials to ignite or explode Failure to compl
7. the air nailer Check for air leaks LUBRICATION To ensure maximum performance it is recommended to install an air set oiler reg ulator and air filter as close as possible to the air nailer Adjust the oiler so that approximately one drop of oil will be released for every 50 nails If an air set is not used or is unavailable oil the tool using pneumatic tool oil by plac ing 2 or 3 drops into the air inlet This should be done before and after use For proper lubrication the tool must be fired several times after the oil is introduced to the filter OPERATING THE CLIPPED HEAD NAILER A WARNING Always use hearing protection to protect your ears against INE hearing loss due to exhaust noise Always wear proper safe ty glasses to prevent injuries to the eyes from fragments of the work piece defective nails or other debris caused by using the clipped head nailer All safety glasses must have side shields and should conform to the requirements of the American National Standards Institute ANSI 287 1 Failure to comply with this warning could lead to serious or permanent damage to the ears as well as serious damage or permanent blindness in the eyes Always disconnect the air hose before making adjustments or checking the functionality of the air nailer SELECT TRIGGER ACTUATION MODE The clipped head nailer is equipped with a selectable trigger This allows the selec tion of Single Sequential Actuation Mode or Con
8. FOR CUSTOMER SERVICE PARA EL SERVICIO PARA EL CONSUMIDOR 1 888 278 8092 Printed in Taiwan ANAP D SNAP ON9 IS A TRADEMARK LICENSED BY SNAP ON CORP U S A WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT CONSUMER INQUIRES SHOULD BE DIRECTED TO COPYRIGHT 2007 ALLTRADE TOOLS LLC 1431 VIA PLATA LONG BEACH CA 90810 1462 USA 870011 Clipped Head Air Nailer Rev 10 4 07 MODEL 870011 CLIPPED HEAD FRAMING NAILER INSTRUCTION M ANUAL THS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY OPERATION MAINTENANCE AND STORAGE OF THS PRODUCT BEFORE USE READ CAREFULLY AND UNDERSTAND ALL CAUTIONS WARNINGS INSTRUCTIONS AND PRODUCT LABELS FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL IN URY AND OR PROPERTY DAMAGE IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WTH YOUR SNAP ON PRODUCT DO NOT RETURN THS PRODUCT TO THE STORE PLEASE CALL OUR CUSTOMER SERVICE DEPARTMENT AT 1 888 278 8092 BEFORE YOU CALL HAVE THE FOLLOWING INFORMATION AVAILABLE MODEL No DATE PURCHASED AND STORE LOCATION TABLE OF CONTENTS CONGRATULATIONS CONGRATULATIONS 0 ccc ccc ccc suus 2 Thanks for choosing this product Our aim is to provide you with the highest quality prod GENERAL SAFETY RULES suu 2 ucts and we want you to be totally satisfied with your product and our Customer Service If any help or advice is needed please contact us at 1 888 278 8092 When properly RECOGNIZE SAFETY S
9. INSTRUCTIONS Read and understand tool labels safety warnings and precautions in this manual before operating the tool Failure to follow WARNINGS could result in serious injury or even death to the operator or bystanders 7 WEAR APPROVED EYE PROTECTION Safety glasses must conform to the requirements of American National Standards Institute ANSI Z87 1 and provide protection against flying particles from both front and side WEAR HEARING PROTECTORS Hearing protectors should be worn to protect the ears from loud exhaust noise produced by the air tools bustible gases and any other bottled gas to operate air tools Using these other sources can cause the air tool to explode NEVER POINT THE AIR NAILER AT YOURSELF OR OTHERS Fasteners are under extreme pressure and can cause severe injury or even death if misused a 5 USE ONLY CLEAN DRY COMPRESSED AIR Never use oxygen com agp DO NOT EXCEED 120 psi 8 43 kg cm G Using excessive pressure i from the power source can cause the clipped head nailer to explode resulting in severe injury or even death to the operator or bystanders IMPORTANT INFORM ATION ABOUT THIS M ANUAL Improper maintenance and operation are responsible for the majority of accidents involving clipped head nailers The largest portion of these could be prevented by recognizing the basic safety rules and precautions Most accidents can be avoided if the operator recognizes a potentially hazardous situation
10. LY OR INDIRECTLY ANY BREACH OR PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND OR ITS REPRE SENTATIVE S AND PURCHASER AND WARRANTY HEREUNDER AND OR THE EXISTENCE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF ANY ITEM S SOLD HEREUNDER EVEN IF ALLTRADE AND OR ITS REPRESENTA TIVE S HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES IN NO EVENT WHETHER BECAUSE OF A BREACH OF CONTRACT WARRANTY TORT INCLUDING NEGLIGENCE OR OTHERWISE SHALL ALLTRADE S AND OR ITS REPRESENTATIVE S LIABILITY EXCEED THE PRICE OF THE PRODUCT All LIA BILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIODS SPECIFIED ABOVE LIMITATIONS ON WARRANTY DISCLAIMERS Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusion or limitation of the incidental or consequen tial damages so part or all of the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state If your product is not covered by this warranty please call our Customer Service Department at 1 888 278 8092 for general repair information and charges and the location of your nearest authorized service facility 28
11. ON OF ALLTRADE AND OR ITS REPRESENTATIVE S OR THE BUYER ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND OR ITS REPRESENTATIVES PURCHASER KNOWINGLY AND WILLINGLY 27 WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS CLAIMS AND OR CAUSE OF ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE NO WARRANTY ORAL OR WRITTEN OTHER THAN THE WARRANTY LISTED HEREIN IS MADE WITH REGARD TO THIS PRODUCT ALL WARRANTIES AND OR IMPLIED WARRANTIES GUARANTIES AND OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANU FACTURE PURCHASE USE AND OR OPERATION OF THE PRODUCT OR ANY COM PONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AND OR REPRESENTATION WRITTEN OR ORAL ARISES BY OPERATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSION OF ALLTRADE AND OR ITS REPRESENTATIVES PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS CLAIMS AND OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCLUSIVE REMEDY IS AS STATED ON PRECEDING PAGES LIMITATIONS OF LIABILITY IN NO EVENT SHALL ALLTRADE AND OR ITS REPRESENTATIVE S BE LIABLE FOR INDIRECT INCIDENTAL SPECIAL AND OR CONSEQUENTIAL DAMAGES OF ANY KIND ARISING OUT OF OR RELATED TO DIRECT
12. YMBOLS WORDS AND LABELS 2 3 cared for this product will give you many years of satisfaction IMPORTANT INFORMATION ABOUT THIS MANUAL 4 SAFETY WARNINGS AND PRECAUTIONS 0005 4 7 GENERAL SAFETY RULES FUNCTIONAL DESCRIPTION 0000 cc cece Ke 7 9 COM PONENT INSTALLATION LAA AD T ERED PD EE De SO ROO M A 8 9 A WARNING READ AND FOLLOW ALL INSTRUCTIONS Failure to fol OPERATING THE CLIPPED HEAD NAILER ou isses n 9 13 low all instructions in this manual may result in severe personal injury or death SELECT TRIGGER ACTUATION MODE 00 eee 9 11 Keep this manual and refer to it for Safety Instructions Operating Procedures ADJUSTING DEPTH OF NAILING 0 0cccc eee e cues 11 12 and Warranty USING THE HOOK meri Pra bee x RU s 12 SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE LOADING NAILS INTO THE AIR NAILER 08 12 USING THE NO MAR NOSEPIECE sese 13 RECOGNIZE SAFETY SYMBOLS WORDS AND LABELS Peale POET ARA satu etat tavta dui The safety instructions provided in this manual are not intended to cover all possible USING THE AIR NAILER aaa 14 16 conditions and practices that may occur when operating maintaining and cleaning LOCKING AND UNLOCKING THE TRIGGER 05 15 power tools CHANGING DIRECTION OF EXHAUST AIR 1 0 seer ee 15 Always use common sense and pay particular attention to all the DANGER CLEARING JAMS aaa 16 WARNING CAUTION and NOTE state
13. aster operating speeds POSSIBLE CAUSE Ensure proper air pres sure is being used Inspect for worn driver blade Inspect piston O ring for wear or damage Check air pressure Ensure correct nails are being used Inspect nail feeder mechanism Ribbon spring weakened or damaged Piston O ring damaged or worn Nail feeder worn or damaged Ensure correct nails are being used Inspect for worn driver blade Nail feeder worn or damaged Check inside diameter of air hose 19 SOLUTION Increase air pressure Do not exceed 120 psig 8 3 bars 8 5 kg cm Contact Customer Service Reduce air pressure Use ONLY recommend ed nails Clean and lubricate nail feeder Replace ribbon spring Use recommended pneumatic tool oil Contact Customer Service Replace nail feeder Use ONLY recommend ed nails Contact Customer Service Replace nail feeder Switch to air hose with larger inside diameter PARTS DIAGRAM PARTS DIAGRAM PARTS LIST ITEM NO PART NO DESCRIPTION a 2 I 2 2 2 ea EE ERN EX KE ES EX KE EN Kx E 21 ITEM NO PART NO DESCRIPTION ITEM NO PART NO DESCRIPTION I s s s s s s T I I i I I I n Z 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 4 5 6 T 8 9 0 1 2 3 4 5 6 7 8 9 40 41 42 43 4 45 46 47 48 49 ITEM NO PART NO a NN T NN xx lt a DESCRIPTION
14. ation Selector up to the Contact Sequential Actuation TTT 3 Release Actuation Selector ensuring locking tab is fully seated in the slot Figure 2 A WARNING Always disconnect the clipped head nailer before mak ing any adjustments to the nail depth setting USING THE HOOK A CAUTION Ensure selector has locked into position Ensure actuation process is fully understood before attempting to use clipped head nailer TO USE THE CLIPPED HEAD NAILER IN CONTACT ACTUATION MODE 1 Firmly grip clipped head nailer handle 2 Pull and hold the clipped head nailer trigger 3 Push clipped head nailer against work piece compressing work piece contact 4 The clipped head nailer will drive nail upon contact The clipped head nailer will recoil away from the work piece as nail is driven ADJUSTING DEPTH OF NAILING Always disconnect the air hose before hanging the clipped head nailer with the hook NEVER hookthe clipped head nailer in a high location or on an unstable platform LOADING NAILS INTO THE AIR NAILER Always disconnect the air hose from the clipped head nailer before adding or removing nails NEVER use deformed nails or nail strip Failure to observe this precaution can result in poor nail feeding and or jams in the feeding mechanism 4 WARNING Be aware of material thickness when using nailer A pro truding nail may cause injury Adjust the depth of nailing by loosenin
15. be used to limit air pressure where l ai All air compressors must comply with the requirements of ANSI air supply pressure exceeds the tool s rated operating pressure Do not carry the clipped head nailer with a finger on the trigger This could lead to an accidental discharge of the clipped head nailer Do not press the trig ger of the clipped head nailer unless it is pressed firmly against the work piece Do not point the clipped head nailer at yourself or in the direction of another person Failure to comply with this warning could result in serious injury or even death to the operator or other bystanders Do not tamper with the work piece contact The work piece contact prevents accidental discharge of the clipped head nailer and should never be removed or compromised in any way Failure to comply with this warning could result in serious injury or even death to the operator or other bystanders Always disconnect air hose and remove any remaining nails 1 When clipped head nailer is left unattended 2 Before performing any maintenance or repair on the clipped head nailer 3 Before attempting to clear a jam in the clipped head nailer 4 Before moving the clipped head nailer to a new location Always check the overall condition of the clipped head nailer before using Check for and tighten any loose screws Ensure all safety systems are in work ing condition before using the clipped head nailer The clipped head nailer must not operate
16. dges and agrees that their sole and exclusive remedy under this warranty shall be strictly limited to the repair or replacement of any covered nonconforming items or parts thereof provid ed that any such nonconforming item and or part is promptly returned to an author ized Service Center within the applicable warranty period with a written request by purchaser to repair and or replace the nonconforming item and or part We recom mend that you keep the original product packaging in the event you need to ship the unit We suggest the package be insured against loss or in transit damage When sending your product include your name address phone number e mail address dated proof of purchase or copy and a statement about the nature of the problem Warranty coverage is conditioned upon purchaser furnishing Alltrade with adequate written proof that they are the original purchaser and of the original purchase date Parts returned freight prepaid and insured will be inspected and at Alltrade s option repaired and or replaced free of charge if it is found to be defective and sub ject to warranty Alltrade retains the sole discretion to determine whether any item or part is nonconforming and if so whether the item and or part will be repaired and or replaced If the unit is repaired new or reconditioned replacement parts may be used If Alltrade chooses to replace the product it may replace it with a new or reconditioned of the same or comparable de
17. ep it ready for the next job All maintenance and repairs should be performed by an authorized repair facility Call 1 888 278 8092 to obtain a list of repair facilities in your area or to make arrangements to return the tool for service FUNCTIONAL DESCRIPTION CONTROLS AND COMPONENTS 1 Exhaust Cover 9 Magazine Inlet 2 Trigger Lock 10 Nail Stop 3 Trigger ACCESSORIES 4 Spring Lever 11 Safety Glasses 5 No mar Nosepiece 12 Lubricant 6 Pusher 13 Hex Wrenches 2 7 Air Inlet 8 Hanging Hook COMPONENT INSTALLATION 4 WARNING Never use a non relieving air coupler with the clipped head nailer Always use couplers that release any built up charge in the clipped head nailer s firing mechanism A non relieving air coupler can allow the clipped head nailer to discharge a fastener while the tool is disconnected from the power source Failure to comply with this warning can result in serious or per manent injury or even death to the operator or to bystanders When selecting an air compressor it must comply with the requirements of the American National Safety Institute ANSI B19 3 Choose an air compressor that can supply more than the required air pressure to ensure optimum efficiency Always use clean dry compressed air with a maximum pressure of 200 psi Use a pressure regulator and set the pressure between 70 120 PSIG 5 0 8 5 kg cm 2G Before each use check the pressure regulator to ensu
18. g the two hex nuts figure 3 Move nosepiece down for a shallow er nail depth or up for a deeper nail depth Once nosepiece is adjusted tighten hex screws To increase the depth of the nails when the nosepiece is already set to its lowest setting increase the air pressure To decrease the depth of nails when the nosepiece is already set to its highest setting To load nails in clipped head nailer slide nails through magazine inlet in back of mag azine Pull pusher back until it is behind nail strip then release pusher Figure 4 decrease the air pressure Figure 3 11 To remove nails from clipped head nailer pull slightly back on pusher and depress spring lever Figure 4 Allow pusher to pass over nail strip and move strip to back of magazine Depress the nail stop allowing nail strip to be removed from magazine inlet USING THE NO MAR NOSEPIECE A WARNING Always disconnect the air hose before attaching the no mar nosepiece In order to prevent the surface of the work piece from being scratched or damaged use the no mar nose piece Install no mar nosepiece by pressing it into place on the nose frame See Figure 5 Store the no mar nosepiece in place when not being used Figure 5 A WARNING Never use a non relieving air coupler with the clipped head nailer Always use couplers that release any built up charge in the clipped head nailer s firing mechanism A non relieving
19. ht damage Parts damaged or worn by operation in dusty environments are not warranted Failure to follow recommended operating and maintenance procedures also voids warranty DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING ACCIDENT ABUSE NEGLIGENCE FAILURE TO FOLLOW INSTRUCTIONS UNAUTHORIZED REPAIRS OR ALTERATIONS DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES OR OTHER CAUSES UNRELATED TO PROBLEMS WITH MATERIAL OR WORKM ANSHIP ARE NOT COVERED BY THIS WARRANTY Alltrade will not be liable for the following labor charges loss or damage resulting from improper operation maintenance or repairs made by other persons pre deliv ery services such as assembly oil and lubricants and adjustment maintenance services that are normally required to maintain the product The use of other than genuine Snap On Repair Parts will VOID the warranty WARRANTY DISCLAIMERS EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES GUAR ANTIES AND OR REPRESENTATIONS EXCEPT FOR THE LIMITED WARRANTY PROVIDED HEREIN ALL OTHER EXPRESS WARRANTIES GUARANTIES AND OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AND OR REPRESENTATION WRITTEN OR ORAL ARISES BY OPERATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSI
20. if only the trigger is pulled or if only the work piece contact is pressed against the work piece The clipped head nailer must only be used if both the trigger and work piece contact work at the same time A WARNING Always use hearing protection to protect your ears against IW hearing loss due to exhaust noise Always wear proper safe ty glasses to prevent injuries to the eyes from fragments of the work piece defective nails or other debris caused by using the clipped head nailer All safety glasses must have side shields and should conform to the requirements of the American National Standards Institute ANSI 287 1 Failure to comply with this warning could lead to serious or permanent damage to the ears as well as serious damage or permanent blindness in the eyes Never carry the clipped head nailer by the air hose A sudden disconnection of the air hose could cause the clipped head nailer to remain charged and an accidental firing could occur Failure to comply with this warning could lead to serious injury to the operator or bystanders Always disconnect the power source and ensure the tool is not charged before loading fasteners Failure to comply with this warning could cause severe injury or death to the operator bystanders and severe damage to the clipped head nailer Never use a non relieving air coupler with the clipped head nailer Always use couplers that release any built up charge in the clipped head nailer s fir
21. in a list of repair facil ities in your area or to make arrangements to return the tool for service ACTION REASON OPERATION Clean magazine and Prevents clipped head Use compressed air and feeder mechanism nailer from jamming clean daily Inspect and ensure work Ensures operator safety piece contact operates and keeps clipped head Use compressed air and properly nailer working efficiently 12 daily Apply 2 3 drops of Extends life of clipped pneumatic tool oil to head nailer clipped head nailer air inlet after every use TROUBLESHOOTING Most minor problems can be resolved quickly and easily using the troubleshooting table below For problems that cannot be solved contact Customer Service toll free at 1 888 278 8092 Lubricate clipped head nailer after every use using pneumatic tool oil PROBLEM POSSIBLE CAUSE SOLUTION Check for jammed nail Clear jammed nail Ribbon spring weakened Reblace ribbon sirin or damaged p prng Nailer operates but no Clean and lubricate nail Inspect nail feeder A feeder mechanism Use ONLY recommend Ensure correct nails are i ed nails being used nail is driven PROBLEM Weak drive Slow to cycle between nailings Nails driven too deep Clipped head nailer feeds intermittently or skips nails Nails jam or driven nail is bent Drives nails properly during normal nailing operations but fails to drive nails fully at f
22. ing mechanism A non relieving air coupler can allow the clipped head nailer to dis charge a fastener while the tool is disconnected from the power source Failure to comply with this warning can result in serious or permanent injury or even death to the operator or to bystanders Do not drive nails on top of other nails Do not operate the clipped head nail er at too steep of an angle Nails can ricochet Failure to comply with this warn ing can result in serious injury or even death to the operator or bystanders Do not modify the clipped head nailer in any way Unauthorized alterations can jeopardize safety in the tool s operation Failure to follow this precaution can result in serious injury or even death to the operator or bystanders On rooftops and other high locations always move forward as you use the clipped head nailer You can easily loose your footing if moving backwards When nailing against a perpendicular surface nail from the top down This causes less fatigue and reduces the chances of accidents Ensure the work area is sufficiently illuminated to operate power tools The work area should be clear and free of litter 5 A WARNING Thoroughly clean and maintain the clipped head nailer after every use Lubricate moving parts to prevent rust and minimize friction related wear Wipe down the entire tool and remove all dust from the moving parts Properly store the clipped head nailer in a suitable case to ke
23. ments of this manual MAINTENANCE gt sseeg peia c yy Re ge d 16 17 MANDATORY MAINTENANCE 00 ccc cece eee ee eeeees 18 A du A uim alert nee l is e E a TROUBLESHOOTING aaa 18 19 EI TI de Pec A safety messages that follow this symbol to avoid PARTS DIAGRAM 000 cece RR RR n 20 21 possible injury or death PARISEIST xe ous usd a a M AR E LES 22 25 SPECIFICATIONS 2 1 utt d ku andes Edere ice ue ies 25 A DANGER DANGER indicates an imminently hazardous 1 YEAR LIMITED WARRANTY 26 28 situation which if not avoided will result in death or serious injury A WARNING WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury A CAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury CAUTION used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage CAUTION NOTE provides additional information that is useful for proper use and maintenance of this tool If a NOTE is indicated make sure it is fully understood NOTE In addition to SAFETY ALERTS listed above there could also be numerous symbols alerting the operator that specific safety equipment is required to safely operate this tool Learn these SAFETY SYMBOLS as well as the SAFETY ALERTS to prevent injury to the operator and to bystanders READ OPERATING
24. re it is functioning within the proper pressure range 4 WARNING Using an air pressure of more than 120 psi can pe cause the clipped head nailer to malfunction or possibly explode 4 causing severe injury or property damage DE SELECTING A PROPER AIR HOSE Use an air hose with the largest diameter and shortest length possible to ensure continuous efficient nailing operations Using an air pressure of 70 psi 5 0 kg cm G an air hose with an inside diameter of 1 4 6 5 mm or greater and a hose length of less than 6 6 ft 20 m it is recommended that a 0 5 second interval be allowed between each nailing Air supply hoses shall have a minimum working pres sure of 150 psi 10 7 kg cm G or 15096 of the maximum pressure produced by the compressor or whichever is higher A CAUTION Low air output by the compressor or a longer hose with a smaller inside diameter in relation to the nailing frequency may decrease the driving capability of the air nailer SELECTING A QUICK DISCONNECT 1 Remove the plastic protective plug a from the tool s air inlet lt 2 Insert a 1 4 NPT male quick MDD 1o disconnect into the air inlet Install the female portion to the air hose 8 To improve the connection between the quick disconnect and air nailer and to help prevent oxidation apply PTFE tape or joint compound to the connector threads before insertion 3 Snap the air hose onto the quick disconnect on
25. sign The repaired or replaced unit will be warranted under the terms of the remainder of the one year warranty period cov ered defective parts not subject to normal wear and tear or other exclusions will be repaired or replaced at Alltrade s option During the warranty period Alltrade will be responsible for the return shipping charges Alltrade s repair and or replacement of any nonconforming item and or part thereof shall constitute fulfillment of all obli 26 gations to the purchaser Alltrade shall not be responsible or liable for any expense including freight charges or repairs made outside Alltrade s facility or an Alltrade designated service unless expressly agreed to by Alltrade in writing Under no cir cumstances shall Alltrade bear any responsibility for loss of the unit loss of time or rental inconvenience commercial loss or consequential damages For the location of an Authorized Service Center nearest you please call customer service at 1 888 278 8092 EXCLUSIONS Air nailers and staplers need periodic maintenance to remain in proper operating condition Normal wear parts o rings and driver blades shall be warranted to the original purchaser to be free from defects in materials and workmanship for a peri od of 90 days from the original date of purchase This warranty does not cover parts damaged due to normal wear abnormal condi tions misapplication misuse abuse accidents operation improper storage or freig
26. tact Actuation Mode OPERATION IN SINGLE SEQUENTIAL ACTUATION MODE To select the Single Sequential Actuation Mode see Figure 1 1 Press and hold the red Actuation Selector embedded in the trigger 2 Rotate Actuation Selector down to the Single Sequential Actuation T 3 Release Actuation Selector ensuring locking tab is fully seated in the slot A CAUTION Ensure selector has locked into position Ensure actuation process is fully understood before attempting to use clipped head nailer TO USE THE CLIPPED HEAD NAILER IN SINGLE SEQUENTIAL ACTUATION MODE 1 Firmly grip clipped head nailer handle 2 Position clipped head nailer work piece contact on work piece surface 3 Push clipped head nailer against work piece compressing work piece contact 4 Pull trigger on clipped head nailer to drive nail The clipped head nailer will recoil away from the work piece as nail is driven 5 Remove finger from trigger and lift clipped head nailer away from surface of work piece OPERATION IN CONTACT ACTUATION MODE A WARNING When using contact actuation mode be careful of unin tentional double fires resulting from tool recoil Unwanted fasteners may be driven if the work piece contact is allowed to accidentally re contact the work piece 10 To select Contact Sequential Actuation Mode see Figure 2 1 Press and hold Actuation Selector embedded in the trigger 2 Rotate Actu
27. y with this warn ing could result in serious injury or even death to the operator Keep bystanders children and visitors away from area where clipped head nailer is being used Distractions can result in severe injury or even death to anyone who inadvertently gets in the way of nailing operations Do not use oxygen combustible or bottled gases such as carbon Pain dioxide or nitrogen as a power source for the clipped head nailer Use only compressed air from a source as outlined in this manual The tool will explode resulting in severe injury or even death to the operator and bystanders A WARNING Do not connect clipped head nailer to an air source capable of d generating more than 200 psi 14 06 kg cm G Over pressurizing the clipped head nailer will result in bursting abnormal operation or breakage of the tool Use only clean dry regulated compressed air at levels specified on the tool Failure to comply can cause severe injury or death to the operator or bystanders Do not attempt to fasten the trigger in the ON position This could lead to an accidental discharge of the clipped head nailer Do not operate the clipped head nailer if any portion of the tool s operating controls are inoperable discon nected altered in any way or not in proper working order Failureto comply with this warning could result in serious injury or even death to the operator or other bystanders b19 3 Pressure regulators must
Download Pdf Manuals
Related Search