Smeg S2773CXU Instruction Manual
Contents
1. When installing a range under existing cabinets and the installation does not satisfy the minimum cabinet clearances install a range hood above the cooktop to avoid burn hazards Instructions for the Installer 3 POSITIONING THE COOKTOP AND LOCATION REQUIREMENTS NOTE The following operation requires building and or carpentry work and must therefore be carried out by a competent technician Installation can be carried out on various material such as masonry metal solid wood plastic laminated wood etc As long as they are heat resistant T 90 C 194 F Observe all governing codes and ordinances Do not obstruct flow or combustion and ventilation air Itis the responsibility of the installer to comply with installations guidelines specified the model serial I D plate The model serial 1 0 plate is located on the bottom of the cooktop burner box The cabinet opening dimensions that are shown must be used Given dimensions are minimum clearances A grounded electrical supply is required See the 4 Electrical connection section The measurements in the tables referring to the figure below must be followed when attaching the appliance to the support structure Cooktop width 30 758 mm 36 900 mm Cooktop width 30 762 mm 36 111 014 29 1 5 750 mm 35 1 5 892 mm 28 3 5 721 33 73 863 Instructions for the Instal2. 70 ELECTRICAL CODE LATEST EDITION or the CANADIAN ELECTRICAL CODE 22 11 1982 and CAN CSA C22 2 61 or latest edition and all local codes and ordinances Before you plug in the electrical cord make sure that all the controls are in the OFF position Never modify or alter the construction of the appliance CAUTION This unit is designed as a cooking appliance Based on safety considerations never use it for warming or heating a room Immediately after installation inspect the appliance following the instructions in this booklet If the appliance doesn t work properly disconnect it from the electrical power supply and call the technical assistance center Do NOT attempt to repair the appliance Any adjustment and servicing must only be performed by qualified cooker installers or service technicians Do not leave the packaging in the home Separate the various waste materials and take them to the nearest specialized waste collection facility SAVE AND KEEP THIS BOOKLET Instructions for the Installer 2 COOKTOP MEASUREMENTS NOTE Observe all governing codes and ordinances 77 Some cabinet and building materials are not designed to withstand the heat produced by the cooktop Check with your builder or cabinet supplier to make sure that the materials used will not discolor delaminate or sustain other damage Cabinet opening dimensions that are shown must be used Given dimensions are minimum clearances
3. NOTE Both power cables coming out of the cooktop must be connected according to the diagrams 77 shown pictures 1 and 2 11
4. Table of Contents 1 IMPORTANT SAFETY INSTRUCTIONS 4 2 GOOK POP MEASUREMENTS cco svete 6 POSITIONING THE COOKTOP AND LOCATION REQUIREMENTS 7 SM 9 MELE TRIGA CONNEC GIN 10 TECHNICIAN ANY TECHNICAL PROCEDURES MUST BE CARRIED OUT BY AUTHORIZED NOTE THIS APPLIANCE MUST BE INSTALLED SOLELY AND EXCLUSIVELY BY A QUALIFIED 77 INSTRUCTIONS FOR THE INSTALLER these are intended for the qualified engineer who is able to X install commission and test the appliance Important Safety Instruction 1 IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS Your Safety And the Safety of Others Are Very Important We have provided many important safety messages throughout this manual and on your appliance Read all instructions before using your appliance and always obey all safety messages RECOGNIZE SAFETY INFORMATION This is a safety alert symbol This symbol alerts you to potential hazards that can kill or hurt you and others UNDERSTAND SIGNAL WORDS A signal word DANGER WARNING or CAUTION is used with the safety alert symbol DANGER identifies the most serious hazards It means you can be killed or seriously injured if you do not immediately follow the instructions WARNING means you can be killed or s
5. eriously injured if you do not follow the instructions CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury All safety messages will inform you of potential hazards on how to reduce the risk of injury and what can occur if the instructions are not followed IMPORTANT Installation and grounding must comply with applicable codes Observe all government codes and ordinances NOTE This cooktop is NOT designed for installation in manufactured mobile homes or for installation in Recreational Park Trailers DO NOT install this cooktop outdoors Important Safety Instruction To reduce the risk of fire electrical shock injury to persons or damage A WARNING when installing the cooktop some basic precautions must be followed including Read all instructions Proper installation is your responsibility Have a qualified technician install and ground this appliance in accordance with these installation instructions It is the responsibility of the installer to comply with the installation clearances specified on the model serial I D plate The I D plate is located under the cooktop base ELECTRICAL GROUNDING REQUIRED See the 4 Electrical connection section It is the customer s responsibility 1 contact a qualified electrician to install the appliance 2 To ensure that the electrical system is adequate and in conformance with the national ANSI NFPA
6. ler B 19 aL 500 mm 19 500 MODEL WITH FRAME MINIMUM DISTANCE C D E S a 225 145mm 50mm 50 mm 5 2 33 2 73 145mm 50 50 MODEL WITHOUT FRAME B DET 485 mm 19 1 6 485 mm MINIMUM DISTANCE D E a Di 145 50 50 277 27 145mm 50mm 50 mm F 19 16 1 9 16 20 40 1 he 20 40 mm Sg 1 9 16 20 40 1 9 16 20 40 mm G 30 758 mm 36 900 mm 30 14 762 mm 36 GG 914 mm Instructions for the Installer CEN 2 3 1 Mounting Before mounting the device to the unit lay the provided adhesive sponge onto the glass surface to separate it from the unit After fixing the provided adhesive sponge B to the glass mount the device to the unit using the mounting brackets A provided as shown in the figure NOTE This appliance must not be built in above a dishwasher Installation of an oven without a cooling fan underneath the cooktop is forbidden Pass the power supply cable through the back of the unit making sure that it does not touch the bottom casing of the cooktop or the oven if any installed below it 10 Instructions for the Installer 4 ELECTRICAL CONNECTION ELECTRIC SHOCK HAZARD Disconnect power to the junction box before making connection Electrically ground the appliance with green or green yellow colored wire D
7. ly grounded Do not modify the power supply cord If it will not fit in the outlet have a proper outlet installed by a qualified electrician Refer to picture 1 where local codes allow the tom connection of the ground wire to the branch circuit neutral wire white colored wire Junction Red Black The ground wire must be connceted first wire i f local codes permit connect the green or yellow green ground wire from the appliance White and the white wire from the appliance to the i branch circuit neutral wire white colored wire D Connect the red and gray leads from the White and green or cooktop to the junction to the corresponding yellow green 5 leads in the junction box Cable from Tuned cooktop conduit 1 Refer to picture 2 Cable from power supply The ground wire must be connceted first Connect the green or yellow green ground wire i wires from the appliance to the ground in the junction box green colored wire Do not connect the grounding wire to the neutral wire in the junction box Connect the red and gray leads from the appliance to the corresponding leads in the WIZ Black 5 Greeen or wires Junction box yellow green Grounding cance Cable from UL listed cooktop Connect the white wire from the appliance to the conduit neutral white colored wire the junction box connector pic 2
8. n Batterymarch Park Quincy Massachusetts 02269 CSA International 8501 East Pleasant Valley Road Cleveland Ohio 44131 5575 This appliance is manufactured with a yellow green ground wire connected to the appliance frame After making sure that the power has been turned off connect the flexible conduit from the appliance to the junction box using a U L listed conduit connector Picture 1 and Picture 2 and the instructions provided below are the most common way of connecting the appliance Your local codes and ordinaces of course take precedence over these instructions Complete electrical connections according to local codes and ordinances This cooktop must be connected to a grounded metallic permanent wiring system or a ground connector should be connected to the ground terminal or wire lead on the cooktop Connection at connection block must be copper wire only Instructions for the Installer NOTE Use this method only if local codes allow connecting the cabinet ground conductor to the neutral wire of the power supply cord WARNING ELECTRIC SHOCK HAZARD Turn power supply off before connecting wires Electrically ground the range Failure to follow these instructions can results in death fire or electrical shock Improper connection of the device grounding conductor can result in a risk of electric shock Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is proper
9. o not ground to a gas pipe Check with a qualified electricial if you are not sure that the range is grounded Do not have a fuse in the neutral or ground circuit FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DEATH FIRE OR ELECTRICAL SHOCK Make sure that the voltage and capacity of the power line conforms to the data shown on the 1 0 plate SE located under the casing Do not remove this plate for any reason If codes permit and a separate ground wire is used it is reccomended that a qualified electrician determine that the ground path is adequate When a four wire or three wire single phase 120 240 volt 60 Hz AC only electrical supply is available 50 ampere maximum circuit protection is required if specified the model serial I D plate when a four wire or three wire single phase 120 208 volt 60 Hz AC only electrical supply is available a 40 ampere maximum circuit protection is required fused on both sides of the line A time delay fuse or circuit breaker is recommended model serial 1 0 plate is located on the drawer Wire size and connections must conform to the requirements of the National Electrical Code ANS NFPA 70 Latest edition or CAN CSA Standard C22 1 Canadian Electrical code Part 1 Latest edition and all local codes and ordinances for the kilowatt rating of the range Copies of the standards listed may be obtained from National Fire Protection Associatio
Download Pdf Manuals
Related Search